Sealing of Masonry
Contents This brochure mainly deals with sealings in masonry structures made from different mineral building materials. These also include porous concrete and stamped concrete. Another WEBAC Brochure deals with the sealing of cracks in reinforced concrete. A sealing effect is obtained or restored by introducing liquid synthetic resin into porous building structures, which forms a barrier over the entire cross section upon conclusion of the curing process. The water in the capillary and porous structure of the building materials is displaced and permanently replaced by the sealing material by means of pressure injection. This applies not only to post-construction damp-proof against capillary rising moisture but also to higher stress levels such as pressurized in-situ water. A wide range of special injection materials for such applications is presented below. NOTE Please observe all existing regulations and the instructions in the technical data sheets on the respective WEBAC Products. If you have any queries or specific problems, please do not hesitate to contact us. Introduction Damp masonry... 1 Damage Diagnosis Building state analysis... 2, 3 Reconstruction Effects of capillary-obstructing injection systems.... 4 Effects of different injection materials... 5 PU injection foam resins (SPUR).... 6 PU injection resins (PU)... 7 Injection packers and pumps for PU resins... 8 Acrylate gels... 9 Injection packers and pumps for acrylate gels... 9 Alkali silicate/alkali siliconate... 9 Application Pressure injection with WEBAC injection resins....10, 11 Sealing of multi-shell masonry...12 Surface sealing...13 All the data given in this brochure are of an informative nature representing our current state of knowledge and are in no way binding. Any information regarding this brochure given by our employees is likewise non-binding. As the exact chemical, technical and physical conditions of the actual application are unknown to WEBAC, this information does not preclude examination of the products and procedures for the intended application by the user. WEBAC is thus unable to guarantee results. The user is fully responsible for the observation of existing regulations and requirements when using the products. With the publication of this brochure all previous versions are no longer valid. Copyright by WEBAC-Chemie GmbH. Reproduction and/or printing of extracts from this brochure is permitted only with the prior consent of WEBAC-Chemie GmbH. Version 04/14 2 Sealing of Masonry
Introduction Damp Masonry More than a visual shortcoming moisture-related damage to plinths and basement walls is one of the most common building defects in structural engineering. This damage can have different causes. Moisture-damaged masonry Structural components with ground contact are exposed to varying moisture stresses such as seepage water, soil moisture and ground water. Plinth areas are also exposed to stress caused by splashing water, ice, de-icing salt, etc. and to thermal stresses due to temperature fluctuations. Professionally designed buildings are provided with sealings which prevent moisture from penetrating the structure. However, building defects, changing conditions and aging of the building materials used lead to temporary or permanent moisture damage time and time again. The consequences of moisture penetration are varied: The thermal insulation value of the wall deteriorates, resulting in higher heat losses Spores, algae and fungi find an ideal breeding ground Salts penetrate the structural component and cause efflorescence to form, leading to chipping. This may impair the stability of the building in the long term. This is why effective measures against moisture pene tration are necessary to safeguard the building s usability and to protect its structure. REASONS FOR WET WALLS Capillary rising moisture Cracks and leaking joints in the wall structure Leaks at floor/wall junctions Defective vertical sealings Defects in atmospheric environment (insufficient ventilation, insulation, etc.) Salt-related hygroscopic dampness Damaged drainage, supply and return lines, etc. Changed moisture-related stress due to ground water or penetrating surface water Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 1
Damage Diagnosis Building State Analysis A thorough analysis of the state of the building is necessary for a suitable repair scheme and a sound refurbishment plan. General examinations General information on building (e.g. age, structural state, etc.) Use of adjacent rooms Air humidity and temperature in rooms Ground water conditions PH value of ground water, reference to acids (increased salt load) Assessment of foundation soil Construction Type of masonry (e.g. sand-lime brick, quarry stone, solid bricks, vertically perforated bricks, concrete, mixed brickwork) Wall thicknesses Masonry structure (single- or multi-shell, with or without air cushion) Wall homogeneity, strength, density and porosity Existing cracks and cavities, movements of structural component, if any Structure and position of foundation Supply lines Static assessment/stability Existing barriers, their position and nature Repair work already carried out Core removal from brickwork Large-format cyclopic brickwork with large-pored joints Moisture analysis The distribution of moisture in the structural components must be analyzed in order that the cause of damage can be determined and a suitable refurbishment scheme developed. Well calibrated, spatially resolved moisture determinations by means of moisture tomography have proved successful for non-destructive examinations of the building structure. More accurate values can be ascertained by taking masonry samples or removing cores, for example following the Darr method. The samples are analyzed to assess the actual moisture penetration gradient (MPG) at different struc tural component depths. The moisture penetration gradient (MPG) indicates the ratio between Natural brickwork with loam mortar joints existing moisture and maximum saturation moisture. Conversely, the open pore and capillary volume can also be determined. Hence, the quantity of injection material required can be roughly estimated. The WTA (International Association for Science and Techno logy of Building Maintenance and Monument Pre servation) has in its Code of Practice 4-4 defined the three categories 60/80/95 % MPG, according to 2 Sealing of Masonry
which injection materials can be tested and certified. In combination with pressureless or pressure injection, six variations arise for effectiveness checks. For certain injection materials, additional pretreatment measures such as drying of the masonry (e.g. for paraffin or certain alkali silicate preparations), alkaline activation or reaction phase up to the water load (e.g. silicon micro-emulsion concentrates) are required. Thanks to such complex pretreatment measures these injection materials can also be used at higher moisture penetration gradients. The alternative test proc edure according to BuFas (BuFAS Engineering Code of Practice IM-01/2009) is based on the determination of the distribution and hydrophobic effect of injection materials in masonry and mortar by means of wetting angle measurement and drop tests. With this procedure no MPG classes are preset, but the conditions actually prevailing during the test and the effectiveness of the injection material obtained in so doing are attested. Depending on the conditioning of the test samples, higher stress levels such as pressurized in-situ water can also be tested. Moisture due to salt-related stress Due to their hygroscopic (water-attracting) effect, watersoluble salts such as nitrates, chlorides, carbonates and sulphates may significantly increase the moisture content in the masonry. The salts crystallize on the surface of the structural component and cause efflorescence to form. This transition from the solved to the crystalline state often goes hand in hand with a strong increase in volume and crystallization pressure, which may cause damage to plaster or masonry. The salts can be analyzed according to type and quantity and the distribution of the most important salts detrimental to the masonry determined by means of samples from the masonry. The proportion of hygroscopic moisture of the total moisture penetration gradient can thus be ascertained and suitable accompanying measures can be taken. Moisture distribution at different moisture-related stresses Causes of moisture-related stress on masonry according to the WTA Outside Outside Outside Inside Inside Inside Outside Inside Outside Outside Outside Inside Inside Outside Inside Outside Inside Outside Outside Inside Inside Inside Outside Inside Outside Outside Outside Inside Inside Inside Insid Capillary rising moisture Vertically penetrating moisture Condensate formation due to falling short of dew point temperature CALCULATING MOISTURE PENETRATION GRADIENT GF - GT MPG = x 100 % GS - GT MPG Moisture penetration gradient GF Mass of damp sample GT Mass of dry sample GS Mass of water-saturated sample Hygroscopic moisture caused by salts absorbing moisture from ambient air Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 3
Reconstruction Effects of Capillary-Obstructing Injection Systems Besides a capillary network, the structure of plinths and basement walls usually also has cavities, gaps, cracks and large pores. Masonry joints are generally characterized by the greatest porosity. Water penetrating in to structural components through this structure and spreading thus causes moisture damage. Pressure injections can be carried out, above all into the masonry joints, to put a stop to capillary water transport preventing the moisture from spreading and rising. A moisture equilibrium is then established in the masonry above the sealing level. Masonry Masonry joint RISING MOISTURE Moisture spreads within the masonry because of the capillary absorptivity of the building materials mortar and bricks. They absorb the water like a sponge and distribute it within the structural component. The extent to which the water spreads in the structural component mainly depends on the diameter of the capillaries. The smaller the pores the higher the capillary absorptivity and the higher the moisture can rise in the masonry. If the pores are very small and unconnected (micropores or gel pores), for example in standard-compliant concrete, there is no capillary water transport. Disruptions in the capillaries, for example due to pores, prevent or delay the capillary moisture transport. If the capillaries are very wide, i.e. their pore radii exceed approx. 1 mm, no capillary water transport is possible either because the pores act as capillary-breaking layers, but large quantities of moisture can penetrate into the structure through these wide areas in the case of pressing water. Drill hole Diagram: capillary obstruction Injection resin Capillary Capillary-obstructing materials such as polyurethane injection resins and acrylate gels are also able to entirely fill larger cracks and gaps within the injection level. In the process, cracks and cavities which penetrate the external sealing and are therefore responsible for the moisture penetration are also filled. The PU injection resin is barely vulnerable to attack by in-situ water. Thanks to the capil lary-obstructing filling process the injection material cannot be washed out.in case of higher stress levels (up to pressurized in-situ water), these materials are often the only suitable sealing solution. 4 Sealing of Masonry
Reconstruction Effects of Different Injection Materials The injection material spreads away from the drill hole into the joints and bricks, first filling large openings such as cracks and gaps. The material then penetrates capillaries and pores and more and more fine structures. Under pressure, damp areas and areas filled with water are penetrated and the water is partly displaced from the structure. The effects of different injection materials are illustrated (standing below). 1 OBSTRUCTION 2 CONTRACTION The capillary/pore structure is entirely filled, putting a stop to all capillary water transport in the long term, irrespective of the moisture penetration ratio. Injection materials: e.g. polyurethane, paraffin (restriction: system-related pre-drying), acrylate gels (restriction: shrinkage during the drying process) The capillary/pore structure is contracted, reducing the capillary absorptivity. The drying effect is obtained due to the higher evaporation speed than the capillary transport speed. Injection materials: unknown 3 WATERPROOFING 4 WATERPROOFING/CONTRACTION Water-repellent compounds deposit on the capillary walls, so that the water rises to a lesser extent in the capillaries, impeding the water transport. The pore structure remains largely intact. Injection materials: e.g. silicon micro-emulsion concentrates, silanes, siloxanes Combination of 2 Contraction and 3 Waterproofing Injection materials: combinations of alkali silicate and siliconate (e.g. modified silica sols) Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 5
Reconstruction Products The success of an effective damp-proof course (dpc) mainly depends on the selection of the right injection material. A description of WEBAC Products and their areas of application and properties is given below. PU Injection Foam Resins (SPU) Quick-foaming polyurethane injection foam resins (SPU) are specially designed to fill the essential parts of masonry full of gaps and cavities. Upon contact with water, the resins form a foam of fine cellular structure during a very quick reaction which fills all free volumes and also displaces the water from the building structure. Thanks to the intensive mixing process, a barrier forms very quickly and the water transport is stopped, especially with pressing water. Preliminary injection of a PU injection foam resin into masonry full of cavities Technical parameters * WEBAC 150 WEBAC 151 WEBAC 157 Mixing ratio 1 : 1 parts by volume 1 : 1 to 1 : 10 parts by volume 1 : 1 parts by volume Expansion in volume given free expansion up to approx. 40-times 1 : 1 VT 1 : 5 VT 1 : 10 VT 10- to 15-times 30- to 35-times 25- to 30-times 15-times Reaction time (21 C) with 10 % water Start End 14 s 65 s 1 : 1 VT 8 s 30 s 1 : 5 VT 15 s 70 s 1 : 10 VT 20 s 100 s 20 s 80 s Reaction times of WEBAC 150 and WEBAC 157 can be accelerated with WEBAC B15. Application temperature > 5 C > 5 C > 5 C Application Injection with 1C/2C Pump Injection with 1C Pump Injection with 1C/2C Pump Universally applicable Reliable application Fast and highly expanding foam Universally applicable Variable reaction time Elastic foam texture Low expansion pressure Special properties * The specified data are values determined under laboratory conditions and are subject to certain fluctuation. Deviations are possible in practice depending on the respective object situation. 6 Sealing of Masonry
PU Injection Resins (PU) WEBAC 14** Capillary obstruction is achieved by pressure injection of solvent-free, low-viscosity, 2-component polyurethane injection resin. This material is suitable for almost any type of masonry and can also be used for water-satu rated structural components. Polyurethane injection resin spreads in gaps, cavities, cracks and pores, fills these completely and adheres very well to the mineral building materials.at the same time the capillaries are obstructed, ensuring a durable insulating effect, i.e. the active substance can no longer be washed out. Moreover, the functionality of the material is not impaired by existing salts. Polyurethane injection resins do not bring any additional water into the masonry but, upon contact with water, form small pores which are incorporated in the resin matrix. This way polyurethane injection resins have a positive effect on the heat balance of the masonry and reduce the formation of thermal bridges. Techn. parameters * WEBAC 1401 WEBAC 1403 WEBAC 1404 WEBAC 1420 WEBAC 1440 Mixing ratio (parts by volume) 3 : 1 1 : 1 3 : 1 3 : 1 3 : 1 Viscosity of mixture (23 C) 45 mpa.s 80 mpa.s 110 mpa.s 300 mpa.s 250 mpa.s Processing time (23 C) 120 min 90 min 60 min 100 min 120 min Application temperature > 5 C > 5 C > 5 C > 5 C > 5 C Moisture penetration gradient max. 95 % > 95 % > 95 % > 95 % > 95 % Application Injection with 1C Pump by low or high-pressure method Injection with 1C Pump Special properties Effectiveness tested Extremely low viscosity Low foam development Good penetration Mainly based on renewable raw materials WTA Code of Practice 4-4 Low viscosity Quick seal foam structure upon contact with water Universally applicable Reliable application BuFAS Engineering Code of Practice IM-01/2009 Very economical use Mainly based on renewable raw materials High chemical resistance also to biogenous sulphuric aid Compatible with bitumen Tested microbiologically (W 270 test according to DVGW regulations) * The specified data are values determined under laboratory conditions and are subject to certain fluctuation. Deviations are possible in practice depending on the respective object situation. Tear resistant foam structure Resistant to mechanical stress Dynamically stabilizing Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 7
Reconstruction Products PU Injection Resins (PUR) WEBAC 16** For surface injections within the masonry structure, a stabi lizing effect can be obtained in addition to the sealing effect when filling cavities. The polyurethane re sins described above (WEBAC 14**) are used for sealing structures against moisture and have only secon dary sealing properties. The new generation of compression-proof polyurethane resins, WEBAC 1610 and WEBAC 1660, is adapted to the compressive strength of the masonry and therefore also has a stabilizing effect without affecting the masonry structure. Injection pumps for PU resins When applying PU injection resin using single-component pumps, both components are mixed beforehand and then filled into the pump s hopper. When using 2C Pumps, pre-mixing is not required. Both components are introduced to the mixing head separately and mixed here. This pump technology is especially recommended when applying large quantities of very quick-reacting injection materials. The water reactivity of solid polyurethane resins is respon sible for an accelerated curing process in masonry exposed to moisture, even at very low temperatures of down to 1 C. Thanks to the micro foam formation upon contact with water, cross-linking of the injection material is quicker and often obviates the need for patching measures. The same injection technology as for tradi tional damp-proof course (dpc) can be used to apply these products. With surface injections, several rows of drill holes are made systematically above each other. Injection packers for PU resins Injection packers are filler necks which connect the struc tural component to the injection pump during the injection process. WEBAC Mechanical Packers are bonded with the surface by screwing them into the drill hole. When the packer is tightened, the rubber sleeve is firmly pressed against the drill hole wall. WEBAC IP 2 WEBAC IP 2K-F2 Technical parameters * WEBAC 1610 WEBAC 1660 Mixing ratio 1 : 1 parts by volume 1 : 1 parts by volume Processing time (23 C) 35 min 25 min Application temperature > 5 C > 1 C Application Injection with 1C or 2C Pump Injection with 1C or 2C Pump Special properties tough and solid very good penetration fast curing with or without water slight foam formation upon contact with water with accelerator also suitable for use at low temperatures very high compressive and bending tensile strength fast curing with or without water slight foam formation upon contact with water with accelerator also suitable for use at low temperatures * The specified data are values determined under laboratory conditions and are subject to certain fluctuation. Deviations are possible in practice depending on the respective object situation. 8 Sealing of Masonry
Acrylate gels Acrylate gels are usually aqueous 3C Injection Materials with a very low viscosity of < 10 mpa s. The materials are particularly suitable for thick structural components and obstruct the capillaries in the masonry like PU injection resins. They can also be used in case of salt-related stress and high moisture penetration gradients. Acrylate gels are applied by means of pressure injection with a 2C Pump and are also suitable for surface sealings within open-pored building structures. The material can reversibly absorb and discharge water and should therefore only be used in areas with ground contact. ACRYLATE GELS WEBAC 240/WEBAC 250 For product properties and more detailed technical information, please see the Technical Data Sheets. Injection packers for acrylate gels WEBAC Acrylate Gels are applied by means of WEBAC Mechanical Packers provided with button head fittings on which the injection hose is installed. If the building structure is stable enough to bear the impact, WEBAC Hammer-in Packers which are knocked into the drill hole are an alternative. They are anchored to the surface by lamellae positioned in toroidal formation. Alkali silicate/alkali siliconate Alkali silicate and alkali siliconate are so-called silification materials which are still widely used, but their application and functionality are very limited. In masonry with a maximum moisture penetration gradient of 50 % and largely free of salt-related stress, these diluted waterglass solutions initially increase the moisture penetration gradient and finally contribute to a certain capillary contraction during the drying process. To start the silification process, cross-linking of the sili - cic acid must be activated by CO 2 from the air. This re sults in a discharge of additional salt in the form of alkali carbo nate within the masonry which remains on the mason - ry surface as efflorescence during the drying process. Thick masonry cross-sections cannot be reached with this method. The frequently used siliconate additive has a certain water proofing effect. Even if the bottles for alkali silicates are still a common sight, an adequate distribution of silicic acid over limited masonry cross-sections can only be achieved by pressure injections. SILICATE INJECTION GROUT WEBAC 2100 For product properties and more detailed technical information, please see the Technical Data Sheets. Injection pump for acrylate gels WEBAC IP 2K-F1 2C Pump specially designed for the application of acrylate gels. All pump components which come into contact with the material are made from stainless steel. Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 9
Application Pressure Injection with WEBAC Injection Resins Preparatory work Polyurethane injection resins and acrylate gels are applied by pressure injection via drill hole packers. The dis tribution of the injection material is more even and the penetration depth and efficiency are much higher than in the case of non-pressure injections. Drill hole spacing x z The distance between and the size of the drill holes depend on the structural conditions and the packers used. A distance of 10 12.5 cm between drill holes has proven effective. Deviations are possible depending on the onsite situation (for example with irregular masonry). The drill hole depth should reach at least 3/4 of the wall thickness (see diagram). With higher wall thicknesses, the packers should be positioned in two rows to facilitate the distribution of the injection material. The drill holes should be positioned approx. 8 cm above the first drill hole level, staggered by half of the drill hole distance. The drill holes should cross at least two bed joints to ensure ideal material distribution. DRILL HOLE DIAMETER Usually and unless specified otherwise, the drill holes for mechanical packers are made 1 mm larger than their diameter. As for hammer-in packers, the recommended drill hole size cor responds to the diameter of the packer. Usually, the drill holes are made into the brickwork slanting downwards at an angle of 30 45, depending on the wall thickness (Fig. 2). Preferably, the drill holes are made into the bricks to ensure that the injection packers are fastened tightly enough. Prior to injection, compressed air must be blown through the drill holes to remove deposits and drill dust (Fig. 3). x x x x: 10 12.5cm (one row) y: 20 25cm (two rows) Injection procedure z: approx. 8 cm (depending on brick format!) The injection material is injected until the pores are closed by saturation of the joints and the material can be seen emerging from the masonry into the area of the adjacent packer (Fig. 5). In the event of leaks, interrupt the injection procedure and patch any cracks and loose joints. As the mortar in the bed joints is usually more porous than the bricks are, it is neces sary to primarily fill the masonry joints with injection material during pressure injection. In so doing, the penetration depth is very high, particularly in the area between mortar and masonry. Consequently, the injection material displaces the water in the capillary system. Leaks, cracks and cavities can thus be sealed in one process, solving the problem of moisture penetration. During the injection procedure, the material penetrates the capillary structure creating a continuous, horizontal active level. A secondary injection must be carried out within the application time of the injection material in order to complement capillary migrated material. y Mechanical packers are then installed in the drill holes and tightened (Fig. 4). Suitable hammer-in packers made of plastic can also be used. The injection hose must fit comfortably on the injection nipple, otherwise it may be necessary to use a longer packer. Remove loose plaster layers. Loose joint mortar must be patched with WEBAC Quick Set Cement or WEBAC Putty to ensure the necessary pressure buildup for the material distribution in the masonry and to avoid any uncontrolled emergence of injection material. Schematic view of a damp-proof course (dpc) > 5 cm 10 Sealing of Masonry
Final work THE MATERIAL CONSUMPTION... Remove any soiling from the surface immediately after the injection procedure. Disassemble the drill hole packers following the curing process of the injection material. Knock off hammer-in packers at surface level. Then close the drill holes with a suitable mortar. Damp masonry may give off moisture to the environment for quite a while even after installing a damp-proof course (dpc). For this reason diffusion-inhibiting coatings and plaster must be removed to enhance the drying process. Existing salts may cause efflorescence to form on the surface of the structural component. All salt deposits must be removed to prevent hygroscopic humidity absorption. It may be necessary to implement other measures such as artificial room drying, controlled ventilation, application of reconstruction plaster (WTA) or measures to fight fungi. 100 cm 10 cm depends on the pore and cavity volume of the masonry. Rule of thumb: 1 kg/100 cm/10 cm wall thickness. For masonry with wall thickness > 60 cm: 1.2 kg/100 cm/10 cm wall thickness Fig. 1: Brickwork with rising moisture Fig. 4: Setting of mechanical packers Fig. 2: Making of drill holes Fig. 5: Injection of PU injection resin Fig. 3: Extraction of drill dust Fig. 6: Closing of drill holes Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH Accompanying measures 11
Application Sealing of Multi-Shell Masonry When multi-shell masonry is refurbished, injection material may penetrate the air cushion in the gap between the shells in an uncontrolled manner. To prevent this, the gap is filled with WEBAC 2260, a polyurethane casting foam resin. This also improves the thermal insulation effect of the air cushion. WEBAC 2260 WEBAC 2260 is a PU casting foam resin for rigid, compression-proof filling of cavities, gaps and spaces and is characterized by its excellent adhesion to dry and moist, absorptive and non-absorptive substrates. To improve thermal insulation and watertightness, WEBAC 2260 can be used for filling cavities in two-shell masonry, spaces between metal and mineral substrates, cavities in wooden structures as well as for wall breakthroughs and similar sealing tasks. The material is applied manually via filling openings or drill holes/lances using a 2C Injection Pump. Slowly expanding, the material cures to form a hard, compression-proof, closed-cell foam and acts as a vertical sealing on the entire surface. At the same time, the material forms an ideal abutment for a post-construction horizontal damp-proof course (dpc). WEBAC 2260 can for example also be used to fill the chambers in large-format hollow bricks. The reaction time and expansion volume of the foam can be adjusted by adding an accelerator. Filling of cavities in two-shell masonry Application of WEBAC 2260 Techn. parameters * WEBAC 2260 Mixing ratio Expansion in volume given free expansion up to approx. 1 : 1 parts by volume 4-times, up to 14-times with accelerator WEBAC B60 Reaction times Start End Application temperature > 5 C max. 30 cm 40 50 cm Application Special properties Casting Injection with 2C Pump Pressureproof rigid foam, also cures without water Thermal insulation effect Chlor ine- and CFC-free * The specified data are values determined under laboratory conditions and are subject to certain fluctuation. Deviations are possible in practice depending on the respective object situation. 12 Sealing of Masonry
Application Surface Sealings In the event of vertically penetrating moisture, an external sealing must be provided. The following WEBAC Products are suitable for this purpose: Bituminous acrylate dispersion Curtain injection WEBAC 5611 is a sealing compound for the sealing of surfaces against non-pressing and pressing water and fulfills the hydrostatic test requirements according to DIN 1048-5, 7.6. Even if applied at a layer thickness of only 1mm, WEBAC 5611 seals surfaces reliably against water pressures up to 7 bar. The product is also suitable for sealing horizontal balcony and terrace surfaces. WEBAC 240 is a polyacrylate gel for the post-construction surface sealing of structural components with ground contact, if conventional external sealings as described above are not feasible (see also WEBAC Brochure Curtain Injection). High-build bituminous coatings (KMB) according to DIN 18195 (DIN 18533 in future) WEBAC 5621, WEBAC 5622F and WEBAC 5622P are suitable for sealing surfaces against non-banked-up seepage water, non-pressing water and banked-up seepage water (DIN 18195 parts 4 6 or water exposure classes according to DIN 18533) for vertical and horizontal surfaces. Surface Sealing Brochure Sealing of Masonry 04/14 WEBAC-Chemie GmbH 13
WEBAC-Chemie GmbH Fahrenberg 22 22885 Barsbüttel/Hamburg Germany Tel. +49 40 67057-0 Fax +49 40 6703227 info@webac.de www.webac.de