GENERIC. Installation / Configuration Manual. T300 Transmitter R160 Receiver D160 Expansion Module. Revised February 9, 2007.

Transcription

1 GENERIC Installation / Configuration Manual T300 Transmitter R160 Receiver D160 Expansion Module Revised February 9, 2007 Version 5 DMAN - xxxx - xx # Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604) Fax# (604) Toll Free

2 Table of Contents System Overview...3 Features...3 T300 Dimensions and Controls...3 Installing the Receiver...4 Receiver Dimensions...4 Installing the Expansion Module...5 Installation Considerations...6 Power the Transmitter...6 Test the Transmitter / Receiver Link...7 Download ID Code...7 Calibrating Proportional Controls...9 Diagnostics T300 Transmitter...10 Diagnostics D160 Expansion Module...10 Diagnostics R160 Receiver...11 Troubleshooting Guide...12 Parts & Accessories...16 Specifications...16 Warranty Information...16 NOTE: These instructions are intended only for installing and operating the remote control equipment described here. This is not a complete Operator s Manual. For complete operating instructions, please read the Operator s Manual appropriate for your particular machine. Safety Precautions READ ALL INSTRUCTIONS CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Failure to follow the SAFETY PRECAUTIONS may result in radio equipment failure and serious personal injury Installation PROVIDE A SAFETY CUTOFF SWITCH. If maintenance is required, the radio must be disconnected from power USE PROPER WIRING. Loose or frayed wires can cause system failure, intermittent operation, machine damage, etc. DO NOT INSTALL IN HOT AREAS. This apparatus can be damaged by heat in excess of 158 F (70 C) Personal Safety MAKE SURE MACHINERY AND SURROUNDING AREA IS CLEAR BEFORE OPERATING. Do not activate the remote system unless it is safe to do so. TURN OFF THE RECEIVER POWER BEFORE WORKING ON MACHINERY. Always disconnect the remote system before doing any maintenance to prevent accidental operation of the machine Care KEEP DRY. Do not clean the transmitter / receiver under high pressure. If water or other liquids get inside the transmitter battery or receiver compartment, immediately dry the unit. Remove the case and let the unit air dry CLEAN THE UNIT AFTER OPERATION. Remove any mud, dirt, concrete, etc. from the unit to prevent clogging of buttons, switches, etc. by using a damp cloth. Maintenance / Welding DISCONNECT THE RADIO RECEIVER BEFORE WELDING on the machine the receiver is connected to. Failure to disconnect will result in the destruction of the radio receiver. 2

3 System Overview The ORIGA T300 / R160 / D160 is a portable, long range, programmable radio remote control system. Designed as a compact and easy-to-use product, this member of the ORIGA family puts complete control of your crane where it s needed most, with the operator. It s robust, easy to install and has complete self-diagnostics. This system can be a simple cable replacement or add intelligence to make it a total control package. It s a radio, a PLC and a valve driver all in one. The ORIGA T300 / R160 / D160 system uses Frequency Hopping Spread Spectrum (FHSS) technology. FHSS devices concentrate their full power into a very narrow signal that randomly hops from frequency to frequency within a designated band. This transmission pattern, along with CRC-16 error-checking techniques, enables signals to overcome interference that commonly affects licensed radios. The R160 receiver is designed to be powered from a 12VDC or 24VDC system. It features 19 solid state, high-side driver input / output controls and a reliable E-Stop control. The D160 Expansion Unit has up to 19 input/output (including 2 proportional) combinations, PWM, or voltage outputs, or a combination of these types. The T300 transmitter comes with up to sixteen proportional and sixteen digital controls. The T300 can accommodate up to eight single axis paddles, eight three-position switches and a re-settable E-Stop. A unique ID code is used by each T300 to ensure that no two systems will conflict on a job site. Features FCC, ISC, CE approved License free 1200 foot 900 MHz ( GHz) Compact / weatherproof / ergonomic Simple wire-and-use installation Resilient to impact and shock Available in both 900 MHz and 2.4 GHz Available with paddles and/or joysticks for proportional control Available with an optional pendant cable Factory configurable for all custom applications. R160 Receiver T300 Transmitter T300 Dimensions and Controls Power / calibration switch Switches 2-8 D160 Module E-Stop Pendant con- 6.0 Battery/ Pendant LED Active LED E-Stop LED Paddles

4 Installing the Receiver Use the Wiring Diagram and the Connector Diagram below to connect the receiver pins directly to the appropriate contacts of the machine electronics. R160 Output Cables can be provided with every system to simplify the wiring process. The Wire Color column below only applies to the OMNEX Output Cable configuration. Tips on mounting, power connections and filtering are also provided under Installation Considerations. Wiring Diagram Pin-Output Wire Colors Functions Notes B7 B8 B12-19 B11-18 B10-17 A1-16 A2-15 A4-14 Black/Red White/Black Blue/White Blue/Black Black/White Green/Black Factory Configurable Only Factory Configurable Only B9-13 B6-12 B5-11 B4-10 B3-9 B2-8 B1-7 A12-6 A10-5 A11-4 A9-3 A8-2 A7-1 Red/White Orange White Green/Black/White Green Red/Black/White White/Red/Black Orange/Red Orange/Black Blue/Red White/Red Red/Green Orange/Green * * ** ** A5 A6 A3 Black/White/Red Red Black Switches to Power with Link Power Input (+9V to 30VDC) Ground Note: Enable output: On when the T300 "Enable" switch is on. Outputs: 19 solid state, high-side driver outputs, 5A max. per pin and 7A max per bank, total combined current 15A Inputs: All output pins can be factory configured as inputs. Input pins should be connected to a current limiting (fused) source Connector Pin Assignments Connectors as seen from under the receiver R160 / D160 Dimensions ES FA L STA 5.13 A 4.00 B 4

5 Installing the Expansion Module Use the Wiring Diagram and the Connector Diagram below to connect the Expansion module pins directly to the appropriate contacts of the machine electronics. D160 Output Cables are provided with every system to simplify the wiring process. The Wire Color column below only applies to the OMNEX Output Cable configuration. Tips on mounting, power connections and filtering are also provided under Installation Considerations. Wiring Diagram D160 Module Internal Wiring Pin-Output B7 B8 Wire Colors Functions Factory Configurable Only Factory Configurable Only Notes B12-19 B11-18 B10-17 A1-16 Black/Red White/Black Blue/White Blue/Black A2-15 A4-14 Black/White Green/Black B9-13 B6-12 B5-11 B4-10 B3-9 B2-8 B1-7 A12-6 A10-5 A11-4 A9-3 A8-2 A7-1 Red/White Orange White Green/Black/White Green Red/Black/White White/Red/Black Orange/Red Orange/Black Blue/Red White/Red Red/Green Orange/Green A5 Black/White/Red Switches to Power with Link A6 A3 Red Black Power Input (+9V to 30VDC) Ground Outputs: 19 solid state, high-side driver outputs, 5A max. each, total combined current 15A Inputs: All output pins can be factory configured as inputs. Special Functions 5

6 Installation Considerations NOTE: The FCC and ISC require that the antenna be restricted to that supplied by the manufacturer and approved for use with this product. An optional 0dB coax wire antenna may be supplied. For other antenna options, please contact OMNEX Control Systems ULC Mounting and Installation The receiver can be mounted by fastening two ¼ bolts through the two mounting holes in the unit s enclosure. When mounting, ensure that the receiver is oriented so that the text is reading right and the connectors pointing down. When selecting a mounting point for the receiver, it is recommended that the location require only a minimal length of wiring to connect it to the control panel, that it will be in a visible area where it has good exposure to the operator and that it is mounted on a surface that sustains minimal vibration. It is also recommended that the receiver have the best possible line of sight with the transmitter Power Connections and Wiring Whenever a power connection is made to an electronic device, it is a good practice to make both the Power (+) and Ground (-) connections directly to the Battery and avoid connecting the power from the charging side of existing wiring or making use of existing "ACC" or other peripheral connection points. Make sure that wire of sufficient gauge and insulator type is used when connecting the outputs of the receiver to the control panel. Observe any component manufacturer's instructions and recommendations for proper integration of their product. This includes the power ratings and requirements of such components as relays, valves, solenoids, etc. Be sure to test each of the outputs with a multi-meter prior to connecting the outputs to your end devices. This will ensure that each output has been programmed to operate in the manner required by each end device. Filtering and Noise Suppression Whenever a solenoid or electromagnetic switch is controlled by the receiver, it is a good practice to install a Diode across its terminals to ensure that surges and spikes do not continue back into the circuit. Appropriate 36V Bi-directional Diodes kits can be ordered under the OMNEX part number AKIT Power the Transmitter 1. Install the batteries in the transmitter Batteries are installed in the transmitter by removing the battery cover using a slotted screwdriver and inserting 4 C alkaline batteries. Orientation of the batteries is embossed inside the battery housing. No batteries are required when the transmitter is connected to the receiver by a Pendant cable. NOTE: For operation at temperatures below 10 C lithium batteries are recommended. Low temperatures reduce battery performance for both alkaline and lithium types. Refer to the battery manufacturer s specifications for detailed information on low temperature performance. 2. Turn on the transmitter Transmitter Battery Housing Ensure all transmitter switches and paddles are in the neutral position. Turn on the transmitter by, pressing and releasing the [Power] switch The RED (E-Stop) light will flash quickly. Release the [E-Stop], the yellow (Active) light on the transmitter will begin to flash. WARNING: do not install batteries backwards, charge, put in fire, or mix with other battery types. May explode or leak causing injury. Replace all batteries at the same time as a complete set and do not mix and match battery types. A. Press the [E Stop] B. Press and release [Power] switch C. Turn CW & Release [E-Stop] Legend Solid Slow Fast 6 Red Green Yellow Alternating Red & Green

7 Test the Transmitter / Receiver Link Follow these steps to ensure that there is a Radio Link between the transmitter and receiver Refer to the Legend below for diagram details 1. Press [E-Stop] 2. Power the R160 The (E Stop) light and the (Link) light will come on RED (provided the transmitter is off), and the (Status) light will come on GREEN. 3. Power the T300 If the (Active) light on the transmitter is flashing and the (Link) light on the receiver is flashing GREEN, a link between the two exists. NOTE: The transmitter will shut itself off (and the receiver will then shut off all outputs) after 4 hours of inactivity as a battery saving feature. To restart the timer before the transmitter shuts off automatically, momentarily operate any toggle switch or paddle. The ORIGA System is now ready for use. If the receiver's (Link) light does not become GREEN follow the steps under Download ID Code first then Refer to Troubleshooting guide for more information. Download ID Code (Use in case of Link Test failure) Follow these steps to download the transmitter s unique ID Code into the receiver. This will allow the receiver to establish a Radio link with a specific transmitter. Refer to Troubleshooting Chart #4 for Tips and Considerations NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver. NOTE: If the transmitter is connected to the receiver with a Tether Cable, completing only steps 4 and 6 is necessary (it is not necessary to open the R160 case and press the Setup button). 1. Opening the R160 Case The cap is held on by two plastic tabs at opposing sides, which can be unlatched as shown using a screwdriver. Once the cap is free, the R160 can slide open. Use a small slotted screwdriver to press the Side Tabs inward. NOTE: When replacing the receiver cover, ensure the cover snaps completely into place to create a weather proof seal around the base of the receiver. 2. Prepare T300 A. Press [E-Stop] B. Twist CW & release [E-Stop] A. B. Legend Solid Slow Fast 7 Red Green Yellow Alternating Red & Green

8 Download ID Code (Use in case of Link Test failure) 3. Power R160 A. Supply power to the receiver. The (E-Stop) light and the (Link) light will come on RED and the (Status) light will come on GREEN A. NOTE: For this document, orientation of the paddle and switch operation will be defined as follows: Paddle UP is towards the switches Paddle DOWN is away from switches Switch UP is away from paddles Switch DOWN is towards the paddles. UP DOWN 4. Power T300 into Configuration Mode A. Hold [Power] switch UP B. Press [E-Stop] C. Twist CW & release [E-Stop] D. Release [Power] Switch A. C. B. D Put R160 into Setup Mode A. Press & hold [Setup] button until (Status) light goes from slow flash to fast flash B. Release [Setup] button. (Status) light goes to solid GREEN, (Link) light turns off A. Setup Button B. Setup Button NOTE: If left idle in Setup Mode for over 30 seconds, the receiver will time out. The (Link) light and (Status) light will flash RED rapidly. To return to Setup Mode, repeat step Download ID Code NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area. A. Press [Power] switch UP and release A. B. B. (Link) light goes to GREEN. Once complete, (Link) light goes to RED as the trans- Legend Solid Slow Fast 8 Red Green Yellow Alternating Red & Green

9 Calibrating Proportional Controls The transmitter s Paddles control the receiver s proportional output. The Paddles/Joysticks are used in conjunction with any of the transmitter s switches. The proportional output can be activated when a switch is held UP or DOWN; it will become active at an increasingly high level as the Paddle/Joystick is pushed/pulled. The minimum and maximum levels of the proportional output can be calibrated by following these steps. Refer to the Legend below for diagram details. NOTE: Calibration settings can be reset to factory default in steps 3 & 4 by holding the [Power] switch UP or DOWN for 5 seconds. 1. Power T300, Power R160 A. B. A. Refer to steps in Power the Transmitter B. Supply power to the R Setup T300 into Configuration Mode A. Hold [Power] switch DOWN for 5 seconds until the (Battery) LED goes to alternating RED and YELLOW. A. B. B. Release [Power] switch 3. Set Minimum Level A. Push the paddle (function) in the direction you wish to calibrate until the (Active) LED comes on B. Hold paddle and Press [Power] switch UP to decrease minimum level or DOWN to increase it A. B. 4. Set Maximum Level A. Fully push the paddle (function) in the direction you wish to calibrate until the (E-Stop) LED comes on. B. Hold paddle and Press [Power] switch UP to decrease maximum level or DOWN to increase it A. B. Note: Repeat steps 3 and 4 for each paddle (function) that needs to be calibrated. 5. Power Off A. Press [E-Stop] A. Legend Solid Slow Fast 9 Red Green Yellow Alternating Red & Yellow

10 Diagnostics T300 Transmitter Tether connection detected Low battery. Unit will run approximately 20 hours after Battery light starts flashing. The transmitter is in Calibration mode Power switch is stuck in the UP position. The Active light remain on momentarily when a function is activated (i.e. a switch or paddle is triggered). This is normal operation. Normal Operation The transmitter is in Download Mode. Normal Operation The Active light will flash 2 times per second, indicating that the transmitter is sending signals to the receiver. Stuck switch detected. Ensure that all switches are in a centered position. The transmitter will not power up when a function is ON. On Power Up Release the E-Stop button within 10 seconds to power up the transmitter, or the unit will power down. On Power Up Press and release the E-Stop button within 10 seconds to power up the transmitter, or the unit will power down. Diagnostics - D160 Expansion Module Indicator lights for the D160 Expansion Module FA STA FUNCTION/ Status Indicator Module is operating properly with a function on Low battery condition detected (refer to R160 diagnostic page for possible solution) Module is operating properly with a function off Fuse blown (refer to R160 diagnostic page for possible solution) Module has an unrecoverable fault, return for service There is a short to ground/over current (refer to R160 diagnostic page for possible solution) The module is powered incorrectly (refer to R160 diagnostic page for possible solution) There is a short to supply (refer to R160 diagnostic page for possible solution) Legend Solid Slow Fast 10 Red Green Yellow Alternating Red & Yellow

11 Diagnostics - R160 Receiver Normal Operation Transmitter is OFF If the transmitter is off, the receiver is operating properly. Transmitter is ON When the transmitter is turned on, the Link light (fast flashing) and E-Stop (GREEN) indicates the receiver is operating properly Transmitter is in Operation When a function is activated on the transmitter, the Fault light will turn on GREEN. This indicates the receiver is operating properly Transmitter is OFF When a latched function is activated then the transmitter is turned off, the Fault light will stay on GREEN. If the system was intentionally designed this way, the receiver is operating properly, if not call for service. Trouble Indicators Note: In some cases, the indicator lights will be different depending on whether the transmitter is on or off. Please note the transmitter status in the Description column for each case. Indicator s Description Solution Transmitter is ON The reason is the transmitter is not communicating with the receiver. Transmitter is ON A low battery condition has been detected. Transmitter is ON An internal fault with the E-Stop has been detected. Transmitter is ON A short to ground or excessive current draw on an output. It is most likely caused by a wiring fault. Transmitter is ON The E-Stop output has been connected with one of the other outputs Transmitter is OFF A wiring short to the battery has been detected. Transmitter is OFF The receiver has detected an internal fault. Transmitter is OFF Blown fuse detected. Transmitter is ON A setup failure has occurred. Transmitter is OFF The receiver is powered incorrectly. Refer to Troubleshooting Chart #3 for solutions To detect intermittent conditions caused by poor or corroded ground or power circuits, the GREEN light will continue to flash for 30 seconds after the condition has been removed. Inspect E-Stop wiring for short circuit. Disconnect E-Stop wire as close to the receiver output as possible. If the Status light changes to: GREEN, a short occurs after disconnection point. Stays flashing RED, send it in for service. Ensure transmitter is functioning properly, check status of each output connection: Press each function button and observe Fault. If GREEN, everything is OK. If RED, there is a short in that connection. Follow the wire and check for connections with other wires, disconnect to see if condition clears. If not, call for service. Refer to Troubleshooting Chart #1 for solutions Refer to Troubleshooting Chart #1 for solutions Refer to Page 6 for instructions on how to open the receiver case to access fuse. Check wiring for shorts or bare spots. If fuses continue to blow, call for service. Either hold the Setup button for 5 seconds to return to Setup mode or cycle power to return to the normal operating mode. Most likely cause of this condition is that an output wire or the E-Stop wire has been connected to the power supply while the power wire is disconnected from the power supply. Legend Solid Slow Fast 11 Red Green Yellow Alternating Red & Green

12 Troubleshooting Guide Chart #1 Test the Receiver R160 Start Initial Condition: Turn transmitter off (all lights are off press the E-Stop button) Cycle power to receiver (turn off and back on) Problem state: Status RED What is the state of the lights on the receiver? OK state: Status GREEN Link RED E-Stop RED Fault OFF Note: If there is a short to ground on an output, it is not indicated at this stage. To test for short to ground, refer to the *Fault is RED* procedure at the bottom of this page and follow the instructions. Problem state: Status flashing GREEN & RED The system is wired incorrectly. Most likely cause is one of the input/output wires has been connected to the power source. Go to Chart 2 Is the Status light flashing RED? YES Fuse is blown, change fuse 1. Inspect wiring looking for short circuits (e.g. bare wires) 2. If problem re-occurs, call for service. NO What is the state of the E- Stop light? Problem state: E-Stop ing RED Inspect E-Stop wiring looking for short circuits (e.g. bare wires) Disconnect the E-Stop output as close to the receiver output as possible. If the Status light changes to: GREEN, there is a short is the wiring after the disconnection point. Stays flashing RED, call for service. OK state: E-Stop RED Fault is OFF Call for service. What is the state of the Fault light? Fault is ing RED There is a short to supply. 1. Disconnect A & B connectors from receiver and check all outputs for power (e.g. bare wires, improper connections) make the correct adjustments 2. Call for service. *Fault is RED* There is a short to ground. Note: This should only occur when the transmitter is on and a function button is pressed. In this case the Status light will be GREEN and will turn RED at the same time as the Fault light. Go to Chart 2 to test the transmitter. If the transmitter is functioning properly, proceed to check the status of each of the output connections: Press each of the function buttons and observe the Fault. If the light turn GREEN, everything is OK. If the turns RED, there is a short in that connection. 12

13 Troubleshooting Guide (con t) Chart #2 Test the Transmitter T300 Turn off the receiver Ensure there are good batteries in the transmitter Turn on the transmitter What is the state of the lights? OK state: Active light steady for about 3 seconds then goes to fast flash. Battery light OFF E-Stop light OFF Toggle a switch, paddle or joystick Go to Chart 3 YES Does the Active light go to solid YELLOW? No light comes on at any time Both the Active light and the E-Stop light flash at the same time Complete the following steps in order: 1. Check battery orientation 2. Clean battery contacts 3. Check or Replace batteries 4. Call for service Stuck switch/paddle: 1. Return all paddles/switches to neutral (OFF) position 2. Toggle the switch/paddle a few times 3. Call for service NO Either the switch/paddle is defective or the switch/paddle connection to the circuit board is broken. Call for service Both the Active light and the Battery light flash at the same time Power switch is stuck in UP position: 1. Return switch to neutral position 2. Toggle the switch a few times 3. Call for service Active light and Battery light flashing alternately Low Battery Change Batteries Note: Low batteries will last approximately 20 hours once the Low Battery light begins to flash. Replace batteries by next shift. Battery light alternates between RED and GREEN. The transmitter is in Calibration mode 1. Turn unit OFF, then turn back ON 2. If condition persists, call for service. Battery light flashes for 10 seconds then all lights are OFF Press and release E-Stop if the condition persists, then either there is a faulty E- Stop or transmitter failure call for service 13

14 Troubleshooting Guide (con t) Chart #3 Testing the Transmitter / Receiver Communication Transmitter: Active light is flashing Receiver: Status GREEN Link RED Fault OFF E-Stop RED What is the status of the lights of both the transmitter and receiver? Transmitter: Active light is flashing Receiver: Status GREEN Link ing GREEN Fault OFF E-Stop GREEN There is no link between the transmitter and receiver Transmitter and receiver should be working properly. The problem may rest with the machine instead of the radio system Call for service Do you have a matched set? (i.e. the transmitter and receiver should have identical ID codes YES Call for service. NO Was the transmitter accidentally swapped with another one on the job site? POSSIBLY Search the job site for the correct transmitter. NO NO Was it found? YES Turn on the transmitter to check if the units function correctly. If not, proceed to Chart 1 The transmitter code may need to be re-downloaded to the receiver!!caution!! Note: Before you proceed with the Download ID procedure located on Page 7 & 8, great care and caution must be adhered to. Also, refer to Chart #4 for Tips and Considerations. If by accident, the transmitters have been switched with another unit, by downloading the ID code to a new receiver, it is possible for the transmitter to operate 2 units at the same time (if the original receiver unit is still on the job site). Therefore it must be certain that the transmitter / receiver pair are the correct set. Secondly, once the download procedure is completed, ensure all other units on the job site are stopped. Test the operation of the newly configured set to ensure no other machines on the site work with the same transmitter. Once you are certain that the transmitter / receiver pair are a unique set, continue normal operations. 14

15 Troubleshooting Guide (con t) Chart #4 Considerations when Downloading the ID Potential downloading issues If testing of the receiver and transmitter both show the system as working (Chart 1 & 2), then the transmitter and receiver will both go into Download/Configuration mode. Possible issues could arise during Step 4, the download phase of reprogramming. In this case there are 2 symptoms to look for: 1. The Link light on the receiver will not turn GREEN when the power switch is toggled on the transmitter to download 2. The receiver will time out indicating that it didn t receive a signal from the transmitter within the 30 seconds from the time the receiver was put into Setup Mode. If all indications appear normal during the download phase, test the link by turning on the transmitter (note: the transmitter shuts off after transmitting the ID code in Step 4) 1. If the Link light on the receiver doesn t turn GREEN, the receiver didn t receive all of the information that was sent from the transmitter. Possible Solutions 1. Try the Downloading steps again 2. If this doesn t correct the problem, send both the transmitter and receiver in for service. Note: you could try to determine whether the fault lies with the transmitter or receiver by completing the downloading procedure with a different transmitter. If this step works, then the fault lies with the original transmitter. If not, the fault may lie with the receiver.!!caution!! Note: Before attempting downloading with another transmitter, understand that reprogramming the receiver with another transmitter, could result in two receivers on the job site responding to the one transmitter. If the original transmitter was sent in for repair, Disconnect the receiver (disconnect connector A) to continue using the machine without remote capability and without fear of inadvertently operating the machine with the other transmitter. Connector A Reprogramming Tips: 1. Use a pointy instrument to depress the Setup button on the receiver (i.e. a pen) as the button is relatively small 2. Follow each step as laid out in the procedure 3. Never lay the receiver circuit board down on anything metallic (there are contact points on the back which could contact the metal and damage the receiver) 15

16 Parts & Accessories Part OMNEX Part Number Description Batteries B x C alkaline Fuse F V Bi-directional, Bussman ATC-15 Shoulder Strap FMEC T300 Tear-away shoulder strap Output Cable ACAB R160 Output Cable, Generic ACAB R160 Output Cable, Generic, Tethered ACAB Tether Cable, 10m Pendant Cable ACAB Tether Cable, 8m ACAB Tether Cable, 4-12ft Connector Kit AKIT Includes Deutsch socket connectors, wedges, pins and sealing plugs Bipolar Diode Kit AKIT Motorola P6KE36CA Shoulder Strap Pendant Cable Pendant Coil R160 Output Cable Specifications Size D160 Module R160 Receiver T300 Transmitter 5.1 x 4.7 x x 4.7 x " x 6.0" x 5.0" (130mm x 119mm x 36mm) (130mm x 119mm x 36mm) (240mm x 152mm x 127mm) Weight 0.65lbs (0.295kg) 0.65lbs (0.295kg) 3.5 lbs (incl. batteries) (1.2kg) Construction High impact plastic, weatherproof High impact plastic, weatherproof 16 High impact, low temperature plastic, weatherproof Input Power +9V to 30VDC +9V to 30VDC 4C alkaline batteries Battery Life N/A N/A 500 hours (continuous use) Operating Temperature Range Outputs -40F to 158F (-40C to 70C) -40F to 158F (-40C to 70C) -40F to 140F (-40C to 60C) 3A (max) each (sourcing), 15A (max) each (combined) 3A (max) each (sourcing), 10A (max) each (combined) Antenna N/A Internal Internal Approvals FCC Rules and Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part ISC RSS 210 Issue 6, Sept USA- FCC part Canada- ISC RSS 210 Issue 6, Sept. Europe- EN 440 Australia- C-Tick Warranty OMNEX Control Systems ULC warrants to the original purchaser that the OM- NEX products are free from defects in materials and workmanship under normal use and service for a period of ONE YEAR, parts (EXCLUDING: SWITCHES, CRYSTALS, OR PARTS SUBJECT TO UNAUTHORIZED REPAIR OR MODIFI- CATION) and labor from the date of delivery as evidenced by a copy of the receipt. OMNEX's entire liability and your exclusive remedy shall be, at OM- NEX's option, either the (a) repair or (b) replacement of the OMNEX product which is returned within the warranty period to OMNEX freight collect by the OMNEX APPROVED carrier with a copy of the purchase receipt and with the return authorization of OMNEX. If failure has resulted from accident, abuse or misapplication, OMNEX shall have no responsibility to repair or replace the product under warranty. In no event shall OMNEX be responsible for incidental or consequential damage caused by defects in its products, whether such damage occurs or is discovered before or after replacement or repair and whether or not such damage is caused by the negligence of OMNEX Control Systems ULC. N/A OMNEX Control Systems ULC Coast Meridian Road Port Coquitlam, BC, Canada V3C 6G5 Tel: Fax: Toll Free: