Luckylight. 3.0mm (1.2") 8 8 Pure Green Dot Matrix LED Displays Technical Data Sheet. Model No.: KWM-30881XPGB

Transcription

1 3.mm (.") 8 8 Pure Green Dot Matrix LED Displays Technical Data Sheet Model No.: KWM-388XPGB Spec No: W88A/B Rev No: V. Date: May//8 Page: OF 6

2 Features:.inch (3.mm) Matrix height. Colors: Pure Green. Flat package and light weight. Easy assembly. High quality and low cost. High reliable and intensity. Low power requirement. The product itself will remain within RoHS compliant version. Descriptions: The KWM-388 series is a large emitting area (3.mm diameter) LED sources configured in a 64 dots 8*8 matrix array. These devices are made with white dots and black surface. Applications: Audio equipment. Instrument panels. Digitalreadoutdisplay. Device Selection Guide: Model No. Chip Material Face Color Descriptions KWM-388APGB Black Row Anode InGaN KWM-388CPGB Black Row Cathode Spec No: W88A/B Rev No: V. Date: May//8 Page: OF 6

3 Package Dimension: PIN 6 PIN 9 8 [.35] ++PIN PIN 8 4*=8 [.3] Φ3 [ Φ.8] 3 [.6] COL. ROW [.9]± *=8 [.''] 3 [.6] 4 [.946] MODEL.54*=.8 [.] Φ.5 [.] ROW 3 4 KWM-388APGB COL. PIN PIN ROW PIN COL. PIN KWM-388CPGB NOTES: All dimensions are in millimeters (inches) tolerance are ±.5mm (.inch) unless otherwise noted. Spec No: W88A/B Rev No: V. Date: May//8 Page: 3 OF 6

4 Absolute Maximum Ratings at Ta=5 Parameters Symbol Max. Unit Power Dissipation Per Segment PD mw Peak Forward Current Per Segment (/ Duty Cycle,.ms Pulse Width) IFP ma Forward Current Per Segment IF 5 ma Dating Linear From 5.4 ma/ Reverse Voltage VR 5 V Operating Temperature Range Topr -4 to +8 Storage Temperature Range Tstg -4 to +85 Soldering Temperature Tsld 6 for 5 Seconds Electrical Optical Characteristics at Ta=5 Parameters Symbol Min. Typ. Max. Unit Test Condition Luminous Intensity Iv mcd IF=mA (Note ) Peak Emission Wavelength λp nm IF=mA Dominant Wavelength λd nm IF=mA (Note ) Spectral Line Half-Width λ nm IF=mA Forward Voltage VF V IF=mA Reverse Current IR µa VR=5V Notes:. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve.. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No: W88A/B Rev No: V. Date: May//8 Page: 4 OF 6

5 Typical Electrical / Optical Characteristics Curves (5 Ambient Temperature Unless Otherwise Noted) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Spectrum Distribution Ta= Wavelength λp (nm) Luminous Intensity & Ambient Temperature Ambient Temperature Ta ( ) Forward Current IF (ma) Luminous Intensity & Forward Current Relative Luminous Intensity (%) Forward Current & Forward Voltage Ta= Forward Voltage VF (V) Ta=5 f=khz Duty=/ 3 Forward Current IF (ma) Forward Current IF (ma) Forward Current Derating Curve Ambient Temperature Ta ( ) Spec No: W88A/B Rev No: V. Date: May//8 Page: 5 OF 6

6 Please read the following notes before using the datasheets:. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).. Storage. If the package contains a moisture proof bag inside, please don't open the package before using.. Before opening the package, the LEDs should be kept at 3 or less and 8%RH or less..3 The LEDs should be used within a year..4 After opening the package, the LEDs should be kept at 3 or less and 6%RH or less. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 6 for 5 seconds within once in less than the soldering iron capacity 5W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Soldering When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Temperature Soldering Time Soldering Iron 3 Max. 3sec.Max. (one time only) Pre-heat Pre-heat Time Solder Wave Soldering Time Wave Soldering Max. 6 sec. Max. 6 Max. 5sec.Max. Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic failure of the LED. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 6. Caution in ESD Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices equipment and machinery must be properly grounded. Spec No: W88A/B Rev No: V. Date: May//8 Page: 6 OF 6