SHIP SECURITY ALERT SYSTEM (SSAS)

Transcription

1 SHIP SECURITY ALERT SYSTEM (SSAS)

2 Your Local Agent/Dealer 9- Ashihara-cho, Nishinomiya, Japan Telephone : fax : All rights reserved. Printed in Japan FIRST EDITION : MAY. 00 ( DAMI PUB.No. OME- ) IC-07 * * * * * * *OMEA00* *OMEA00* * O M E A 0 0 *

3 TABLE OF CONTENTS SYSTEM CONFIGURATION.... OVERVIEW OF SSAS.... INSTALLATION.... Mounting..... Junction box (for FELCOM )..... SSAS alert unit Wiring Junction box (for FELCOM ) SSAS alert unit Initial Settings.... OPERATION.... Operation Mode..... Changing the password..... SSAS manager mode.... Setting SSAS Report Destination and Message Contents.... Transmitting SSAS Report Testing the Button...9. SSAS Report Test... OUTLINE DRAWING...D- INTERCONNECTION DIAGRAM...S-

4 SYSTEM CONFIGURATION Regulations require at least two SSAS alert units. FELCOM ANTENNA UNIT IC- DGPS 00//0/0 VAC φ, 0/0 Hz / VDC AC-DC Power Supply PR-0-CE* TERMINAL UNIT IC- GPS receiver OP- EGC Printer PP-0 Personal Computer (PC/AT compatible) Shipboard LAN (Ethernet) VDC Printer VDC Printer PP-0 CATEGORY OF UNITS Unit Terminal Unit Antenna Unit Other Units Mini Keyboard Distress Message Controller DMC- OR SSAS Alert Unit SSAS Alert Unit IC-07 IC-07 (Max. units) Category Protected from weather Exposed to weather Protected from weather JUTION BOX IC- * Any AC-DC power supply fulfilling requirements of IEC 09 may be used. Distress Alert/ Received Call Unit IC-0 Alarm Unit IC-0 Navigator : Standard Supply : Option : Local Supply

5 FELCOM ANTENNA UNIT IC- 00//0/0 VAC φ, 0/0 Hz - VDC COMMUNICATION UNIT IC- (with internal GPS receiver) * Any AC-DC power supply fulfilling requirements of IEC 09 may be used. AC-DC Power Supply PR-0-CE* FURUNO O POWER I INMARSAT MINI-C MOBILE EARTH STATION POWER LOGIN TX JUTION BOX IC- SSAS ALERT UNIT IC-07 ERROR PRINTER PERSONAL COMPUTER (PC/AT compatible) : Standard : Option : Local Supply : SSAS only CATEGORY OF UNITS Antenna Unit Exposed to Weather Communication Unit Protected from Weather Other Units Protected from Weather SSAS ALERT UNIT IC-07 (Max. units)

6 . OVERVIEW OF SSAS The IC-07 SSAS (Ship Security Alert System) Alert Unit connects to the Inmarsat-C MES FELCOM or the Inmarsat Mini-C FELCOM for the purpose of alerting specified addresses (for example, your ship s company) that your ship is under attack by intruders. The SOLAS Resolution XI-/ requires vessels of 00 GT or more constructed before 0 July 00 to install an SSAS. When your ship is under attack an SSAS report, which contains your ship s name, MMSI No., position, etc. is sent to up to five locations, specified by the ship s captain or authorized personnel. No audible or visible alarm is generated while the SSAS report is being transmitted, to prevent discovery of the report by the intruders. The SSAS is protected with a password to prevent unauthorized setting or testing of it by other than the ship s captain or authorized personnel. Inmarsat System Ship Name, MMSI No., Ship Position, etc. Ship Headquarters Ship s Company, Management Company

7 SSAS operation flow. Open the cover of the button and then press the button. (This is a latch-type button; hit and release to activate the button.). If addresses have been preset, the SSAS report is sent to one address 0 seconds after the button is activated. (Max. addresses) (You may cancel transmission of the SSAS report by pressing the button again within 0 seconds of the initial press.). An LES sends acknowledgement to your ship.. Steps - and are repeated in case of multiple addressees.. Continuous transmission of the SSAS report begins. (The interval at which to transmit the SSAS report to each address can be specified. The SSAS report is continuously transmitted while the button is ON, at the interval selected.). To stop transmission, press the button again to deactivate it. (This is only possible in the SSAS manager mode. See paragraph..)

8 . INSTALLATION. Mounting.. Junction box (for FELCOM ) The junction box IC- is required when installing the SSAS on the FELCOM ; it is already installed on the FELCOM. Separate the junction box from a magnetic compass by the distances shown below to prevent deviation to a magnetic compass. Standard compass:.0 m Steering compass: 0.7 m. Remove four screws from the unit to separate the cover from the unit.. Fix the unit to the mounting location with four self-tapping screws (x, supplied).. Connect the cables appropriately referring to paragraph... 0 ±0. 70 ±0. Junction box IC- The junction box is connected to the communication unit with a meter cable, with D-sub connector (at the communication unit). Therefore, locate the junction box within two meters of the communication unit.

9 .. SSAS alert unit Separate the junction box from the SSAS alert unit by the distances shown below to prevent deviation to a magnetic compass. Standard compass: 0.70 m Steering compass: 0. m Locate the SSAS alert unit where it cannot be found by intruders. The location should be known only by ship s captain and authorized personnel. Bulkhead mounting. Remove four screws from the unit to separate the bottom chassis from the top cover.. Fix the unit to the mounting location with four self-tapping screws (supplied).. The cable can be lead in from the bottom or the rear panel. For rear panel entrance, change the clamp orientation as follows: a) Unfasten three screws to remove the cable clamp. b) Turn the clamp 90 degrees. c) Refasten the clamp with three screws unfastened at step a) to fix the clamp. Unfasten three screws. Clamp Rotate Fasten three screws.. Run the cable thru one of the cable entrances and connect it to terminal board. 7

10 . Attach the switch cover as shown below. Note that the cover may also be rotated 80 degrees. Press here and hold down for five seconds. Switch cover Flush mounting The optional flush mount kit OP-8 (Code No ) is required. Name Type Code No. Qty Remarks Fixture Pan head screw Mx Self-tapping screw x Cut out the mounting position referring to the outline drawings at the back of this manual.. Fix the unit to the fixture with four pan head screws (supplied).. Fasten the fixture with the unit to the mounting location with four self-tapping screws (supplied).. Attach switch cover as shown above. 8

11 . Wiring.. Junction box (for FELCOM ) Use the junction box IC- to connect the SSAS alert unit to the FELCOM. Unfasten four screws to remove the cover to connect cables to terminal board. For detailed wiring information see the interconnection diagram. For connection, use the JIS cable TTYCS- (or equivalent, see next page for sectional view of this cable) or the CO-SPEVV-SB-C 0.xP. When using the CO-SPEVV-SB-C 0.xP cable, replace the cable clamp with the cable clamp , supplied with the junction box. Communication Unit Cable clamp Terminal board Cover Cable clamp (top) Vcc TD/RD-A TD/RD-B TD-A(NAV) 7 TD-B(NAV) 8 RD-A(NAV) 9 RD-B(NAV) 0 DMC OUT-H DMC OUT-C DMC IN-H DMC IN-C DMC CTR Cable clamp (bottom) IC-0/0 Core 7 mm Procedure. Insert driver from direction.. Tilt slightly toward.. Insert cable core to. S0 Fold back braided shield onto sheath and fix by cable clamp. Note : Do not insert the cable too deeply, to prevent pinching the sheath. Note : Pull each cable slightly to confirm that they are in their holes securely. mm 90mm 7mm Junction box IC- 9

12 .. SSAS alert unit Three SSAS alert units can be connected in series to the Junction Box IC-. Use the terminals on the SSAS ALERT Board P09 commonly and two connector entrances. To differentiate between units in case of multiple unit installation, change jumper block settings as shown below, in accordance with how many units are installed. Jumper settings for two IC-07 Jumper settings for three IC-07 Jumper Unit No. unit* No. unit *: Default Jumper Unit No. unit* No. unit* No. unit JP No Yes setting JP No No Yes JP Yes No JP Yes Yes No No. unit: Unit with two cables connnected to it. No. unit: Unit with one cable connnected to it. No. and No. units: Units with two cables connnected to them. No. unit: Unit with one cable connnected to it. Two IC-07: No. Three IC-07: No. Two IC-07: No. Three IC-07: No. and No. P09 JP JP P09 JP JP Crimp-on lug to use : FV.-, red : Not used. : FV.-, red : FV.-, red : FV.-, red : Shield (FV-, blue) IC-07 IC-07 Cable Fabrication Clamp for cable CO-SPEVV-SB-C 0.xP Clamp for cable TTYCS- or equivalent Twist the shield. CO-SPEVV-SB-C 0.XP or TTYCS- Cut unused cables. φ =. mm mm 0 mm 0 mm Shield Conductor S = 0.7 mm φ =. mm Sectional view of cable TTYCS- Armor Sheath Wiring inside the SSAS alert unit 0

13 . Initial Settings Set up the SSAS as follows:. FELCOM : Press [F8], [F] to show the System Setup menu. FELCOM : Press [F8], [F] to show the System Setup menu.. Press [ ] to choose Command Window and then press the [Enter] key. RFCOPU *** [ Main Menu ]. Remote Box Setup. Internal GPS Setup Enter JOB No. : Command Window. Type furunoservice (without quotation marks) in the Enter JOB No. field and then press the [Enter] key. The prompt PASSWORD appears.. Enter password (see Service Manual) then press the [Enter] key. Then, the item Main Menu is displayed in reverse video.. Press [], [Enter], [], [Enter]. One of the following windows appears. [ DMC ]. SSAS. DMC. OFF E: Exit Enter No.: FELCOM [ SSAS ]. ON. OFF E: Exit Enter No.: FELCOM. Press [], [Enter]. This enables the SSAS functions. 7. Press the [Esc] key several times to close the menu. Note: Test the SSAS button and SSAS report for proper operation, referring to paragraphs. and., respectively.

14 . OPERATION. Operation Mode There are two menu operating modes: Normal mode: Menus other than SSAS-related menus are displayed. SSAS manager mode: The mode is activated by the password entered by the ship s captain or authorized personnel. The indication SSAS Manager Mode is shown flashing at the top of the screen when this mode is activated. All SSAS-related menus are available. Transmission of the SSAS report may be cancelled in this mode. The equipment starts up in the normal mode, regardless of the mode in use when the power is turned off... Changing the password The default password is ship security alert. Ship s captain or authorized personnel may change the password as follows:. FELCOM : Press [F8], [F] to show the System Setup menu. FELCOM : Press [F8], [F] to show the System Setup menu.. Press [ ] to choose Command Window and then press the [Enter] key. RFCOPU *** [ Main Menu ]. Remote Box Setup. Internal GPS Setup Enter JOB No. : Command Window. On the Enter JOB No. field, type ssas password (without quotation marks) and then press the [Enter] key. The prompt OLD PASSWORD appears.. Type your current password and then press the [Enter] key. The prompt NEW PASSWORD appears.. Enter new password, using at least six characters, and then press the [Enter] key. The prompt RETYPE NEW PASSWORD appears. Note: If less than six characters are entered for the password, the message Please use a longer password. appears. Enter a longer password.. Enter new password again and then press the [Enter] key. The message Password changed appears. 7. Press the [Esc] key several times to close the menu. Note: The SSAS manager mode cannot be unlocked without the proper password.

15 .. SSAS manager mode All SSAS-related settings are set in the SSAS manager mode. Do the following to access this mode.. FELCOM : Press [F8], [F] to show the System Setup menu. FELCOM : Press [F8], [F] to show the System Setup menu.. Press [ ] to choose Command Window and then press the [Enter] key. Command Window RFCOPU *** [ Main Menu ]. Remote Box Setup. Internal GPS Setup Enter JOB No. :. On the Enter JOB No. field, type ssas manager (without the quotation marks) and then press the [Enter] key.. Type password and then press the [Enter] key. The window below appears; you are now in the SSAS manager mode :7 (UTC) SSAS Manager Mode enabled. CAUTION <Press ESC key to continue>. Press the [Esc] key several times to close the menu. This enables the SSAS manager mode, which allows you to execute the procedure in paragraph..

16 . Setting SSAS Report Destination and Message Contents When the SSAS is activated, the SSAS report is sent according to the addresses (max. ) and message content set with SSAS Report SSAS Report on the SSAS Report menu. Note : The destination and message content of an SSAS report varies according to Administration. Therefore, set them as requested by ship s authorities. For information other than ship s name, MMSI no. and IMN no., set it manually with Other Inf. Note : The equipment must be in the SSAS manager mode to execute this procedure. See paragraph.... Press the [F] to open the Reports menu. Reports. Data Report. Message Report. Data Network ID. SSAS Report. Press the [] key to shown the SSAS Report menu. SSAS Report. SSAS Report. SSAS Report. SSAS Report. SSAS Report. SSAS Report. Message Contents. Press [], [], [], [] or [] key as appropriate. (When the button is tested, a test report is sent to the address specified for the youngest SSAS report number. Therefore, set the address which is to receive the test report set for the youngest SSAS report number.) SSAS Report Status Station Name Destination Type Prefix Code Country/Ocean Code Station ID Modem Type Address Subject LES ID Report Interval ON TELEX 0:00 (hh: mm). Press the [ ] key to choose Station Name and then press the [Enter] key.. Press the [ ] or [ ] key to choose appropriate station and then press the [Enter] key. You may sort the list by group name, station name or communication type as follows: Group name: Each press of [Ctrl] + [G] sorts the list by group name, ascending or descending order. Station name: Each press of [Ctrl] + [N] sorts the list by station name, in ascending or descending order. Comm. type: Each press of [Ctrl] + [T] sorts the list by communication type, in ascending or descending order.

17 . Press the [ ] key to choose LES ID and then press the [Enter] key. 7. Press the [ ] or [ ] key to choose LES and then press the [Enter] key. 8. Press the [ ] key to choose Report Interval and then press the [Enter] key. 9. Enter time interval (00:0-99:9) to transmit the SSAS report and then press the [Enter] key. Note: After the SSAS report is transmitted and the button remains ON ( ), the SSAS report is transmitted at the interval set here. 0. Press the [Esc] key to open the Update window. Status Station Name Destination Type Prefix Code Country/Ocean Code Station ID Modem Type Address Subject LES ID Report Interval SSAS Report ON TELEX 0:00 (hh: mm) Yes Update No. Yes is selected; press the [Enter] key to close the SSAS report window.. Press the [] key to display the SSAS Message Contents menu. Vessel Name : MMSI : IMN : Other Inf. : LAT: LON: Time: COURSE: SPEED: Time: SSAS Message Contents _ :. N :. E 0/0/00 0::8 (UTC) 07 deg 00 kt 0/0/00 0::8 (UTC). Press the [Enter] key to open the Vessel Name window.. Enter vessel s name and then press the [Enter] key.. Press the [ ] key to choose MMSI and then press the [Enter] key.. Enter MMSI number and then press the [Enter] key. 7. Press the [ ] key to choose IMN and then press the [Enter] key. 8. Enter IMN and then press the [Enter] key. 9. Press the [ ] key to choose Other Inf. and then press the [Enter] key 0. Enter appropriate message (three lines) and then press the [Enter] key. Note: To shift between lines, use the [ ] or [ ] key.. Press the [Esc] key to display the Update window.. Yes is selected; press the [Enter] key to close the SSAS Message Contents menu.

18 . Press the [Esc] key twice to return to the standby display. Note : To delete entered subscriber s data, choose Remove from Status. Note : SSAS report settings may be saved to a floppy disk for backup. FELCOM : [F8], [9], [] to show the Save/Load window. FELCOM : [F8], [8], [] to show the Save/Load window. Save to FD. ALL. Station List. LES List. Service List. SSAS Report*. Other Load from FD. ALL. Station List. LES List. Service List. SSAS Report*. Other *: Availlable only in SSAS manager mode (".SSAS Report" is added in the SSAS manager mode and item numbers are shifted.) Note : To confirm the settings, follow paragraph..

19 . Transmitting SSAS Report In the normal mode, the SSAS report is sent 0 seconds after the button on the SSAS is pressed. The SSAS repeatedly transmits the report even if the button is pushed off ( ). Repeated transmission can only be stopped from the SSAS manager mode.. Open the cover of the SSAS alert button. Cover. Push the button. The button is a latch-type button; hit and release the button to activate ( ) the SSAS unit.. The SSAS report is transmitted 0 seconds after the button is pushed in ( ). Below are the contents of the SSAS report SSAS ALERT MESSAGE Vessel Name: Queen Elizabeth MMSI: 0000 IMN: Help me! LAT: :.N LON: :.E Time: 0/0/00 0::8 (UTC) COURSE: 07 deg SPEED: 00 kt Time: 0/0/00 0::8 (UTC) Ship s Name MMSI No. IMN No. Desired message Own ship postion in latitude Own ship position in longitude Time of position data Course Speed Time of course and speed data Note: If you accidentally push the button in, push it again within 0 seconds to cancel the report. The button pops out ( ) and the report is not transmitted. When this is done, the message INF: SSAS UNIT activation has been canceled. appears on the display. Additionally, for the FELCOM, the POWER lamp on the communication unit flashes 0 seconds.. An LES sends acknowledgement to your ship.. For multiple destinations, steps and are repeated.. The SSAS report is transmitted repeatedly while the button remains pushed in ( ). 7. To stop transmission, push the button again to pop it out ( ). (SSAS manager mode only.) 7

20 Note : You may cancel repeated transmission from either operating mode by pushing the button OFF ON OFF ON OFF. You must allow no more than three seconds to elapse before pushing the button again. If more than three seconds elapses, repeat the procedure. When transmission is stopped, the message INF: SSAS UNIT activation has been cancelled. appears and, on the FELCOM only, the POWER lamp on the communication unit flashes approx. 0 seconds. Note : If transmission is not canceled with the button and the power is turned off, the equipment resumes repeated transmission when powered again. 8

21 . Testing the Button The SSAS buttons can be tested as below. Note : An actual SSAS report cannot be transmitted during the testing. Note : The equipment must be in the SSAS manager mode to conduct the test. FELCOM. Press the [F7] key to display the Options menu.. Press the [7] key ([] key when the FELCOM functions as an EGC receiver) to display the Test menu.. Press the [] key. Test. PV Test. PV Test Result. Diagnostic Test. Distress/SSAS Button Test Options. Login.. Logout PV Test Test Distress/SSAS Button Test.. Abort PV Test Result.. Select Self Test S Start.. Ocean Distress Region Alarm Button Test. Test Yes No. Press the [Enter] key to start the test. Options. Login Test.. Logout PV Test Distress/SSAS Button Test.. Abort PV Test Result.. Select Self Distress/SSAS Test S buttons are under test mode... Ocean Distress Region Alarm Press Button any key Test CAUTION to escape. INF: Distress/SSAS. Test Buttons entered into TEST MODE. <Press ESC key to continue> The display shows the message (in red) Distress/SSAS buttons are under test. Cancel the test mode if a real distress/ssas needs to sent. appears.. Open the button cover on the No. SSAS.. Push the button in ( ). The CAUTION window displays the message SSAS UNIT works correctly. appears if the unit is functioning properly. Note: 0 seconds after step, the SSAS test report is automatically sent. If you do not need to send the SSAS report, go to step 8 within 0 seconds. 7. The SSAS test report is automatically sent once to the address specified for the youngest SSAS report number (-). 8. Turn the button of the No. SSAS off ( ). Note: To test the No. and No. SSAS repeat steps -8. 9

22 9. To escape from the test, press the [Esc] key twice on the terminal unit. The test mode is stopped and the message shown below appears to notify you that normal operation has been restored. CAUTION INF: Distress/SSAS Buttons returned to NORMAL OPERATION. <Press ESC key to continue> Further, because the button remains pushed in ( ), the message Please return the SSAS button into OFF-STATE. appears. 0. Push the button again to pop it out ( ).. Close the button cover.. Press the [Esc] key three times to return to the standby display. Note: If the button is left pushed in ( ) when the terminal unit is turned on, the equipment displays Please return the SSAS button into OFF-STATE. Push the button again to turn off ( ) the button. FELCOM (no PC). Turn off the communication unit.. Push the button of the No. SSAS to turn it on ( ).. Turn on the communication unit.. 0 seconds later the POWER, LOGIN and TX LEDs on the communication unit start flashing together if the button is judged to be ON. Note: An SSAS test report is automatically transmitted 0 seconds after all LEDs start flashing at step. If you do not need to send the test report, skip to step seconds after LEDs start flashing the SSAS test report is sent once to the address specified for the youngest SSAS report number (-). At this time the LEDs flash rapidly. If transmission was successful the LEDs mentioned in step flash slowly. If transmission failed, only the ERROR LED flashes (rapidly).. Push the button of the No. SSAS to turn it off ( ). The LEDs light in order of POWER, LOGIN, TX, POWER, LOGIN, TX. 7. Push the button of the No. SSAS to turn it on ( ) seconds later the POWER, LOGIN and TX LEDs on the communication unit start flashing together if the button is judged to be ON. Note: An SSAS test report is automatically transmitted 0 seconds after all LEDs start flashing. If you do not need to send the test report, skip to step seconds after the above-mentioned LEDs start flashing the SSAS test report is sent. 0. Push the button of the No. SSAS to turn it off ( ). Note: If there is a No. SSAS, test it by following steps Finally, turn the communication unit off and then on again. Note : After completing the testing, be sure to turn off all SSAS units. Note : The normal mode is automatically restored after 0 minutes elapses in the test mode. 0

23 Note : The ERROR LED flashes every two seconds if the button of an SSAS stays on for more than 0 seconds. It also flashes when the equipment switches to the normal mode (see Note ). Turn off the button to stop the LED from flashing. FELCOM (by PC). Press the [F7] key to display the Options menu.. Press the [7] key ([] key when the FELCOM functions as an EGC receiver) to display the Test menu. Test. PV Test. PV Test Result. Diagnostic Test. SSAS Button Test. Press the [] key. Options. Login Test.. Logout PV Test SSAS Button Test.. Abort PV Test Result.. Select Self Test S.. Ocean Distress Region Alarm Button Test. Test Yes Start No. Press the [Enter] key to start the test. Options. Login Test.. Logout PV Test SSAS Button Test.. Abort PV Test Result.. Select Self Test S SSAS buttons are under test mode... Ocean Distress Region Alarm Press Button any key Test CAUTION to escape. INF: SSAS. Buttons Test entered into TEST MODE. <Press ESC key to continue> The display shows the message (in red) SSAS buttons are under test. Cancel the test mode if a real SSAS alert needs to sent. appears.. Open the button cover on the No. SSAS.. Push the button in (ON). The CAUTION window displays the message SSAS UNIT works correctly. appears if the unit is functioning properly. Note: 0 seconds after step, the SSAS test report is automatically sent. If you do not need to send the test report, go to step 8 within 0 seconds. 7. The SSAS test report is automatically sent once to the address specified for the youngest SSAS report number (-). 8. Turn the button of the No. SSAS off ( ). Note: To test the No. and No. SSAS repeat steps -8.

24 9. To escape from the test, press the [Esc] key twice on the terminal unit. The test mode is stopped and the message shown below appears to notify you that normal operation has been restored. CAUTION INF: SSAS Buttons returned to NORMAL OPERATION. <Press ESC key to continue> Further, because the button remains pushed in ( ), the message Please return the SSAS button into OFF-STATE. appears. 0. Push the button again to pop it out ( ).. Close the button cover.. Press the [Esc] key three times to return to the standby display. Note: If the button is left pushed in ( ) when the communication unit is turned on, the equipment will go into the test mode if the SSAS is not transmitting repeatedly. To return to the standby display, push the button again to pop it out ( ) and then turn the communication unit off and on again.

25 . SSAS Report Test You can test for successful transmission of the SSAS report to the address you specify, without using the button. The test report message states!!! Test Call!!! to alert the receiver of the message that it is a test call.. Press the [F] key to open the Reports menu.. Press the [] key to choose the SSAS Report menu.. Press the [], [], [], [] or [] key as appropriate, and the SSAS report setting menu appears.. Set destination where to transmit the test.. Press the [ ] key to choose Status and then press the [Enter] key.. Press the [ ] key to choose TEST and then press the [Enter] key. 7. Press the [Esc] key to show the Update window. 8. Yes is selected; press the [Enter] key. The test report is transmitted. After it is transmitted, Status is automatically set to ON. 9. Press the [Esc] key twice to return to the standby display.

26

27

28

29 A B C D VDC - VDC 00-/ 0-0 VAC φ,0/0hz VDC RW-77 0.m アンテナユニット ANTENNA UNIT IC- 船 内 LAN (HUB) パソコンなど LAN(HUB) OR PC, ETC. VCTF-0.7xC m,φ.9 (S008) * DPYC-. φ.8 * DPYC- φ.9 TPAFB0.NJ FBA-DFB,0.m キーボード KEYBOARD BTC-00C PS/ VDC RHBPG-S J アカ RED +V クロ BLK シロ WHT 0V + - MJ-ASPF008,m,φ AC_IN VDC INPUT ケーブル:コネクタ 選 択 CABLE: CONNECTOR, SELECTED D-SFA-CV,00m,φ.: N-P-0DSFA 8D-FB-CV,0m,φ.0: N-P-8DFB TPFBAW-DFBB,0m,φ7. * Ethernet CABLE PC: CROSS CABLE HUB: STRAIGHT CABLE プリンタ PRINTER PP-0 VDC + * OUTPUT - PR-0-CE AC/DC 電 源 ユニット AC/DC POWER SUPPLY UNIT PE,IV-.SQ. 保 護 アース 注 記 *) 工 場 にて 取 付 済 み *) 造 船 所 手 配 *)オプション *)コネクタクランプでアースに 落 とす *)ユーザー 手 配 *)TB 基 板 (P0)が 必 要 *7) 台 または 台 接 続 可 能 終 端 のIC-07はジャンパー 設 定 の 変 更 が 必 要 * * 7-0 * TP-NJ RJ- P P 7JE-0-0(D8C) * S08,m,φ8 FUSE A(V) 7A(V) シロ WHT クロ BLK * MJ-ASPFD 7 8 ANT B0 KEYBOARD KDAT +V KCLK LAN E_TD_P E_TD-N E_RD_P E_RD_N PRINTER B0 ターミナルユニット TERMINAL UNIT IC- P008A P009 -VDC DC(+) DC(-) B0 P0 DGPS JUTION Vcc(ALM) TD/RD-A TD/RD-B TD-A TD-B RD-A RD-B DMC_OUT-H DMC_OUT-C DMC_CHECK DMC_IN-C DMC_CTRL DTE D-sub9P * D-sub9P 7JE-7-0,m,φ8 CO-0.xP,m MAX. TXD RXD CO-0.xP * 9 * m MAX. * 銅 板 W=0 COPPER STRAP ,.m B PLAG D-subP * * CO-AX (0Ω) S0,m,φ9. チャ BRN ミドリ GRN アカ RED ハイ GRY ダイ ORG アオ BLU キ YEL クロ BLK モモ PNK アオ/アカ BLU/RED シロ WHT タ イ/シロ ORG/WHT ミト リ/シロ GRN/WHT ムラサキ PPL FM-P DGPSデコーダー DGPS DECODER RXD TXD 0V I/F BOX OP- * 接 続 箱 JUTION BOX IC DMC_OUT-H DMC_OUT-C DMC_IN-H DMC_IN-C DMC_CTR CO-0.xP パソコン RXD TXD PC * DTR S. DSR RTS CTS * FM-7P CO-0.xP MAX.00m 7 * TTYCS-,φ. 航 法 装 置 NAV EQUIPMENT TXD-H TXD-C * TTYCS-,φ. OR CO-0.xP 合 計 : 最 大 00m TOTAL:MAX.00m * TTYCS-,φ. FM-7P FM-7P P P 7 7 P EGCプリンタ RXD EGC PRINTER TXD PP-0 0V * (+) (-) RXD-H TXD-H FG TXD-C RXD-C +9V P P P P P P P アラームユニットIC-0 ALARM UNIT 保 安 警 報 発 呼 器 SSAS ALERT UNIT IC-07 (No.) EGCプリンタ EGC PRINTER PP-0 * * (+) (-) P0B VCC TD/RD-A TD/RD-B FG 遭 難 警 報 器 IC-0 DISTRESS ALERT/ RECEIVED CALL UNIT P0A VCC TD/RD-A TD/RD-B FG TB IC-07 (No.) * *7 TB * *7 SSAS_OUT-H SSAS_OUT-H SSAS_CHECK SSAS_CHECK SSAS_IN-C SSAS_CTRL SSAS_IN-C SSAS_CTRL 遭 難 警 報 装 置 DMC- DISTRESS MESSAGE CONTROLLER TB DIST_IN-H DIST_IN-C DIST_OUT-H DIST_OUT-C DIST_CTR 08S07,m 08S S07,m 08S0087 保 安 警 報 発 呼 器 SSAS ALERT UNIT VDC VDC 保 安 警 報 発 呼 器 SSAS ALERT UNIT IC-07 (No.) TB * *7 SSAS_OUT-H SSAS_CHECK SSAS_IN-C SSAS_CTRL NOTE *. FITTED AT FACTORY. *. SHIPYARD SUPPLY. *. OPTION. *. GROUND THRU CONNECTOR CLAMP. *. USER SUPPLY. *. TB BOARD (P0) REQUIRED. *7. OR SETS CAN BE CONNECTED. CHANGE JUMPER SETTING IN LAST IC-07. CO-0.xP: CO-SPEVV-SB-C 0.xP,φ0. CO-0.xP: CO-SPEVV-SB-C 0.xP,φ. DRAWN Apr. '0 CHECKED K.MIYAZAWA TAKAHASHI.T APPROVED SCALE MASS kg DWG No. C-C0- E TITLE 名 称 FELCOM インマルサットC 船 舶 地 球 局 相 互 結 線 図 NAME INMARSAT-C MES INTERCONNECTION DIAGRAM FURUNO ELECTRIC CO., LTD.

30 A B C アンテナユニット ANTENNA UNIT IC- RW m TPAFB0.NJ FBA-DFB,0.m ケーブル:コネクタ 選 択 CABLE: CONNECTOR, SELECTED D-SFA-CV,00m,φ.: N-P-0DSFA 8D-FB-CV,0m,φ.0: N-P-8DFB TPFBAW-DFBB,0m,φ7. TP8AW-RG8,m,φ.0 - VDC P--.(P),.m,φ7. アカ RED クロ BLK * FM-CFP 00-/ 0-0 VAC φ,0/0hz VDC * DPYC-. φ.8 * DPYC- φ AC_IN VDC INPUT VDC OUTPUT * PR-0-CE AC/DC 電 源 ユニット AC/DC POWER SUPPLY UNIT + - 注 記 *) 工 場 にて 取 付 済 み *) 造 船 所 手 配 *)オプション *)コネクタクランプでアースに 落 とす *)ユーザー 手 配 *)SSAS 仕 様 *7) 最 大 台 まで 接 続 可 能 終 端 のIC-07はジャンパー 設 定 の 変 更 が 必 要 NOTE *. FITTED AT FACTORY. *. SHIPYARD SUPPLY. *. OPTION. *. GROUND THRU CONNECTOR CLAMP. *. USER SUPPLY. *. SSAS SPECIFICATION. *7. MAX SETS CAN BE CONNECTED. CHANGE JUMPER SETTING IN LAST IC-07. PE,IV-.SQ. 保 護 アース ANT -VDC DC(+) DC(-) DRAWN Apr. '0 CHECKED APPROVED SCALE DWG No. K.MIYAZAWA TAKAHASHI.T MASS C8-C0- D kg TITLE 名 称 NAME FELCOM インマルサットC 船 舶 地 球 局 相 互 結 線 図 INMARSAT-C MES INTERCONNECTION DIAGRAM TP-NJ FUSE V:0A V : A 通 信 制 御 ユニット COMMUNICATION UNIT IC- B0 P008B DTE TXD RXD D-sub9P 7JE-7-0,m,φ8 * D-sub9P * * パソコン PC * RXD TXD DTR S. DSR RTS CTS B0 P07 SSAS Vcc(.V) TX/RX-A TX/RX-B SSAS_OUT-H SSAS_CHECK SSAS_IN-C SSAS_CTRL D-subP * チャ ミドリ アカ ハイ ダイ アオ キ クロ モモ アオ/アカ シロ タ イ/シロ ミト リ/シロ ムラサキ S0 m,φ9. BRN GRN RED GRY ORG BLU YEL BLK PNK BLU/RED WHT ORG/WHT GRN/WHT PPL * 接 続 箱 JUTION BOX IC- * Vcc TD/RD-A TD/RD-B TD-A TD-B RD-A RD-B DMC_OUT-H DMC_OUT-C DMC_IN-H DMC_IN-C DMC_CTR P P 保 安 警 報 発 呼 器 SSAS ALERT UNIT IC-07 (No.) TB * SSAS_OUT-H SSAS_CHECK SSAS_IN-C SSAS_CTRL 保 安 警 報 発 呼 器 SSAS ALERT UNIT IC-07 (No.) TB * SSAS_OUT-H SSAS_CHECK SSAS_IN-C SSAS_CTRL W=0 銅 板 COPPER STRAP ,.m * * TTYCS-,φ. OR CO-0.xP 全 長 00m 以 下 TOTAL:00m MAX. 保 安 警 報 発 呼 器 SSAS ALERT UNIT IC-07 (No.) TB * * *7 SSAS_OUT-H SSAS_CHECK SSAS_IN-C SSAS_CTRL