OUTDOOR IR NETWORK CAMERA Series
|
|
- Marian Griffin
- 4 years ago
- Views:
Transcription
1 OUTDOOR IR NETWORK CAMERA Series INSTALLATION GUIDE Please read instructions thoroughly before operation and retain it for future reference.
2 1. OVERVIEW 1.1 Package Content Network camera Installation Sticker Installation Guide RJ45 cable extender adapter Ground Wire CD-ROM disc (including user manuals & CMS software Video Viewer ) 1.2 Dimensions Cable Overview CABLE RJ45 network cable Reset wires Power wires DESCRIPTION Connect it to the supplied RJ45 cable extender adapter for cable extension, and prepare another RJ45 network cable with suitable length for your connection. Remove the insulating coating of these two wires, and twist them together to reset default. This will reset all parameters, including the IP address to factory default settings. Note: Disconnect power before twisting these two wires together, and connect to power again for reset default. When the reset is done, disconnect these two wires. Connect to AC power supply. For details, please refer to 2.2 Connect to power at page 3. 1
3 2. INSTALLATION & CONNECTION 2.1 Install the Camera Note: The illustration below is for installation only, and the actual product may look different from the illustration below. 2
4 2.2 Connect to power Get a power cord and cut off its female connector side. Then, remove the insulating coating to reveal positive, negative and ground wires. Find the two wires labeled AC+ (red) & AC- (black) on your camera, and remove a small piece of their insulating coating to reveal the naked wires. 3
5 Twist the camera s and power cord s wires together according to the corresponding electrodes (positive to positive, negative to negative, disregarding the ground wire). Then, use the insulation tape to cover the connected wires. 4
6 3. ETHERNET CONNECTION Before using this network camera, please follow the instructions below to finish the network connection settings based on your installation environment: To configure the network settings, you must connect the camera to your PC by LAN. For details, please refer to 3.1 Network Connection via LAN at page 5. To configure the network settings via Wizard, please refer to 3.2 Network Configurations via Wizard at page 9. To configure the network settings via our supplied CMS software, Video Viewer, please refer to 3.3 Network Configurations via Video Viewer at page Network Connection via LAN Step1: Connect this network camera and your PC via a RJ45 network cable, and make sure the camera is powered on. Step2: Set the PC s IP address as XXX (1~255, except 10). For Windows 2000 users: a) Select Start Settings Network and Dial-up Connections. b) Right-click on Local Area Connection, and select Properties. c) In the General tab, select Internet Protocol (TCP/IP), and select Properties. 5
7 d) In the General tab, select Use the following IP address, and set the IP address as described below. Note: It s recommended to note down the current settings first and then change as instructed. It s helpful when you need to restore the PC network settings for connecting to Internet later. e) Click OK to close the Internet Protocol (TCP/IP) Properties dialog box. Then, click Close to close the Local Area Connection Properties dialog box. For Windows XP users: a) Select start All Programs Control Panel Network and Internet Connections Network Connections (If you re in Category View ). 6
8 b) In LAN or High-Speed Internet, right-click on Local Area Connection, and select Properties. c) In the General tab, select Internet Protocol (TCP/IP), and select Properties. d) In the General tab, select Use the following IP address, and set the IP address to XXX (XXX can be any value from 1~255 except 10). Note: It s recommended to note down the current settings first and then change as instructed. It s helpful when you need to restore the PC network settings for connecting to Internet later. e) Click OK to close the Internet Protocol (TCP/IP) Properties dialog box. Then, click Close to close the Local Area Connection Properties dialog box. For Windows Vista users: a) Select (start) Control Panel Network and Internet to enter the Network and Sharing Center. Then, click Manage network connections (If you re in Category View ). b) Right-click on Local Area Connection, and select Properties. c) In the General tab, select Internet Protocol Version 4 (TCP/IPv4), and select Properties. 7
9 d) In the General tab, select Use the following IP address, and set the IP address as described below. Note: It s recommended to note down the current settings first and then change as instructed. It s helpful when you need to restore the PC network settings for connecting to Internet later. e) Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box. Then, click Close to close the Local Area Connection Properties dialog box. 8
10 3.2 Network Configurations via Wizard A quick installation wizard is available via your web browser for password change, date & time settings, and network configurations. For details about the wizard, please refer to Setting in Wizard at page 9. For details about DDNS setting for PPPoE and DHCP, please refer to DDNS Setting at page 11. Note: You can also change the settings in the system configuration page via your web browser later. For details, please refer to 5. ACCESSING THE CAMERA VIA WEB BROWSER in the user manual Setting in Wizard Step1: Open your web browser, for example, Microsoft Internet Explorer, and enter in the URL address box. Step2: In the login page, key in the default user name (admin) and password (admin), and enter the security code from the image below. Then, click LOGIN. Step3: The wizard is then starting analyzing your network environment, and shows your network environment. Select Next to continue. Step4: In Account, change the access password if needed. If not, leave all the columns blank, and select Next. 9
11 Step5: In Date and Time, check if the date and time setting are correct and modify if necessary. Step6: In Network, select the network type based on your network environment (Static IP / PPPoE / DHCP), and key in the information needed. Note: This camera doesn t support POE router or hub. For Static IP: a) Enter the information of Server IP, Gateway and Net Mask obtained from your ISP (Internet Service Provider). b) Enter the port number. The valid number ranges from 1 to The default value is 80. Typically, the TCP port used by HTTP is 80. However in some cases, it is better to change this port number for added flexibility or security. For PPPOE: a) Enter the user name and password obtained from your ISP. b) Continue the DDNS setting as instructed in DDNS Setting when you re prompted to restart the web browser in Step8. 10
12 For DHCP: a) Before selecting this option, you need to finish the DHCP router settings first. Get a router and connect it to the Internet via your PC (with Static IP or PPPoE setting). There are different setting methods for different routers. Please refer to their respective user manuals. b) Continue the DDNS setting as instructed in DDNS Setting when you re prompted to restart the web browser in Step8. Step7: In Apply, all the changes are listed. Check if the changes are correct. If yes, click Save. If no, click Back to where the changes should be made for modification, and click Save to apply the settings. Note: You can also change the settings in the system configuration page via your web browser later. For details, please refer to 5. ACCESSING THE CAMERA VIA WEB BROWSER in the user manual. Step8: You will be prompted to restart your web browser for network setting changes. For PPPoE and DHCP, continue as instructed in DDNS Setting. For Static IP, disconnect your camera and your PC, and connect them to Internet separately. Next, enter the IP address of the camera in the URL address box of the web browser, and see if you can access the camera successfully DDNS Setting Step1: Re-log in the network camera, and select Close for network environment checking. Step2: In the live page, click Configuration to open the configuration page. 11
13 Step3: Click Network DDNS, and check DDNS Enable. Step4: Select default in System Name. In Hostname, keep the default value, i.e. the MAC address of this camera, or change the name to a meaningful one. It s easier to memorize. Then, note down the whole address of the camera, for example, MAC000E530D93E3.ddns.dvrtw.com.tw. Note: You can also create a DDNS account from a website which provides free DDNS service. For details, please refer to APPENDIX CREATING AN ACCOUNT FOR DDNS SERVICE at page 17. Step5: Click Save and log out. Then, disconnect your camera and your PC, and connect them to Internet separately. Step6: Enter the host name you just note down in the URL address box of the web browser, and see if you can access the camera successfully. 12
14 3.3 Network Configurations via Video Viewer Install the software Step1: Place the supplied CD into your CD-ROM or DVD-ROM drive. The program will be automatically run. Step2: Click Program in the Video Viewer section to install Video Viewer, or click Download The Latest Version under Program to download the latest version of Video Viewer from the Internet (if your PC is connected to Internet). Step3: Follow the on-screen instructions to finish the installation. When the installation is completed, a shortcut icon will be placed on your PC desktop. Step3: Double-click on your PC desktop to open Video Viewer and enter the control panel. By defaults, the Address Book panel will be displayed on the right side of the control panel. Step4: Click to key in the default IP address, user name, password, and port number of the camera you intend to connect. The default values are as follows: Item Default Value IP address User name admin Password admin Port 80 OR Click to search the available IP address(es) of other camera(s) under the same domain as your PC s IP address. The found address(es) will be listed, and can be added into the address book by clicking. Step5: Double-click the IP address you just added into the address book to log in Network Setting Note: It s recommended to have the qualified installer to plan and configure the network setting. Step1: Click to show the General setting and utilities dialog box, and click Remote Config twice to enter the camera setting page. 13
15 Step2: Select Network to make network settings based on your network environment. There are three network connection types: Static IP, PPPOE, and DHCP. Note: This camera doesn t support POE router or hub. For Static IP: a) Enter the information of Server IP, Gateway and NetMask obtained from your ISP (Internet Service Provider). b) Enter the port number. The valid number ranges from 1 to The default value is 80. Typically, the TCP port used by HTTP is 80. However in some cases, it is better to change this port number for added flexibility or security. c) Click Apply, and click OK to exit the setting page. For PPPOE: a) Go to Network DDNS, and select default in the System Name drop-down list. b) In Hostname, keep the default value, i.e. the MAC address of this camera, or change the name to a meaningful one. It s easier to memorize. c) Note down the whole address of the camera, for example, MAC000E ddns.dvrtw.com.tw. Note: You can also create a DDNS account from a website which provides free DDNS service. For details, please refer to APPENDIX CREATING AN ACCOUNT FOR DDNS SERVICE at page 17. d) Go to Network and select PPPOE. Then, enter the user name and password obtained from your ISP. 14
16 e) Click Apply, and click OK to exit the setting page. For DHCP: a) Finish the DHCP router setting. Get a router and connect it to the Internet via your PC (with Static IP or PPPoE setting). There are different setting methods for different routers. Please refer to their respective user manuals. b) Go to Network DDNS, and select default in the System Name drop-down list. c) In Hostname, keep the default value, i.e. the MAC address of this camera, or change the name to a meaningful one. It s easier to memorize. d) Note down the whole address of the camera, for example, MAC000E ddns.dvrtw.com.tw. Note: You can also create a DDNS account from a website which provides free DDNS service. For details, please refer to APPENDIX CREATING AN ACCOUNT FOR DDNS SERVICE at page 17. e) Go to Network and select DHCP. 15
17 f) Click Apply, and click OK to exit the setting page. Step3: Disconnect your camera and your PC, and connect them to Internet separately. Step4: Add the IP address or host name of your camera in of Video Viewer with correct user name and password, and click it twice to see if you can access to your camera Change the password It s recommended to change the default password for the first time usage in case of any unauthorized access. Step1: Click to show the General setting and utilities dialog box, and click Remote Config twice to enter the camera setting page. Step2: Click General Account, and select the default account. Change the password directly, and click Apply. Step3: Return to the live view, and click to disconnect the camera. Step4: Click to select the IP address of the camera, and click to enter the setting page and modify the password. Then, click Login to access the camera with the new password. 16
18 APPENDIX CREATING AN ACCOUNT FOR DDNS SERVICE For PPPOE or DHCP, you should enter the host name which points to the IP address of your network camera for login first. Besides using the default DDNS service, you can also apply for new DNS services. There are many websites for free DDNS service application, and below shows an example of DDNS account application from the website Step1: Go to and click Create Account to sign up a DDNS account. Step2: Enter all the information necessary for signing up an account according to the website instructions. Key in a user name for login, for example, headoffice523. Set the password and input it again to confirm. Key in your address and input it again to confirm. Then, click Create Account. Step3: The system will automatically send a confirmation to your account. Please read this within 48 hours and complete the procedure to activate your 17
19 account according to the instructions in the . When the account is confirmed, you will see Account Confirmed. Your account is created successfully now. Step4: Click login, and enter the user name and password you preset before to log in. Step5: Click Add Host Services. Input a meaningful host name. Choose a host name. Enter the IP address you want to redirect. Note down the whole host name, for example, headoffice523.dyndns.org. Then, click Add To Cart for billing. Note: This service is free. Just finish the billing process, and NO paying information is required. Step6: Click Activate Services after checkout, and you re ready to use DDNS services now. 18
20 Step7: Return to Video Viewer, and go to Network DDNS. Select On for DDNS. Select the system name you set when subscribing the DDNS service from the drop-down list, for example, dyndns. Enter the user name & password you used to log into the DDNS service. Enter the host name you set when subscribing the DDNS service, for example, headoffice
How To Set Up A Network Camera On A Network Cable Extender (Rj45) With A Network Cam (Cms) On A Pc Or Mac) With An Ipad Or Ipad (For Awn) With The Power Cable (
OUTDOOR IR NETWORK CAMERA SERIES Installation Guide Please read instructions thoroughly before operation and retain it for future reference. TABLE OF CONTENTS 1. OVERVIEW... 1 1.1 Package Content... 1
NETWORK SETUP INSTRUCTIONS
NETWORK SETUP INSTRUCTIONS How to Connect AVTECH Product to Internet To connect AVTECH DVR or network camera to Internet, you need to: 1). Figure out your network environment, and have related IP information
1CH VIDEO SERVER INSTALLATION GUIDE. Please read instructions thoroughly before operation and retain it for future reference.
314Z 1CH VIDEO SERVER INSTALLATION GUIDE Please read instructions thoroughly before operation and retain it for future reference. x931_931a_v1.1 314Z 1CH VIDEO SERVER INSTALLATION GUIDE Please read instructions
Easy Setup Guide for the Sony Network Camera
-878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer
Network Setup Guide. 1 Glossary. 2 Operation. 1.1 Static IP. 1.2 Point-to-Point Protocol over Ethernet (PPPoE)
Network Setup Guide 1 Glossary 1.1 Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means
1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
Check Your Package Contents. CD-ROM containing Manual and Warranty
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVA-G3340S Wireless VoIP Router Before You Begin If you purchased this Router to share your
USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
Connecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
Installation. The product model shown in this QIG is TD-W8961ND, as an example.
Installation The product model shown in this QIG is TD-W8961ND, as an example. Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s)
NETWORK SETUP GLOSSARY
GLOSSARY NETWORK SETUP Static IP PPPoE DHCP DDNS Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service
Quick Installation Guide
V48.01 Model: FI8919W Quick Installation Guide Outdoor Pan/Tilt Wireless IP Camera For Windows OS ------- Page 1 For MAC OS ------- Page 15 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation
You may refer the Quick Installation Guide in the package box for more information.
Hardware Installation: 1. Turn off your modem. 2. Use one Ethernet cable to connect your modem to WAN port (Blue) port of BR-6228nC. 3. Use another Ethernet cable to connect your PC to one LAN Port (Yellow)
Turn off all of your network devices, including your computer, Modem and the Router.
Note Please use only wired network connections to configure the Router. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
Turn off all of your network devices, including your computer, Modem and the Router.
Note The product model shown in this part is TL-R460, as an example. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
1.3 MEGAPIXEL WIRELESS NETWORK CAMERA SERIES
1.3 MEGAPIXEL WIRELESS NETWORK CAMERA SERIES ADVANCED NETWORK SETUP Please read instructions thoroughly before operation and retain it for future reference. n812_813_network_v1.3 IMPORTANT SAFEGUARD All
Chapter 2 Preparing Your Network
Chapter 2 Preparing Your Network This document describes how to prepare your network to connect to the Internet through a router and how to verify the readiness of your broadband Internet service from
Please use only wired network connections to configure the router.
Note Please use only wired network connections to configure the router. Connect the WAN port on your Router to the Modem s LAN port with an Ethernet cable. Note If connecting the TL-WR543G to the WISP
Quick Installation Guide
V2.01 Wired Camera Quick Installation Guide (For Windows OS) FI8620 ShenZhen Foscam Intelligent Technology Co., Ltd Packing List Quick Installation Guide FI8620 Quick Installation Guide 1) IP CAMERA X
How to Remotely View Security Cameras Using the Internet
How to Remotely View Security Cameras Using the Internet Introduction: The ability to remotely view security cameras is one of the most useful features of your EZWatch Pro system. It provides the ability
DVG-2101SP VoIP Telephone Adapter
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVG-2101SP VoIP Telephone Adapter Before You Begin 1. If you purchased this VoIP Telephone
If no telephone is needed, please connect the LINE port of the Modem Router to the wall jack using the telephone line directly.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
DSL Installation Guide
DSL Installation Guide Thank you for choosing Integra Telecom s DSL service! Introduction This guide will walk you through the DSL installation process and will help you configure a computer to access
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This
Installation. Note Please use only wired network connections to configure the router.
Installation Note Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s) and the Modem Router. If you currently use a modem,
Quick Installation Guide
Model: FI8905E Quick Installation Guide Ourdoor POE Network Camera For Windows OS ------- Page 1 For MAC OS ------- Page 14 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation Guide - For
Installation. Note The product model shown in this QIG is TD-W8951ND, as an example.
Installation The product model shown in this QIG is TD-W8951ND, as an example. Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s)
Wireless G Broadband quick install
Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install
Broadband Router ALL1294B
Broadband Router ALL1294B Broadband Internet Access 4-Port Switching Hub User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Broadband Router Features... 1 Package Contents... 3 Physical Details...
P-660R-T1/T3 v2 Quick Start Guide
P-660R-T1/T3 v2 ADSL2+ Access Router Quick Start Guide Version 3.40 Edition 1 12/2006 0 Overview P-660R-T1/T3 v2 Quick Start Guide This Quick Start Guide shows you how to: 1 Connect the Hardware 2 Set
Please use only wired network connections to configure the Router.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
SOHO 6 Wireless Installation Procedure Windows 95/98/ME with Internet Explorer 5.x & 6.0
SOHO 6 Wireless Installation Procedure Windows 95/98/ME with Internet Explorer 5.x & 6.0 Before You Begin Before you install the SOHO 6 Wireless, you must have: A computer with a 10/100BaseT Ethernet card
Installation. The product model shown in this QIG is TD-W8951ND, as an example.
Installation Note The product model shown in this QIG is TD-W8951ND, as an example. Note Please use only wired network connections to configure the Router. Before cable connection, keep your hands dry.
Note The product model shown in this QIG is TD-8817, as an example.
Note The product model shown in this QIG is TD-8817, as an example. Turn off all of your network devices, including your computer and the Modem Router. If you currently use a modem, disconnect it now -
LevelOne. User Manual. FBR-1430 VPN Broadband Router, 1W 4L V1.0
LevelOne FBR-1430 VPN Broadband Router, 1W 4L User Manual V1.0 Table of Contents CHAPTER 1 INTRODUCTION... 1 VPN BROADBAND ROUTER FEATURES... 1 Internet Access Features... 1 Advanced Internet Functions...
EnGenius ERB9250 300M Range Extender. Quick Start Guide
EnGenius ERB9250 300M Range Extender Quick Start Guide Package Contents One ERB9250 300M Range Extender One 12V/1A power adapter Two 2dBi 2.4GHz SMA antennas One Ethernet cable One CD-ROM with user s manual
TW100-BRV204 VPN Firewall Router
TW100-BRV204 VPN Firewall Router Cable/DSL Internet Access 4-Port Switching Hub User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 TW100-BRV204 Features... 1 Package Contents... 3 Physical Details...
Quick Installation Guide DAP-1360. Wireless N 300 Access Point & Router
DAP-1360 Wireless N 300 Access Point & Router BEFORE YOU BEGIN Delivery Package Access point DAP-1360 Power adapter DC 12V Ethernet cable (CAT 5E) (brochure). If any of the items are missing, please contact
FI8910W Quick Installation Guide. Indoor MJPEG Pan/Tilt Wireless IP Camera
Model: FI8910W Quick Installation Guide (For Windows OS) (For MAC OS please go to page 17) Indoor MJPEG Pan/Tilt Wireless IP Camera Black White Package Contents IP Camera FI8910W with IR-Cut.x 1 DC Power
NetLINE Wireless Broadband Gateway
NetLINE Setup Guide Farallon s NetLINE connects to your cable/dsl modem, allowing computers on your local wired and wireless networks to share a single broadband connection to the Internet. This Setup
Installation. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem.
Installation Note Please use only wired network connections to configure the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your
Assign a static IP address (192.168.1.100) for your computer. Please refer to T3 in Troubleshooting guide on page 10 if you need assistance.
Assign a static IP address (192.168.1.100) for your computer. Please refer to T3 in Troubleshooting guide on page 10 if you need assistance. You may need to write down the original settings as a backup.
your Gateway Windows network installationguide 802.11b wireless series Router model WBR-100 Configuring Installing
your Gateway Windows network installationguide 802.11b wireless series Router model WBR-100 Installing Configuring Contents 1 Introduction...................................................... 1 Features...........................................................
Linksys E2000 Wireless-N Router Configuration Guide
Linksys E2000 Wireless-N Router Configuration Guide Revision 1.1 Copyright 2012 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 rd Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron
Model:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router
Quick Installation Guide Model:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router 1.Connecting the device Note: Please use wired network connections only to configure the Router. 1 Connect the WAN port
Quick Installation Guide
Quick Installation Guide (For Windows & Mac OS) Outdoor Wireless IP Camera Package Contents V1.1 IP Camera Power Adapter Resource CD Ethernet Cable Mounting Bracket(except FI8919) Wi-Fi Antenna Quick Installation
Preparing the Computers for TCP/IP Networking
Configuration Preparing the Computers for TCP/IP Networking Configuring Windows 98, and ME for TCP/IP Networking Verifying TCP/IP Properties Configuring Windows 2000 or XP for IP Networking Install or
TW100-BRF114 Firewall Router. User's Guide. Cable/DSL Internet Access. 4-Port Switching Hub
TW100-BRF114 Firewall Router Cable/DSL Internet Access 4-Port Switching Hub User's Guide Table of Contents CHAPTER 1 INTRODUCTION...1 TW100-BRF114 Features...1 Package Contents...3 Physical Details...
ASUS WL-5XX Series Wireless Router Internet Configuration. User s Guide
ASUS WL-5XX Series Wireless Router Internet Configuration User s Guide Contents Chapter 1 Introduction:...1 Chapter 2 Connecting the wireless router...1 Chapter 3 Getting to know your Internet connection
LabelWriter. Print Server. User Guide
LabelWriter Print Server User Guide Copyright 2010 Sanford, L.P. All rights reserved. 08/10 No part of this document or the software may be reproduced or transmitted in any form or by any means or translated
NETWORK SETUP GLOSSARY
GLOSSARY NETWORK SETUP Static IP Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means
Contents. Section A Networking Basics... 1. 1 Learning the Basics... 3. Section B Wired Ethernet Networking... 17
Contents Section A Networking Basics...................................... 1 1 Learning the Basics............................................. 3 Selecting a network connection........................................
Turn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes.
Connect to the Access Point with the Ethernet cable or via wireless. The default SSID of the Access Point is TP-LINK_ XXXXXX. The XXXXXX is the last 6 characters of the Access Point s MAC address. Plug
NETWORK SET UP GUIDE FOR RVH1004/US411 RVH1008/US811 RVH1016/US611. 1 st G/2 nd G/3 rd G UGI H.264 DVR. SUPPORTING ROUTER DLINK LINKSYS NETGEAR Belkin
NETWORK SET UP GUIDE FOR RVH1004/US411 RVH1008/US811 RVH1016/US611 1 st G/2 nd G/3 rd G UGI H.264 DVR SUPPORTING ROUTER DLINK LINKSYS NETGEAR Belkin Network Setup- p1 Introduction Thank you for purchasing
Prestige 660R-6x Read Me First
Prestige 660R-6x Read Me First Prestige Rear Panel Connections DSL PORT CONNECTION Connect the DSL port on the Prestige to the wall jack using the included DSL cable (telephone wire). Connect the micro
DSL-G604T Wireless ADSL Router
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DSL-G604T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share
Aolynk DR814Q ADSL2+ Broadband Router Quick Start
Aolynk DR814Q ADSL2+ Broadband Router 1 Packing List Quick Start Unpack the shipping carton carefully and check the following items listed below: One Aolynk DR814Q ADSL2+ Broadband Router One power adapter
Access the GV-IP Camera through a broadband modem
Access the GV-IP Camera through a broadband modem Applied to All GV-IP Cameras Article ID: GV15-12-03-26 Release Date: 03/26/2012 Introduction The document introduces how to connect your GV-IP Camera to
Network Setup Guide. Introduction. Setting up for use over LAN
Network Setup Guide This manual contains the setup information required to use the machine over wired LAN. If you use the machine with USB connection, refer to your setup sheet. Introduction To use the
SATO Network Interface Card Configuration Instructions
SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless
Internet for Everyone In-Room Instructions January 2011 Version 1.3
Internet for Everyone In-Room Instructions January 2011 Version 1.3 Everywhere Internet 2006 Page 1 of 17 Connecting your computer to the Everywhere Internet network in your room 1. You need a network
User s Manual. Copyright 2010 Vantec Thermal Technologies. All Rights Reserved.
Copyright 2010 Vantec Thermal Technologies. All Rights Reserved. User s Manual Package Contents: 1 NextStar FX Gigabit NAS Adapter x1 2 AC Adapter x1 3 Installation Guide x1 4 Rubber Feet x4 5 User s CD
Chapter 1 Installing the Gateway
Chapter 1 Installing the Gateway This chapter describes how to set up the wireless voice gateway on your Local Area Network (LAN), connect to the Internet, and perform basic configuration. For information
Symphony Network Troubleshooting
Symphony Network Troubleshooting Step 1) Review the Networking 101 presentation on the CD included with the Symphony. A basic understanding of networks is essential to this procedure. Step 2) Identify
2 Setting Up the Hardware for a Wired Ethernet Network... 13. 3 Setting Up the Software for an Ethernet Network... 21
Contents 1 Networking Basics............................................... 1 Selecting a network connection........................................ 2 Wired Ethernet network...........................................
BabyWare Imperial PC Software
Overview (see page 1) Things You Should Know (see page 1) Getting Started (see page 2) Licenses and Registration (see page 6) Usernames Passwords and Login (see page 7) BabyWare Imperial PC Software Overview
Quick Installation Guide DSL-2750U/NRU. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2750U/NRU 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U/NRU Power adapter RJ-11 telephone cable Straight-through Ethernet cable (CAT 5E)
Self Help Guide IMPORTANT! Configuring Your Router With Your Modem. Please read the following carefully; This Guide refers to the following Products:
IMPORTANT! This Guide refers to the following Products: Configuring Your Router With Your Modem Please read the following carefully; Synopsis: A standard (Wireless) Router does not come equipped with the
Point to Point Broadband Internet Service Business
Point to Point Broadband Internet Service Business [Type the company name] USER GUIDE VERSION 1.012010 [Type the document subtitle] Table of Contents Welcome to Point to Point Broadband!... 2 Disclaimer.
Prestige 314 Read Me First
Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER
Wireless Router Setup Manual
Wireless Router Setup Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10082-02 2006-04 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear,
3.5 EXTERNAL NETWORK HDD. User s Manual
3.5 EXTERNAL NETWORK HDD User s Manual Table of Content Before You Use Key Features H/W Installation Illustration of Product LED Definition NETWORK HDD Assembly Setup the Network HDD Home Disk Utility
Internet Access to a DVR365
Configuration Details : Internet Access to DVR365 Page : 1 Internet Access to a DVR365 These instructions will show you how to connect your DVR365 to the internet via an ADSL broadband modem/router. The
ACT High Speed WiMAX Internet
ACT High Speed WiMAX Internet Internet Configuration Manual This manual walks you through the steps of configuring your computer for High Speed WiMAX Internet service with Windows 7, Vista, XP, 2000, And
AgGPS 542 Receiver: Enable GLONASS through the Web Browser
15 April 2011 AgGPS 542 Receiver: Enable GLONASS through the Web Browser This document describes how to use the web browser to enable GLONASS on a Trimble AgGPS 542 receiver. Note: Some AgGPS 542 receivers
Quick Installation Guide DSL-2640U. Wireless N 150 ADSL2+ Modem Router
DSL-2640U Wireless N 150 ADSL2+ Modem Router BEFORE YOU BEGIN Delivery Package Wireless router DSL-2640U Power adapter DC 12V/0.5A RJ-11 telephone cable Straight-through Ethernet cable (CAT 5E) Splitter
Router Setup Manual. NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10060-01 2006-03-17
NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10060-01 2006-03-17 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows,
Chapter 1 Configuring Basic Connectivity
Chapter 1 Configuring Basic Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration
How to configure DVR and computer for running Remote Viewer via IP network
How to configure DVR and computer for running Remote Viewer via IP network Follow these steps to configure a network DVR and a computer with Remote Viewer software to see live pictures via IP network.
DI-634M. Check Your Package Contents. This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 7.
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 7. DI-634M 108G MIMO Wireless Router Before You Begin 1. If you purchased this router to share
User Manual. Onsight Management Suite Version 5.1. Another Innovation by Librestream
User Manual Onsight Management Suite Version 5.1 Another Innovation by Librestream Doc #: 400075-06 May 2012 Information in this document is subject to change without notice. Reproduction in any manner
Software Installation Guide
Software Installation Guide This manual explains how to install the software over a USB or network connection. Network connection is not available for models SP 200/200S/203S/203SF/204SF. To manually configure
Omni 56K USB Lite Quick Start Guide
Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack
CPEi 800/825 Series. User Manual. * Please see the Introduction Section
CPEi 800/825 Series User Manual * Please see the Introduction Section Contents Introduction...iii Chapter 1: CPEi 800/825 User Guide Overview... 1-1 Powerful Features in a Single Unit... 1-2 Front of the
Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2
Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface
Networking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples
Networking General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication
Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
Note The product model shown in this QIG is TL-WA701ND, as an example. Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
exacqvision IP Camera Quickstart Guide
exacqvision IP Camera Quickstart Guide 11955 Exit 5 Pkwy Building 3 Fishers, IN 46037-7939 USA +1.317.845.5710 phone +1.317.845.5720 fax The exacqvision NVR software is full-featured network video surveillance
Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance. Connect to the Access Point with the Ethernet cable or via wireless.the
Quick Installation Guide
Wired/Wireless IP Camera Quick Installation Guide Model: AJ-C2WA-C118 0 Step 1: Hardware Installation 1. Install the Wi-Fi antenna. 2. Plug the power adaptor into camera. 3. Plug the network cable into
NETWORK SET UP GUIDE FOR
NETWORK SET UP GUIDE FOR USZ11ZS USX21ZS USX31ZAND DVRX16D DVRX32D HDDX13D SUPPORTING ROUTER D-Link Linksys NETGEAR BELKI IP Addresses on the Internet When you connect to the Internet, through dialup connection,
Internet Broadband Router XRT-501. Quick Installation Guide
Internet Broadband Router XRT-501 Quick Installation Guide Table of Contents 1. Requirements... 3 2. Before Startup... 3 2.1 Physical Installation... 3 2.2 Configuration... 4 3. Quick Installation... 5
Quick-Start Guide 007-SE01-001. Gigaset. Residential Wireless Gateway SE567/SE568. Gigaset Communications GmbH is a trademark licensee of Siemens AG
Quick-Start Guide 007-SE01-001 Gigaset Residential Wireless Gateway SE567/SE568 Gigaset Communications GmbH is a trademark licensee of Siemens AG Before you begin... Verify that the following items came
Static Business Class HSI Basic Installation NETGEAR 7550
Static Business Class HSI Basic Installation Table of Contents Multiple LAN Support... 3 Full BHSI Install Summary... 7 Physical Connections... 8 Auto Configuration... 9 Auto Configuration... 9 Gateway
Adding or replacing a mesh node in an existing mesh network
Adding or replacing a mesh node in an existing mesh network Use this procedure to add or replace a in an existing mesh For this procedure to work all nodes running the same firmware version. Before you
Prestige 650R-31/33 Read Me First
Prestige 650R-31/33 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on
HW550-3G. 3G Mobile Broadband plus 4-Port Wireless-N Router
HW550-3G 3G Mobile Broadband plus 4-Port Wireless-N Router Table of Contents About the Product...4 Features...5 Requirements...6 Package Content...7 Device Design...8 Getting Started...11 Plan Your Network...12
Networking Guide Redwood Manager 3.0 August 2013
Networking Guide Redwood Manager 3.0 August 2013 Table of Contents 1 Introduction... 3 1.1 IP Addresses... 3 1.1.1 Static vs. DHCP... 3 1.2 Required Ports... 4 2 Adding the Redwood Engine to the Network...
Print Server Application Guide. This guide applies to the following models.
Print Server Application Guide This guide applies to the following models. TL-WR842ND TL-WR1042ND TL-WR1043ND TL-WR2543ND TL-WDR4300 CONTENTS Chapter 1. Overview... 1 Chapter 2. Before Installation...
STATIC IP SET UP GUIDE
STATIC IP SET UP GUIDE VERIZON D-LINK 2750B & ACTIONTEC GT784 WNV WIRELESS GATEWAY Verizon High Speed Internet for Business Verizon High Speed Internet for Business YOUR NEW STATIC IP CONNECTION AND SET