LF00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT
|
|
|
- Godwin Booker
- 8 years ago
- Views:
Transcription
1 LF00AB/C SERIES ERY LOW DROP OLTAGE REGULATORS WITH INHIBIT ERY LOW DROPOUT OLTAGE (5) ERY LOW QUIESCENT CURRENT (TYP. 50 µa IN OFF MODE, 500µA INON MODE) OUTPUT CURRENT UP TO 500 ma LOGIC-CONTROLLED ELECTRONIC SHUTDOWN OUTPUT OLTAGES OF 1.25; 1.5; 1.8; 2.5; 2.7; 3; 3.3; 3.5; 4; 4.5; 4.7; 5; 5.2; 5.5; 6; 8; 8.5; 9; 12 INTERNAL CURRENT AND THERMAL LIMIT ONLY 2.2µF FOR STABILITY AAILABLEIN ± 1% (AB) OR ± 2% (C) SELECTIONAT 25 o C SUPPLY OLTAGE REJECTION: 80 (TYP.) TEMPERATURE RANGE: -40 TO 125 o C TO-220 PENTAWATT TO-220FP DESCRIPTION The LF00 series are very Low Drop regulators available in PENTAWATT, TO-220, TO-220FP, DPAK and PPAK package and in a wide range of output voltages. The very Low Drop voltage (5) and the very low quiescent current make them particularly suitable for Low Noise, Low Power applications and specially in battery powered systems. In the 5 pins configuration (PENTAWATT and PPAK) a Shutdown Logic Control function is SCHEMATIC DIAGRAM PPAK DPAK available (pin 2, TTL compatible). This means that when the device is used as a local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. In the three terminal configuration the device has the same electrical performance, but is fixed in the ON state. It requires only a 2.2 µf capacitor for stability allowing space and cost saving. November /32
2 ABSOLUTE MAXIMUM RATINGS Symbol Parameter alue Unit i DC Input oltage -0.5 to 40 (*) I o Output Current Internally limited P tot Power Dissipation Internally limited T stg Storage Temperature Range - 40 to 150 T op Operating Junction Temperature Range - 40 to 125 (*) For 18 < IN < 40 the regulator is in shut-down o C o C THERMAL DATA Symbol Parameter PENTAWATT TO-220 TO-220FP DPAK/PPAK Unit R thj-case R thj-amb Thermal Resistance Junction-case Thermal Resistance Junction-ambient o C/W o C/W CONNECTION DIAGRAM (top view) PENTAWATT TO-220 TO-220FP PPAK DPAK 2/32
3 ORDERING NUMBERS Type PENTAWATT TO-220 TO-220FP DPAK PPAK Output oltage LF12C (*) LF12AB (*) LF15C (*) LF15AB (*) LF18C LF18AB LF25C LF25AB LF27C LF27AB LF30C LF30AB LF33C LF33AB LF35C LF35AB LF40C LF40AB LF45C (*) LF45AB (*) LF47C LF47AB LF50C LF50AB LF52C LF52AB LF55C LF55AB LFC LFAB LF80C LF80AB LF85C LF85AB LF90C LF90AB LF120C LF120AB LF12C5 LF12AB5 LF15C5 LF15AB5 LF18C5 LF18AB5 LF25C5 LF25AB5 LF27C5 LF27AB5 LF30C5 LF30AB5 LF33C5 LF33AB5 LF35C5 LF35AB5 LF40C5 LF40AB5 LF45C5 LF45AB5 LF47C5 LF47AB5 LF50C5 LF50AB5 LF52C5 LF52AB5 LF55C5 LF55AB5 LFC5 LFAB5 LF80C5 LF80AB5 LF85C5 LF85AB5 LF90C5 LF90AB5 LF120C5 LF120AB5 LF12C LF12AB LF15C LF15AB LF18C LF18AB LF25C LF25AB LF27C LF27AB LF30C LF30AB LF33C LF33AB LF35C LF35AB LF40C LF40AB LF45C LF45AB LF47C LF47AB LF50C LF50AB LF52C LF52AB LF55C LF55AB LFC LFAB LF80C LF80AB LF85C LF85AB LF90C LF90AB LF120C LF120AB LF12CP LF12ABP LF15CP LF15ABP LF18CP LF18ABP LF25CP LF25ABP LF27CP LF27ABP LF30CP LF30ABP LF33CP LF33ABP LF35CP LF35ABP LF40CP LF40ABP LF45CP LF45ABP LF47CP LF47ABP LF50CP LF50ABP LF52CP LF52ABP LF55CP LF55ABP LFCP LFABP LF80CP LF80ABP LF85CP LF85ABP LF90CP LF90ABP LF120CP LF120ABP LF12CDT LF12ABDT LF15CDT LF15ABDT LF18CDT LF18ABDT LF25CDT LF25ABDT LF27CDT LF27ABDT LF30CDT LF30ABDT LF33CDT LF33ABDT LF35CDT LF35ABDT LF40CDT LF40ABDT LF45CDT LF45ABDT LF47CDT LF47ABDT LF50CDT LF50ABDT LF52CDT LF52ABDT LF55CDT LF55ABDT LFCDT LFABDT LF80CDT LF80ABDT LF85CDT LF85ABDT LF90CDT LF90ABDT LF120CDT LF120ABDT LF12CPT LF12ABPT LF15CPT LF15ABPT LF18CPT LF18ABPT LF25CPT LF25ABPT LF27CPT LF27ABPT LF30CPT LF30ABPT LF33CPT LF33ABPT LF35CPT LF35ABPT LF40CPT LF40ABPT LF45CPT LF45ABPT LF47CPT LF47ABPT LF50CPT LF50ABPT LF52CPT LF52ABPT LF55CPT LF55ABPT LFCPT LFABPT LF80CPT LF80ABPT LF85CPT LF85ABPT LF90CPT LF90ABPT LF120CPT LF120ABPT TEST CIRCUITS 3/32
4 ELECTRICAL CHARACTERISTICS FOR LF12AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 3.3 I o =50mA, i = <T a <85 o C i Operating Input oltage o Line Regulation i = 2.5 to 16, I o = 5 ma 2 10 m o Load Regulation i =2.8 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 Io =0mA i = 2.6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma 1.25 il Control Input Logic Low -40 < Ta <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa ELECTRICAL CHARACTERISTICS FOR LF12C (refer to the test circuits, Tj =25 o C, Ci = 0.1 µf, Co = 2.2 µf unless otherwise specified) o Output oltage I o =50mA, i = 3.3 I o =50mA, i = <T a <85 o C i Operating Input oltage o Line Regulation i = 2.5 to 16, I o = 5 ma 2 10 m o Load Regulation i = 2.8 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 I o =0mA i = 2.6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma 1.25 il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < Ta <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
5 ELECTRICAL CHARACTERISTICS FOR LF15AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 3.5 I o =50mA, i = <T a <85 o C i Operating Input oltage o Line Regulation i = 2.5 to 16, I o = 5 ma 2 10 m o Load Regulation i = 2.8 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 Io =0mA i = 2.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma 1 il Control Input Logic Low -40 < Ta <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa ELECTRICAL CHARACTERISTICS FOR LF15C (refer to the test circuits, Tj =25 o C, Ci = 0.1 µf, Co = 2.2 µf unless otherwise specified) o Output oltage I o =50mA, i = 3.5 I o =50mA, i = <T a <85 o C i Operating Input oltage o Line Regulation i = 2.5 to 16, I o = 5 ma 2 10 m o Load Regulation i = 2.8 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 I o =0mA i = 2.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma 1 il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < Ta <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
6 ELECTRICAL CHARACTERISTICS FOR LF18AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 3.3 I o =50mA, i = <T a <85 o C i Operating Input oltage 3 16 o Line Regulation i = 2.8 to 16, I o = 5 ma 2 12 m o Load Regulation i = 3.3 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 Io =0mA i = 3.1 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < Ta <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa ELECTRICAL CHARACTERISTICS FOR LF18C (refer to the test circuits, Tj =25 o C, Ci = 0.1 µf, Co = 2.2 µf unless otherwise specified) o Output oltage I o =50mA, i = 3.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 3 16 o Line Regulation i = 2.8 to 16, I o = 5 ma 2 12 m o Load Regulation i = 3.3 I o = 5 to 500 ma 2 10 m i = 2.5 to 16 I o =0mA i = 3.1 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 3.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < Ta <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
7 ELECTRICAL CHARACTERISTICS FOR LF25AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 4.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 3.5 to 16, I o = 5 ma 2 12 m o Load Regulation i = 3.8 I o = 5 to 500 ma 2 12 m i = 3.5 to 16 Io =0mA i = 3.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 4.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF25C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 4.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 3.5 to 16, I o = 5 ma 2 12 m o Load Regulation i = 3.8 I o = 5 to 500 ma 2 12 m i = 3.5 to 16 Io =0mA i = 3.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 4.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
8 ELECTRICAL CHARACTERISTICS FOR LF27AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 4.7 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 3.7 to 16, I o = 5 ma 2 13 m o Load Regulation i =4 I o = 5 to 500 ma 2 13 m i = 3.7 to 16 Io =0mA i = 4 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 4.7 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF27C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 4.7 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 3.7 to 16, I o = 5 ma 2 13 m o Load Regulation i =4 I o = 5 to 500 ma 2 13 m i = 3.7 to 16 Io =0mA i = 4 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 4.7 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
9 ELECTRICAL CHARACTERISTICS FOR LF30AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =5 I o =50mA, i = 5-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4 to 16, I o = 5 ma 3 15 m o Load Regulation i = 4.3 I o = 5 to 500 ma 3 15 m i = 4 to 16 Io =0mA i = 4.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =5±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF30C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =5 I o =50mA, i = 5-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4 to 16, I o = 5 ma 3 15 m o Load Regulation i = 4.3 I o = 5 to 500 ma 3 15 m i = 4 to 16 Io =0mA i = 4.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =5±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
10 ELECTRICAL CHARACTERISTICS FOR LF33AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 5.3 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4.3 to 16, I o = 5 ma 3 16 m o Load Regulation i = 4.6 I o = 5 to 500 ma 3 16 m i = 4.3 to 16 Io =0mA i = 4.6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 5.3 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF33C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 5.3 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4.3 to 16, I o = 5 ma 3 16 m o Load Regulation i = 4.6 I o = 5 to 500 ma 3 16 m i = 4.3 to 16 Io =0mA i = 4.6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 5.3 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
11 ELECTRICAL CHARACTERISTICS FOR LF35AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 5.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4.5 to 16, I o = 5 ma 3 17 m o Load Regulation i = 4.8 I o = 5 to 500 ma 3 17 m i = 4.5 to 16 Io =0mA i = 4.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 5.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF35C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 5.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 4.5 to 16, I o = 5 ma 3 17 m o Load Regulation i = 4.8 I o = 5 to 500 ma 3 17 m i = 4.5 to 16 Io =0mA i = 4.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 5.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
12 ELECTRICAL CHARACTERISTICS FOR LF40AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =6 I o =50mA, i = 6-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5 to 16, I o = 5 ma 4 20 m o Load Regulation i = 5.3 I o = 5 to 500 ma 4 20 m i = 5 to 16 Io =0mA i = 5.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =6±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF40C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =6 I o =50mA, i = 6-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5 to 16, I o = 5 ma 4 20 m o Load Regulation i = 5.3 I o = 5 to 500 ma 4 20 m i = 5 to 16 Io =0mA i = 5.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =6±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
13 ELECTRICAL CHARACTERISTICS FOR LF45AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 6.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5.5 to 16, I o = 5 ma 4 22 m o Load Regulation i = 5.8 I o = 5 to 500 ma 4 22 m i = 5.5 to 16 Io =0mA i = 5.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 6.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF45C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 6.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5.5 to 16, I o = 5 ma 4 22 m o Load Regulation i = 5.8 I o = 5 to 500 ma 4 22 m i = 5.5 to 16 Io =0mA i = 5.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 6.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa 13/32
14 ELECTRICAL CHARACTERISTICS FOR LF47AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 6.7 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5.7 to 16, I o = 5 ma 4 23 m o Load Regulation i =6 I o = 5 to 500 ma 4 23 m i = 5.7 to 16 Io =0mA i = 6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 6.7 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF47C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 6.7 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 5.7 to 16, I o = 5 ma 4 23 m o Load Regulation i =6 I o = 5 to 500 ma 4 23 m i = 5.7 to 16 Io =0mA i = 6 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 6.7 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
15 ELECTRICAL CHARACTERISTICS FOR LF50AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =7 I o =50mA, i = 7-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6 to 16, I o = 5 ma 5 25 m o Load Regulation i = 6.3 I o = 5 to 500 ma 5 25 m i = 6 to 16 Io =0mA i = 6.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =7±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF50C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =7 I o =50mA, i = 7-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6 to 16, I o = 5 ma 5 25 m o Load Regulation i = 6.3 I o = 5 to 500 ma 5 25 m i = 6 to 16 Io =0mA i = 6.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =7±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
16 ELECTRICAL CHARACTERISTICS FOR LF52AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 7.2 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6.2 to 16, I o = 5 ma 5 26 m o Load Regulation i = 6.5 I o = 5 to 500 ma 5 26 m i = 6.2 to 16 Io =0mA i = 6.5 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 7.2 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF52C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 7.2 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6.2 to 16, I o = 5 ma 5 26 m o Load Regulation i = 6.5 I o = 5 to 500 ma 5 26 m i = 6.2 to 16 Io =0mA i = 6.5 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 7.2 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa /32
17 ELECTRICAL CHARACTERISTICS FOR LF55AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 7.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6.5 to 16, I o = 5 ma 5 27 m o Load Regulation i = 6.8 I o = 5 to 500 ma 5 27 m i = 6.5 to 16 Io =0mA i = 6.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 7.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF55C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 7.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 6.5 to 16, I o = 5 ma 5 27 m o Load Regulation i = 6.8 I o = 5 to 500 ma 5 27 m i = 6.5 to 16 Io =0mA i = 6.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 7.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 6, c =6 10 µa 17/32
18 ELECTRICAL CHARACTERISTICS FOR LFAB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =8 I o =50mA, i = 8-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 7 to 16, I o = 5 ma 6 30 m o Load Regulation i = 7.3 I o = 5 to 500 ma 6 30 m i = 7 to 16 Io =0mA 1.5 ma i = 7.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =8±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LFC (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =8 I o =50mA, i = 8-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 7 to 16, I o = 5 ma 6 30 m o Load Regulation i = 7.3 I o = 5 to 500 ma 6 30 m i = 7 to 16 Io =0mA 1.5 ma i = 7.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =8±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa /32
19 ELECTRICAL CHARACTERISTICS FOR LF80AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =10 I o =50mA, i = 10-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 9 to 16, I o = 5 ma 8 40 m o Load Regulation i = 9.3 I o = 5 to 500 ma 8 40 m i = 9 to 16 Io =0mA 1.5 ma i = 9.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =10±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF80C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =10 I o =50mA, i = 10-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i = 9 to 16, I o = 5 ma 8 40 m o Load Regulation i = 9.3 I o = 5 to 500 ma 8 40 m i = 9 to 16 Io =0mA 1.5 ma i = 9.3 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =10±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa /32
20 ELECTRICAL CHARACTERISTICS FOR LF85AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 10.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 9.5 to 16, I o = 5 ma 8 42 m o Load Regulation i = 9.8 I o = 5 to 500 ma 8 42 m i = 9.5 to 16 Io =0mA 1.5 ma i = 9.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 10.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF85C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = 10.5 I o =50mA, i = <T a <85 o C i Operating Input oltage 16 o Line Regulation i = 9.5 to 16, I o = 5 ma 8 42 m o Load Regulation i = 9.8 I o = 5 to 500 ma 8 42 m i = 9.5 to 16 Io =0mA 1.5 ma i = 9.8 to 16 OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i = 10.5 ± 1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i = 9, c =6 10 µa /32
21 ELECTRICAL CHARACTERISTICS FOR LF90AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = I o =50mA, i = 11-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i =10to16, I o = 5 ma 9 45 m o Load Regulation i = 10.3 I o = 5 to 500 ma 9 45 m i =10to16 Io=0mA 1.5 ma i = 10.3 to 16 I o =500mA OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =11±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i =10, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF90C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i = I o =50mA, i = 11-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i =10to16, I o = 5 ma 9 45 m o Load Regulation i = 10.3 I o = 5 to 500 ma 9 45 m i =10to16 Io=0mA 1.5 ma i = 10.3 to 16 I o =500mA OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =11±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i =10, c =6 10 µa /32
22 ELECTRICAL CHARACTERISTICS FOR LF120AB (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =15 I o =50mA, i = 15-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i =13to16, I o = 5 ma 12 m o Load Regulation i = 13.3 I o = 5 to 500 ma 12 m i =13to16 Io=0mA 1.5 ma i = 13.3 to 16 I o =500mA OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =14±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i =13, c =6 10 µa C O Output Bypass Capacitance ESR = 0.1 to 10 Ω Io = 0 to 500 ma 2 10 µf ELECTRICAL CHARACTERISTICS FOR LF120C (refer to the test circuits, Tj =25 o C, o Output oltage I o =50mA, i =14 I o =50mA, i = 14-25<T a <85 o C i Operating Input oltage 16 o Line Regulation i =13to16, I o = 5 ma 12 m o Load Regulation i = 13.3 I o = 5 to 500 ma 12 m i =13to16 Io=0mA 1.5 ma i = 13.3 to 16 I o =500mA OFF MODE i = µa SR Supply oltage Rejection I o = 5 ma i =14±1 en Output Noise oltage B = 10 Hz to 100 KHz 50 µ d Dropout oltage I o = 200 ma il Control Input Logic Low -40 < T a <125 o C 0.8 ih Control Input Logic High -40 < T a <125 o C 2 I i Control Input Current i =13, c =6 10 µa /32
23 TYPICAL PERFORMANCE CHARACTERISTICS Dropout oltage vs Output Current Dropout oltage vs Temperature Supply Current vs Input oltage Supply Current vs Input oltage Short Circuit Current vs Input oltage Supply Current vs Temperature 23/32
24 Logic Controlled Precision 3.3/5.0 Selectable Output Sequential Multi-Output Supply 24/32
25 Multiple Supply With ON/OFF Toggle Switch Basic Inhibit Functions 25/32
26 Delayed Turn-On Low oltage Bulb Blinker 26/32
27 PENTAWATT (ERTICAL) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A C D D E F F G G H H L L L L L L L M M Dia P010E 27/32
28 TO-220 MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A C D D E F F G H H L L L L L Dia P011D 28/32
29 TO-220FP MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A B D E F F F G G H L L L L L Ø H G B D A E L6 L7 L3 F1 F F2 G L2 L4 P011G4/B 29/32
30 TO-252 (DPAK) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A A A B B C C D E G H L L H L2 D E = = B2 = = G = = C2 B A DETAIL A C A1 A2 DETAIL A L B 30/32
31 PPAK MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A A A B B C C D E G G H L L /B 31/32
32 Information furnished isbelieved to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. Thispublication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 32/ STMicroelectronics Printed in Italy All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
L4940 series VERY LOW DROP 1.5 A REGULATORS
L4940 series VERY LOW DROP 1.5 A REGULATORS PRECISE 5 V, 8.5 V, 10 V, 12 V OUTPUTS LOW DROPOUT VOLTAGE (500 typ at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
Symbol Parameter Value Unit V i-o Input-output Differential Voltage 40 V I O Output Current Intenrally Limited Top
LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE : 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 1.5A 0.1% LINE AND LOAD REGULATION FLOATING OPERATION FOR HIGH VOLTAGES COMPLETE SERIES OF PROTECTIONS
ADJUSTABLE VOLTAGE AND CURRENT REGULATOR
L200 ADJUSTABLE VOLTAGE AND CURRENT REGULATOR ADJUSTABLE OUTPUT CURRENT UP TO 2 A (GUARANTEED UP TO Tj = 150 C) ADJUSTABLE OUTPUT VOLTAGE DOWN TO 2.85 V INPUT OVERVOLTAGE PROTECTION (UP TO 60 V, 10 ms)
Description SO-8. series. Furthermore, in the 8-pin configuration Very low-dropout voltage (0.2 V typ.)
ery low-dropout voltage regulator with inhibit function TO-92 Bag TO-92 Tape and reel Ammopack 1 2 3 SO-8 Description Datasheet - production data The is a very low-dropout voltage regulator available in
L78M00 SERIES POSITIVE VOLTAGE REGULATORS. www.tvsat.com.pl
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 0.5A OUTPUT VOLTAGES OF 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSISTOR SOA PROTECTION DESCRIPTION
.OPERATING SUPPLY VOLTAGE UP TO 46 V
L298 DUAL FULL-BRIDGE DRIVER.OPERATING SUPPLY VOLTAGE UP TO 46 V TOTAL DC CURRENT UP TO 4 A. LOW SATURATION VOLTAGE OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V (HIGH NOISE IMMUNITY)
Description. Table 1. Device summary. Order codes. TO-220 (single gauge) TO-220 (double gauge) D²PAK (tape and reel) TO-220FP
1.2 V to 37 V adjustable voltage regulators Description Datasheet - production data TO-220 TO-220FP The LM217, LM317 are monolithic integrated circuits in TO-220, TO-220FP and D²PAK packages intended for
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIE OR GATE MEDIUM-SPEED OPERATION t PHL = t PLH = 70ns (Typ.) at CL = 50 pf and DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
HCF4081B QUAD 2 INPUT AND GATE
QUAD 2 INPUT AND GATE MEDIUM SPEED OPERATION : t PD = 60ns (Typ.) at 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A = 25
TDA2822 DUAL POWER AMPLIFIER SUPPLY VOLTAGE DOWN TO 3 V LOW CROSSOVER DISTORSION LOW QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION
TDA2822 DUAL POER AMPLIFIER SUPPLY VOLTAGE DON TO 3 V. LO CROSSOVER DISTORSION LO QUIESCENT CURRENT BRIDGE OR STEREO CONFIGURATION DESCRIPTION The TDA2822 is a monolithic integrated circuit in 12+2+2 powerdip,
Description. Table 1. Device summary
2 A positive voltage regulator IC Description Datasheet - production data Features TO-220 Output current up to 2 A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24 V Thermal protection Short circuit protection
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS. OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY
L293B L293E PUSH-PULL FOUR CHANNEL DRIVERS OUTPUT CURRENT 1A PER CHANNEL PEAK OUTPUT CURRENT 2A PER CHANNEL (non repetitive) INHIBIT FACILITY. HIGH NOISE IMMUNITY SEPARATE LOGIC SUPPLY OVERTEMPERATURE
HCF4056B BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION
BCD TO 7 SEGMENT DECODER /DRIVER WITH STROBED LATCH FUNCTION QUIESCENT CURRENT SPECIF. UP TO 20V OPERATION OF LIQUID CRYSTALS WITH CMOS CIRCUITS PROVIDES ULTRA LOW POWER DISPLAY. EQUIVALENT AC OUTPUT DRIVE
BUX48/48A BUV48A/V48AFI
BUX48/48A BU48A/48AFI HIGH POWER NPN SILICON TRANSISTORS STMicroelectronics PREFERRED SALESTYPES NPN TRANSISTOR HIGH OLTAGE CAPABILITY HIGH CURRENT CAPABILITY FAST SWITCHING SPEED APPLICATIONS SWITCH MODE
L7800 SERIES POSITIVE VOLTAGE REGULATORS
SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5 A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
HCF4001B QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE PROPAGATION DELAY TIME: t PD = 50ns (TYP.) at V DD = 10V C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS OUTPUT SWITCH CURRENT IN EXCESS OF 1.5A 2% REFERENCE ACCURACY LOW QUIESCENT CURRENT: 2.5mA (TYP.) OPERATING FROM 3V TO 40V FREQUENCY OPERATION TO 100KHz
TDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
Symbol Parameter Value Unit V DS Drain-source Voltage (V GS =0) 50 V V DGR Drain- gate Voltage (R GS =20kΩ) 50 V
BUZ71A N - CHANNEL 50V - 0.1Ω - 13A TO-220 STripFET POWER MOSFET TYPE V DSS R DS(on) I D BUZ71A 50 V < 0.12 Ω 13 A TYPICAL RDS(on) = 0.1 Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED HIGH CURRENT
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET
STP80NF55-08 STB80NF55-08 STB80NF55-08-1 N-CHANNEL 55V - 0.0065 Ω - 80A D2PAK/I2PAK/TO-220 STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STB80NF55-08/-1 STP80NF55-08 55 V 55 V
LM337. Three-terminal adjustable negative voltage regulators. Features. Description
Three-terminal adjustable negative voltage regulators Datasheet - production data current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional
STGW40NC60V N-CHANNEL 50A - 600V - TO-247 Very Fast PowerMESH IGBT
N-CHANNEL 50A - 600V - TO-247 Very Fast PowerMESH IGBT Table 1: General Features STGW40NC60V 600 V < 2.5 V 50 A HIGH CURRENT CAPABILITY HIGH FREQUENCY OPERATION UP TO 50 KHz LOSSES INCLUDE DIODE RECOVERY
ULN2801A, ULN2802A, ULN2803A, ULN2804A
ULN2801A, ULN2802A, ULN2803A, ULN2804A Eight Darlington array Datasheet production data Features Eight Darlington transistors with common emitters Output current to 500 ma Output voltage to 50 V Integral
LM833 LOW NOISE DUAL OPERATIONAL AMPLIFIER
LOW NOISE DUAL OPERATIONAL AMPLIFIER LOW VOLTAGE NOISE: 4.5nV/ Hz HIGH GAIN BANDWIDTH PRODUCT: 15MHz HIGH SLEW RATE: 7V/µs LOW DISTORTION:.2% EXCELLENT FREQUENCY STABILITY ESD PROTECTION 2kV DESCRIPTION
STP62NS04Z N-CHANNEL CLAMPED 12.5mΩ - 62A TO-220 FULLY PROTECTED MESH OVERLAY MOSFET
N-CHANNEL CLAMPED 12.5mΩ - 62A TO-220 FULLY PROTECTED MESH OVERLAY MOSFET TYPE V DSS R DS(on) I D STP62NS04Z CLAMPED
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME: t PD = 50ns (Typ.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
TDA4605 CONTROL CIRCUIT FOR SWITCH MODE POWER SUPPLIES USING MOS TRANSISTORS
CONTROL CIRCUIT FOR SWITCH MODE POWER SUPPLIES USING MOS TRANSISTORS Fold-Back Characteristic provides Overload Protection for External Diodes Burst Operation under Short-Circuit and no Load Conditions
STP6NK60Z - STP6NK60ZFP STB6NK60Z - STB6NK60Z-1 N-CHANNEL 600V - 1Ω - 6A TO-220/TO-220FP/D 2 PAK/I 2 PAK Zener-Protected SuperMESH Power MOSFET
STP6NK60Z - STP6NK60ZFP STB6NK60Z - STB6NK60Z-1 N-CHANNEL 600V - 1Ω - 6A TO-220/TO-220FP/D 2 PAK/I 2 PAK Zener-Protected SuperMESH Power MOSFET TYPE V DSS R DS(on) I D Pw STP6NK60Z STP6NK60ZFP STB6NK60Z
STP10NK60Z/FP, STB10NK60Z/-1 STW10NK60Z N-CHANNEL 600V-0.65Ω-10A TO-220/FP/D 2 PAK/I 2 PAK/TO-247 Zener-Protected SuperMESH Power MOSFET
STP10NK60Z/FP, STB10NK60Z/-1 STW10NK60Z N-CHANNEL 600V-0.65Ω-10A TO-220/FP/D 2 PAK/I 2 PAK/TO-247 Zener-Protected SuperMESH Power MOSFET TYPE V DSS R DS(on) I D Pw STP10NK60Z STP10NK60ZFP STB10NK60Z STB10NK60Z-1
STW20NM50 N-CHANNEL 550V @ Tjmax - 0.20Ω - 20ATO-247 MDmesh MOSFET
N-CHANNEL 550V @ Tjmax - 0.20Ω - 20ATO-247 MDmesh MOSFET TYPE V DSS (@Tjmax) R DS(on) I D STW20NM50 550V < 0.25Ω 20 A TYPICAL R DS (on) = 0.20Ω HIGH dv/dt AND AVALANCHE CAPABILITIES 100% AVALANCHE TESTED
.LOW POWER DISSIPATION .HIGH NOISE IMMUNITY M74HC154 4 TO 16 LINE DECODER/DEMULTIPLEXER. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V
. HIGH SPEED tpd = 15 ns (TYP.) at VCC =5V.LOW POWER DISSIPATION I CC =4µA (MAX.) at T A =25 C.HIGH NOISE IMMUNITY VNIH =VNIL =28%VCC (MIN.) OUTPUT DRIVE CAPABILITY 15 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE
HCC/HCF4032B HCC/HCF4038B
HCC/HCF4032B HCC/HCF4038B TRIPLE SERIAL ADDERS INERT INPUTS ON ALL ADDERS FOR SUM COMPLEMENTING APPLICATIONS FULLY STATIC OPERATION...DC TO 10MHz (typ.) @ DD = 10 BUFFERED INPUTS AND OUTPUTS SINGLE-PHASE
SWITCH-MODE POWER SUPPLY CONTROLLER PULSE OUTPUT DC OUTPUT GROUND EXTERNAL FUNCTION SIMULATION ZERO CROSSING INPUT CONTROL EXTERNAL FUNCTION
SWITCH-MODE POWER SUPPLY CONTROLLER. LOW START-UP CURRENT. DIRECT CONTROL OF SWITCHING TRAN- SISTOR. COLLECTOR CURRENT PROPORTIONAL TO BASE-CURRENT INPUT REERSE-GOING LINEAR OERLOAD CHARACTERISTIC CURE
TDA2003 10W CAR RADIO AUDIO AMPLIFIER
TDA2003 10W CAR RADIO AUDIO AMPLIFIER DESCRIPTION The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external
ST202 5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS
5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS SUPPLY VOLTAGE RANGE: 4.5 TO 5.5V SUPPLY CURRENT NO LOAD (TYP): 1.5mA TRASMITTER OUTPUT VOLTAGE SWING (TYP): ± 9V TRANSITION SLEW RATE (TYP.): 12V/µs
HCF4028B BCD TO DECIMAL DECODER
BCD TO DECIMAL DECODER BCD TO DECIMAL DECODING OR BINARY TO OCTAL DECODING HIGH DECODED OUTPUT DRIVE CAPABILITY "POSITIVE LOGIC" INPUTS AND OUTPUTS: DECODED OUTPUTS GO HIGH ON SELECTION MEDIUM SPEED OPERATION
Obsolete Product(s) - Obsolete Product(s)
SYNCHRONOUS PROGRAMMABLE 4-BIT BINARY COUNTER WITH ASYNCHRONOUS CLEAR INTERNAL LOOK-AHEAD FOR FAST COUNTING CARRY OUTPUT FOR CASCADING SYNCHRONOUSLY PROGRAMMABLE LOW-POWER TTL COMPATIBILITY STANDARDIZED
Symbol Parameter Value Unit IAR Avalanche Current, Repetitive or Not-Repetitive
BUZ11 N - CHANNEL 50V - 0.03Ω - 30A -TO-220 STripFET POWER MOSFET TYPE V DSS R DS(on) I D BUZ11 50 V < 0.04 Ω 30 A TYPICAL R DS(on) = 0.03 Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED HIGH CURRENT
STW34NB20 N-CHANNEL 200V - 0.062 Ω - 34A TO-247 PowerMESH MOSFET
N-CHANNEL 200V - 0.062 Ω - 34A TO-247 PowerMESH MOSFET Table 1. General Features Figure 1. Package Type V DSS R DS(on) I D STW34NB20 200 V < 0.075 Ω 34 A FEATURES SUMMARY TYPICAL R DS(on) = 0.062 Ω EXTREMELY
VNP5N07 "OMNIFET": FULLY AUTOPROTECTED POWER MOSFET
"OMNIFET": FULLY AUTOPROTECTED POWER MOSFET TYPE Vclamp RDS(on) Ilim VNP5N07 70 V 0.2 Ω 5 A LINEAR CURRENT LIMITATION THERMAL SHUT DOWN SHORT CIRCUIT PROTECTION INTEGRATED CLAMP LOW CURRENT DRAWN FROM
TL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
STLQ015. 150 ma, ultra low quiescent current linear voltage regulator. Description. Features. Application
150 ma, ultra low quiescent current linear voltage regulator Description Datasheet - production data Features SOT23-5L Input voltage from 1.5 to 5.5 V Very low quiescent current: 1.0 µa (typ.) at no load
L4970A 10A SWITCHING REGULATOR
10A SWITCHING REGULATOR 10A OUTPUT CURRENT 5.1 TO 40 OUTPUT OLTAGE RANGE 0 TO 90% DUTY CYCLE RANGE INTERNAL FEED-FORWARD LINE REGULA- TION INTERNAL CURRENT LIMITING PRECISE 5.1 ± 2% ON CHIP REFERENCE RESET
L6234. Three phase motor driver. Features. Description
Three phase motor driver Features Supply voltage from 7 to 52 V 5 A peak current R DSon 0.3 Ω typ. value at 25 C Cross conduction protection TTL compatible driver Operating frequency up to 150 khz Thermal
HCC4541B HCF4541B PROGRAMMABLE TIMER
HCC4541B HCF4541B PROGRAMMABLE TIMER 16 STAGE BINARI COUNTER LOW SYMMETRICAL OUTPUT RESISTANCE, TYPICALLY 100 OHM AT DD = 15 OSCILLATOR FREQUENCY RANGE : DC TO 100kHz AUTO OR MASTER RESET DISABLES OSCIL-
L297 STEPPER MOTOR CONTROLLERS
L297 STEPPER MOTOR CONTROLLERS NORMAL/WAVE DRIVE HALF/FULL STEP MODES CLOCKWISE/ANTICLOCKWISE DIRECTION SWITCHMODE LOAD CURRENT REGULA- TION PROGRAMMABLE LOAD CURRENT FEW EXTERNAL COMPONENTS RESET INPUT
IRF740 N-CHANNEL 400V - 0.46Ω - 10A TO-220 PowerMESH II MOSFET
N-CHANNEL 400V - 0.46Ω - 10A TO-220 PowerMESH II MOSFET TYPE V DSS R DS(on) I D IRF740 400 V < 0.55 Ω 10 A TYPICAL R DS (on) = 0.46Ω EXCEPTIONAL dv/dt CAPABILITY 100% AVALANCHE TESTED LOW GATE CHARGE VERY
SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS
SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1 % 100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME CONTROL INTERNAL
ULN2001, ULN2002 ULN2003, ULN2004
ULN2001, ULN2002 ULN2003, ULN2004 Seven Darlington array Datasheet production data Features Seven Darlingtons per package Output current 500 ma per driver (600 ma peak) Output voltage 50 V Integrated suppression
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP
STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP N-channel 600 V - 1.76 Ω - 4 A SuperMESH Power MOSFET DPAK - D 2 PAK - IPAK - I 2 PAK - TO-220 - TO-220FP Features Type V DSS R DS(on)
IRFP450. N - CHANNEL 500V - 0.33Ω - 14A - TO-247 PowerMESH MOSFET
IRFP450 N - CHANNEL 500V - 0.33Ω - 14A - TO-247 PowerMESH MOSFET TYPE V DSS R DS(on) I D IRFP450 500 V < 0.4 Ω 14 A TYPICAL R DS(on) = 0.33 Ω EXTREMELY HIGH dv/dt CAPABILITY 100% AVALANCHE TESTED VERY
IRF830. N - CHANNEL 500V - 1.35Ω - 4.5A - TO-220 PowerMESH MOSFET
IRF830 N - CHANNEL 500V - 1.35Ω - 4.5A - TO-220 PowerMESH MOSFET TYPE V DSS R DS(on) I D IRF830 500 V < 1.5 Ω 4.5 A TYPICAL R DS(on) = 1.35 Ω EXTREMELY HIGH dv/dt CAPABILITY 100% AVALANCHE TESTED VERY
TDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description
10 + 10 W stereo amplifier for car radio Features Low distortion Low noise Protection against: Output AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground
2STBN15D100. Low voltage NPN power Darlington transistor. Features. Application. Description
Low voltage NPN power Darlington transistor Features Good h FE linearity High f T frequency Monolithic Darlington configuration with integrated antiparallel collector-emitter diode TAB Application Linear
BTB04-600SL STANDARD 4A TRIAC MAIN FEATURES
BTB-6SL STANDARD A TRIAC MAIN FEATURES A Symbol Value Unit I T(RMS) A V DRM /V RRM 6 V I GT(Q) ma G A A DESCRIPTION The BTB-6SL quadrants TRIAC is intended for general purpose applications where high surge
STP60NF06FP. N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 30A TO-220FP STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06FP 60V
TL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
TDA7448 6 CHANNEL VOLUME CONTROLLER 1 FEATURES 2 DESCRIPTION. Figure 1. Package
6 CHANNEL CONTROLLER FEATURES 6 CHANNEL INPUTS 6 CHANNEL OUTPUTS ATTENUATION RANGE OF 0 TO -79dB CONTROL IN.0dB STEPS 6 CHANNEL INDEPENDENT CONTROL ALL FUNCTION ARE PROGRAMMABLE VIA SERIAL BUS DESCRIPTION
LM134-LM234-LM334. Three terminal adjustable current sources. Features. Description
Three terminal adjustable current sources Features Operates from 1V to 40V 0.02%/V current regulation Programmable from 1µA to 10mA ±3% initial accuracy Description The LM134/LM234/LM334 are 3-terminal
BD135 - BD136 BD139 - BD140
BD135 - BD136 BD139 - BD140 Complementary low voltage transistor Features Products are pre-selected in DC current gain Application General purpose Description These epitaxial planar transistors are mounted
LM217M, LM317M. Medium current 1.2 to 37 V adjustable voltage regulator. Description. Features
Medium current 1.2 to 37 V adjustable voltage regulator Datasheet - production data Description The LM217M and LM317M are monolithic integrated circuits in DPAK package used as positive adjustable voltage
STCS1A. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3 x 3
CLASS-D VERTICAL DEFLECTION AMPLIFIER FOR TV AND MONITOR APPLICATION OUT CFLY + CFLY - BOOT VREG FEEDCAP FREQ. July 2001 1/8
CLASS-D VERTICAL DEFLECTION AMPLIFIER FOR TV AND MONITOR APPLICATION FEATURES PRELIMINARY DATA HIGH EFFICIENCY POWER AMPLIFIER NO HEATSINK SPLIT SUPPLY INTERNAL FLYBACK GENERATOR OUTPUT CURRENT UP TO.5
. MEDIUM SPEED OPERATION - 8MHz (typ.) @ . MULTI-PACKAGE PARALLEL CLOCKING FOR HCC4029B HCF4029B PRESETTABLE UP/DOWN COUNTER BINARY OR BCD DECADE
HCC4029B HCF4029B PRESETTABLE UP/DOWN COUNTER BINARY OR BCD DECADE. MEDIUM SPEED OPERATION - 8MHz (typ.) @ CL = 50pF AND DD-SS = 10. MULTI-PACKAGE PARALLEL CLOCKING FOR SYNCHRONOUS HIGH SPEED OUTPUT RES-
BD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
BD238. Low voltage PNP power transistor. Features. Applications. Description. Low saturation voltage PNP transistor
Low voltage PNP power transistor Features Low saturation voltage PNP transistor Applications Audio, power linear and switching applications Description The device is manufactured in planar technology with
STCS1. 1.5 A max constant current LED driver. Features. Applications. Description
1.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 1.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic DFN8 (3x3 mm)
Obsolete Product(s) - Obsolete Product(s)
32 W hi-fi audio power amplifier Features High output power (50 W music power IEC 268.3 rules) High operating supply voltage (50 V) Single or split supply operations Very low distortion Short-circuit protection
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu.
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. 2N3055, MJ2955 Complementary power transistors Features Datasheet - production
LM134-LM234 LM334 THREE TERMINAL ADJUSTABLE CURRENT SOURCES. OPERATES from 1V to 40V
LM134-LM234 LM334 THREE TERMINAL USTABLE CURRENT SOURCES OPERATES from 1 to 40. 0.02% CURRENT REGULATION PROGRAMMABLE from 1µA to 10mA ±3% INITIAL ACCURACY DESCRIPTION The LM134/LM234/LM334 are 3-terminal
ST13005. High voltage fast-switching NPN power transistor. Features. Applications. Description
High voltage fast-switching NPN power transistor Datasheet production data Features Low spread of dynamic parameters Minimum lot-to-lot spread for reliable operation Very high switching speed Applications
STP60NF06. N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-channel 60V - 0.014Ω - 60A TO-220 STripFET II Power MOSFET General features Type V DSS R DS(on) I D STP60NF06 60V
Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully
VN03. ISO high side smart power solid state relay PENTAWATT. Features. Description. www.tvsat.com.pl
ISO high side smart power solid state relay Features Type V DSS R DS(on) I n (1) Maximum continuous output current (a) : 4A @ Tc= 25 C 5V logic level compatible input Thermal shutdown Under voltage protection
HCC/HCF4027B DUAL-J-K MASTER-SLAVE FLIP-FLOP
DUAL-J-K MASTER-SLAVE FLIP-FLOP. SET-RESET CAPABILITY STATIC FLIP-FLOP OPERATION - RETAINS STATE INDEFINITELY WITH CLOCK LEVEL EITHER HIGH OR LOW MEDIUM SPEED OPERATION - 16MHz (typ. clock toggle rate
STP10NK80ZFP STP10NK80Z - STW10NK80Z
STP10NK80ZFP STP10NK80Z - STW10NK80Z N-channel 800V - 0.78Ω - 9A - TO-220/FP-TO-247 Zener-protected supermesh TM MOSFET General features Type V DSS R DS(on) I D Pw STP10NK80Z 800V
. HIGH SPEED .LOW POWER DISSIPATION .COMPATIBLE WITH TTL OUTPUTS M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. tpd = 9 ns (TYP.
M54HCT27 M74HCT27 TRIPLE 3-INPUT NOR GATE. HIGH SPEED tpd = 9 ns (TYP.) AT VCC =5V.LOW POWER DISSIPATION I CC =1µA (MAX.) AT T A =25 C.COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT
UA741. General-purpose single operational amplifier. Features. Applications. Description. N DIP8 (plastic package)
General-purpose single operational amplifier Datasheet - production data N DIP8 (plastic package) D SO8 (plastic micropackage) Pin connections (top view) 1 - Offset null 1 2 - Inverting input 3 - Non-inverting
DDSL01. Secondary protection for DSL lines. Features. Description
Secondary protection for DSL lines Features Stand off voltage: 30 V Surge capability: I pp = 30 A 8/20 µs Low capacitance device: 4.5 pf at 2 V RoHS package Low leakage current: 0.5 µa at 25 C 3 2 Description
TDA7318D DIGITAL CONTROLLED STEREO AUDIO PROCESSOR
TDA738 DIGITAL CONTROLLED STEREO AUDIO PROCESSOR INPUT MULTIPLEXER: - 4 STEREO INPUTS - SELECTABLE INPUT GAIN FOR OPTIMAL ADAPTION TO DIFFERENT SOURCES INPUT AND OUTPUT FOR EXTERNAL EQUALIZER OR NOISE
MC34063AB, MC34063AC, MC34063EB, MC34063EC
MC34063AB, MC34063AC, MC34063EB, MC34063EC DC-DC converter control circuits Description Datasheet - production data Features DIP-8 SO-8 Output switch current in excess of 1.5 A 2 % reference accuracy Low
MC33079. Low noise quad operational amplifier. Features. Description
Low noise quad operational amplifier Datasheet production data Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion: 0.002% Large output voltage
TDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
STCS2A. 2 A max constant current LED driver. Features. Applications. Description
2 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 2 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic Slope control with
Order code Temperature range Package Packaging
ST485B ST485C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver maintains high impedance
STOD2540. PMOLED display power supply. Features. Application. Description
PMOLED display power supply Features Inductor switches boost controller PFM mode control High efficiency over wide range of load (1 ma to 40 ma) Integrated load disconnect switch Over voltage protection
STP6N60FI N - CHANNEL ENHANCEMENT MODE POWER MOS TRANSISTOR
N - CHANNEL ENHANCEMENT MODE POWER MOS TRANSISTOR TYPE VDSS RDS(on) ID STP6N60FI 600 V < 1.2 Ω 3.8 A TYPICAL R DS(on) =1Ω AVALANCHE RUGGED TECHNOLOGY 100% AVALANCHE TESTED REPETITIVE AVALANCHE DATA AT
STP55NF06L STB55NF06L - STB55NF06L-1
General features STP55NF06L STB55NF06L - STB55NF06L-1 N-channel 60V - 0.014Ω - 55A TO-220/D 2 PAK/I 2 PAK STripFET II Power MOSFET Type V DSS R DS(on) I D STP55NF06L 60V
VN05N. High side smart power solid state relay PENTAWATT. Features. Description
High side smart power solid state relay Features Type V DSS R DS(on) I OUT V CC VN05N 60 V 0.18 Ω 13 A 26 V Output current (continuous): 13A @ Tc=25 C 5V logic level compatible input Thermal shutdown Under
STP16NF06L STP16NF06LFP
STP16NF06L STP16NF06LFP N-CHNNEL 60V - 0.07 Ω - 16 TO-220/TO-220FP STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STP16NF06L STP60NF06LFP 60 V 60 V
MC78XX/LM78XX. 3-terminal 1A positive voltage regulator. Features. Description. Internal Block Digram. www.fairchildsemi.com
www.fairchildsemi.com 3-terminal 1A positive voltage regulator Features Current up to 1A Voltages of 5, 6, 8, 9, 10, 11, 12, 15, 18, 24V Thermal Overload Protection Short Circuit Protection Transistor
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
STN3NF06L. N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET. Features. Application. Description
N-channel 60 V, 0.07 Ω, 4 A, SOT-223 STripFET II Power MOSFET Features Type V DSS (@Tjmax) Exceptional dv/dt capability Avalanche rugged technology 100% avalanche tested R DS(on) max STN3NF06L 60 V < 0.1
LM135-LM235-LM335. Precision temperature sensors. Features. Description
Precision temperature sensors Features Directly calibrated in K 1 C initial accuracy Operates from 450µA to 5mA Less than 1Ω dynamic impedance TO-92 (Plastic package) Description The LM135, LM235, LM335
STB75NF75 STP75NF75 - STP75NF75FP
STB75NF75 STP75NF75 - STP75NF75FP N-channel 75V - 0.0095Ω - 80A - TO-220 - TO-220FP - D 2 PAK STripFET II Power MOSFET General features Type V DSS R DS(on) I D STB75NF75 75V
STGB10NB37LZ STGP10NB37LZ
STGB10NB37LZ STGP10NB37LZ 10 A - 410 V internally clamped IGBT Features Low threshold voltage Low on-voltage drop Low gate charge TAB TAB High current capability High voltage clamping feature Applications
BTA40, BTA41 and BTB41 Series
BTA4, BTA41 and BTB41 Series STANDARD 4A TRIACS Table 1: Main Features Symbol Value Unit I T(RMS) 4 A V DRM /V RRM 6 and 8 V I T (Q1 ) 5 ma DESCRIPTION Available in high power packages, the BTA/ BTB4-41
L78. Positive voltage regulator ICs. Description. Features
Positive voltage regulator ICs Description Datasheet - production data TO-220 Features DPAK TO-220FP D²PAK Output current up to 1.5 A Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V Thermal overload
FLC21-135A LOW POWER FIRE LIGHTER CIRCUIT. Application Specific Discretes A.S.D.
Application Specific iscretes A.S.. LC21-135A LOW POWER IRE LIGHTER CIRCUIT EATURES EICATE THYRISTOR STRUCTURE OR CAPACITIVE ISCHARGE IGNITION OPERATION HIGH PULSE CURRENT CAPABILITY I RM =90A @ tp=10µs