API Marine. BMS Presentation. Ballast Measurement Systems

Transcription

1 API Marine BMS Presentation Ballast Measurement Systems

2 BMS4 Typical Configuration

3 BMS4 Typical Configuration

4 BMS4 Extended Configuration

5 BMS4 System (24 tanks) Air regulator Terminal block Drain/Air Filter Main switch BMS Box (12 Channels) BMS Box (12 Channels)

6 BMS4 Overview

7 BMS4 overview

8 BMS4 Advantages System integrated in one compact cabinet Modular concept Standard configuration Tailor made solutions for any application Ideal for retrofit Installations Can easily be adapted to existing/onboard solutions Works with any pressure, level and temperature of liquid Automatic diagnostic during operation

9 BMS4 Advantages Automatic calibration of sensor during operation Automatic and continuous cleaning during operation Less depending of air quality Reliable system for continuous operation

10 BMS4 Technical specifications Total number of control points for level up to 100 points Draft control up to 6 points Power supply 220 V Power consumption up to 1.5W /channel Sensors power supply 24 V DC Protection level of operator station IP20 of local technological station IP54

11 BMS4 Operation System API Marine API ApS Marine Troensevej ApS Troensevej 12 DK Aalborg DK-9220 Oest Aalborg Tel.: Oest Tel.: Fax:

12 BMS4 LTS4 Local technological station LTS performs the following functions: level measurement, by means of measuring backpressure, which occurs in air mains of ballast tanks Transfer of information of measured values into the controller of the cargo system

13 BMS4 Operating principle of the system Data processing unit performs cyclical scanning of the sensors: Contents of the measurement cycle: Air injection into measuring tubes Time delay for pressure equalization Measurement of pressure, equal to pressure in ballast tanks Periodic calibration of sensors is performed

14 BMS4 Installation aspects Easy installation Designed for installation on ship Cabling, mounting etc.

15 BMS4 Scope of Supply (1-12 Tanks) BMS4 System (1-12 tanks) System consisting of Local Technological Station LTS4 (for wall mounting) BMS4 Module with 1-12 Measuring channels (1 pc) Air Separator Unit Pressure Regulator Unit Measurement error: <0.25% of the max. value of the measuring range Power supply: 24 VDC. Output: Modbus RTU, RS485 2-wires Pneumatic connection: 10mm x 1mm stainless steel tubing Filter and pressure reducer with manometer is provided for air inlet. Shut-off valve for air supply. Low pressure alarm switch (NC). Atmospheric correction for pressure sensors. Air pressure injected in cabinet: 4-8 bar. Automatic system calibration Working air pressure less than 2 bar Cabinet dimensions: 600x600x210mm. Manuals and documentation. Standard Spares and tools

16 BMS4 Scope of Supply (1-24 Tanks) BMS4 System (1-24 tanks) System consisting of Local Technological Station LTS4 (for wall mounting) BMS4 Module with 1-24 Measuring channels (2 pc) Air Separator Unit Pressure Regulator Unit Measurement error: <0.25% of the max. value of the measuring range Power supply: 24 VDC. Output: Modbus RTU, RS485 2-wires Pneumatic connection: 10mm x 1mm stainless steel tubing Filter and pressure reducer with manometer is provided for air inlet. Shut-off valve for air supply. Low pressure alarm switch (NC). Atmospheric correction for pressure sensors. Air pressure injected in cabinet: 4-8 bar. Automatic system calibration Working air pressure less than 2 bar Cabinet dimensions: 600x600x210mm. Manuals and documentation. Standard Spares and tools

17 BMS4 Installation NRV Typical tank installation with Non Return Valve (NRV) NRV mandatory for Fuel Tanks, however should be considered for all tank Non Return Valve

18 Non Return Valve

19 1:1 Converter Requirement for Fresh Water Tanks

20 BMS4 Retrofit Possibility to replace existing older systems. Tubes, connections etc. may be kept as is. Easy and cost effective installation

21 BMS5 Single Channel BMS Single Channel BMS Sensor Output 4-20mA, HART Power Supply 24VDC Accuracy: 0,3%

22 API Marine Setting new standards for tank measurement technologies