Configuration Guide KG Encryptor

Transcription

1 Configuration Guide KG Encryptor Written for LMOS August 2013 The purpose of this document is to detail the installation and configuration of an Uplogix Local Managers (LM) to facilitate remote connectivity to a KG Encryptor. Features Supports Encryptors with Uplogix 500 or 5000 Supports Encryptors with Uplogix 5000 with dedicated Ethernet card installed Physical Connection Connect a free serial port on the Uplogix to the s RS-232 console management port with a standard Cat-5 cable and a RJ45-to-DB9 connector. Connect the Uplogix LM s corresponding Ethernet port to the s front-panel-mounted Ethernet Port provided for the Console with a standard Cat-5 cable. NOTE: A dedicated Ethernet connection is required for Ethernet port forwarding. This type of connection is supported in an Uplogix LM 5000 with an installed dedicated Ethernet card. Configuring the Ports To configure the Uplogix LM for connection to a run the command config init and follow the prompts as below: [admin@evalpod2 (port1/4)]# config init --- Enter New Values --- description: make [native]: management IP:

2 Configure dedicated ethernet port? (y/n) [n]: n Serial Bit Rate [9600]: Serial Data Bit [8]: Serial Parity [none]: Serial Stop Bit [1]: Serial Flow Control [none]: Use null modem (rolled cable to device)? (y/n) [n]: Do you want to commit these changes? (y/n): y The default console settings for the are 9600 bit rate, 8 serial data bit, no serial parity, serial stop bit 1, no flow control. To configure the Uplogix LM for connection to a, run the command config init and config protocol forward and follow the prompts as below: [admin@evalpod2 (port1/4)]# config init --- Enter New Values --- description: make [native]: management IP: Configure dedicated ethernet port? (y/n) [n]: y Use DHCP? (y/n) [n]: n Each dedicated port IP address assignment must be on a different network. The device IP assignment and port IP assignment should be on the same network for this port. dedicated device IP: dedicated port IP: dedicated netmask: speed/duplex [auto]: Serial Bit Rate [9600]: Serial Data Bit [8]: Serial Parity [none]: Serial Stop Bit [1]: Serial Flow Control [none]: Use null modem (rolled cable to device)? (y/n) [n]: Do you want to commit these changes? (y/n): y To configure the Uplogix to pass web traffic to the s web interface, run the configure protocol forward command as below and enter dedicated 80 http to set the TCP port to which traffic will be passed on the device s dedicated IP address ( , entered above). [admin@evalpod2 (port1/4)]# config protocol forward [forward]# dedicated 80 http [forward]# exit 2

3 Connecting to the Encryptor To connect to the serial console of the, first connect to the Uplogix LM using SSH, navigate to the port that the is connected to, and use the terminal command. When finished, use ~ <ENTER> to disconnect. [admin@evalpod2]# port 1/4 native [admin@evalpod2 (port1/4)]# terminal Press ~[ENTER] to exit. Connecting... Console session started. Press ~[ENTER] to exit. Console session ended. Disconnecting... The methodology for connecting to the web interface of a varies slightly depending on the SSH client being used. To use the SSH applet in the Uplogix Control Center s GUI, click the CLI button for the Uplogix LM, log in with valid credentials, click Terminal > Forward, click the check box next to the s port, then click Apply. 3

4 Connection to the s web interface can now be achieved by opening a web browser on your workstation and entering :[port] in the address bar, where [port] is the port highlighted in green (6252 in the above example). The port is selected randomly when Apply is pressed, but can also be set manually by entering a port number and pressing apply. For information on connecting with other SSH clients, see the Uplogix feature guide for port forwarding here: 4

5 Receiving technical support The Uplogix technical support website allows you to open support requests, browse the knowledge base and download software updates. You must have a user account to view this site. To create an account, send an to support@uplogix.com with the subject line create account. Include this information: Organization name Account user s address User s general contact information If you need to contact Uplogix customer support, please provide this information: Product model Serial number and software version (use the show version command from the LMOS command line) Phone: Phone: (toll-free) Fax: support@uplogix.com URL: Trademark and copyright information Information in this document is subject to change without notice Uplogix, Inc. All Rights Reserved. Uplogix, the Uplogix logo, and SurgicalRollback are trademarks of Uplogix, Inc. in the United States and other jurisdictions. All other marks referenced are those of their respective owners. 5