Quick Installation Guide Simple integrated version of manuals for installation and programming

Transcription

1 Version 1.0 ipldk-60 Quick Installation Guide Simple integrated version of manuals for installation and programming Step 1 Hardware Installation Step 2 Basic

2 Contents Getting Started Overview 1.Overall Installation Procedure 2.Understanding ipldk-60 Hardware Step 1) Hardware Installation 1.Installing the Hardware Step 2) Basic 2-1) Initializing hardware configuration automatically 2-2) Installing PC-Admin Program and connecting PC to the system 2-3) Describing the basic menu trees of PC-ADMIN Program 2-4) Setting the nation code as Brazil 2-5) Understanding the default configuration 2-6) Performing the basic programming on the key items 2-6-1) Numbering Plan - change the station number if requested 2-6-2) CO Ring Assignment Assigning which CO line incoming calls go to which station(s) 2-6-3) CO Group Access Station Assigning which stations use which CO lines 2-6-4) Change the default values for the most frequently requested features. - COS(call restriction setting) - Flexible button assignment for digital/ip telephones - Registering system speed dial list - MOH(Music on Hold) - Doorphone installation - Date/Time change of the system Step 3) Advanced 3-1) DB upload / download (Page 36) 3-2) Software upgrade 3-3) E1R2 3-4) PRI 3-5) Hunt Group UCD 3-6) Installing VOIB board 3-7) IP Extension Phontage 3-8) IP Extension IP Phone 3-9) SIP Trunks 3-10) Off-line PC-Admin 3-11) LCR 3-12) CCR Appendix A. Customer Requirements Check-list B. Documentation Reference Guide C. Terminal User Guide Digital / IP terminals Analog telephones D. ipldk-60 IP Network configuration guide LG-Nortel Confidential Information

3 Getting Started This Quick Installation Guide provides the key steps to install and configure ipldk-60 system. This guide is a light & integrated version of hardware and programming manuals. Among hundreds of features supported in ipldk-60 systems, this guide provides the instructions to most frequently used features in small companies. This guide will help installers not only to understand ipldk-60 system easily but also help to learn the capability to install and program very quickly. This guide is composed of four parts as below. 1) Overview This section is to give the basic introduction to ipldk-60 system and the general description of the whole processes for installation and programming. 2) Step 1 : Hardware installation This section describes hardware components, functions of each parts and overall hardware installation procedures. 3) Step 2 : Basic Feature This step provides the fundamental items necessary to program. Basic software operation & programming instructions will be given in this step. 4) Step 3 : Advanced Feature This gives the programming guides for advanced features. This is an optional part necessary to program with specific customer requirements. Generally, Step 1 and 2 above cover most small customers typical requirements. For complicated programming to enable specific functions and features, the original manuals can be referred. In each section, the reference pages in manuals is provided. However, for beginners, it is recommended to fully understand this guide in advance. 3 LG-Nortel Confidential Information

4 Overview Hardware Installation Basic Feature Advanced Feature 1. Overall Installation Procedure This is the overall steps to install and administer ipldk-60 system. It will be very helpful to get this overall installation procedures in advance. Step1 Hardware Installation Step2 Basic Feature Step3 Advanced Feature Descriptions Key Hardware components Key Service Unit (System) CO & Extension Interface Board Optional Function Board (VOIU, VMIU, AAFU, etc) Terminals (Digital, IP, Analog) Accessories (Relay, Alarm, etc..) Basic Features Change Station numbers CO Ring Assignment CO Group Access Station Assign Basic Feature Settings Station/CO COS, Flexible buttons, MOH, Doorphone Advanced Features Database Up/Download Remote Software Upgrade E1R2, PRI UCD, LCR, CCR IP Extension, SIP Trunks Off-line PC-Admin 1.Check and Install necessary hardware components for Advanced Features (CCR-VMIU, IP-VOIU, etc) 2.Start PC-Admin 3.Program advanced features as instructed. Installation 1.Unpack and check hardware components (12p) 2.Open front cover of KSU (14p) 3.CO & Extension Board / Option Board connection (38p/49p) 4.ipLDK-60 System Mounting (19p) 5.MBU, EMBU connection (24p) 6.Grounding KSU (17p) 7.Backup Battery installation (18p) 8.PSTN/E1/PRI cabling ( ) 9.Terminals cabling (51p) 10.Accessories cabling 1.Install PC-Admin onto PC 2.Connect PC to System 3.Start PC-Admin 4.IP setting (System, PC-Admin) 5.Program major features as instructed. Declined lettering : Optional steps 4 LG-Nortel Confidential Information

5 Overview Hardware Installation Basic Feature Advanced Feature 2.Understanding ipldk-60 Hardware ipldk-60 hardware is composed of 3 categories. This part will give the overall list and brief description. The following figure shows the devices which connect to the ipldk-60 system. System Connection Diagram 3 Categories : 1. Main system - Basic system (BKSU) - Expansion system (EKSU) 2. Optional CO/Extension Interface Boards 3. Terminals - Digital telephones - IP telephones - Analog telephones - Accessories (MOH, Alarm, etc..) 5 LG-Nortel Confidential Information

6 Overview Hardware Installation Basic Feature Advanced Feature 2.Understanding ipldk-60 Hardware Category Items Board Brief description 1.Main System 1) BKSU (Basic KSU) MBU This is the basic system of ipldk-60 that has the main system software running on CPU. (MBU is the mother board of basic system) This has basic CO/Extension interfaces and can be expanded with optional interface boards. (Basic 3 CO line, 1 DKT & 7 Hybrid Interface) Option slots one for capacity expansion, a MODU slot, VMIU/AAFU slot, VOIU Slot and CMU slot 2) EKSU (Expansion KSU) EMBU This is the expansion system of ipldk-60 for capacity expansion. This is controlled by main system software of BKSU and only provides additional CO & extension interfaces. (EMBU is the mother board of expansion system no CPU) This has basic CO/Extension interfaces and can be expanded with option interface boards. (Basic 3 CO line, 8 Hybrid Interface) Option slots one for capacity expansion, CMU slot PSU BKSU and EKSU has its own power supply unit respectively. 100~240 +/- 10% Volt AC 90W 2.Optional CO and Extension Interface Boards CHB308 (NTB417) CSB316 (NTB418) SLIB8 (NTB416) 3 CO Lines and 8 Hybrid Interface Board 3 CO Lines and 16 SLT Interface Board 8 SLT Interface Board E1HB8 (NTB419) E1R2 and 8 Hybrid Interface Board PRHB8 PRI and 8 Hybrid Interface Board VOIB (NTB422) 6 LG-Nortel Confidential Information Voice over IP Interface Board (4 Channels).Dual stacks of H.323 Revision4 and SIP Protocol The channel can be expanded to 8 channels with optional VOIU unit.

7 Overview Hardware Installation Basic Feature Advanced Feature 2.Understanding ipldk-60 Hardware Category Items Board Brief Description 2.Optional CO and Extension Interface Boards 3.Terminals VMIU (NTB420) AAFU (NTB421) MODU (NTB413) CMU50PR (NTB415) CMU12PR (NTB414) LDP-6212D (NTB424, NTB426) LDP-6230D (NTB425, NTB427) LIP-6012D (NTB433AA ) LIP-6030D (NTB434AA) LDP-6248DSS (NTB428) LDP-DPB (NTB429) Voice Mail Interface Unit (4 channels) Max recording time : 123min (System greetings-24min, Users 99min) Max number of voice messages (800 ea) Auto Attendant Function Unit (4 channels) Max recording time : 33min (System greetings-24min, Users 9min) Max number of voice messages (800 ea) MODEM unit (33Kbps) This is an optional unit mounted on BKSU or EKSU (CN9/10) to detect the call metering signal for 50Hz and Polarity Reversal (3 channels) This is an optional unit mounted on BKSU or EKSU (CN9/10) to detect the call metering signal for 12KHz,16KHz or Polarity Reversal (3 channels) Digital Key Telephone.3Line LCD, 12 Flexible Button Display.Dark Black(NTB424), Light Grey(NTB426) Digital Key Telephone.3 Line LCD, 30 Flexible Button Display.Dark Black(NTB425) and Light Grey(NTB427) IP Telephone.3Line LCD, 12 Flexible Button Display IP Telephone.3 Line LCD, 30 Flexible Button Display 48 Button DSS Console Door Phone Box 7 LG-Nortel Confidential Information

8 Hardware Installation Basic Feature Advanced Feature Step 1 provides the steps to install hardware appropriately for each customer site. Based on customer requests, perform the installation as the following steps. 1-1) Unpack and check hardware components (Page 9) 1-2) Open front cover of KSU (Page 10) 1-3) Connect CO & Extension Board / Option Board if necessary. (optional) (Page 10) 1-4) ipldk-60 System Mounting (Page 11) 1-5) MBU, EMBU connection ((Page 12) 1-6) Backup Battery installation (Page 12) 1-7) Grounding KSU (Page 12) 1-8) PSTN/E1/PRI cabling (Page 13) 1-9) Terminals cabling (Page 13) 1-10) Accessories cabling (Page 13) 8 LG-Nortel Confidential Information

9 Hardware Installation Basic Feature Advanced Feature 1-1) Unpack and check hardware components Open the box and check the components shown in below figures. BKSU Components EKSU Components Basic Key Service Unit Mounting Plate Expansion Key Service Unit Mounting Plate CD manual Power cord Power cord Battery cable Jump wire Tie cable Battery cable Rubber feet Link cable Tie cable Rubber feet Anchor plug Screw Fuse Relay connector Anchor plug Screw Fuse Relay connector Cables and Accessories Cables and Accessories 9 LG-Nortel Confidential Information

10 Hardware Installation Basic Feature Advanced Feature 1-2) Open front cover of KSU 1-3) CO & Extension Board / Option Board connection Connect the necessary option boards at the right position described as in figure. If there is no option boards necessary, step 1-2 and 1-3 can be skipped. PRHB8 10 LG-Nortel Confidential Information

11 Hardware Installation Basic Feature Advanced Feature 1-4) ipldk-60 System mounting There are generally 3 ways to install the system like WALL Mounting, RACK Mounting, DESK Mounting. Select the proper place to install the system. WALL Mounting 19 RACK Mounting DESK Mounting Rubber Feet Anchor plug Screw 1.Attach mounting plate on the wall with anchors and screws 2.Hook the System to the screws on the wall with sliding-down 1.Attach the rack bracket to the bottom of the System 2.Affix the bracketed System onto 19 Rack with screws 1.Remove the backing paper of rubber feet 2.Attach the rubber feet to the bottom of the System 3.Mount the System on the Other 11 LG-Nortel Confidential Information

12 Hardware Installation Basic Feature Advanced Feature 1-5) MBU, EMBU connection This step is necessary to install both BKSU and EKSU. BKSU and EKSU can be connected via champ cable which is provided with EKSU system. This can be skipped only with BKSU installation. 1-6/7) Backup Batter installation and Grounding KSU BKSU/EKSU Linking Battery Connection and Frame Ground CAUTION The equipment should be connected to a socket-outlet with a protective ground connection It is recommended that the ground cable is shorter than 1m(3.28ft) It is recommended to use an external backup battery fuse between the battery and the System 12 LG-Nortel Confidential Information

13 Hardware Installation Basic Feature Advanced Feature 1-8/9/10) Cabling for PSTN/E1/PRI, Terminals cabling, Accessories cabling The MBU provides various interface for cabling of the different type of terminals. RJ45 is for internet connection, RJ11 is for CO or Station line connection and so on. Refer to the bellow tables and do cabling for your purpose. BKSU Interface 1 MBU CO (MJ1) MBU MJ1 1,2,3 2 TYPE PIN Number NO RJ11 1,2 N/A Signal Name 3,4 CO-T, CO-R 5,6 N/A E1 Port ( E1HB8 ONLY) TYPE Pin Number NO SIGNAL NAME RJ45 3,6,7,8 RESERVED 1 TX+ 2 TX- 4 RX- 5 RX MBU Extension(MJ2) MBU MJ2-1 (DKT ONLY) 3 4 TYPE PIN NUMBER NO SIGNAL NAME RJ11 1 N/A 2 DKT-T 3,4 ALARM_ Detection 5 DKT-R 6 N/A * MBU Extension (MJ2) 2,3,4,5,6,7,8 PIN TYPE NUMBER NO SIGNAL NAME RJ11 1 N/A 2 DKT-T 3,4 SLT-T, SLT-R 5 DKT-R 6 N/A * notes : 1) When installing DKT or SLT on Hybrid Ports, (MJ2-2,3,4,5,6,7,8), keep the above pin assignment. Otherwise the DKT or SLT will not operate normally. 2) Centered 2-wired cable is used for SLT connection, and 4-wired cable is used for DKT connection each. But in case of DKT, just 2 outer ones of 4 wires are used actually. 13 LG-Nortel Confidential Information

14 Hardware Installation Basic Feature Advanced Feature 1-8/9/10) Cabling for PSTN/E1/PRI, Terminals cabling, Accessories cabling The MBU provides various interface for cabling of the different type of terminals. RJ45 is for internet connection, RJ11 is for CO or Station line connection and so on. Refer to the bellow tables and do cabling for your purpose. BKSU Interface 1 MBU External Music Source(PJ1) 2 TYPE COLOR FUNCTION Audio Jack RED External Music Source MBU External Paging(PJ2) TYPE COLOR FUNCTION Audio Jack BLUE External Paging 3 Relay Contact Pin Assignment (CN13) 4 LAN (MJ3) Pin Assignment TYPE NO SIGNAL NAME 4 PIN 1 Relay 1-pin1 2 Relay 1-pin2 3 Relay 2-pin1 4 Relay 2-pin2 TYPE RJ45 Pin Number NO SIGNAL NAME 4,5,7,8 RESERVED 1 TX+ 2 TX- 3 RX- 6 RX+ 14 LG-Nortel Confidential Information

15 Basic Feature Advanced Feature Step 2 provides the procedures to configure the basic-level features of ipldk-60 system, which are mostly fundamental and typical in the real customer sites. Most steps in this section are necessary to be configured in order to get the most effective usage of the system. Detail settings may vary on site-by-site. 2-1) Initializing hardware configuration automatically (Page 16) 2-2) Installing PC-Admin Program and connecting PC to the system (Page 17) 2-3) Describing the basic menu trees of PC-ADMIN Program (Page 18) 2-4) Setting the nation code as Brazil (Page 19) 2-5) Understanding the default configuration (Page 20) 2-6) Performing the basic programming on the key items (Page 21) 2-6-1) Numbering Plan - change the station number if requested 2-6-2) CO Ring Assignment Assigning which CO line incoming calls go to which station(s) 2-6-3) CO Group Access Station Assigning which stations use which CO lines 2-6-4) Change the default values for the most frequently requested features. - COS(call restriction setting) - Flexible button assignment for digital/ip telephones - Registering system speed dial list - MOH(Music on Hold) - Doorphone installation - Date/Time change of the system 15 LG-Nortel Confidential Information

16 Basic Feature Advanced Feature 2-1) Initializing hardware configuration automatically ipldk-60 system software should be initialized at its first installation to properly read the hardware configuration. Get all the necessary interface boards assembled before power on. This initialization process applies only for the 1 st hardware configuration. If hardware add-on cases, different procedure should be followed. Refer to the Hardware Installation manual for the details. MBU on BKSU SW1 DIP 4 on *2) *4) SW1 DIP 4 off Procedure : 1) Complete all hardware installations and wiring. *2) Before system power on, check the SW1 DIP4 on at the MBU on BKSU. 3) Then, power on. System software automatically starts and processes the initialization which takes less than a minute. *4) Set the SW1 DIP4 off to protect from Database reinitialization after the initialization just in case of any types of system failure. This is the completion of this process. Now, system is ready to provide the default call services, which will be explained at the next page. Notes : System Database (DB) will be refreshed when it restarts in any reason with SW1 DIP4 on. It is necessary to check the hardware configuration to make sure that automatic initialization is properly performed. This can be checked at Pre-programmed/Configuration (PGM101~103). 16 LG-Nortel Confidential Information

17 Basic Feature Advanced Feature 2-2) Installing PC-Admin Program and connecting PC to the system There are two ways to do the programming of ipldk-60 system - 1) PC-ADMIN, 2) Keyset-ADMIN This guide will be primarily based on PC-ADMIN. For Keyset based ADMIN, please refer to the programming manual. 1), 2) 3)Direct LAN connection 1) Install PC-Admin S/W on your PC by running Setup.exe file of PC-Admin. Get the PC-Admin Setup file at PC Requirements : Pentium Celeron 233M or above, at least 64MB RAM, MS Windows NT/2000/XP 2) Set the IP Address of PC IP Setting on PC : x, Delete Gateway/Subnet field. Default IP of ipldk-60 : ) Connect PC and ipldk-60 (LAN port on MBU) via LAN directly 4) 4) Run the PC-Admin program on your PC. You will see the login pop-up window. Input ID/Password ID : Administrator P/W : ) Go to Tools/ Site management. Input Name and System IP. Default : and Save. Other fields are optional. 6) Position the mouse on the Site and click the right button. Click Connect(LAN) )Enter the connection password. (Default : no password Just Enter) You will see the main PC-Admin Window. Now you are ready to do the basic Admin LG-Nortel Confidential Information

18 Basic Feature Advanced Feature 2-3) Describing the basic menu trees of PC-ADMIN Program This describes the basic level of menu architecture of PC-Admin program. Even though sophisticated administrations can be performed with this program, for the beginners, it is strongly recommended to simply follow the instructions and fully understand this guide in advance. Later on, complex levels of programming can be learned through the programming manual. 6) 7) 8) 9) 10) 1) 2) 3) 5) * Refer to the PC-Admin user guide for the details. 4) 1) System software category (Office Version only available) 2) System Software Version with release time 3) PC-Admin Program Version with release time 4) Selected country and site name 5) menu tree. Each programming field can be accessed by double clicking 6) File Connect / Disconnect to the system 7) Tools Site Information for multi-site information management User Management, Level management Access authority to the programming menu in different level can be managed 8) Option Language can be selected either Local or English 9) LDK Utility LDK DB upload/download LDK Remote Diagnostic LDK Upgrade LDK Speed Editor Path LDK Speed Editor 10) Help at the last 18 LG-Nortel Confidential Information

19 Basic Feature Advanced Feature 2-4) Setting the nation code as Brazil It is necessary to set the system nation code as Brazil to load the default values for Brazil market as the first step. 1) 1) Select the nation as Brazil at Location information (PGM100). 2) Check SW1 DIP4 on and click update 2 3) Reset the system by pressing the reset button on MBU. Then all default configuration for Brazil will be loaded 4) Position SW1 DIP4 off after the system reboot LG-Nortel Confidential Information

20 Basic Feature Advanced Feature 2-5) Understanding the default configuration Once hardware installation(step1) and initialization(step2-1) are completed, ipldk-60 is ready to provide basic call services as followings based on the default configuration prior to any programming. From this default operation, it is necessary to do the planning of the programming for the customer site. It is recommended to use the customer requirement check-list (refer to Page 68) for effective planning. Default configuration & operation [308] Configuration [616] Configuration Default Numbering plan : 1) CO and station port numbers are assigned as in figures by default. CO number is assigned from left to right : CO1/2/3, CO4/5/6 at the upper Station number is assigned from left to right : 100~107, 108~115 at the upper STA2(101) is set as the system attendant. Default Call Operation : 1) Incoming calls from any CO lines go only to STA2(101). Then, STA2 can transfer the call to the other station as requested. 2) For outgoing calls, press 0 followed by the destination number. System will seize one of idle CO lines from CO1 to CO3 orderly by default for 308 basic case. There is no restriction pre assigned to make any type of calls like local, long distance, international. 3) For station to station internal calls, press the extension number directly. 4) These call services are the same for 24 hours, set as Day mode. Above default numbering plan & operation can be modified accordingly from the customer requests. These lists below can address most of typical requirements for small companies (Details are the Step 2-5) 1) Numbering Plan - change the station number if requested 2) CO Ring Assignment - which CO line incoming calls go to which station(s) 3) CO Group Access Station - which stations use which CO lines 4) Change the default value for the basic feature operation such as call restriction by station, MOH change, flexible button assignment for digital telephone and many more. These modifications depend on the customers demand. 20 LG-Nortel Confidential Information

21 Basic Feature Advanced Feature 2-6) Performing the basic programming on the key items This part gives the instructions to the basic programming on the typical items for small companies. As explained in Step 2-5), the followings are most frequently requested items for basic programming ) Numbering Plan - change the station number if requested 2-6-2) CO Ring Assignment Assign which CO line incoming calls go to which station(s) 2-6-3) CO Group Access Station Assign which stations use which CO lines 2-6-4) Change the parameters for the most frequently requested features. - COS(call restriction setting) - Flexible button assignment for digital/ip telephones - Registering system speed dial list - MOH(Music on Hold) - Doorphone installation - Date/Time change of the system The terms in Parenthesis above are used for ipldk-60 administration. Even though these terms are not general terms, it is important to understand the terms and concepts clearly. These are described in details in later-on sections. 21 LG-Nortel Confidential Information

22 Basic Feature Advanced Feature 2-6-1) Numbering Plan - change the Station Numbers and Feature Code if requested By default, the station number is set from 100~147 matched with the hardware port number as in the figure on the right. The station number can be changed by range or station by station. In addition to station number changes, there are several sets of feature codes available. Note that the station number should not be the same as the feature code numbers. For details, refer to the manual. 1)Change by range 2)Change station by station ) 2) 3) (station) 3) (Range) Station number change by station 1) Go to Pre-Programmed/Numbering Plan(PGM104~109) in the menu tree and double clicking. 2) Position the mouse at the station number to change and click the right button. Click again the Update Tool. 3) Put the new station number and click update station number Station number change by range 1) Go to Pre-Programmed/Numbering Plan(PGM104~109) in the menu tree and double clicking. 2) Position the mouse at the station number to change and click the right button. Click again the Update Tool. 3) Put the new station range and click update station number 22 LG-Nortel Confidential Information

23 Basic Feature Advanced Feature 2-6-2) CO Ring Assignment Assigning which CO line incoming calls go to which station(s) By default, all incoming CO calls are switched only to STA2(101). This default call routing only to station 101 can be modified generally in 3 ways as follows. - Incoming calls via specific CO line(s) can be programmed to go to a certain station or multi stations. - Incoming calls via specific CO line(s) can be programmed to go to a station group (Also called as Hunt Group.) - Incoming calls via specific CO line(s) can be programmed to go to DISA (This is for assigning AA(Auto attendant)) * If a CO line is assigned for DISA above, the system AA is activated. AA activation scenario will be explained in Step 3. ** These incoming call distribution could be differently programmed among 3 options above by time of day. Default mode is Day mode, which applies the same for 24hours. In this guide, the default operation mode will only be referenced. Therefore, any call distribution exampled here will be applied the same for 24 hours. Here, the following 2 typical cases will be guided with examples. (The 3rd DISA case will be explained at Step 3-12 CCR) 1 CO1 calls go only to DKT1(100) 2 CO2/3 calls go to a station group (101~107) - Next page with circular ringing -one station ringing at a time ) 2) Assigning CO1 calls to DKT1(100) : 1) Go to CO Line Base Program/CO Ring Assignment (PGM144/145) in the menu tree and double clicking. 2) Choose CO line number 1 and press Refresh button. 3) Click the right button of mouse and click Update Tool 4) Select Mode as Day. Select Type as Station 5) Input 100~100 at Range Start and End. 6) Press update when you complete. 3) 4) 5) 6) Deleting default-assigned STA2(101) from CO1 : Go to step 3) above. Input 101~101at Range Start and End. Mark Delete Ring Assignment at the bottom of the window. Click update. Now, CO1 Incoming calls go only to DKT1 (100). 23 LG-Nortel Confidential Information

24 Basic Feature Advanced Feature 2-6-2) CO Ring Assignment Assigning which CO line incoming calls go to which station(s) This is the 2nd example of CO line call distribution 2 CO2/3 calls go to a station group (101~107) with circular ringing -one station ringing at a time. Before CO Ring Assignment, Hunt group should be preassigned in advance. 1) 2) 5) 3) 4) 5-1) 6) 5-2) Assigning Hunt Group : 1) Go to Station Group/Station Group (PGM190/191) in the menu tree and double clicking. 2) Click the right button of mouse and click Update Tool 3) Select Circular as Group Type. 4) Select on for Pick-up group attribute. 5) Add stations (101~107) from station list to Member field by selecting the station and pressing > button. 6) Press update when you complete. Now, Hunt Group 620 is successfully established 1) 3) 2) 3 Assigning CO2 to STA2~STA7 (101~107) : 1) Go to CO Line Base Program/CO Ring Assignment(PGM144/145) in the menu tree and double clicking. 2) Choose CO line number 2 and 3. press Refresh. 3) Click the right button of mouse and click Update Tool 4) Select Mode as Day. Select Type as Hunt Group and put the group number 620 5) Press update when you complete. 4) 5) Now, incoming calls from CO2/CO3 will go to STA2~STA8 (101~107). All idle stations will ring simultaneously. 24 LG-Nortel Confidential Information

25 Basic Feature Advanced Feature 2-6-3) CO Group Access Station Assigning which stations use which CO lines By default, when a station tries an outgoing call, the system seizes a CO line from CO1 to CO3, which is in the idle status. This can be modified appropriately to the customer requirements. For example, system can be programmed that certain stations use only certain CO lines. Below are the steps for this programming. 1 Divide CO lines as groups requested. By default, all CO lines are assigned as CO Group 1. 2 Then, assign a specific station or a station group to a CO group. Default Configuration Example For an outgoing call, a station can use any CO line which is idle in order. CO1~3 is grouped as CO group 1 by default. Let s assume a customer request as follows. CO1 is only used by Station 100 CO2 and CO3 are shared by station 101~107 steps to apply above examples. Assign CO2 and CO3 as CO Group 2 Assign 101~107 to use Group 2 (CO2/CO3) Detail procedures are on the next page 25 LG-Nortel Confidential Information

26 Basic Feature Advanced Feature 2-6-3) CO Group Access Station - which stations use which CO lines These are the programming procedure for the example. 2) 3) 1) 3) 2) 5) 1) 4) 4) 5) 6) 7) 5-1) Assigning CO2 and CO3 as CO Group 2 : 1) Go to CO Line Base Program/CO Line list (PGM140/141/142/143) in the menu tree and double clicking. 2) Input CO line number 2 and 3. 3) Click the CO Attr I button. CO line Attribute I (PGM141) window will pop up. 4) Click the right button of mouse and click Update Tool Update tool will be showed at the bottom side. 5) Put the CO number 2 and 3 6) Select the CO Group as 2. 7) Click update button.. Assigning 101~107 to use CO Group 2 (CO2/CO3) and Deleting 101~107 from CO Group 1 (CO1) 1) Go to Station base Program/CO Group Assess Station (PGM117/131) and double click. 2) Choose CO Group number as 2 3) Click the right button of mouse and click Update Tool 4) Input the station number 101 at Start, 107 at End and click Get button. 5) Mark the check box for Access CO Group 2 to add and uncheck the check box for Access CO Group 1 to delete, which is assigned by default. Then, click Update button. Now, CO2 and CO3 are grouped as CO group 2. And Stations 101~107 use CO group 2(CO2/CO3) as their CO lines for outgoing calls. 26 LG-Nortel Confidential Information

27 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. These are the programming examples for the most frequently requested items from the customers such as COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Station COS / CO COS (Class of Service) Station COS is to allow or deny types of calls from the internal stations with different levels of restriction/allowance rules. CO COS is to allow or deny types of calls on CO lines with different levels of restriction/allowance rule. By default in ipldk-60, all stations and CO lines are assigned as COS level 1, no restrictions. So, any types of calls like long distance or international calls can be made from any stations through any CO lines. There are 9 different levels of COS setting (V3.7Ff version) on both station and CO, which can be applied in combination. This can be programmed on either station or COS or Both. Below is the rule table. Generally, station COS rules cover most of the requirements. For example, Station COS level 2 is ruled by Exception Table A. Station COS level 3 is ruled by Table B. For this assignment, follow below 2 steps. 1 Make the exception table for allowance and denial for certain numbers. 2 Apply the COS level on stations or CO lines At next page, a simple example will be given. S T A T I O N C O S CO LINE COS Unrestricted Default Canned Unrestricted Unrestricted Unrestricted Restricted Canned 2 Table A Table A Table B Restricted Unrestricted 3 Table B Unrestricted Unrestricted Canned Unrestricted Restricted Canned 4 Table A,B Table A Table B Unrestricted Restricted Canned Canned Canned Canned 5 Restricted2 Restricted2 Restricted2 Restricted1 Unrestricted 6 Canned Canned Canned Canned Unrestricted Restricted1 Restricted1 Restricted1 Restricted1 Intercom Intercom 7 Intercom Only Intercom Only Intercom Only Only Only Canned 8 Table C Table C Unrestricted Restricted1 Unrestricted 9 Table D Table D Unrestricted Canned Unrestricted Restricted1 Typical usage. 27 LG-Nortel Confidential Information

28 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Station COS / CO COS (Class of Service) 1) 2) 4) 1) 2) 4) 3) 3) Making Toll exception table A : 1) Go to Tables/Toll Exception table (PGM 224) in menu tree 2) Click the right button of mouse and click Update Tool 3) Input any access code to allow and press Update button. Repeat step 3 if you have other numbers to put in. If you put 002 here, it means that any calls which start 002 are allowed. 5) 4) Click Deny A button right under Allow A. 5) Input any access code to deny and press Update button. Repeat Step 5 if you have other numbers to put in. If you put 003 here, it means that all calls starting 003 is restricted. Now, this means only 002 is allowed. Other than 002, all number starting 00 will be denied. Making Toll exception table A : 1) Go to Station Base Program/Display Station COS (PGM116/130) in menu tree 2) Click the right button of mouse and click Update Tool 3) Input the station range, 101 at start and 107 at End. Select Day COS as 2 and Night COS as 2 and click Update button. 4) COS can be displayed. Put the station range to check and click View button. The COS will be displayed for day and night. 28 LG-Nortel Confidential Information

29 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Flexible button assignment for digital telephone Flexible buttons on digital/ip telephones can be programmed and used in many ways. On each flexible button, CO line, Station, Speed dial number or Frequently Used Functions can be assigned. With these assignment, the assigned function is executed with a click of the button. This assignment can be performed via PC-Admin Program very easily. This will be explained with examples with most typical cases. By default, Flexible button 1 to 8 are assigned as followings in left picture below. Both pre-assigned buttons and N/A(Not Assigned) buttons can be assigned with new designations as requested. Here most typical cases will be explained with examples. Default Assignment [LDP-6230D] [LDP-6212D] 1 13 CO1 N/A CO2 N/A CO3 N/A CO4 N/A CO5 N/A CO6 N/A CO7 N/A CO8 N/A Loop N/A N/A N/A N/A N/A N/A N/A CO1 CO2 CO3 CO4 CO5 CO6 CO7 CO8 Loop N/A N/A N/A Example Assignment [LDP-6230D] CO1 CO2 CO SS1 SS2 SS3 SS4 SS5 SS6 SS7 SS8 SS9 SS10 Functions N/A Assign station number 100~107 on Flex 5~12 2. Assign 10 Speed dial numbers (10ea) on Flex13~22 3. Assign Functions on Flex LG-Nortel Confidential Information

30 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Flexible button assignment for digital telephone 1) 2 ) 3 Update tool ) 4 ) 6) 7) 8) 9) Assign station # 100~107 on Flex 5~12 respectively : 1) Go to Station Base Program/Flex Button Assignment (PGM115/125) in menu tree 2) Put the station number and click the Refresh. 3) Click the right button of mouse and click Update Tool again. 4) Click the flexible number 4. Select Type as {Station xxxx} and input the station number as 100. Then click Update button. 4-1) Repeat step 4 for flexible button 5~12 in the same way. Now, direct call can be made to the internal assigned station with one touch of the flexible button. Assign 10 Speed dial numbers (10ea) on Flex13~22 : 6) Click the flexible number 13. 7) Select Type as {System Speed xxxx} and input system speed bin number(storage number) as Then click Update. 7-1) Repeat above step 6 for flexible button14~22 in the same way as above Assign Functions on Flex23 : 8) Click the Flexible number 23. 9) Select Type as Pickup and Value as Group call pick-up and update. 30 LG-Nortel Confidential Information

31 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Registering system speed dial list via Speed Editor There are two types of speed dial functions. 1)System speed dial The numbers can stored in the shared storage, upto 500 numbers. Number range : 2000~ )Station speed dial The numbers are stored in the individual storage, upto 100 numbers. Number range : 00~99. This gives the guide how to make the system speed number list via PC-Admin. These system and station numbers can be also stored via a station. Refer to the manual for the details. 3) 4) 4-1) Linking the Speed Editor Program 1) Get the speed editor program from the CD-ROM for manuals or go to 2) Run the PC-Admin Program 3) Go to Utility/Speed Editor path and click. 4) Browse the path where Speed Editor program is stored and click ok. 2) 1) 3-3) 3-2) 3-1) Connecting the system 1) At PC-Admin, go to Utility/Speed Editor 2) At Speed-Editor,go to Connection/Connect 3) Set the IP Address of the system to connect and click Ok. Click Connect again 3) 3) 1) 2) 2-2) 1) 2-1) 2-1) 2) Downloading existing Speeddial number from system 1) Go to File transfer /download 2) Select the range. Select where to download 3) Then, open the file and update Uploading The updated Speed-dial number from system 1) Go to File transfer /upload 2) Browse the file and click ok 31 LG-Nortel Confidential Information

32 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Assigning MOH tone ipldk-60 system provides high-quality MOH (Music on hold). When a call is placed on hold, system provides a Music on Hold. There are 13 kinds of MOH in ipldk-60. By default, Romance is pre-assigned and this can be easily changed as followings. 1) Go to System Base Program/Music (PGM171) in the menu tree and double click. 2) Select any on the list. 1) 2) 32 LG-Nortel Confidential Information

33 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Doorphone Doorphone can be installed on the front door of a company and a call by any visitor can be placed to the specific station (attendant). As well, automatic door open function can be assigned. Doorphone installation example 1) Choose the place for the doorphone and install it. For the detail guideline, refer to the Hardware installation manual. Cable the doorphone and any station port in the system as the same way for digital terminal cabling. 2) After hardware installation, following 2 cases need to be programmed. Doorphone assignment for station 101 port should be set on (ICM Box signaling on) Flexible button for Doorphone (107) needs to be assigned on station ) Door Lock 3) 2) With this button set, the designated extension can receive the call and open the door 3) For automatic door open, install proper relay on the door and cable to one of relay contacts (1~4). This example is the case to use relay contact 1 Then, you have to set this relay contact as for door open (PGM168) For door open, press (#*1) on the designated station. 33 LG-Nortel Confidential Information

34 Basic Feature Advanced Feature 2-6-4) Change the default values for the most frequently requested features. COS(call restriction setting), Flexible button assignment for digital/ip telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system. > Doorphone 1) 2) 3) 4) 5) 6) 7) 8) Assign station 101 as doorphone extension : 1) Go to Station Base Program/Station List (PGM110/111/112/113/114) in menu tree. 2) Put the station number for doorphone box as 101 and click fresh. Click the right button of mouse and click Edit Tool. 3) Check the ICM Box signaling on. Then click Edit OK. Then click update for save. Assign a flexible button on 101 as designated extension for doorphone : 4) Go to Station Base Program/Flex Button Assignment(PGM115/125) in menu tree 5) Put 101 at station number and click refresh. 6) Choose a flexible button and click the right button of mouse. Then click update tool 7) Choose Station xxxx and input 107 at the Value position. then update. Assign relay contact for automatic door open : 8) Go to Station Base Program/External control contact (PGM168) in menu tree 9) Click the right button of mouse and click Update Tool. Set contact as Door open and click update. 34 LG-Nortel Confidential Information

35 Version 1.0 ipldk-60 Quick Installation Guide Simple integrated version of manuals for installation and programming Step 3 Advanced Feature

36 Advanced Feature Step 3 provides the procedures to configure the advanced features. With these features in proper use, a great deal of ipldk-60 system features can be delivered to the customers. 3-1) DB upload / download (Page 36) 3-2) Software upgrade (Page 38) 3-3) E1R2 (Page 40) 3-4) PRI (Page 43) 3-5) Hunt Group UCD (Page 50) 3-6) Installing VOIB board (Page 52) 3-7) IP Extension Phontage (Page 54) 3-8) IP Extension IP Phone (Page 56) 3-9) SIP Trunk Service (Page 58) 3-10) Off-line PC-Admin (Page 60) 3-11) LCR (Page 61) 3-12) CCR (Page 63) 2 LG-Nortel Confidential Information

37 Advanced Feature 3-1) Database Upload/Download For the effective management of system admin, DB can be easily downloaded and uploaded. During DB download, ipldk-60 can be in normal operation. During DB upload, no admin changes are allowed by PC-Admin or Keyset Admin. After DB upload completion, ipldk-60 will be reset automatically if Automatic reset is on Advantages as follows - Database Backup/Restoration for emergence cases or any type of failures. - Downloaded DB file can be edited for upgrade or reuses for other similar customer sites without live connection to ipldk-60 Use Off line PC Admin program for off-line DB editing refer to Step 3-10). - Local or remote connection is supported (LAN/Modem, *Serial connection - local only) 3-1-1) Database download 3-1-2) Database upload Here, Up/download via LAN will only be explained (it is most simple) 3-1-1) Database download 1) 3) 1-1) * Check system IP/gateway address in advance. (PGM108) 1) Start the PC-Admin. Without system connection, click the LDK Utility/ LDK DB Upload/Download and select the system type as ipldk-60 2) Select DB download and check TCP Connection. 3 LG-Nortel Confidential Information 2) 2-1) 4) 3) Input the system IP address to connect and Admin Password (No password by default.) * For remote connection, Public IP should be assigned on the connected system in advance. 4) Browse where to save with the DB name. Then click next. Downloading monitor trace box and progress window to be popped up (See the next page).

38 Advanced Feature 3-1) Database Upload/Download 3-1-1) Database download (Continued) 3-1-2) Database Upload. 2) 5) 3) 6) 7) 4) 8) 5) Click the Start button. DB download will be started. 6) DB file transferring status will be shown with a pop-up window. 7) Success pop-up will be shown if it is performed successfully. 8) Click No to end. Database upload can be done locally or from the remote site. The DB should be ready in advance. The overall procedures are quite the same as DB Download described at 3-1-1) Database download At step 2) DB upload should be checked At step 4) Browse the DB to upload. Then, click the start at Step 5 Others are exactly the same as DB download 4 LG-Nortel Confidential Information

39 Advanced Feature 3-2) Remote Software Upgrade System Software can be upgraded remotely via TCP/IP or Dial-up modem connection. With this capability, a lot of time and cost can be saved. ipldk-60 system should be assigned with an Public IP address in advance. * In local connection, private IP is ok. PC and system are set to be in the same zone. New system software(i.e. GS88P-38AP.bin) should be prepared in advance. Existing database in old software automatically fits into the new software. 1) 3) 2) 4) 1-1) * Check system IP/gateway address in advance. (PGM108) 1) Start the PC-Admin. Without system connection, click the LDK Utility/LDK DB Upgrade and select the system type as ipldk-60 2) Select the connection type as TCP Connection. 3) Input the system IP address and Admin Password (No password by default.) 4) Browse the system software to upgrade. Then, click next. 5 LG-Nortel Confidential Information

40 Advanced Feature 3-2) Remote Software Upgrade (Continued) 7) 8) 5) 6) 7) Once new software (GS88P-38AP.bin) is successfully transferred and verified, system disconnect the session and start replacing the old software with new software at Flash ROM. Don t touch anything on the system while system replace software After completing the upgrade, ipldk system restart automatically 8) Click No to end. 5) Click the Start button. DB download will be started. 6) DB file transferring status will be shown with a pop-up window. If 6you press [Start] button, the transfer window will LG-Nortel be displayed. Confidential Information

41 Advanced Feature 3-3) E1R2 E1HB8 supports E1R2 signaling. Full 30 voice channels or fractional channels are supported as well ) E1R2 Board (E1HB8) Installation ) Board. - Check the CO line numbers (range) Full R2 channels (30channels), Fractional channels. - Assign CO type as DCO DID for R2 signaling. - Assign DCOB CO type for Both-way call service CO line. * By default, E1R2 is set as Incoming DID line (Incoming DID call only no outgoing call via this CO lines) 3-3-1) E1R2 Board Installation 2) 1) 1) Install E1HB8 at CN2 on the BKSU 2) Wiring the cable between E1R2 and DSU equipment Cabling Guide TYPE Pin Number NO SIGNAL NAME RJ45 3,6,7,8 RESERVED 1 TX+ 2 TX- 4 RX- 5 RX+ 3) Connect the E1R2 line on the port of E1H8 board. * DSU and E1 line should be previded by a service provider in advance 7 LG-Nortel Confidential Information

42 Advanced Feature 3-3) E1R ) Board 1) 2) 3) 4) 2-1) 1) Go to pre-programmed/configuration (PGM101~103) in the menu and double click. 2) Position the mouse on slot 6 DCOB and click the right button. Select CO Data View 3) Position the mouse CO line4 and click the right button. 4) Click again the Update tool 8 LG-Nortel Confidential Information

43 Advanced Feature 3-3) E1R ) Board (Continued) 7-1) 7) 8) 5) 6) 6-1) 9) 10) 10-1) 5) Input CO range. If 10 channels are used, put 4~13. 6) Then, choose type as DCO DID for R2 signaling. Click update. 7) Input CO range 4~13. Click Refresh. CO information to be popped. 8) Click the right button of mouse then click Update tool again. 9) Input CO range at 4~13. 10) Select DCOB CO type as 0(Cyprus) for both-way call. Then update. 9 LG-Nortel Confidential Information

44 Advanced Feature 3-4) PRI Pre-requisite before PRI installation and programming. - How many simultaneous calls(pri Channels, which is CO lines) and how many DID numbers to use(destination stations) should be decided by the customer and contracted with the service provider. -Station numbers could be assigned the same as DID numbers subscribed from the Telco or can be assigned based on internal station number plan differently. -PRI channels(co lines) are not directly dedicated to the specific station numbers. So, this should be handled by the system. To do so, ipldk-60 should be programmed properly. -With the shared-use mechanism of PRI channels by any stations, it is required to give the caller s ID (DID number) to the callee for any outgoing calls. In order to do this by ipldk-60, it is required to be programmed as outgoing caller ID assignment - For any incoming DID calls, it is required to convert the DID number to the dedicated internal station number if the station numbering plan is different from the subscribed DID numbers. Here, this will be explained with one of typical examples a.10 PRI channels to be subscribed which will be assigned as CO4~CO13. (There is basic CO1~3 so, next 10 CO channels are assigned from CO4 to CO13. if 30 channels are subscribed, it will be CO4 ~ CO33) b. Subscribed DID numbers are ~5024 (24 stations) c. Internal station numbers are assigned the same as the DID subscriber number. Procedures to program the above case ) PRI Board (PRHB8) Installation on BKSU ) Assign the station number from 5001~5023 refer to Basic feature Step ) Assign CO type as ISDN DID 3-4-4) Outgoing Caller ID assignment Station number conversion to DID number 3-4-5) Incoming call assignment DID number conversion to station number Station DID numbers numbers ) 10 PRI Channels PRI 2) Subscriber numbers ~ LG-Nortel Confidential Information

45 Advanced Feature 3-4) PRI 3-4-1) PRHB8 Board Installation on BKSU 1) 1) Install PRHB8 at CN2 on Basic MBU(BKSU). * DIP SW4 of PRHB8 should be at PRI position. 2) 2) Wiring the cable between PRHB8 and DSU equipment as guided. (4wire cabling) 3) Connect the PRI line on the port of PRHB8 board. * DSU and PRI line should be provided by a service provider in advance Cabling Guide TYPE Pin Number NO SIGNAL NAME RJ45 4,5,7,8 RESERVED 1 TX+ 2 TX- 3 RX- 6 RX ) Assign the station number If the basic numbering plan is to be used, this step can be skipped. If necessary to assign the station number, refer to the Step 2-1) the basic feature programming. 11 LG-Nortel Confidential Information

46 Advanced Feature 3-4) PRI 3-4-3) Assign CO type as ISDN DID This is to assign the incoming calls to go to the destination directly. 1) 4) 2) 3 2-1) Assign CO4~33 as ISDN DID 1) Go to pre-programmed/configuration (PGM101~103) in the menu and double click. 2) Position the mouse on slot 6 PRIB and click the right button. Select CO Data View 3) Position the mouse at the CO number 4 and click the right button. Click the Update tool. Put the CO number range for 4~33, select the type as ISDN DID. Click update. 4) Click CO ISDN Attr button on the right top side 12 LG-Nortel Confidential Information

47 Advanced Feature 3-4) PRI 3-4-4) Outgoing caller ID assignment Since the PRI channel is commonly used, the system should give the callers ID (DID number) to the PX on every outgoing call to give the right CID number to the callee. If this is not programmed, the PX will provide the caller ID randomly among the subscribed DID numbers, which will be wrong generally. Area code PRI PX code Subscriber number 5) 6) 4) 4-1) 4-2) 4-3) 137) 7-1) 7-2) 4) Input the CO range. Then Select CLIP Table Idx as 0, Call type as National, CLI type(0~2) as Normal and click update. Leave others unchanged. 5) Then click the CO Attr III button. 6) Click the right mouse button on CO line 4 and click the update tool again. 7) Input the CO range. Then Select Outgoing prefix code insert as off. Then update. 13 LG-Nortel Confidential Information

48 Advanced Feature 3-4) PRI 3-4-4) Outgoing caller ID assignment (Continued) 8) 8-1) 9) 9-1) 9-2) 8-2) Assigning Area code 8) Go to ISDN System base program/isdn Attributes (PGM200). Input area code 031 as in this example. Then update. 9-3) ) Assigning PX code 9) Go to ISDN System base program/colp Table (PGM201). Position the mouse at Index 0 and click the right button of mouse. Click Update tool. Input 450 then update. * No need to assign the subscriber number because it s been already assigned the same between the station number and DID number. 14 LG-Nortel Confidential Information

49 Advanced Feature 3-4) PRI 3-4-5) Incoming call assignment Incoming calls are distributed with the number provided from the Telco PX, which is 3-digit or 4digit at the last. Need to check with the carriers. ipldk-60 should be programmed accordingly with these numbers from the Telco to the destination PRI ) ) 10) Go to CO Line Base Program/CO line list (PGM140/141/142/143). Then, Go to CO ISDN Attributes(PGM143) by clicking CO ISDN Attr 11) 12) ) 12-1) 0 13) 12-2) 11) Position the mouse at CO number 4 and click the right button. Click again Update tool 12) Input the CO range number 13, Check DID remove number as 0. Click update. If the station number and DID number is different, this should be checked accordingly. 15 LG-Nortel Confidential Information

50 Advanced Feature 3-4) PRI 3-4-5) Incoming call assignment 13) 13-1) 13) Go to CO line Attribute III(PGM146) by clicking CO Attr III or directly click the PGM146 at the menu tree. 14) Position the mouse at CO line number 4 then click the right button. Click the Update tool 14) 14-1) 15) Input the CO range as 13. Select DID RCV Digit Number as 4. Input DID Digit Conversion ****. Then update. 15-2) **** 15) 15-1) ) 16 LG-Nortel Confidential Information

51 Advanced Feature 3-5) Hunt Group Stations can be grouped for incoming call routing and Call Pick-up purposes. 7 types of groups can be defined in ipldk-60, called as Hunt Group as a representative term for these groups. A type of group can be selected and programmed appropriately for the customer site usage. UCD(Uniform Call Distribution) will be exampled as the most typical type for small companies at next page For example, Station 100~103 are grouped as Ring and station 104~107 are grouped as UCD 1) Incoming calls to UCD group. A call is routed to the idle station in the longest among UCD group stations. 2) Incoming calls to Ring group. All stations will ring at the same time with new call. Ring Group CO1 call CO1~3 CO2 call CO3 call UCD Group Group Type Circular Terminal UCD Ring Voice Mail Pick-up Net VM Group Description A call is routed to hunt group. If first destination is unavailable or unanswered, the call is routed to the next station in the group. If the call is unanswered or unavailable, it is directed to the next listed station in the group. The call will continue to be routed until reaching the last station in the group. Calls are routed to the station in the group that has been idle for the longest time. All stations in the group will ring when a call is received. This group is assigned for Voice Mail and only the SLT assigned as the member of the VM group. A station can be assigned to a Call Pick-Up group and then may pick-up (answer) calls to other stations in the group employing the system s Group Call Pick-Up feature. This group is defined to support a Centralized Voice Mail system for a networked environment. At supported systems, the group is used to handle the AA/VM requirements from the central ipecs. The Net VM group may be an external VM system or the ipecs Feature Server. 17 LG-Nortel Confidential Information

52 Advanced Feature 3-5) Hunt Group - UCD Calls are directed to the station in the UCD group that has been idle for the longest time. If all stations are busy or unavailable when the call is received, the call may be routed to an alternate location or may continue to wait (queue) for an available station in the group. After queuing to the group, the caller may be routed to an overflow destination, which can be a Station, Station Group or Voice Mailbox. Here, only key operations will be guided. For details, refer to the manual ) Make a Hunt Group as UCD 3-5-2) Assign CO Ring Assignment 1) 1-1) 3) 3-1) 3-2) 2-1) 4) 2) 2-2) 4-1) 5) 5-1) 5-2) 5-3) 3-3) Make a Hunt Group as UCD : 3) Go to Station Group(PGM190/191). Position the mouse at group 620. Then click the right mouse button. Then click Update tool again. Update tool will be popped up. 4) Select the stations from the station list. Then click > to add in UCD member list. 5) Select Group as 620, Type as UCD, Pickup attribute On. Then update. 5-4) Assign CO Ring Assignment to UCD Group : 1) Go to CO Ring Assignment(PGM144/145). Position the mouse at Day field then Click the right button of mouse. Click Update tool. 2) Select Mode as Day, Type as Hunt Group, and Number as 620. Then Update. 18 LG-Nortel Confidential Information

53 Advanced Feature 3-6) Installing VOIB Board VoIP Interface Board should be installed to use VoIP features such as IP phone, Softphone or SIP trunk service from ISPs or multi ipldk-60 networking over IP. There are VOIB and VOIU, which supports 4 VOIP channels respectively. VOIB is mounted at CN14 on the basic MBU and VOIU is mounted on VOIB. The overall procedures to implement any VOIP features are 1) Install the VOIB board and Board 2) Then, Enable any VoIP Services to use : IP Phone, Phontage (Basic mode only), SIP Trunk Service Procedure to Install VOIB Board : Install the VOIB(4ch only) or VOB/VOIU (4+4ch=8ch) on basic MBU Set the IP/Gateway address of VOIB via PC-Admin. IP should be prepared with a public IP address. Set the number of channels for IP Phone use and IP Trunk use. 2) 5) 2-1) 2-2) 1) 3) 3-1) 4) 1) Install the VOIB (with VOIU) on the slot 10. Then, connect PC Admin to the system for VOIB Board 2) Go to Pre-Programmed/Configuration(PGM101~103). Position the mouse on VOIB. Then, Click the right button of mouse. Click again VOIB Data View (PGM340/341) 3) Input the IP and Gateway Address. 4) Check the SW1 DIP4 at Off position to save the new settings. 5) Click update. VOIB Board will be automatically reset. 19 LG-Nortel Confidential Information

54 Advanced Feature 3-6) Installing VOIB Board 1) 1-1) 8) 4) 2-2) 3) 5) 6) 6-1) Enabling the VOIB to be used for IP Extensions : 1) Go to Configuration (PGM101~103). Position the mouse at VOIB. Click the right button. Click Logical Assignment 2) Position the mouse on 10)VOIB then click the right button. Select (Virtual VOIB) Append to STA. 99 will be added to STA board column. Click update. 2) 2-1) 7) 7-1) Assigning the number of VOIP channel for IP extension & of the maximum IP extension number : 3) Go to RSG/IP Phone /VOIB Slot for RSG/IP(PGM380) 4) Select VOIP slot for RSG/IP and click > to add. 5) Select VOIP slot as 10 6) Select number of VOIP channel and click update. 7) Select the number of IP extensions to use and update 8) Click the update on the top to complete. 9) System should be reset to database rearrangement 20 LG-Nortel Confidential Information

55 Advanced Feature 3-7) IP Extension - Phontage Phontage is the LG-Nortel proprietary IP Softphone that works only with LG-Nortel ipldk-60 system. (Phontage Basic version only). Phontage is controlled by License system so the license by copy should be purchased and installed in the system. Basically 2 copies are embedded as free of charge. 1) VOIB Board should be installed. (VOIB-4ch, VOIB+VOIU -8ch) 2) License for Phontage Basic (LIP-SP) should be downloaded and installed on the system. 3) Set the system 4) Install Phontage program on the PC 2) 3) 4) 1) Go to LDK Utility/LDK Remote Diagnostic at the Menu Bar on the top 2) Connect via LAN (Input the IP Address at the LAN configure. Then click the LAN connect. Input Password jannie 3) Input the command q d. 4) The license status can be checked. 1) Get the lock-key required through LGN Lock-key download Web-site (Refer to the Lock-key download guide ) 2) Open the Telnet connection to the destination system. 3) Input password jannie 4) Input license installation command followed by license. q w 9 (lock key) 5) Check if the license is properly installed with the command q d 6) Reset the system. 21 LG-Nortel Confidential Information

56 Advanced Feature 3-7) IP Extension - Phontage 1-1) 1) 2) 3) 5) 1) 2), 3) 3-1) Registering User ID/Password for the phontage users : 1) Go to IP Phone Attribute (PGM386). Position the mouse at Bin No 1 and click the right button. ID/Password setting menu to be displayed at the bottom. 2) Input the ID/Password for Phontage for each user. 3) Repeat Step 2 until complete all the users ID and Password. Update. Now, the phontage users can login in with the pre-registered IP/Password. Installing the Phontage Software on user s PC : 1) Get the Phontage Software from distributors/resellers. 2) Install the Phontage Basic program. Follow the installation wizard 4) Setting the Network and Login : 1) Start the Phontage client software on the PC. Log-in window to be popped up. Click the Network button to set the network configuration. 2) Check the connection mode as Remote. 3) Input the VOIB IP address. Click OK. 4) Enter User ID/Password, pre-programmed at PGM386. 5) The main window will be popped up (Refer to the user guide for the detail operation.) 22 LG-Nortel Confidential Information

57 Advanced Feature 3-8) IP Extension IP Phone LG-Nortel IP phones (LIP-6030D, LIP-6012) can be registered in ipldk-60, which can be installed in the company LAN or outside, for example at home remotely. Up-to 16 IP Terminals (including Phontage) can be registered in the system and the maximum simultaneous call depends on the VOIB/VOIU channels upto 8 channels. 1) VOIB/(VOIU) should be installed in advance 2) Register the MAC address of IP Phones to get the authentication from the system get the MAC address from the bottom side of the phone. 3) IP Phone programming LAN LAN(VOIB) router LIP-6030D LIP-6012D Phontage LIP-6030D 1) 2) 3) 3-1) Registering the MAC address of IP phones : 1) Go to RSG/IP Phone (IP Phone Attributes (PGM386). 2) Position the mouse at the MAC Address and click the right button. Click Update tool. 3) Input the MAC address of IP Phones one by one. : should be inserted between 2-digit number. Then, update. 23 LG-Nortel Confidential Information

58 Advanced Feature 3-8) IP Extension IP Phone IP Phone should be programmed on the phone. 1)Install the IP Phone and Cabling. 2)Setting the Mode as Remote (ipldk-60 only supports remote mode. So, it should be set as Remote both at local and at remote connection. 3)Setting the IP address of system (VOIB) 4)Setting the IP address of IP Phone : At home => DHCP mode, at company => Fixed or DHCP 5)Rebooting. IP Phone tries to connect to the system and connected. DHCP? [DISABLED] CHANGE[#} NO RESPONSE FROM MFIM[L] SET[*] - RETRY[#] MODE[R/L] [REMOTE] - CHANGE[#] MFIM IP ADDRESS(DOT:*) a REBOOTING AFTER SETTING 4-b PHONE NET MASK(DOT:*) ROUTER IP ADDRESS(DOT:*) PHONE ADDRESS(DOT:*) IP 1) Power on the IP Phone. the following message will be displayed on LCD. Press * to enter the setup. If password requested, press * by default. 2) The following message will be shown. Leave the mode as Remote as default set. Move the menu to the next by using Volume up/down button. To change(toggle) the value press #. 3) Input the IP Address of system(voib). Press Hold/Save button to save. Press Speaker 4-a/b) Set DHCP enabled or input fixed IP address for the IP phone. In general, DHCP mode at home and Fixed IP mode at office. 5) Upon completion, press Hold/Save then press Speaker. It will be rebooting to get connected to the system. 24 LG-Nortel Confidential Information

59 Advanced Feature 3-9) SIP Trunk Service ipldk-60 has been homologated for a list of carriers softswitch so a certain level of SIP trunk service can be provided. The compatibility to the carriers softswitch should be checked in advance. If it is not in the list, the IOT should be processed first. 1)VOIB installation refer to 3-6 2)SIP Trunk Compatibility check - refer to the attached the compatible list. 3)SIP Trunk programming. LAN LAN(VOIB) SIP Trunk router SIP Server (VOIP Carriers) SIP Phone 1) 2-1) 1-1) 3) 3-1) 4) Selecting VOIB mode as SIP trunk : 1) Go to VOIB/Gatekeeper setting (PGM340/341). Before this VOIB address should be properly installed. 2) Set VIOB Mode as SIP and update. 2) 5) 5-1) 5-2) Setting SIP trunk as Incoming/outgoing mode : 3) Go to CO line list (PGM140/141/142/143). Insert CO Number of VOIB Board. 4) Position the mouse on the first CO number and click the right button. Click Update tool 5) Put the CO Number range at End. Select Type ISDN DID. Update. 25 LG-Nortel Confidential Information

60 Advanced Feature 3-9) SIP Trunk Service 7-1) 7) 11-2) 7-2) 11) 6) 10) 8) 8-1) 8-2) 11-1) Setting SIP CO line attributes : 6) Go to Network/Networking CO line Attribute (PGM322). 7) Input SIP CO range and click refresh button. Position the mouse at the first CO line number and click the right button. Click update tool. 9) Input the CO line range, Networking CO Group as 1, VOIP Mode as SIP. Click update. Setting SIP Proxy/Domain Server Address : 10) Go to VOIB/Gatekeeper / SIP Attribute 1. 11) Input SIP Proxy Server and Domain Address. Get these addresses from the ISP in advance. Update. 26 LG-Nortel Confidential Information

61 Advanced Feature 3-10) Off-line PC Admin ipldk-60 can be administered via PC-Admin program by connecting PC and system in real time. In this case, any changes are applied in real time while operation. On the other hand, administration can be performed without connecting PC and system, which is called Off-line PC-Admin. In this case, any changes will be saved as database file(xxx.usr) and should be uploaded to get it applied to the system. 2 different admin programs are provided. 1) On-line PC-Admin - PC-Admin Refer to the step 2-3) or PC-Admin user guide 2) Off-line PC-Admin - PC-AdminPro Quick instruction will be given here. Off-line PC Admin Open the DB DB (xxx.usr) (yyy.usr) 3) 2) 1) 4) On-line PC Admin 1) xxx.usr data file should be downloaded from DB up/download menu of On-line PC-Admin. 2) Run the Off-line PC-Admin without connecting system and make modifications. 3) Save the changed date base as yyy.usr file. Modifications Save 4) Upload to the system via DB up/download menu of On-line PC-Admin. *PC-Admin and PC-Admin Pro can reside on the same PC or different PCs. 27 LG-Nortel Confidential Information

62 Advanced Feature 3-11) LCR LCR is a system programmable feature that automatically selects the least expensive available route when an outgoing CO call is made. With this feature enabled properly, system automatically convert to the least cost route when a user dials any access code. As well, this feature can be differently programmable by time during day and night and by day during week. 1) Planning the LCR route with the customer (Routes, Time zone, Day zone) 2) Select LCR Access code and day zone and time zone 3) Make LCR Table (LDT-Least Digit Table) 4) Make DMT Table (DMT-Digit Modification Table) Telco A (001) Telco B (002) Telco C (00700) Assigning LCR Access Code and Day/Time zone : 1) Go to Tables/LCR Assignment(PGM220). 2) Select LCR Access Code as M12 / Internal, Loop, Direct CO LCR. Set the Day Zone as requested. In this example, it s skipped. (For details, refer to xxx) 3) Set the Time zone as ZONE1 (6~21), ZONE2(0~5), Zone3(22~23) *Note : There are 6 LCR Access Codes are available depending on how to access the CO line like Internal LCR, Loop LCR, Direct CO LCR. Above M12 in this example covers all above cases. 28 LG-Nortel Confidential Information

63 Advanced Feature 3-11) LCR 1) 2) 3) 4) 5) 2-1) 2-3) 2-2) <Assigning the day 5-1) zone and 5-2) time zone> 5-3) Assigning LCR Table, which is called LDT Table : 1) Go to Tables/LCR-LDT Table(PGM221). 2) Position the mouse at Index 0 and click the right button. Click again the Update tool. Input any network access code at Compared digits and select the time zone to be compared and click update. * Note : This code will be automatically replaced with the other code at DMT table as set. (To be explained at the right) 3) Repeat step2) above if there are more access codes to be replaced with other code. Assigning DMT Table : 4) Go to Tables/LCR-DMT Table(PGM222). 5) Position the mouse at Index 0 and click the right button. Click again the Update tool. Input any network access code at Added digits and select the time zone and click update. * Note : This code will automatically replace the access code in LDT table based on the time zone rule. 6) Repeat step5) above if there are more access codes to be replaced with other code. 29 LG-Nortel Confidential Information

64 Advanced Feature 3-12) CCR CCR is the programmable feature that provides the announcement for the callers to select the destination. When a call is answered by a system programmed with CCR, a VMIB announcement should be heard by the caller. VMIB announcement gives a choice of destination and the caller may select a destination based on the information presented in the VMIB Announcement. Below is a typical example for operation. Procedure and Check point : 1)CCR Scenario planning 2)VMIU or AAIU should be installed. 3)Announcement should be recorded as the scenario. 4)CO lines should be assigned as DISA to provide this announcement service. 5)CCR programming. Caller Level1) Announcement Hello, this is xxx Company. Please dial the extension number. If you don t know the number, dial 1 for Sales Department, dial 2 for Technical Department and dial 0 for Operator. Thank you. 101 Hunt Group 620 (UCD Group) Operator Level2) Announcement for Sales Team Hello, This is Sales Team. Please dial Hunt Group 621 desired number. If you (Ring Group) don t know, dial 1 for Sales 1 part(hunt 620), dial 2 for Sales 2 part (Hunt 621) and dial 0 for operator. Thank you James Thomas Level2) Announcement for Support team Hello, This is Support Team. Please dial desired station number. If you don t know, dial 1 for James (STA106), dial 2 for Thomas (STA107) and dial 0 for operator. Thank you. CCR Scenario Planning 2 level-ccr case is exampled : A new call comes in, ipldk-60 gives the company announcement #1 at Level1) Case 1) If the caller selects 1 : The call will be routed to sales team Level2) If 1 selected, The call goes to sales1 part as Ring group operation Level2) If 2 selected, It goes to sales 2 part as UCD group operation Case 2) If the caller selects 2 : The call will be routed to Support team Level2) If 1 selected, The call goes to James (106) Level2) If 2 selected, It goes to Thomas (107) Case 3) If the caller selects 0 : The call goes to the operator 30 LG-Nortel Confidential Information

65 Advanced Feature 3-12) CCR VMIU/AAFU Installation Voice Mail Interface Unit (VMIU) or AA function Unit (AAFU) should be installed to provide company announcement services such as system announcements, ACD/UCD announcements, and User Greetings. VMIU/AAFU provides the same services with different memory capacity. 1) Install VMIU or AAFU at slot #9 (CN5) on Basic MBU Assigning the CO lines as DISA line The incoming CO lines are needed to be assigned as DISA to give this service. 2-1) 1) 2) 3) 4) 4-1) 4-2) 4-3) * VMIU vs AAFU VMIU AAFU Channels 4 4 Max record time System Greeting User record time 99 9 Max number of recorded messages ) Go to CO Line Base Program/CO Line List (PGM140/141/142/143) 2) Input the CO line range to be assigned as DISA. And click refresh. 3) Position the mouse at CO Num 1 and click the right button and click update tool. 4) Input the CO line range. Select the DISA On at Day check box. Input the VMIB msg number (storage number) and click update. 31 LG-Nortel Confidential Information

66 Advanced Feature 3-12) CCR Pre-recorded announcements Attendant Station (101) Direct Recording the announcements via the attendant station : 1) For level 1 announcement, press [ TRANS/PGM ] (Storage number) at the attendant station(101). 2) To start record, press # and then record Level 1 Announcement. Press [ HOLD ] to end the recording. This will be saved at VMIB storage number 1. 3) For level 2-1 announcement, press [ TRANS/PGM ] at the attendant station (101). 4) To start record, press # and then record Level 2-1 Announcement. Press [ HOLD ] to end the recording. This will be saved at VMIB storage number 2. 5) For level 2-2 announcement, press [ TRANS/PGM ] at the attendant station (101). 6) To start record, press # and then record Level 2-2 Announcement. Press [ HOLD ] to end the recording. This will be saved at VMIB storage number 3. Pre-recording at the studio and uploading via the attendant station : 1) Get the announcements recorded in advance and connect the source device to the External MOH port in the system as in the figure. 2) To upload the announcements, press [TRANS/PGM} at the attendant station. Press # and start the announcement at the source device. Press [Hold] when it s completed. 3) Repeat for 2nd and 3rd announcements as above. 32 LG-Nortel Confidential Information

67 Advanced Feature 3-12) CCR 5) 2) 3) 4) 6) 9) 7) 8) 10) 13) 11) 12) 1) Assigning the 1st level scenario : 1) Go to Tables/Customer Call Router (PGM228). 2) Select the Index as 1 meaning for the 1st level scenario. 3) Select the 1st destination as VMIB and input 2 for the 2nd announcement. 4) Select the 2nd destination as VMIB and input 3 for the 3rd announcement. 5) Click update. Assigning the 2-1 level scenario : 6) Select the Index as 2 meaning for the 2st level scenario 7) Select the 1st destination as Hunt Group and input ) Select the 2nd destination as Hunt Group and input ) Click update. Note that Hunt Group 620/621 should be assigned properly in advance as the scenario. Hunt Group 620 : Station 102/103 Hunt Group 621 : Station 104/105 Assigning the 2-2 level scenario : 10) Select the Index as 3 meaning for the 2-2 scenario. 11) Select the 1st destination as Station and input ) Select the 2nd destination as Station and input ) Click update. 33 LG-Nortel Confidential Information

68 Appendix A. Customer Requirements Checklist B. Documentation Reference Table C. Quick Terminal User Guide D. ipldk-60 IP Network Configuration Guide 34 LG-Nortel Confidential Information

69 A. Customer Requirements Checklist Check lists 1.How many stations (Digital, Analog, IP, Softphone)? 2.How do you like station numbers? 3.Do you want to make station groups & how to give ring? (All ringing, Circular, UCD, etc) 4.How many CO lines (CO, R2, PRI)? 5.What are the numbers? 6.How to dedicate CO lines to stations? (CO Ring Assignment) 7.Other stations can pick-up the call for other stations? 8.Outgoing call access to CO lines from stations? (CO Group Station Access) 9.Specific Features Example Default : 100, 101, 102, New : 1000, 1001, 1002, G1 : 100~103(All ringing) G2 : 104~107(UCD ringing) CO-6 lines or R2-10 channels CO1~3 : xxx-xxx1~xxx3 CO1 Group1 CO2/3 Group2 Yes or No 100 CO1 101~107 - CO2/3 1) Company Greetings scenarios Yes or No 2) Outgoing call restriction by stations Yes or No 3) Specific network services (access code) Yes or No 4) Speed dial planning Yes or No 5) Flexible button assignment for digital/ip keysets Yes or No 6) Remote IP/Softphone Yes or No Customer Requirements Recommendation 35 LG-Nortel Confidential Information

70 B. Documentation reference guide These are the manual & user guide lists for ipldk-60. All manuals are available from CD-ROM on the main system and LG-Nortel Web-site ( * Note that the manual names and versions are subject to change items Remarks Quick Installation Guide (HW & SW) Hardware Installation Manual ipldk-60 QIG Global_ipLDK-60 IM_Issue1_1.doc Global_ipLDK-60 programming_issue1_1.doc Global_ipLDK-60 Feature Description_Issue2_0.doc By PGM number By Features User guide for ipldk-60 PCADMIN v381 To Brazil.doc Software Manual User guide for PCAdminPro_ipLDK60_V381_ doc SWUpgrade_Manual_IpLDK60.doc DBUpDown_Manual_ipLDK60.doc LG-Nortel TSP User Guide 37Aa.doc Lock-key download manual ez Phone User Guide_ipLDK-60.doc Application User Guide User Guide for ezatd_issue2.doc Phontage User Guide _issue1.doc ipldk-60_ldp_6212_30d_ug for digital telephones Terminal User Guide ipldk-60_lip_6012_30d_ug for IP telephones SLT User Guide for analog phones 36 LG-Nortel Confidential Information

71 C. Terminal User Guide Digital Phone / IP Phone No. Buttons Functions 1 Handset Handset device 2 Earphone socket Headset connection 3 Speaker phone Output tons and voice 4 SPEED Used for Speed dialing, Speed programming, Save number redial, Last number redial 5 DND/FWD DND (Do Not Disturb) : Blocks all incoming calls (Red LED) FWD : Forward to another station or voic (Red LED) 6 Volume Adjust audio level for ringing, handset and speaker phone 7 ON/OFF Speaker toggle button (ON/OFF) 8 HOLD/SAVE Put a call hold or save information when programming LDP-6230D 9 3 Soft Keys Select or setup various function(s) indicated on LCD panel in relation to call process. Ex) PICKUP/CONF/REDIAL in Idle Status (Please see Keyset manual for detailed functions) 10 LCD Information display and program setup : Telephone status / Dialing directories / Test messages 11 LED Lighting when the phone is ringing 12 Trans/PGM Initiate call transfer function or enter programming mode 13 CALL BK A station can initiate a call back request to busy station. : Leave a call back request or voice message to destination station in busy status Cable connection 14 Flexible buttons Assign some functions to the flexible buttons Direct station selection, Call park, Speed dials buttons, etc.. Ring type, Set Wake-up Time, etc.. Button assignment (CONF,DND, MUTE, LOOP,..) 15 Handsfree MIC. Using with handsfree speakerphone 37 LG-Nortel Confidential Information

72 C. Terminal User Guide SLT(Single Line Telephone) No. Functions Description 1 Placing an Outside Call Dial 9 2 Placing an Intercom Call Dial Intercom Number directly 3 Last Number Redial Dial Group Call Pick-up Dial Call Forward Dial and dial desired call forward number 1/2/3/4 unconditional/busy calls/no answer calls/busy or no answer calls 5 Station off-net, unconditional with speed bin., 6 Station off-net, no answer with speed bin., 7 Incoming outside line off-net (ATD only) 8 Station unconditional off-net with telephone number 9 Station No answer off-net with telephone number To make Call Forward to VMIB, press # key after dialing call forward type 1~4 To make off-net forward type 8 or 9, press hook switch after entering telephone number Dial the station number or Hunt Group to forward incoming calls to, (Station : 100 ~ 151, Hunt Group : 620 ~ 629) Hang up To cancel Call Forward, dial and # or dial DND (Do Not Disturb) Dial To cancel DND, dial Note : Numbering plan code can be changed by Admin 104 ~ 107, LG-Nortel Confidential Information

73 D. ipldk-60 IP Network Configuration Guide Sample 1 : Standalone Configuration for Local/Remote > Step 1 : Network connection for Internet access - Setup Router configuration to guarantee QoS for VoIP and IP address : It depends on the existence of remote IP Phone to set the IP address of Router to fixed or dynamic. > Step 2 : Configuration of ipldk-60 The IP address of ipldk-60 system always should be set to Static IP whether Router gives fixed IP or not through DHCP function. And you have to choose and set the IP address of ipldk-60 within the boundary of DHCP allocation table in Router. The following table shows the IP allocation of Router and ipldk-60. Local IP Phone only Remote IP Phone Router Fixed / Dynamic IP Fixed IP ipldk-60 Static IP Static IP > Step 3 : (Remote) IP Phone configuration The following table shows the methods of system IP setup of local IP phone and remote IP phone. Fixed Dynamic (DHCP) Local Phone ipldk-60 IP address ipldk-60 IP address Remote Phone ipldk-60 IP address Router IP address Fixed IP : Public IP Static IP : Prescribed IP from user or public IP 39 LG-Nortel Confidential Information

74 D. ipldk-60 IP Network Configuration Guide Networking Configuration for ipldk-60 systems ipldk-60 provides networking feature makes possible to operate one network among widespread systems. With this networking feature, - All stations under each site can directly call the other stations as if intercommunication. - In general, Master has CO lines and every Slave can use those CO lines across the internet as if inner CO lines. A B > Step 1 : Network connection for Internet access - Setup Router configuration to guarantee QoS for VoIP > Step 2 : Configuration of ipldk-60 - All ipldk-60 systems should have fixed IP address - Compose matrix table for the IP and setup those information to each system with PC-Admin program For example, the following address will be set to each system. Headquarter IP address Branch A) IP Address Branch A Headquarter Branch B Branch B Teleworker - Set the system address of IP Phone to the IP address of ipldk-60 located in H/Q, Branch A and Branch B 40 LG-Nortel Confidential Information

75 D. ipldk-60 IP Network Configuration Guide Configuration for Carrier s SIP Server In this environment, system functions of ipldk-60 cannot be used by remote SIP Phone. Only the functions provided by SIP server can be operable. > Step 1 : Network connection for Internet access - Setup Router configuration to guarantee QoS for VoIP and IP address : It doesn t matter whether IP address for Router is fixed or not. > Step 2 : Configuration of ipldk-60 The IP address of ipldk-60 system always should be set to Static IP whether Router gives fixed IP or not through DHCP function. So, you have to choose and set the IP address of ipldk-60 within the boundary of DHCP allocation table in Router. > Step 3 : IP Phone configuration Setup system IP of SIP Phone to the address of SIP server. 41 LG-Nortel Confidential Information