Please make sure you install GSU and after GKU software befor you plug the Glitch360Shark to your computer!

Transcription

1 GLITCH360SHARK INSTALLATION MANUAL v1.9 FOR XBOX 360 SLIM This Manual will explain you how to install the Glitch360Shark on your xbox 360 SLIM. For more information about the Reset Glitch Hack check our webpage STEP 1: Required Tools - Glitch360Shark v1.1 - Quick Connector 11x wire - 1x Glitch360Shark USB 2.0 PCB - 1x Addon Shark (optional) - 1x Pressure Pad - 1x Micro double side tape - Soldering iron 12/15w + soldering tin And of course one xbox with a Glitch Modchip installed (ex: Glitch360Key) Please make sure you install GSU and after GKU software befor you plug the Glitch360Shark to your computer! Note : On windows 7 the drivers should install alone but on windows XP you will have a popup (new device detected), just click Next as many times until the drivers are installed. The Glitch360Shark is easy and quick even so take the time to read the following instructions. Wires install: 1 > J2C37 / 2 > J2C312 / 3 > J2C13 / 4 > J2C11 / 5 > J2C14 / 6 > J2C12 / 7 > J2C36 / 8 > J2C35 / 9 > U4E2-3 / 10 > C3T12 / 11 > UCC33 (3.3v of your Glitch Modchip)

2 STEP 2a: Quick Connector install on Trinity Motherboard STEP 2b: Quick Connector install on Corona Motherboard

3 Connect the Glitch360Shark to your Glitch Modchip Note : Solder the wire #11 on the VCC (3,3v) of your Glitch Modchip (Exemple : UC33 on the Glitch360Key) The 3.3v from the Motherboard to the Modchip must not be soldered. Connect the Glitch360Shark to your Glitch360Key Ultra Note : Solder the wire #11 on CMD of the Glitch360Key Ultra and solder the 3.3v from the Motherboard to the Modchip.

4 Step 3: Glitch360Shark USB 2.0 PCB Note: Lift out the xbox 360 motherboard in order to pass the USB 2.0 wire thru the USB hole behind your xbox 360 Note: Use the sticker under the USB 2.0 PCB and the PCB behind you xbox 360 Once you have soldered all the 11x wires, installed the USB 2.0 pcb and your Glitch Modchip, Please screw your motherboard back in the metal case befor going to the next step!

5 STEP 4: Cleaning the Motherboard Nand Note: Clean the motherboard nand pins with 90 alcohol, make sure there is no dust or anything else on the pins. It is also recommended to clean the pins of the Glitch360Shark NandClip Wait until the alcohol driesd off. The Nand pins are most of the time very dirty, even if they are shiny it is VERY important to clean them so that the Nandclip connect correctly with your motherboard Nand!

6 STEP 5: Connect the 2 Quick Connector to your Glitch360Shark Note: Plug Firmly both USB 2.0 and 11x wire Quick Connector to the Glitch360Shark, make sure they are correctly plugged

7 STEP 6: Clip the Glitch360Shark on your Motherboard Nand Warning: Remember to take off the red protection on the pad under the Glitch360Shark Note: To do this right you have to start by plugging the right side of the NandClip (top of the picture) then press in the left side (down on the picture) firmly. Now push firmly on the nand of the Glitch360Shark so that the NandClip will clip correctly on your motherboard nand. Your Glitch360Shark is now clipped on the motherboard Nand! It s as simple as that! Once the Glitch360Shark is connected CORRECTLY on your Motherboard nand DO NOT TRY TO UNCLIP

8 Once your Glitch360Shark is correctly connected, stick the PadStab v2 using a double sided sticker on the nand of the Glitch360Shark

9 STEP 7: The Addon Shark (optional) Note: This optional addon was made to easily and simply connect your Glitch360Key to the Glitch360Shark in order to fully control it. The AddonShark also allows you to program and update your Glitch360Key anytime using our Software (GKU) without having to open your xbox 360! To program your Glitch360Key make sure you switch to «Shark Mode» by pressing once on the Synch button next to the USB hatch on the front pannel of your xbox 360 slim. (see TROUBLESHOOTING) How to program your Glitch360Key using the AddonShark Glitch? Plug your xbox 360 to your computer using the USB 2.0 PCB (step 3). Install our software GKU (download GKU.exe). Make sure GSU is closed while you use GKU! To Program your Glitch360key simply choose your type of xbox 360 then select your motherboard, Click «Enable Dual Nand Feature» and click FLASH/UPDATE. Classic Mode Expert Mode

10 STEP 8 : Check that your Glitch360Shark is installed right How do I know if my Glitch360Shark is correctly «CLIPED»? The NandClip must completly cover your Nand and it should almost touch themotherboard (see picture) How do I know if my Glitch360Shark is correctly installed? Once you have completly installed your Glitch360Shark, put de metal conver on your xbox 360 and screw on the 5 long black screws. Plug the power bloc and turn on your xbox 360 in «Shark Mode» by pressing once on the «Sync» button then press the power: A The Xbox 360 does not boot : This is normal, your secondery nand is empty. Your Glitch360Shark should be connected right. Connect your Glitch360Shark to your computer and move to Step 9. B The Xbox 360 boots! : Your Glitch360Shark is not cliped right. Go back to Step 6 and make sure everything is done correctly.

11 STEP 9 : Program your Glitch360Shark using GSU

12 Once your have finished the programming of your Glitch360Shark you must unplug the xbox power at least 10sec befor you turn it on. - TROUBLESHOOTING (to be updated ) How do I switch my xbox 360 from Retail Mode to Shark Mode? Simply press the «Sync» button found on the front pannel of your Xbox 360 (see picture) while it s powered off, the crystal blue light will turn on letting you know you are on «Shark Mode». Press again the «Sync» button and you will go back to «Retail Mode» (the blue light will turn off) After chosing the Retail or Shark Mode, just press the power button to turn on your Xbox 360

13 Copyrights GlitchTeam V1.9 Glitch360Shark Dual Nand Easy Clip Seb117, ZackWarrior, Elyot Made in FRANCE