MC78XX/LM78XX/MC78XXA
|
|
- Jack Johnson
- 7 years ago
- Views:
Transcription
1 3-Terminal 1A Positive oltage Regulator Features Output Current up to 1A Output oltages of 5, 6, 8, 9, 10, 12, 15, 18, 24 Thermal Overload Protection Short Circuit Protection Output Transistor Safe Operating Area Protection Description The MC78XX/LM78XX/MC78XXA series of three terminal positive regulators are available in the TO-220/D-PAK package and with several fixed output voltages, making them useful in a wide range of applications. Each type employs internal current limiting, thermal shut down and safe operating area protection, making it essentially indestructible. If adequate heat sinking is provided, they can deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltages and currents. TO D-PAK 1 1. Input 2. GND 3. Output Internal Block Digram Rev Fairchild Semiconductor Corporation
2 Absolute Maximum Ratings Parameter Symbol alue Unit Input oltage (for O = 5 to 18) (for O = 24) Thermal Resistance Junction-Cases (TO-220) RθJC 5 o C/W Thermal Resistance Junction-Air (TO-220) RθJA 65 o C/W Operating Temperature Range TOPR 0 ~ +125 o C Storage Temperature Range TSTG -65 ~ +150 o C I I Electrical Characteristics (MC7805/LM7805) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I = 10, CI= 0.33µF, CO= 0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ=+25 o C MC7805/LM7805 Min. Typ. Max. TJ =+25 o C mA Io 1.0A, PO 15W I = 7 to O = 7 to I = 8 to IO = 5.0mA to1.5a Load Regulation (Note1) Regload TJ=+25 o C IO =250mA to mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I= 7 to ma Output oltage Drift O/ T IO= 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA=+25 o C µ/o f = 120Hz O = 8 to db Dropout oltage Drop IO = 1A, TJ =+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA =+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in o due to heating effects must be taken 2
3 Electrical Characteristics (MC7806) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =11, CI= 0.33µF, CO= 0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7806 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 8.0 to I = 8 to I = 9 to Load Regulation (Note1) Regload TJ =+25 o IO =5mA to 1.5A C IO =250mA to750a Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1A I = 8 to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz I = 9 to db Dropout oltage Drop IO = 1A, TJ =+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA=+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 3
4 Electrical Characteristics (MC7808) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =14, CI= 0.33µF, CO= 0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7808 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 10.5 to I = 10.5 to I = 11.5 to Load Regulation (Note1) Regload TJ =+25 o IO = 5.0mA to 1.5A C IO= 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 10.5A to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz, I= 11.5 to db Dropout oltage Drop IO = 1A, TJ=+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 4
5 Electrical Characteristics (MC7809) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =15, CI= 0.33µF, CO= 0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ=+25 C MC7809 Min. Typ. Max. TJ =+25 C mA IO 1.0A, PO 15W I= 11.5 to I = 11.5 to I = 12 to IO = 5mA to 1.5A Load Regulation (Note1) Regload TJ=+25 C IO = 250mA to 750mA Quiescent Current IQ TJ=+25 C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 11.5 to ma Output oltage Drift O/ T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 C µ/o f = 120Hz I = 13 to db Dropout oltage Drop IO = 1A, TJ=+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ= +25 C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 5
6 Electrical Characteristics (MC7810) (Refer to test circuit,0 C< TJ < 125 C, IO = 500mA, I =16, CI= 0.33µF, CO=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 C MC7810 Min. Typ. Max. TJ =+25 C mA IO 1.0A, PO 15W I = 12.5 to I = 12.5 to I = 13 to IO = 5mA to 1.5A Load Regulation (Note1) Regload TJ =+25 C IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 12.5 to ma Output oltage Drift O/ T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 C µ/o f = 120Hz I = 13 to db Dropout oltage Drop IO = 1A, TJ=+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA=+25 C ma Peak Current IPK TJ =+25 C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 6
7 Electrical Characteristics (MC7812) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =19, CI= 0.33µF, CO=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7812 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 14.5 to I = 14.5 to I = 16 to Load Regulation (Note1) Regload TJ =+25 o IO = 5mA to 1.5A C IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 14.5 to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz I = 15 to db Dropout oltage Drop IO = 1A, TJ=+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA=+25 o C ma Peak Current IPK TJ = +25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 7
8 Electrical Characteristics (MC7815) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =23, CI= 0.33µF, CO=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7815 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 17.5 to I = 17.5 to I = 20 to IO = 5mA to 1.5A Load Regulation (Note1) Regload TJ =+25 o C IO = 250mA to mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 17.5 to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz I = 18.5 to db Dropout oltage Drop IO = 1A, TJ=+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA=+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 8
9 Electrical Characteristics (MC7818) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =27, CI= 0.33µF, CO=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7818 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 21 to I = 21 to I = 24 to Load Regulation (Note1) Regload TJ =+25 o IO = 5mA to 1.5A C IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 21 to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz I = 22 to db Dropout oltage Drop IO = 1A, TJ=+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA=+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 9
10 Electrical Characteristics (MC7824) (Refer to test circuit,0 C < TJ < 125 C, IO = 500mA, I =33, CI= 0.33µF, CO=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions O Line Regulation (Note1) Regline TJ =+25 o C MC7824 Min. Typ. Max. TJ =+25 o C mA IO 1.0A, PO 15W I = 27 to I = 27 to I = 30 to Load Regulation (Note1) Regload TJ =+25 o IO = 5mA to 1.5A C IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma Quiescent Current Change IQ IO = 5mA to 1.0A I = 27 to ma Output oltage Drift O/ T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz, TA =+25 o C µ/o f = 120Hz I = 28 to db Dropout oltage Drop IO = 1A, TJ=+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I = 35, TA=+25 o C ma Peak Current IPK TJ =+25 o C A Unit 1. Load and line regulation are specified at constant junction temperature. Changes in O due to heating effects must be taken 10
11 Electrical Characteristics (MC7805A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 10, C I=0.33µF, C O=0.1µF, unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit Output oltage Line Regulation (Note1) O Regline TJ =+25 o C IO = 5mA to 1A, PO 15W I = 7.5 to 20 I = 7.5 to 25 IO = 500mA I = 8 to TJ =+25 o C I= 7.3 to I= 8 to Load Regulation (Note1) TJ =+25 o C IO = 5mA to 1.5A Regload IO = 5mA to 1A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma IO = 5mA to 1A Quiescent Current Change IQ I = 8 to 25, IO = 500mA ma I = 7.5 to 20, TJ =+25 o C Output oltage Drift / T Io = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz TA =+25 o C µ/o f = 120Hz, IO = 500mA I = 8 to db Dropout oltage Drop IO = 1A, TJ =+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 o C ma Peak Current IPK TJ= +25 o C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 11
12 Electrical Characteristics (MC7806A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I =11, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 o C IO = 5mA to 1A, PO 15W I = 8.6 to 21 I= 8.6 to 25 IO = 500mA I= 9 to TJ =+25 o C I= 8.3 to I= 9 to Load Regulation (Note1) TJ =+25 o C IO = 5mA to 1.5A Regload IO = 5mA to 1A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma IO = 5mA to 1A Quiescent Current Change IQ I = 9 to 25, IO = 500mA ma I= 8.5 to 21, TJ =+25 o C Output oltage Drift / T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz TA =+25 o C µ/o f = 120Hz, IO = 500mA I = 9 to db Dropout oltage Drop IO = 1A, TJ =+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 o C ma Peak Current IPK TJ=+25 o C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 12
13 Electrical Characteristics (MC7808A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 14, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 o C IO = 5mA to 1A, PO 15W I = 10.6 to 23 I= 10.6 to 25 IO = 500mA I= 11 to TJ =+25 o C I= 10.4 to I= 11 to Load Regulation (Note1) TJ =+25 o C IO = 5mA to 1.5A Regload IO = 5mA to 1A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 o C ma IO = 5mA to 1A Quiescent Current Change IQ I = 11 to 25, IO = 500mA ma I= 10.6 to 23, TJ =+25 o C Output oltage Drift / T IO = 5mA / o C Output Noise oltage N f = 10Hz to 100KHz TA =+25 o C µ/o f = 120Hz, IO = 500mA I = 11.5 to db Dropout oltage Drop IO = 1A, TJ =+25 o C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 o C ma Peak Current IPK TJ=+25 o C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 13
14 Electrical Characteristics (MC7809A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 15, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I = 11.2 to 24 I= 11.7 to 25 IO = 500mA I= 12.5 to TJ =+25 C I= 11.5 to I= 12.5 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.0A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 11.7 to 25, TJ=+25 C Quiescent Current Change IQ I = 12 to 25, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz TA =+25 C µ/o f = 120Hz, IO = 500mA I = 12 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant, junction temperature. Change in O due to heating effects must be taken 14
15 Electrical Characteristics (MC7810A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 16, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I =12.8 to 25 I= 12.8 to 26 IO = 500mA I= 13 to TJ =+25 C I= 12.5 to I= 13 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.5A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 13 to 26, TJ=+25 C Quiescent Current Change IQ I = 12.8 to 25, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz µ/o TA = C f = 120Hz, IO = 500mA I = 14 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 15
16 Electrical Characteristics (MC7812A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 19, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I = 14.8 to 27 I= 14.8 to 30 IO = 500mA I= 16 to TJ =+25 C I= 14.5 to I= 16 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.5A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 15 to 30, TJ=+25 C Quiescent Current Change IQ I = 14 to 27, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz TA =+25 C µ/o f = 120Hz, IO = 500mA I = 14 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 16
17 Electrical Characteristics (MC7815A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I =23, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I = 17.7 to 30 I= 17.9 to 30 IO = 500mA I= 20 to TJ =+25 C I= 17.5 to I= 20 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.5A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 17.5 to 30, TJ =+25 C Quiescent Current Change IQ I = 17.5 to 30, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz TA =+25 C µ/o f = 120Hz, IO = 500mA I = 18.5 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 17
18 Electrical Characteristics (MC7818A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 27, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I = 21 to 33 I= 21 to 33 IO = 500mA I= 21 to TJ =+25 C I= 20.6 to I= 24 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.5A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 21 to 33, TJ=+25 C Quiescent Current Change IQ I = 21 to 33, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz µ/o TA = C f = 120Hz, IO = 500mA I = 22 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 18
19 Electrical Characteristics (MC7824A) (Refer to the test circuits. 0 C < TJ < 125 C, Io =1A, I = 33, C I=0.33µF, C O=0.1µF, unless otherwise specified) Output oltage Parameter Symbol Conditions Min. Typ. Max. Unit Line Regulation (Note1) O Regline TJ =+25 C IO = 5mA to 1A, PO 15W I = 27.3 to 38 I= 27 to 38 IO = 500mA I= 21 to TJ =+25 C I= 26.7 to I= 30 to Load Regulation (Note1) TJ =+25 C IO = 5mA to 1.5A Regload IO = 5mA to 1.0A IO = 250mA to 750mA Quiescent Current IQ TJ =+25 C ma I = 27.3 to 38, TJ =+25 C Quiescent Current Change IQ I = 27.3 to 38, IO = 500mA ma IO = 5mA to 1.0A Output oltage Drift / T IO = 5mA / C Output Noise oltage N f = 10Hz to 100KHz TA = 25 C µ/o f = 120Hz, IO = 500mA I = 28 to db Dropout oltage Drop IO = 1A, TJ =+25 C Output Resistance ro f = 1KHz mω Short Circuit Current ISC I= 35, TA =+25 C ma Peak Current IPK TJ=+25 C A 1. Load and line regulation are specified at constant junction temperature. Change in O due to heating effects must be taken 19
20 Typical Perfomance Characteristics I Figure 1. Quiescent Current Figure 2. Peak Output Current Figure 3. Output oltage Figure 4. Quiescent Current 20
21 Typical Applications Input MC78XX/LM78XX Output Figure 5. DC Parameters Input MC78XX/LM78XX Output Figure 6. Load Regulation Input MC78XX/LM78XX Output Figure 7. Input MC78XX/LM78XX Output Figure 8. Fixed Output Regulator 21
22 Input MC78XX/LM78XX Output CI Co Figure 9. Constant Current Regulator Notes: (1) To specify an output voltage. substitute voltage value for "XX." A common ground is required between the input and the Output voltage. The input voltage must remain typically 2.0 above the output voltage even during the low point on the input ripple voltage. (2) CI is required if regulator is located an appreciable distance from power Supply filter. (3) CO improves stability and transient response. Input MC78XX/LM78XX Output CI Co I RI 5IQ O = XX(1+R2/R1)+IQR2 Figure 10. Circuit for Increasing Output oltage Input MC7805 LM7805 Output CI LM741 Co IRI 5 IQ O = XX(1+R2/R1)+IQR2 Figure 11. Adjustable Output Regulator (7 to 30) 22
23 Input MC78XX/LM78XX Output Figure 12. High Current oltage Regulator Input MC78XX/LM78XX Output Figure 13. High Output Current with Short Circuit Protection MC78XX/LM78XX LM741 Figure 14. Tracking oltage Regulator 23
24 MC7815 MC7915 Figure 15. Split Power Supply ( ±15-1A) Output Input MC78XX/LM78XX Figure 16. Negative Output oltage Circuit Input Output MC78XX/LM78XX Figure 17. Switching Regulator 24
25 Mechanical Dimensions Package TO ± ±0.20 (1.70) 1.30 ±0.10 (8.70) ø3.60 ± ± ± ±0.20 (1.46) (1.00) 1.27 ±0.10 (45 ) (3.00) (3.70) ± ± ± MAX. 2.54TYP [2.54 ±0.20] 0.80 ± TYP [2.54 ±0.20] ± ±
26 Mechancal Dimensions (Continued) Package 6.60 ±0.20 D-PAK 5.34 ±0.30 (0.50) (4.34) (0.50) 0.70 ± ± ± ± ±0.20 MAX TYP [2.30±0.20] 2.70 ± ± ± ± TYP [2.30±0.20] 6.10 ± ± ± ± ± ±0.20 (5.34) (5.04) (1.50) (2XR0.25) (0.70) MIN ± ± ±0.20 (0.10) (3.05) (0.90) (1.00) 0.76 ±
27 Ordering Information Product Number Output oltage Tolerance Package Operating Temperature LM7805CT ±4% TO ~ C Product Number Output oltage Tolerance Package Operating Temperature MC7805CT MC7806CT MC7808CT MC7809CT MC7810CT MC7812CT MC7815CT MC7818CT MC7824CT MC7805CDT MC7806CDT MC7808CDT MC7809CDT MC7810CDT MC7812CDT MC7805ACT MC7806ACT MC7808ACT MC7809ACT MC7810ACT MC7812ACT MC7815ACT MC7818ACT ±4% ±2% TO-220 D-PAK TO ~ C MC7824ACT 27
28 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 7/2/01 0.0m 001 Stock#DSxxxxxxxx 2001 Fairchild Semiconductor Corporation
MC78XX/LM78XX. 3-terminal 1A positive voltage regulator. Features. Description. Internal Block Digram. www.fairchildsemi.com
www.fairchildsemi.com 3-terminal 1A positive voltage regulator Features Current up to 1A Voltages of 5, 6, 8, 9, 10, 11, 12, 15, 18, 24V Thermal Overload Protection Short Circuit Protection Transistor
More informationKA79XX/KA79XXA. 3-Terminal 1A Negative Voltage Regulator. Features. Description. Internal Block Digram. www.fairchildsemi.com
3-Terminal 1A Negative oltage Regulator www.fairchildsemi.com Features Output Current in Excess of 1A s of -5, -6, -8, -9, -12, -15, -18, -24 Internal Thermal Overload Protection Short Circuit Protection
More informationLM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
More informationL7800 SERIES POSITIVE VOLTAGE REGULATORS
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5 A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
More informationLM78XX / LM78XXA 3-Terminal 1 A Positive Voltage Regulator
LM78XX / LM78XXA 3-Terminal A Positive oltage Regulator Features Output Current up to A s: 5, 6, 8, 9, 0,, 5, 8, 4 Thermal Overload Protection Short-Circuit Protection Output Transistor Safe Operating
More informationL78M00 SERIES POSITIVE VOLTAGE REGULATORS. www.tvsat.com.pl
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 0.5A OUTPUT VOLTAGES OF 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSISTOR SOA PROTECTION DESCRIPTION
More informationLM741. Single Operational Amplifier. Features. Description. Internal Block Diagram. www.fairchildsemi.com
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationLM79XX Series 3-Terminal Negative Regulators
LM79XX Series 3-Terminal Negative Regulators General Description The LM79XX series of 3-terminal regulators is available with fixed output voltages of b5v b8v b12v and b15v These devices need only one
More informationCS8481. 3.3 V/250 ma, 5.0 V/100 ma Micropower Low Dropout Regulator with ENABLE
3.3 /250 ma, 5.0 /100 ma Micropower Low Dropout Regulator with The CS8481 is a precision, dual Micropower linear voltage regulator. The switched 3.3 primary output ( OUT1 ) supplies up to 250 ma while
More informationL78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
More informationDescription. Table 1. Device summary
2 A positive voltage regulator IC Description Datasheet - production data Features TO-220 Output current up to 2 A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24 V Thermal protection Short circuit protection
More informationL4940 series VERY LOW DROP 1.5 A REGULATORS
L4940 series VERY LOW DROP 1.5 A REGULATORS PRECISE 5 V, 8.5 V, 10 V, 12 V OUTPUTS LOW DROPOUT VOLTAGE (500 typ at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
More informationLF00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT
LF00AB/C SERIES ERY LOW DROP OLTAGE REGULATORS WITH INHIBIT ERY LOW DROPOUT OLTAGE (5) ERY LOW QUIESCENT CURRENT (TYP. 50 µa IN OFF MODE, 500µA INON MODE) OUTPUT CURRENT UP TO 500 ma LOGIC-CONTROLLED ELECTRONIC
More informationBDX33/A/B/C. Symbol Parameter Value Units V CBO Collector-Base Voltage : BDX33 : BDX33A : BDX33B : BDX33C
Power Linear and Switching Applications High Gain General Purpose Power Darlington TR Complement to BDX34/34A/34B/34C respectively 1 TO-220 1.Base 2.Collector 3.Emitter NPN Epitaxial Silicon Transistor
More informationL78. Positive voltage regulator ICs. Description. Features
Positive voltage regulator ICs Description Datasheet - production data TO-220 Features DPAK TO-220FP D²PAK Output current up to 1.5 A Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V Thermal overload
More informationLM1084 5A Low Dropout Positive Regulators
5A Low Dropout Positive Regulators General Description The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5 at 5A of load current. It has the same pin-out as
More informationEquivalent Circuit. Operating Characteristics at Ta = 25 C, V CC = ±34V, R L = 8Ω, VG = 40dB, Rg = 600Ω, R L : non-inductive load STK4181V
Ordering number: 2137B Thick Film Hybrid IC STK4181V AF Power Amplifier (Split Power Supply) (45W + 45W min, THD = 0.08%) Features Pin-compatible with the STK4102II series. The STK4101V series use the
More informationKA7500C. SMPS Controller. Features. Description. Internal Block Diagram. www.fairchildsemi.com
SMPS Controller www.fairchildsemi.com Features Internal Regulator Provides a Stable 5V Reference Supply Trimmed to ±1% Accuracy. Uncommitted Output TR for 200mA Sink or Source Current Output Control for
More informationUC3842/UC3843/UC3844/UC3845
SMPS Controller www.fairchildsemi.com Features Low Start up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency up to 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequencycurrent-mode
More informationAdvanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
More informationLM2941/LM2941C 1A Low Dropout Adjustable Regulator
LM2941/LM2941C 1A Low Dropout Adjustable Regulator General Description The LM2941 positive voltage regulator features the ability to source 1A of output current with a typical dropout voltage of 0.5V and
More informationBD434/436/438. Symbol Parameter Value Units V CBO Collector-Base Voltage : BD434 : BD436 : BD438
Medium Power Linear and Switching Applications Complement to BD433, BD435 and BD437 respectively 1 TO26 1. Emitter 2.Collector 3.Base PNP Epitaxial Silicon Transistor Absolute Maximum Ratings T C =25 C
More informationAS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
More informationL78L. Positive voltage regulators. Description. Features
Positive voltage regulators Datasheet - production data Features Output current up to 100 ma Output voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 V thermal overload protection Short-circuit protection
More informationSTLQ015. 150 ma, ultra low quiescent current linear voltage regulator. Description. Features. Application
150 ma, ultra low quiescent current linear voltage regulator Description Datasheet - production data Features SOT23-5L Input voltage from 1.5 to 5.5 V Very low quiescent current: 1.0 µa (typ.) at no load
More informationLM337. Three-terminal adjustable negative voltage regulators. Features. Description
Three-terminal adjustable negative voltage regulators Datasheet - production data current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional
More informationPQ05RD11 Series/PQ3RD13
Low Power-Loss oltage Regulators PQ5RD Series/PQRD PQ5RD Series/PQRD A Output, General Purpose Low Power-loss oltage Regulators Features Low power-loss(dropout voltage : MAX..5 at Io=.5A) Line-up for.,
More informationLM217M, LM317M. Medium current 1.2 to 37 V adjustable voltage regulator. Description. Features
Medium current 1.2 to 37 V adjustable voltage regulator Datasheet - production data Description The LM217M and LM317M are monolithic integrated circuits in DPAK package used as positive adjustable voltage
More informationFAN8082 (KA3082N) Bi-directional DC Motor Driver. Features. Description. Typical Applications. Ordering Information. www.fairchildsemi.
Bi-directional DC Motor Driver www.fairchildsemi.com Features Built-in brake function for stable brake characteristics. Built-in element to absorb a surge current derived from changing motor direction
More informationLM138 LM338 5-Amp Adjustable Regulators
LM138 LM338 5-Amp Adjustable Regulators General Description The LM138 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5A over a 1 2V to 32V output range
More informationLM3940 1A Low Dropout Regulator for 5V to 3.3V Conversion
1A Low Dropout Regulator for 5V to 3.3V Conversion General Description The LM3940 is a 1A low dropout regulator designed to provide 3.3V from a 5V supply. The LM3940 is ideally suited for systems which
More informationSURFACE MOUNT LED LAMP STANDARD BRIGHT 0606
PACKAGE DIMENSIONS 0.075 (1.9) 0.063 (1.6) 0.035 (0.9) TOP 0.047 (1.2) 0.012 (0.3) 0.032 [0.8] SIDE 0.043 [1.1] 1 3 0.020 [0.5] 2 4 BOTTOM CATHODE MASK 1 2 3 4 HER / AlGaAs Red / Yellow (for-34) Green
More informationunit : mm With heat sink (see Pd Ta characteristics)
Ordering number: EN1321E Monolithic Linear IC LA4261 3.5 W 2-Channel AF Power Amplifier for Home Stereos and Music Centers Features. Minimum number of external parts required (No input capacitor, bootstrap
More informationAP1509. 150KHz, 2A PWM BUCK DC/DC CONVERTER. Description. Pin Assignments V IN. Applications. Features. (Top View) GND GND. Output AP1509 GND GND
Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 2A load without additional transistor. It saves board space. The external
More informationLM117 LM317A LM317 3-Terminal Adjustable Regulator
LM117 LM317A LM317 3-Terminal Adjustable Regulator General Description The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1 5A over a 1 2V to 37V
More informationLM2576R. 3.0A, 52kHz, Step-Down Switching Regulator FEATURES. Applications DESCRIPTION TO-220 PKG TO-220V PKG TO-263 PKG ORDERING INFORMATION
LM2576 FEATURES 3.3, 5.0, 12, 15, and Adjustable Output ersions Adjustable ersion Output oltage Range, 1.23 to 37 +/- 4% AG10Maximum Over Line and Load Conditions Guaranteed 3.0A Output Current Wide Input
More informationCD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset
October 1987 Revised March 2002 CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset General Description The CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits
More informationLM350. 3.0 A, Adjustable Output, Positive Voltage Regulator THREE TERMINAL ADJUSTABLE POSITIVE VOLTAGE REGULATOR
3. A, able Output, Positive Voltage Regulator The is an adjustable threeterminal positive voltage regulator capable of supplying in excess of 3. A over an output voltage range of 1.2 V to 33 V. This voltage
More informationLM380 Audio Power Amplifier
LM380 Audio Power Amplifier General Description The LM380 is a power audio amplifier for consumer application. In order to hold system cost to a minimum, gain is internally fixed at 34 db. A unique input
More informationADJUSTABLE VOLTAGE AND CURRENT REGULATOR
L200 ADJUSTABLE VOLTAGE AND CURRENT REGULATOR ADJUSTABLE OUTPUT CURRENT UP TO 2 A (GUARANTEED UP TO Tj = 150 C) ADJUSTABLE OUTPUT VOLTAGE DOWN TO 2.85 V INPUT OVERVOLTAGE PROTECTION (UP TO 60 V, 10 ms)
More informationCD40174BC CD40175BC Hex D-Type Flip-Flop Quad D-Type Flip-Flop
Hex D-Type Flip-Flop Quad D-Type Flip-Flop General Description The CD40174BC consists of six positive-edge triggered D- type flip-flops; the true outputs from each flip-flop are externally available. The
More informationLM1117/LM1117I 800mA Low-Dropout Linear Regulator
LM1117/LM1117I 800mA Low-Dropout Linear Regulator General Description The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2 at 800mA of load current. It has the same pin-out as
More informationPAM2804. Pin Assignments. Description. Applications. Features. Typical Applications Circuit 1A STEP-DOWN CONSTANT CURRENT, HIGH EFFICIENCY LED DRIVER
1A STEP-DOWN CONSTANT CURRENT, HIGH EFFICIENCY LED DRIER Description Pin Assignments The is a step-down constant current LED driver. When the input voltage is down to lower than LED forward voltage, then
More informationLOW POWER NARROWBAND FM IF
Order this document by MC336B/D The MC336B includes an Oscillator, Mixer, Limiting Amplifier, Quadrature Discriminator, Active Filter, Squelch, Scan Control and Mute Switch. This device is designed for
More informationDescription SO-8. series. Furthermore, in the 8-pin configuration Very low-dropout voltage (0.2 V typ.)
ery low-dropout voltage regulator with inhibit function TO-92 Bag TO-92 Tape and reel Ammopack 1 2 3 SO-8 Description Datasheet - production data The is a very low-dropout voltage regulator available in
More informationULN2803A ULN2804A OCTAL PERIPHERAL DRIVER ARRAYS
Order this document by ULN283/D The eight NPN Darlington connected transistors in this family of arrays are ideally suited for interfacing between low logic level digital circuitry (such as TTL, CMOS or
More informationLM555/NE555/SA555. Single Timer. Description. Features. Applications. Internal Block Diagram. Vcc GND. Trigger. Discharge. Output F/F.
Single Timer www.fairchildsemi.com Features High Current Drive Capability (00mA) Adjustable Duty Cycle Temperature Stability of 0.005%/ C Timing From µsec to Hours Turn off Time Less Than µsec Applications
More information5A LOW DROPOUT LINEAR REGULATOR General Description. Features. Applications
General Description The is a series of low dropout positive voltage regulators with a maximum dropout of.5v at 5A of load current. The series features on-chip thermal limiting which provides protection
More informationunit:mm 3049A-SIP12H 8.4 7.0
Ordering number:enn1277e Monolithic Linear IC LA4445 5.5W 2-Channel AF Power Amplifier Features Dual channels. Output : 5.5W 2 (typ.) Minimun number of external parts required. Small pop noise at the time
More informationLM2941 LM2941C 1A Low Dropout Adjustable Regulator
June 1994 LM2941 LM2941C 1A Low Dropout Adjustable Regulator General Description The LM2941 positive voltage regulator features the ability to source 1A of output current with a typical dropout voltage
More informationKIA7805AF/API~KIA7824AF/API SEMICONDUCTOR TECHNICAL DATA THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 7V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, 24V.
SEMICONDUCTOR TECHNICAL DATA KIA785AF/API~KIA7824AF/API BIPOLAR LINEAR INTEGRATED THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 7V, 8V, 9V, 1V, 12V, 15V, 18V, 2V, 24V. FEATURES Internal Thermal Overload
More information1.5A L.D.O. VOLTAGE REGULATOR (Adjustable & Fixed) LM1086
FEATURES Output Current of 1.5A Fast Transient Response 0.04% Line Regulation 0.2% Load Regulation Internal Thermal and Current Limiting Adjustable or Fixed Output oltage(1.5, 1.8, 2.5, 3.3, 5.0) Surface
More information1.5A Very L.D.O Voltage Regulator LM29150/29151/29152
FEATURES High Current Capability 1.5A Low Dropout Voltage 350mV Low Ground Current Accurate 1% Guaranteed Initial Tolerance Extremely Fast Transient Response Reverse-Battery and "Load Dump" Protection
More informationL293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
More informationMM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines
More informationMC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT
Order this document by MC3464/D The MC3464 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessor-based systems. It offers the designer an economical solution
More informationNTE923 & NTE923D Integrated Circuit Precision Voltage Regulator
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator Description: The NTE923 and NTE923D are voltage regulators designed primarily for series regulator applications. By themselves, these devices
More informationMM74C74 Dual D-Type Flip-Flop
Dual D-Type Flip-Flop General Description The MM74C74 dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit cotructed with N- and P-channel enhancement traistors. Each flip-flop
More information0.9V Boost Driver PR4403 for White LEDs in Solar Lamps
0.9 Boost Driver for White LEDs in Solar Lamps The is a single cell step-up converter for white LEDs operating from a single rechargeable cell of 1.2 supply voltage down to less than 0.9. An adjustable
More informationHigh Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338 FEATURES High accuracy over line and load: ±.8% @ 25 C, ±1.4% over temperature Ultralow dropout voltage: 19 mv (typ) @ 1 A Requires
More informationDescription SO-8. Table 1. Device summary. Order codes. SO-8 (tape and reel) TO-92 (Bag) TO-92 (Ammopack) TO-92 (tape and reel)
Low current 1.2 to 37 V adjustable voltage regulators Description Datasheet - production data TO-92 SO-8 TO-92 Tape and reel Bag Ammopack Features Outuput voltage range: 1.2 to 37 V Output current up to
More informationDescription. Table 1. Device summary. Order codes. TO-220 (single gauge) TO-220 (double gauge) D²PAK (tape and reel) TO-220FP
1.2 V to 37 V adjustable voltage regulators Description Datasheet - production data TO-220 TO-220FP The LM217, LM317 are monolithic integrated circuits in TO-220, TO-220FP and D²PAK packages intended for
More information2N7000 / 2N7002 / NDS7002A N-Channel Enhancement Mode Field Effect Transistor
November 995 N7 / N7 / NS7A N-Channel Enhancement Mode Field Effect Transistor General escription Features These N-Channel enhancement mode field effect transistors are produced using Fairchild's proprietary,
More informationObsolete Product(s) - Obsolete Product(s)
32 W hi-fi audio power amplifier Features High output power (50 W music power IEC 268.3 rules) High operating supply voltage (50 V) Single or split supply operations Very low distortion Short-circuit protection
More information1A L.D.O VOLTAGE REGULATOR
FEATURES Output Current up to 1 A Low Dropout Voltage (1.2V at 1A Output current) Three Terminal Adjustable(ADJ) or Fixed 1.2V, 1.5V, 1.8V, 2.5V, 2.85V, 5.0V Line Regulation typically at 0.1% max. Load
More informationSymbol Parameter Value Unit V i-o Input-output Differential Voltage 40 V I O Output Current Intenrally Limited Top
LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE : 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 1.5A 0.1% LINE AND LOAD REGULATION FLOATING OPERATION FOR HIGH VOLTAGES COMPLETE SERIES OF PROTECTIONS
More informationMIC2940A/2941A. Features. General Description. Applications. Pin Configuration. 1.2A Low-Dropout Voltage Regulator
MIC294A/2941A 1.2A Low-Dropout oltage Regulator General Description The MIC294A and MIC2941A are bulletproof efficient voltage regulators with very low dropout voltage (typically 4 at light loads and 35
More informationAP1506. 150KHz, 3A PWM BUCK DC/DC CONVERTER. Pin Assignments. Description. Features. Applications. ( Top View ) 5 SD 4 FB 3 Gnd 2 Output 1 V IN
Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 3A load without external transistor. Due to reducing the number of external
More information1.0A LOW DROPOUT LINEAR REGULATOR
1.0A LOW DROPOUT LINEAR REGULATOR Description Pin Assignments The is a low dropout three-terminal regulator with 1.0A output current ability, and the dropout voltage is specified at typical 1.1V at 1.0A
More informationLOW DROPOUT VOLTAGE REGULATOR
LOW DROPOUT VOLTAGE REGULATOR GENERAL DESCRIPTION The NJM884/A is a low dropout voltage regulator with ON/OFF control. Advanced Bipolar technology achieves low noise, high ripple rejection and low quiescent
More informationFeatures. Applications
Pb Lead-Free 1A LOW DROPOUT LINEAR REGULATOR Description The is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The series provides current limiting and
More informationMM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines
More informationTDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description
10 + 10 W stereo amplifier for car radio Features Low distortion Low noise Protection against: Output AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground
More informationLDS8720. 184 WLED Matrix Driver with Boost Converter FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
184 WLED Matrix Driver with Boost Converter FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier) 250 mv
More informationFeatures. T A=25 o C unless otherwise noted. Symbol Parameter Ratings Units. (Note 1b) 0.46
N-Channel.8 Vgs Specified PowerTrench MOSFET October 2 General Description This 2V N-Channel MOSFET uses Fairchild s high voltage PowerTrench process. It has been optimized for power management applications.
More informationCD4013BC Dual D-Type Flip-Flop
Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit cotructed with N- and P-channel enhancement mode traistors. Each
More informationLM741 Operational Amplifier
Operational Amplifier General Description The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in
More information74AC139 74ACT139 Dual 1-of-4 Decoder/Demultiplexer
Dual 1-of-4 Decoder/Demultiplexer General Description The AC/ACT139 is a high-speed, dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each accepting two inputs and providing
More informationTDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
More informationCD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate
CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated
More informationHigh Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator ADP3339
Data Sheet High Accuracy, Ultralow IQ,.5 A, anycap Low Dropout Regulator FEATURES FUNCTIONAL BLOCK DIAGRAM High accuracy over line and load: ±.9% at 5 C, ±.5% over temperature Ultralow dropout voltage:
More informationLA4725. Specifications. Monolithic Linear IC 2-channel 30W BTL Audio Amplifier. Maximum Ratings at Ta = 25 C. http://onsemi.com
Ordering number : EN1A LA4 Monolithic Linear IC -channel W BTL Audio Amplifier http://onsemi.com Overview The LA4 is a -channel BTL audio power amplifier IC for Car audio. It was designed for the best
More informationLM380 Audio Power Amplifier
LM380 Audio Power Amplifier General Description The LM380 is a power audio amplifier for consumer application In order to hold system cost to a minimum gain is internally fixed at 34 db A unique input
More informationOp Amp Circuit Collection
Op Amp Circuit Collection Note: National Semiconductor recommends replacing 2N2920 and 2N3728 matched pairs with LM394 in all application circuits. Section 1 Basic Circuits Inverting Amplifier Difference
More informationMM74HC4538 Dual Retriggerable Monostable Multivibrator
MM74HC4538 Dual Retriggerable Monostable Multivibrator General Description The MM74HC4538 high speed monostable multivibrator (one shots) is implemented in advanced silicon-gate CMOS technology. They feature
More informationHIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
DESCRIPTION The, /6 single-channel and /6 dual-channel optocouplers consist of a 5 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable output. This
More informationTDA2003 10W CAR RADIO AUDIO AMPLIFIER
TDA2003 10W CAR RADIO AUDIO AMPLIFIER DESCRIPTION The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external
More informationTL783C, TL783Y HIGH-VOLTAGE ADJUSTABLE REGULATOR
HIGH-VOLTAGE USTABLE REGULATOR SLVS36C SEPTEMBER 1981 REVISED APRIL 1997 Output Adjustable From 1.25 V to 125 V When Used With an External Resistor Divider 7-mA Output Current Full Short-Circuit, Safe-Operating-Area,
More informationCD4013BC Dual D-Type Flip-Flop
CD4013BC Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.
More informationP D 215 1.25 Operating Junction Temperature T J 200 C Storage Temperature Range T stg 65 to +150 C
SEMICONDUCTOR TECHNICAL DATA Order this document by /D The RF Line The is designed for output stages in band IV and V TV transmitter amplifiers. It incorporates high value emitter ballast resistors, gold
More informationUNISONIC TECHNOLOGIES CO.,LTD
TDA UNISONIC TECHNOLOGIES CO.,LTD +W STEREO AMPLIFIER FOR CAR RADIO DESCRIPTION The UTC TDA is a class B dual audio power amplifier and is designed for car radio applications. HZIP-11 FEATURES * Low distortion.
More informationwww.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LF411 Low Offset, Low Drift JFET Input Operational Amplifier General Description
More informationCA723, CA723C. Voltage Regulators Adjustable from 2V to 37V at Output Currents Up to 150mA without External Pass Transistors. Features.
CA73, CA73C Data Sheet April 1999 File Number 788. Voltage Regulators Adjustable from V to 37V at Output Currents Up to 1mA without External Pass Transistors The CA73 and CA73C are silicon monolithic integrated
More informationBC546B, BC547A, B, C, BC548B, C. Amplifier Transistors. NPN Silicon. Pb Free Package is Available* Features. http://onsemi.com MAXIMUM RATINGS
B, A, B, C, B, C Amplifier Transistors NPN Silicon Features PbFree Package is Available* COLLECTOR 1 2 BASE MAXIMUM RATINGS Collector-Emitter oltage Collector-Base oltage Rating Symbol alue Unit CEO 65
More informationUnderstanding the Terms and Definitions of LDO Voltage Regulators
Application Report SLVA79 - October 1999 Understanding the Terms and Definitions of ltage Regulators Bang S. Lee Mixed Signal Products ABSTRACT This report provides an understanding of the terms and definitions
More informationDM74LS00 Quad 2-Input NAND Gate
DM74LS00 Quad 2-Input NAND Gate General Description This device contains four independent gates each of which performs the logic NAND function. Ordering Code: August 1986 Revised March 2000 Order Number
More informationL4970A 10A SWITCHING REGULATOR
10A SWITCHING REGULATOR 10A OUTPUT CURRENT 5.1 TO 40 OUTPUT OLTAGE RANGE 0 TO 90% DUTY CYCLE RANGE INTERNAL FEED-FORWARD LINE REGULA- TION INTERNAL CURRENT LIMITING PRECISE 5.1 ± 2% ON CHIP REFERENCE RESET
More informationDM74121 One-Shot with Clear and Complementary Outputs
June 1989 Revised July 2001 DM74121 One-Shot with Clear and Complementary Outputs General Description The DM74121 is a monostable multivibrator featuring both positive and negative edge triggering with
More informationDM74LS05 Hex Inverters with Open-Collector Outputs
Hex Inverters with Open-Collector Outputs General Description This device contains six independent gates each of which performs the logic INVERT function. The open-collector outputs require external pull-up
More informationunit:mm 3006B-DIP16 0.71 2.54 0.48
Ordering number:enn505g Monolithic Linear IC LA3361 PLL FM Multiplex Stereo Demodulator Overview The LA3361, PLL FM multiplex stereo demodulator, is designed for low supply voltage-use appliance such as
More information