for ECM Titanium) This guide contains a complete explanation of the Driver Maker plug-in, an add-on developed for
|
|
- Brooke Hall
- 7 years ago
- Views:
Transcription
1 Driver Maker User Guide (Plug-in for ECM Titanium) Introduction This guide contains a complete explanation of the Driver Maker plug-in, an add-on developed for ECM Titanium, the chip-tuning software produced by Alientech S.r.l.. Driver Maker is not included in the basic version of ECM Titanium, but can be purchased separately. This manual contains all the information you need to make the best use the plug-in, and to simplify the description of its functions, the sections of this guide often contain pictures. If the pictures belong to a previous version of the software, please contact your dealer to find out whether a newer version of the guide is available. In the explanation of the sections there are references to ECM Titanium software. If you have questions about the operation of this software, you should first read the Quick User Guide located in ECM Titanium USB flash drive (USB Picodisk). The Driver Maker add-on, like ECM Titanium software, is designed for computers running Windows Vista or 7. 1
2 Table of contents Introduction... 1 Section 1 What the Driver Maker plug-in is... 4 Alientech Drivers... 5 Custom Drivers... 5 Section 2 How to run the Driver Maker plug-in... 6 Opening Driver Maker from ECM Titanium main window... 6 Opening Driver Maker from the 2D Graphics window of ECM Titanium... 7 Section 3 Features... 9 Driver Maker Main Window... 9 EPROM data D Graphic Area Address Scrollbar DRIVER data Display MOD Selection Menu Driver Graphics Help Supported views Entering new map names Editor Search window Section 4 How to develop a new Driver Adding a single map Adding a map with its similars Adding a similar map to a map previously entered
3 Section 5 How to associate a Checksum family Section 6 How to save a custom Driver Section 7 How to load an original stock file with a User Driver
4 Section 1 What the Driver Maker plug-in is Driver Maker is an add-on for ECM Titanium software developed by Alientech S.r.l., used to develop and edit Driver files used by the main software. Drivers are support files containing the position of maps for engine control, stored in an original stock file that is read from the vehicle s electronic control unit. Loading an original stock file with ECM Titanium and its Driver,, it is possible to see the list of the available maps (Picture 1). Picture 1: Available maps panel. Using a Driver it is possible to edit an original file using all four data views of the main software, ECM Titanium, which are: Map 3D Graphics 4
5 2D Graphics Hexadecimal There are two types of Drivers: Alientech Official Drivers: developed by Alientech, they can be downloaded from the Internet Data Bank. Custom Drivers: developed by the user using Driver Maker or Driver Manager Plus (an obsolete plug-in for ECM Titanium). Alientech Drivers They are provided only to Alientech S.r.l customers who have subscribed a contract with the company or its authorized reseller, and can be downloaded from the Internet Data Bank. Once downloaded, Drivers are stored in ECM Titanium USB Flash drive. At the end of the subscription it is no longer possible to download or request new Drivers from the Internet Data Bank service. ECM Titanium software will continue to operate normally anyway Alientech official Drivers already contain all the maps and parameters that are usually increased in order to achieve a good modified file. Custom Drivers They are developed by ECM Titanium users using plug-in softwares, Driver Maker or Driver Manager Plus (an obsolete plug-in)only be used from the USB Flash drive that has generated them. It is therefore not possible to use a Their structure is identical to that of official Drivers, but can custom Driver developed by another ECM Titanium Flash drive. Custom Drivers are useful for adding custom maps to the official ones (e.g. for special tunings), or develop new Drivers for original files not supported by reading tools. It is possible to modify an Alientech official Driver with Driver Maker, but it is necessary that this Driver has been previously downloaded from the Internet Data Bank and that the original stock file associated is loaded into the main software, ECM Titanium. To develop a new Custom Driver without inheriting any information, the only condition is to load only the original stock file in ECM Titanium software. 5
6 Section 2 How to run the Driver Maker plug-in When buying the Driver Maker plug-in, it is provided or ed the activation file DriverMaker.plt,, which must be copied to the path X:\ECM_Titanium\PlugIn (where x is the name given to the USB Picodisk Flash drive by your operating system). This file cannot be transferred to third parties, since it is compatible only with the ECM Titanium Flash drive for which it was generated. To run the Driver Maker plug-in, ECM Titanium software must be already open and an original stock file must have been loaded. When using the plug-in for the first time, it is recommended verifying that the activation file is present on the memory of the USB Flash drive. Opening Driver Maker from ECM Titanium main window To run Driver Maker from ECM Titanium main window there are three possibilities: Click on the icon (top left). In the Instruments menu, select Custom drivers (Picture 2). Picture 2: Instruments menu, Custom drivers option. Use the key combination [Alt+D]. 6
7 Opening Driver Maker from the 2D Graphics window of ECM Titanium To run Driver Maker from 2D Graphics window there are three possibilities: Click on the icon (top left). In the Instruments menu, select Custom drivers (Picture 3). Picture 3: Instruments menu, Custom drivers option. Use the key combination [Alt+D]. If the original stock file was not associated with a Driver, the window opened is the one in the Picture 4. 7
8 Picture 4: Driver Maker main window (no Driver associated to the original file). If the original file was associated with a Driver, the window opened is the one in Picture 5. Picture 5: Driver Maker main window (Driver associated to the original file). 8
9 Section 3 Features This section explains all the features of Driver Maker plug-in that can be used to enter maps and other information in a custom Driver. Driver Maker Main Window In the main window of the plug-ispecific (Picture 6) there are several panels and panes, each one with a function. EPROM data Picture 6: Driver Maker main window. Picture 7: EPROM data panel. The EPROM data panel (Picture 7) contains all the details of the original and modified files that were loaded with ECM Titanium.. If no modified file has been loaded yet, in the MOD line there is a copy of the original file. The top line (ORI) contains the data of the original file and the bottom line (MOD) those of the modified file. 9
10 The details displayed in the EPROM data panel are: ORI: Path to the folder where the original file is saved. MOD: Path to the folder where the modified file is saved. Address: Hexadecimal address pointed by the cursor located in the 2D Graphic Area. Dec: Conversion to decimal of the data in the hexadecimal address pointed. Conversion depends on the binary format selected in the Display panel. Hex: Hexadecimal view of the data in the hexadecimal address pointed. Conversion depends on the binary format selected in the Display panel. Difference: Difference expressed in absolute value (first line) and in percentage (second line) between the pointed decimal values of the original and modified file. 2D Graphic Area Picture 8: 2D Graphic Area. The 2D Graphic Area panel (Picture 8) shows the traces of the original and modified file overlapping each other. Traces are formed by a sequence of points, whose height depend on the values found in their respective hexadecimal addresses. es. The vertical axes that are located at the left and right of the 2D Graphic Area are used as "rulers", to help realize the height of the points and therefore of the traces. The horizontal axis of the 2D Graphic Area is formed by the hexadecimal addresses of the original and modified file, increasing from left to right (000000h = beginning of the file). 10
11 You can select a portion of a trace by double-clicking with the right mouse button on two addresses (once for the beginning and once for the end of the map). Address Scrollbar Picture 9: Address Scrollbar. The Address Scrollbar (Picture 9) contains all useful buttons to scroll the traces of the original and modified file, therefore move along the horizontal axis of the 2D Graphic Area. The buttons you can find in the Address Scrollbar are: : To go to the Beginning address or the End address. : To scroll Back and Forward. : To scroll Back and Forward for differences between the original and modified file. : If a multiple selection of the trace has been made, the Previous selection and Next selection buttons move the 2D Graphic Area between the several sections. : To lock the trace of the original file and scroll only the one of the modified file. : To lock the trace of the modified file and scroll only the one of the original file. : To go to the Previous Map or Next Map,, respectively of the Driver loaded (top line) and the one you are creating (bottom line). Offset: To display the difference between the address of the original file and the modified file, that is, the misalignment between the two traces. : The first field is used to write a hexadecimal address where to move the 2D Graphic Area, and the Go button to execute the move. : To align the traces at the same address (Align ORI). : To open the Search window. 11
12 DRIVER data Picture 10: DRIVER data panel. The Driver Data panel (Picture ECM Titanium: 10) contains the details of the Driver that has been loaded with File Name: contains name and path of the Driver file associated. Checksum: contains the number of the formula associated with the loaded Driver. If no Driver has been loaded with ECM Titanium and you proceed to develop a new one, the default File Name is USER, and it can be changed when saving the new Driver. The Checksum field is used to associate a checksum correction formula with a Driver developed using Driver Maker plug-in. If you are developing a new Driver and do not know which correct formula to associate, it is recommended to start from an Alientech official Driver. Display Picture 11: Display panel. The Display panel (Picture 11) contains all numeric formats supported and the display settings available for the 2D Graphic Area. 12
13 The numeric formats supported by Driver Maker are listed in the table in Picture 12, which also shows minimum and maximum decimal values for each format. Numeric Format 8 bit (unsigned ) 8 bit (signed ) IEEE MOTOROLA Min Max Min Max bit (unsigned ) bit (signed ) bit (unsigned ) 0 4x x bit (signed ) -2x10 9 2x10 9-2x10 9 2x10 9 Floating Point it depends on the precision it depends on the precision it depends on the precision it depends on the precision Picture 12: supported Numeric formats. Available display settings are: IEEE/MOTOROLA: The selection depends on the writing encoding of the microcontroller on the ECU board. +/-: The selection allows switching from the unsigned scale to the signed, combined with one of the four numeric views (8 bit, 16 bit, 32 bit, Floating point). Data Alignment: To align the 2D Graphic Area to an odd address that would not be accessible with 16 bit, 32 bit, and Floating point views. It has to be used only for views greater than 8 bits. Info Driver: If a Driver has been associated with the original stock file loaded with ECM Titanium,, numeric format and display settings for the 2D Graphic Area are taken from the Driver. Use last map: Numeric format and display settings for the 2D Graphic Area are taken from the last map included in the Driver. 13
14 Zoom H: The cursor is used to increase or decrease the horizontal zoom of the 2D Graphic Area. With the horizontal zoom to maximum (cursor all the way to the right) it is possible to display 256 consecutive hexadecimal addresses. Increasing the box x1, it is possible to display multiples of 256 addresses at a time in the 2D Graphic Area (default 256 x1). Zoom V: The cursor is used to increase or decrease the vertical zoom of the 2D Graphic Area. MOD Selection Picture 13: MOD Selection panel. The Mod Selection panel (Picture 13) contains the details of the single or multiple selection made with the mouse (right button) on the trace of the file loaded as modified in the 2D Graphic Area. The details you can find in the Mod Selection panel are: From: It is the first hexadecimal address of the selection made on the trace of the modified file. In Picture 12, the first address is h. To: It is the last hexadecimal address of the selection made on the trace of the modified file. In Picture 13, the last address is h. size: It is the number of points (expressed in decimal) included in the selection; from the first address to the last (from h to h). In Picture 13, the selection is 153 points long. Number/Number: It represents the number of the selection pointed by the cursor at the time being, compared to the total number of selections made in the 2D Graphic Area. In Picture 13, 1/1 is the first map of a selection that includes only one map (single selection). Clear selection: To remove the single or multiple selection made in the 2D Graphic Area. To remove singularly only one of the selections made in the 2D Graphic Area, just click with the right mouse button on the first address of the desired selection. 14
15 Menu Driver Maker main window has a menu that contains the most important functions included in the plug-in. Driver Picture 14: Driver menu. The Driver menu (Picture 14) contains the following functions and their shortcuts to recall them: Save: To save the Driver just created associated with the file loaded as modified. New: To create a new Driver associated with the file loaded as modified. Current: To copy the information of the Driver associated with the original stock file previously loaded with ECM Titanium and paste it in the new Driver that you want to create for the file loaded as modified. Map List [Ctrl+W]: To switch between the Driver Maker plug-in window that displays the 2D Graphic Area to the one that displays the Map data view. Show editor [Ctrl+E]: To open the Editor panel at the bottom of the open window. New map code [Ctrl+N]:: To add a new name to the list of default map names for later use with the Driver Maker plug-in. Previous similar map [Page Up]: To move the view of the 2D Graphic Area to the previous map, in the event that the Driver has similar maps. Next similar map [Page Down]: To move the view of the 2D Graphic Area to the next map, in the event that the Driver has similar maps. 15
16 Graphics Picture 15: Graphics menu. The Graphics menu (Picture 15) contains the following functions and their shortcuts to recall them: Scroll back [Left]: To scroll back (leftwards) the traces displayed in the 2D Graphic Area. Scroll forward [Right]: To scroll forward (rightwards) the traces displayed in the 2D Graphic Area. Scroll back (fast) [Shift+Left]: To fast scroll back (leftwards) the traces displayed in the 2D Graphic Area. Scroll forward (fast) [Shift+Right]: To fast scroll forward (rightwards) the traces displayed in the 2D Graphic Area. Scroll up [Shift+up]: To scroll upwards the traces displayed in the 2D Graphic Area. Scroll down [Shift+down]: To scroll downwards the traces displayed in the 2D Graphic Area. Zoom H (enlarge) [Ctrl+Left]: To zoom in horizontally the 2D Graphic Area that displays the traces (horizontal zoom magnification). Zoom H (reduce) [Ctrl+Right]: To zoom out horizontally the 2D Graphic Area that displays the traces (horizontal zoom minimization). 16
17 Zoom V (enlarge) [Ctrl+Up]: To zoom in vertically the 2D Graphic Area that displays the traces (vertical zoom magnification). Zoom V (reduce) [Ctrl+Down]: To zoom out vertically the 2D Graphic Area that displays the traces (vertical zoom minimization). Lock cursor [Ctrl+S]: To lock the cursor in an arbitrary point of the 2D Graphic Area. To unlock, simply repeat the same selection. Move ORI maps up [Ctrl+R]: To move upwards the horizontal segment indicating a map on the Driver of the file loaded as original. Move ORI maps down [Ctrl+F]: To move downwards the horizontal segment indicating a map on the Driver of the file loaded as original. Move MOD maps up [Ctrl+T]: To move upwards the horizontal segment indicating a map on the Driver of the file loaded as modified. Move MOD maps down [Ctrl+G]: To move downwards the horizontal segment indicating a map on the Driver of the file loaded as modified. Help Picture 16: Help window. The Help item opens a window (Picture 16), which contains the list of basic actions that can be performed with Driver Maker,, and alongside each one, an explanation of the result obtained. 17
18 If you are developing a Driver for a file belonging to a BOSCH ECU type EDC15, EDC16 or EDC17, Driver Maker includes already the data structure of these ECUs (Choose break ENCODING), and you can quickly add their maps and corresponding axes. The lower part of the Help window presents a rational function which includes four parameters: P1, P2, P3 and P4. The parameters are often used by advanced users to apply the same conversion formulas used by engine control unit manufacturers. Conversion formulas are already included in Alientech official Drivers with advanced structure. Standard structure Drivers,, instead, does not include conversion formulas, so the numbers displayed are simply the conversion to decimal of values belonging to each hexadecimal address of each map. Supported views The views supported by Driver Maker are two: 2D Graphics window (Picture 17). Map window (Picture 18). Picture 17: 2D Graphics window. 18
19 Picture 18: Map window. 2D Graphics window allows you to scroll the traces of loaded files (original and modified) with the Address Scrollbar, zoom horizontally or vertically, and choose in the Display panel the correct number format for each map met. By using the mouse buttons and basic actions listed in the Help window, it is possible to select the maps belonging to the trace of the modified file and then enter them using the Editor panel. Map window allows you to display the list of maps in the Driver, sorted by category and under its own name, and immediately observe values and reference axes of each map. By activating the Editor panel (Picture 19), it is possible to see the conversion parameters of the selected map (P1, P2, P3 and P4) and axes (P1 and P2). Picture 19: Editor panel. 19
20 Picture 20 shows the Map List panel of the Alientech official Driver A342_951. Picture 20: Map list panel. To view a map in the Map Area just click on the name of the desired map. To switch between 2D Graphics window and Map window (and vice versa): In the Driver menu, select Map list (Picture 14). Use the key combination: [Ctrl+W]. 20
21 Entering new map names With Driver Maker,, it is possible to create custom names for maps to be included in a new Driver. To enter a custom name, use the Create a new map code window. To open the Create a new map code window from the 2D Graphics or Map window: In the menu, click Driver and select New map code (Picture 14). Use the key combination: [Ctrl+N]. If the Editor panel is open, click the New button (left). Picture 21: Create a new map code window. After opening the Create a new map code window (Picture 21), to create a new name: In the Category drop-down down list, select the category where the new map name must be in. In the Description field, enter the desired name. Click on Create code once it is enabled. Group 1: Standard structure Driver INJECTION SPARK ADVANCE TURBO LIMITERS Group 2: Advanced structure Driver Air Control Engine Torque Injection System Rail Turbo System Limiters Spark Advance Volumetric System Breaks Picture 22: Map Categories available according to the Driver structure. 21
22 The categories available for the maps depend on the internal structure of the Driver (Picture 22). The added name will be then available for all new Drivers that will be developed with Driver Maker. When you open the Driver Maker plug-in with ECM Titanium, but you do not want to start from the maps contained in an Alientech official Driver, a dialog window is opened that lets you choose which Group of map categories you want to use (Picture 23) Editor Picture 23: Choose a group of map categories. Picture 24: Editor panel. The Editor panel (Picture 24) allows browsing the conversion parameters of a selected map and its reference axes or, if adding a new map to the Driver, allows entering them. To activate the Editor panel at the bottom of the 2D Graphics window or the Map window: In the menu, click Driver and select Show Editor (Picture 14). Use the key combination: [Ctrl+E]. 22
23 The conversion parameters and details of the selected map contained in the Editor panel are: Category: Category to which the selected map belongs (Picture 23). New: To open the Create a new map code window (Picture 21), and create a custom map name. Description: Name of the selected map. Address: Hexadecimal address where the map begins. map Number/Number: Number of the similar map currently displayed in the Map Area, compared to the total number of similar maps with the same name. In Picture 24, map 2/2 represents the second similar map of a total of two similar maps that have the same name. Encoding: Selection of a type of common data structure that some ECUs possess (Picture 16). The manual selection is associated to a generic data structure. Data Type: Numeric format associated with the data of the map. Signed: To apply the signed scale to the numeric format associated with the data of the map. Dec digits: Number of decimal digits after the decimal point that are displayed for each data of the map. Formula: Conversion formula applied to the data of the map. Unit of meas.: Unit of measurement associated with the data of the map. P1, P2, P3 and P4: The four parameters of the conversion rational formula associated with the data of the map (Picture 16). Minimum: Minimum value (converted with the selected Formula) that a data of the map can take on, through a modification made with ECM Titanium. Maximum: Maximum value (converted with the selected Formula) that a data of the map can take on, through a modification made with ECM Titanium. Increment: Minimum increment value (converted with the selected Formula) that can be applied to a data of the map, through a modification made with ECM Titanium. Rows: Number of rows forming the map. Address: Hexadecimal address where the vertical reference axis begins. Reverse: To swap the byte order of the data forming the vertical axis. Data Type: : Numeric format associated with the data of the vertical axis. Signed: To apply the signed scale to the numeric format associated with the data of the vertical axis. Dec digits: Number of decimal digits after the decimal point that are displayed for each data of the vertical axis. 23
24 Formula: Conversion formula applied to the data of the vertical axis. Rounding: To round off the data of the vertical axis, converted with the selected Formula. P1, P2: The two parameters of the conversion rational formula associated with the data of the vertical axis. Unit of meas.: Unit of measurement associated with the data of the vertical axis. Columns: Number of columns forming the map. Address: : Hexadecimal address where the horizontal reference axis begins. Reverse: : To swap the byte order of the data forming the horizontal axis. Data Type: : Numeric format associated with the data of the horizontal axis. Signed: To apply the signed scale to the numeric format associated with the data of the horizontal axis. Dec digits: Number of decimal digits after the decimal point that are displayed for each data of the horizontal axis. Formula: Conversion formula applied to the data of the horizontal axis. Rounding: : To round off the data of the horizontal axis, converted with the selected Formula. P1, P2: The two parameters of the conversion rational formula associated with the data of the horizontal axis. Unit of meas.: Unit of measurement associated with the data of the horizontal axis. Add: To add d the selected map to the list of the current Driver. Modify: To modify the selected map applying the parameters currently displayed. Erase: Erase the selected map from the map list of the current Driver. Similar to...: To add a map selected in the 2D Graphic Area as a similar map to one already included in the list of the current Driver. Copy from...: To copy the details of the conversion formulas from a map already included in the list of the current Driver. Split: To turn a selection made in the 2D Graphic Area into a series of selections formed by a single value (example: when selecting a range of 10 values, Split turns this range into a series of 10 consecutive selections formed by an interval of a single value). Save: To save the custom Driver just developed with Driver Maker in the user Driver list stored in ECM Titanium Database. Update: To update the map list of the Driver modified with Driver Maker, currently loaded in the ECM Titanium program memory. Exit: To exit Driver Maker plug-in and return to ECM Titanium program. 24
25 Search window The Driver Maker plug-in includes within a handy tool to search data, which allows you, among other things, to automatically find the maps that belong to a certain category of Bosch engine control units (EDC15, EDC16, EDC17). Picture 25: Search window. By pressing the button, the Search window is opened, which contains several criteria of analysis and selection to refine the test of data that belongs to the file loaded as original (ORI) or as modified (MOD). 25
26 Numeric values: By enabling the selection, it possible to search for the numeric value entered in the white box next to the from: item. Values in a range: By enabling the selection, also the second white box is activated and the search is performed between the minimum value contained in the box from: and the maximum in the box to:. Text String: By enabling the selection, the white box below is activated, where it is possible to enter the text to search (characters, letters and punctuation marks). Hex string: By enabling the selection, the white box below in activated, where it is possible to enter the hexadecimal data to search (two digits at a time, separated by a space). ASCII Blocks: To search for all possible sequences of characters, letters, and punctuation marks, starting from a minimum number selectable in the min box. The View the reversed Data option is useful for those files where the text has been entered reversed. Selected Block: To search for a section of file, previously selected in the 2D Graphic Area with the right mouse button, in the original or modified file. BOSCH EDC15-EDC16 maps: To search for Curves Type (2 dimensions) and Tables Type (3 dimensions) objects, starting from a minimum of 8 up to a maximum of 32 as Sizes. Data format: To choose the numeric format according to which the Numeric Values and values in a range searches are performed. Search in: To select the original (ORI) or modified (MOD) file as object of the search. Center the address: : To display each result on the list in the middle of the 2D Graphic Area. Always on foreground: To keep the Search window always visible in the foreground. >>: To expand or reduce the Search window. Start: To start the search, according to the parameters previously selected. Stop: To abort the ongoing search. Exit: To close the Search window. Search Result: The box contains the list of search results. Each result is displayed by Address and Description. 26
27 Section 4 How to develop a new Driver To develop a User Driver with Driver Maker plug-in, first it is necessary to load a file from the hard disk of your PC or from the Database with ECM Titanium, and then choose one of several ways to launch Driver Maker from the main window of the software: Click the icon (top left). In the Instruments menu, select Custom Drivers. Use the key combination: [Alt+D]. If the original file is associated with an Alientech official Driver,, the plug-in will display the following message (Picture 26) at the opening. Picture 26: Create a new map code message. By choosing Yes, it is possible to proceed with the addition of new maps to the Alientech official Driver, while by choosing No, it will be displayed the message in the next figure to choose the type of Driver. 27
28 Picture 27: Choose a group of map category message. Please note that when you choose to add new maps to an Alientech official Driver, it is not necessary to change the Checksum family associated, because it is already the right one. When you choose the option to create a new Driver, if the tool used to re-flash the modified file on the ECU does not automatically corrects the Checksum (for example, a memory chip programmer), you must make the Checksum correction with ECM Titanium and, therefore, you need to select the right Checksum algorithm in the DRIVER Data panel. Picture 28: DRIVER data panel. Adding a single map Entering a map in a new Driver or adding one in an Alientech ech official Driver are basically two identical operations. To correct procedure to perform both is: 1. Display the 2D Graphics window with Driver Maker. 2. In the 2D Graphic Area,, select the portion of trace that includes the map with the right mouse button. Once for the beginning and once for the end of the map (Picture 29). 28
29 Picture 29: 2D Graphic Area. 3. Display the Editor panel (Picture 30). 4. Fill in the information concerning Category and Description of the map. 5. Enter the right size of the selected map in the Rows and Columns fields. 6. Press the Add button and confirm the addition of a new map. Picture 30: Editor panel. If you know the conversion formulas of map data, you can use the Editor panel to enter the correct factors in the Formula fields (P1, P2, P3, P4), respectively for the Map, the Rows reference axis (vertical), and the Columns reference axis (horizontal). Unit of Meas. fields can be used to enter the unit of measurement of physical values that belong to the Map, the Rows reference axis (vertical), and the Columns reference axis (horizontal). Dec digits and Rounding fields are used to increase the accuracy of data displayed in Map format. Minimum, Maximum, and Increment fields are important in the development phase of the original file with ECM Titanium software, because they allow defining the smallest and largest value that can be entered in the map, in addition to the minimum increment that can be applied to a value which is part of the map. Adding a map with similar maps The procedure for entering a map with similar maps is very similar to the one described previously. Please note that a similar map is a map that has the same size, and a shape very similar (if not identical) compared to a map previously entered with Driver Maker. The correct procedure to enter a similar map is: 1. Display the 2D Graphics window with Driver Maker. 29
30 2. In the 2D Graphic Area,, select the portion of trace that includes the main map. All similar maps can be added with the right mouse button, by positioning the cursor at the beginning of each similar map, in order to create a multiple selection as in Picture 31. Picture 31: 2D Graphic Area. 7. Display the Editor panel (Picture 32). 8. Fill in the information concerning Category and Description of the map. 9. Enter the right size of the selected map in the Rows and Columns fields. 3. Press the Add button and confirm the addition of a new map. Picture 32: Editor panel. The map 2/2 fields in Picture 32 shows the input of two similar maps (main map and its similar). By pressing the Add button, in addition to the main map all the similar maps selected in the procedure are added to the list of the Driver. If all fields in the Editor panel have been filled, the same properties are applied also to the values of the similar maps. 30
31 Adding a similar map to a map previously entered Adding a similar map to a map already on the list of the Driver is very easy. 1. Display the 2D Graphics window with Driver Maker. 2. In the 2D Graphic Area,, select the portion of trace that belongs only to the similar map, as in Picture 33. If there is more than a similar map, add them all with the right mouse button, by positioning the cursor at the beginning of each similar map. Picture 33: 2D Graphic Area. 3. Display the Editor panel (Picture 34). 4. Press the Similar to button and choose in the list displayed the map to which associate the similar map previously selected in the 2D Graphic Area. Picture 34: Editor panel. 31
32 Section 5 How to associate a Checksum family Alientech official Drivers contain an indication of the Checksum algorithm to use to validate a file modified with ECM Titanium.. The correction formulas are called Checksum family, and are identified by a number; for example, in Picture 35 the number is 98. Picture 35: Available maps panel. If the tool used to re-flash the modified file on the ECU does not automatically corrects the Checksum (for example, a memory chip programmer), you must make the Checksum correction with ECM Titanium. Even custom Drivers must then contain the number that refers to the Checksum algorithm of ECM Titanium to apply the correction to the modified file. 32
33 Picture 36: DRIVER data panel. The DRIVER data panel (Picture 36) contains the details of the Driver that was loaded with ECM Titanium: File Name: Contains name and path of the Driver file associated. Checksum: Contains the number of the formula associated with the loaded Driver. To associate a Checksum algorithm, it is necessary to: Locate the DRIVER data panel. Select the number of the desired Checksum algorithm. When saving the custom Driver,, the Checksum correction family will be associated with the new support file. If no Driver was loaded with ECM Titanium and you want to develop a new one with Driver Maker,, the number referred to the Checksum algorithm can be changed when saving. In this case, if you do not know which correct formula to associate, it is recommended to start from an official Alientech Driver, or contact ct your dealer. 33
34 Section 6 How to save a custom Driver To save a custom Diver in the ECM Titanium Database, there are two options: In the Driver menu, select Save (Picture 37). In the Editor panel, click the Save button (Picture 38). Picture 37: Driver menu. Picture 38: Editor panel. Picture 39: Save Driver in the Database window. 34
35 The Save Driver in the Database window (Picture 39) is used to enter the Identification data of the new Driver, such as: Manufacturer: The vehicle manufacturer. Model: The specific model of the vehicle. Description: A short comment for the new Driver. After specifying Manufacturer and Model of the car which the original file belongs to, it is possible to click the Record button to permanently save the new Driver,, even without writing any description. It is always better to add, in the Description field, a short comment of the maps included in the custom Driver, to be able to easily distinguish it later, for example when you need to associate it with an original stock file loaded with ECM Titanium. After developing a new custom Driver and saving it in the Database of ECM Titanium software, it is possible to close the Driver Maker plug-in. 35
36 Section 7 How to load an original stock file with a User Driver To load an original stock file with a User Driver developed using Driver Maker plug-in, it is only necessary to use ECM Titanium software. To load a file associating it with a User Driver, it is necessary to: 1. Load a new file from the hard disk of your PC or from ECM Titanium Database. 2. Open the Search for a Driver in DB window (Open button next to Driver, in the main window of ECM Titanium). 3. Stop the search for a Driver with the Abort search button (in case it is carried out automatically). 4. Enable the Only personal Drivers selection. 5. Then select Manufacturer and Model for the vehicle to which the file loaded belongs in the Search criteria (optional) panel. 6. Press the Start search button. The search may include more than one result, if more than one User Drivers was made for the vehicle which Manufacturer and Model are entered as criteria for the search. To find the right User Driver, it is helpful to read the short comment that was entered in the Description panel, when you saved the Driver with the Driver Maker plug-in. Picture 40: Save Driver in the Database window. For this reason it is very important to add a short comment when saving a new custom Driver. 36
You can start almost every task you perform in QuickBooks by clicking something a
appendix c s You can start almost every task you perform in QuickBooks by clicking something a menu item, a button in a toolbar or icon bar, or a link in one of the Centers or the Company Snapshot. But
More informationMicrosoft Frontpage 2003 Keyboard Shortcuts
Work with and manage Web pages F8 CTRL+N CTRL+O CTRL+F4 CTRL+S CTRL+P F5 CTRL+ CTRL+Shift+ CTRL+Shift+B ALT+F4 CTRL+ Shift+8 CTRL+ / CTRL+F F3 Shift+F3 CTRL+F3 CTRL+Shift+F3 CTRL+H F7 Shift+F7 CTRL+Z or
More informationTrace600 OTDR Test Management Software User s guide
Trace600 OTDR Test Management Software User s guide T e s t & I n s p e c t i o n A Trace600 OTDR Test Management Software User s guide T e s t & I n s p e c t i o n 2002, AFL Telecommunications, all rights
More informationAccess 2013 Keyboard Shortcuts
Access 2013 Keyboard Shortcuts Access app shortcut keys Design-time shortcut keys These shortcut keys are available when you are customizing an app in Access. Many of the shortcuts listed under Desktop
More informationInternet Explorer 7. Getting Started The Internet Explorer Window. Tabs NEW! Working with the Tab Row. Microsoft QUICK Source
Microsoft QUICK Source Internet Explorer 7 Getting Started The Internet Explorer Window u v w x y { Using the Command Bar The Command Bar contains shortcut buttons for Internet Explorer tools. To expand
More informationUser Manual. DG LINK Application Program 071-0056-50. www.tektronix.com. This document applies to firmware version 2.00 and above.
User Manual DG LINK Application Program 071-0056-50 This document applies to firmware version 2.00 and above. www.tektronix.com Copyright Tektronix Japan, Ltd. All rights reserved. Copyright Tektronix,
More informationKPN SMS mail. Send SMS as fast as e-mail!
KPN SMS mail Send SMS as fast as e-mail! Quick start Start using KPN SMS mail in 5 steps If you want to install and use KPN SMS mail quickly, without reading the user guide, follow the next five steps.
More informationModel 288B Charge Plate Graphing Software Operators Guide
Monroe Electronics, Inc. Model 288B Charge Plate Graphing Software Operators Guide P/N 0340175 288BGraph (80207) Software V2.01 100 Housel Ave PO Box 535 Lyndonville NY 14098 1-800-821-6001 585-765-2254
More informationMicrosoft Powerpoint 2007 Keyboard Shortcuts
In the Help window F1 ALT+F4 ALT+ ALT+HOME Shift+, Shift+ Shift+ ALT LEFT ARROW or BACKSPACE ALT+RIGHT ARROW, PAGE UP, PAGE DOWN F5 CTRL+P Open the Help window in Microsoft Powerpoint. Close the Help window.
More informationMicrosoft Outlook 2003 Keyboard Shortcuts
In the Help Pane F1 F6 Shift+ and and ALT+ ALT+ CTRL+SPACE CTRL+F1 Display the Help Pane. Switch between the Help Pane and the active application. Select the next item in the Help Pane. Select the previous
More informationChapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
More informationExcel 2007 Basic knowledge
Ribbon menu The Ribbon menu system with tabs for various Excel commands. This Ribbon system replaces the traditional menus used with Excel 2003. Above the Ribbon in the upper-left corner is the Microsoft
More informationNIS-Elements Viewer. User's Guide
NIS-Elements Viewer User's Guide Publication date 10.09.2013 v. 4.20.00 Laboratory Imaging, s. r. o., Za Drahou 171/17, CZ - 102 00 Praha 10 No part of this publication may be reproduced or transmitted
More informationMicrosoft PowerPoint 2013 Keyboard shortcuts
Microsoft PowerPoint 2013 Keyboard shortcuts Online Help Keyboard Shortcuts for using the Help window The Help window provides access to all Office Help content. The Help window displays topics and other
More informationSage Abra SQL HRMS Reports. User Guide
Sage Abra SQL HRMS Reports User Guide 2010 Sage Software, Inc. All rights reserved. Sage, the Sage logos, and the Sage product and service names mentioned herein are registered trademarks or trademarks
More informationIntroduction to Microsoft Excel 2010
Introduction to Microsoft Excel 2010 Screen Elements Quick Access Toolbar The Ribbon Formula Bar Expand Formula Bar Button File Menu Vertical Scroll Worksheet Navigation Tabs Horizontal Scroll Bar Zoom
More informationTrace.Net OTDR Test Management Software User s guide
Trace.Net OTDR Test Management Software User s guide 2007-2009, AFL Telecommunications, all rights reserved. TRAC-01-1000 Revision B, 2009-06-10 Specifications are subject to change without notice. I Contents
More informationBIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005
BIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005 PLEASE NOTE: The contents of this publication, and any associated documentation provided to you, must not be disclosed to any third party without
More informationEmbroidery Fonts Plus ( EFP ) Tutorial Guide Version 1.0505
Embroidery Fonts Plus ( EFP ) Tutorial Guide Version 1.0505 1 Contents Chapter 1 System Requirements.................. 3 Chapter 2 Quick Start Installation.................. 4 System Requirements................
More informationGE Healthcare Life Sciences. PrimeView 5.31. User Manual
GE Healthcare Life Sciences PrimeView 5.3 User Manual Table of Contents Table of Contents Introducing PrimeView.... About PrimeView.... About this manual... PrimeView concepts.... Concept definitions....
More informationProject 2013 Keyboard Shortcuts
Project 2013 Keyboard Shortcuts Microsoft Office basics Keyboard access to the ribbon Alt. The KeyTips are displayed over each feature that is available in the current view. the letter that appears in
More informationVodafone PC SMS 2010. (Software version 4.7.1) User Manual
Vodafone PC SMS 2010 (Software version 4.7.1) User Manual July 19, 2010 Table of contents 1. Introduction...4 1.1 System Requirements... 4 1.2 Reply-to-Inbox... 4 1.3 What s new?... 4 2. Installation...6
More informationGEM. User Guide. Freedom Scientific, Inc. 440640-001 Rev. B
GEM User Guide Freedom Scientific, Inc. 440640-001 Rev. B PUBLISHED BY Freedom Scientific 11800 31 st Court North St. Petersburg, Florida 33716-1805 USA www.freedomscientific.com Information in this document
More informationkalmstrom.com Business Solutions
Kanban Task Manager for Outlook Manual Table of contents 1 INTRODUCTION... 3 1.1 LANGUAGES... 4 1.2 REQUIREMENTS... 4 1.3 SYSTEMS... 4 2 INSTALLATION OF KANBAN TASK MANAGER... 5 2.1 INTRODUCTION... 5 2.2
More informationPN-L702B LCD MONITOR TOUCH PANEL DRIVER OPERATION MANUAL. Version 2.1
PN-L702B LCD MONITOR TOUCH PANEL DRIVER OPERATION MANUAL Version 2.1 Contents Setting up the PC...3 Installing the touch panel driver...3 Touch Panel Settings...4 How to configure settings...4 Calibration...5
More informationUniversal Simple Control, USC-1
Universal Simple Control, USC-1 Data and Event Logging with the USB Flash Drive DATA-PAK The USC-1 universal simple voltage regulator control uses a flash drive to store data. Then a propriety Data and
More informationUser Guide. Introduction to 3M Digital Designs. User Guide Contents: Installing 3M Digital Designs Software. Setting up a Plotter
User Guide June 2008 Introduction to 3M Digital Designs 3M Digital Designs provides you with a convenient system for precision cutting of paint protection film kits. When these cut pieces are applied to
More informationMigrating to Excel 2010 from Excel 2003 - Excel - Microsoft Office 1 of 1
Migrating to Excel 2010 - Excel - Microsoft Office 1 of 1 In This Guide Microsoft Excel 2010 looks very different, so we created this guide to help you minimize the learning curve. Read on to learn key
More informationTips Tricks and Techniques for Efficient LabVIEW Development
Tips Tricks and Techniques for Efficient LabVIEW Development Presented by Nick Golas Telephonics Corp. IEEE I&M Society LI Section & Long Island LabVIEW Users Group (LILUG) Thursday 12/06/2007 Use the
More informationWHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT
WHAT S NEW IN WORD 2010 & HOW TO CUSTOMIZE IT The Ribbon... 2 Default Tabs... 2 Contextual Tabs... 2 Minimizing and Restoring the Ribbon... 3 Customizing the Ribbon... 3 A New Graphic Interface... 5 Live
More informationMake full use of WordFinder Pro for Mac!
Make full use of WordFinder Pro for Mac! Quick guide with useful tips and tricks Document version 1 2015 Technical specifications WordFinder 11 Pro for Mac requires: Processor: Intel Mac OS X 10.8 or later.
More informationUser Manual Microsoft Dynamics AX Add-on LabAX Label Printing
User Manual Microsoft Dynamics AX Add-on LabAX Label Printing Version 1.7 Last Update: 17.04.2011 User Manual Microsoft Dynamics AX Add-on LabAX Label Printing Page 2 / 23 Contents 1 Introduction... 3
More informationSurf it Easy. User Guide
Surf it Easy User Guide User Manual Version 1.1 2004 CoSoSys SRL Surf it Easy User Manual Table of Contents Table of Contents... I 1. Introduction... 1 2. System Requirements... 2 3. Installation... 2
More informationSTIM202 Evaluation Kit
Table of contents: 1 FEATURES... 2 2 GENERAL DESCRIPTIONS AND SYSTEM CONTENTS... 2 3 SYSTEM REQUIREMENTS... 2 4 GETTING STARTED... 3 4.1 INSTALLATION OF NI-SERIAL CABLE ASSEMBLY DRIVER... 3 4.2 INSTALLATION
More informationRegional Drought Decision Support System (RDDSS) Charting Tools Help Documentation
Regional Drought Decision Support System (RDDSS) Charting Tools Help Documentation The following help documentation was prepared to give insight to the basic functionality of the charting tools within
More informationContents. Microsoft Office 2010 Tutorial... 1
Microsoft Office 2010 Tutorial Contents Microsoft Office 2010 Tutorial... 1 Find your way through long documents with the new Document Navigation pane and Search... 4 Adjust the spaces between lines or
More informationKeyboard shortcuts in Excel 2010. Keyboard access to the ribbon. In this article WILL MY OLD SHORTCUTS STILL WORK? Hide All
Page 1 of 9 Excel > Accessibility Keyboard shortcuts in Excel 2010 Hide All This article describes what Key Tips are and how you can use them to access the ribbon. It also lists CTRL combination shortcut
More informationCenter for Teaching, Learning & Technology
Center for Teaching, Learning & Technology Faculty Technology Workshops Computer Management Albert Robinson / Delwar Sayeed Faculty and Staff Development Programs Center for Teaching, Learning & Technology
More informationBasic AutoSketch Manual
Basic AutoSketch Manual Instruction for students Skf-Manual.doc of 3 Contents BASIC AUTOSKETCH MANUAL... INSTRUCTION FOR STUDENTS... BASIC AUTOSKETCH INSTRUCTION... 3 SCREEN LAYOUT... 3 MENU BAR... 3 FILE
More informationE-Loader Operation Manual
Multi-Function Tools for E-MU Instruments Revision A _ Before you Begin - Read and follow the instructions given in the READ BEFORE INSTALLING file that comes with the E-Loader installer program. E-Loader
More informationUSER MANUAL SlimComputer
USER MANUAL SlimComputer 1 Contents Contents...2 What is SlimComputer?...2 Introduction...3 The Rating System...3 Buttons on the Main Interface...5 Running the Main Scan...8 Restore...11 Optimizer...14
More informationWindows XP Pro: Basics 1
NORTHWEST MISSOURI STATE UNIVERSITY ONLINE USER S GUIDE 2004 Windows XP Pro: Basics 1 Getting on the Northwest Network Getting on the Northwest network is easy with a university-provided PC, which has
More informationODBC Driver Version 4 Manual
ODBC Driver Version 4 Manual Revision Date 12/05/2007 HanDBase is a Registered Trademark of DDH Software, Inc. All information contained in this manual and all software applications mentioned in this manual
More information3. (1.0 point) To ungroup worksheets, you can click a sheet of a sheet not in the group. a. index b. panel c. tab d. pane
Excel Tutorial 6 1. (1.0 point) To select adjacent worksheets, you use the key. a. Shift b. Alt c. Ctrl d. F1 2. (1.0 point) The caption indicates a worksheet group. a. [Worksheets] b. [Selected Sheets]
More informationCastle Modeling. In this PDF tutorial we will be modeling a simple castle as pictured above.
Course: 3D Design Title: Castle Modeling Blender: Version 2.6X Level: Beginning Author; Neal Hirsig (nhirsig@tufts.edu) May, 2012 This tutorial assumes that you already know how to: Display orthographic
More information5. Tutorial. Starting FlashCut CNC
FlashCut CNC Section 5 Tutorial 259 5. Tutorial Starting FlashCut CNC To start FlashCut CNC, click on the Start button, select Programs, select FlashCut CNC 4, then select the FlashCut CNC 4 icon. A dialog
More informationKEYBOARD SHORTCUTS. Note: Keyboard shortcuts may be different for the same icon depending upon the SAP screen you are in.
KEYBOARD SHORTCUTS Instead of an SAP icon button, you can use a keyboard shortcut. A keyboard shortcut is a key or combination of keys that you can use to access icon button functions while you are working
More informationThe Center for Teaching, Learning, & Technology
The Center for Teaching, Learning, & Technology Instructional Technology Workshops Microsoft Excel 2010 Formulas and Charts Albert Robinson / Delwar Sayeed Faculty and Staff Development Programs Colston
More informationMicrosoft FrontPage 2003
Information Technology Services Kennesaw State University Microsoft FrontPage 2003 Information Technology Services Microsoft FrontPage Table of Contents Information Technology Services...1 Kennesaw State
More informationLegal Notes. Regarding Trademarks. 2012 KYOCERA Document Solutions Inc.
Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change without notice. We cannot be held liable for any problems arising from
More informationMicrosoft Excel 2010 Tutorial
1 Microsoft Excel 2010 Tutorial Excel is a spreadsheet program in the Microsoft Office system. You can use Excel to create and format workbooks (a collection of spreadsheets) in order to analyze data and
More informationUsing SQL Server Management Studio
Using SQL Server Management Studio Microsoft SQL Server Management Studio 2005 is a graphical tool for database designer or programmer. With SQL Server Management Studio 2005 you can: Create databases
More information2 SQL in iseries Navigator
2 SQL in iseries Navigator In V4R4, IBM added an SQL scripting tool to the standard features included within iseries Navigator and has continued enhancing it in subsequent releases. Because standard features
More informationStatgraphics Getting started
Statgraphics Getting started The aim of this exercise is to introduce you to some of the basic features of the Statgraphics software. Starting Statgraphics 1. Log in to your PC, using the usual procedure
More informationHandout: Word 2010 Tips and Shortcuts
Word 2010: Tips and Shortcuts Table of Contents EXPORT A CUSTOMIZED QUICK ACCESS TOOLBAR... 2 IMPORT A CUSTOMIZED QUICK ACCESS TOOLBAR... 2 USE THE FORMAT PAINTER... 3 REPEAT THE LAST ACTION... 3 SHOW
More informationLab - Using Wireshark to View Network Traffic
Topology Objectives Part 1: (Optional) Download and Install Wireshark Part 2: Capture and Analyze Local ICMP Data in Wireshark Start and stop data capture of ping traffic to local hosts. Locate the IP
More informationVersion of Barcode Toolbox adds support for Adobe Illustrator CS
Introduction Traditionally the printing industry has used manual design paste up and stripping for the implementation of barcode symbols but today the computer is used more often to generate barcode symbols
More informationUnderstand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
More informationMS Word 2007 practical notes
MS Word 2007 practical notes Contents Opening Microsoft Word 2007 in the practical room... 4 Screen Layout... 4 The Microsoft Office Button... 4 The Ribbon... 5 Quick Access Toolbar... 5 Moving in the
More informationBasics of MS Word :: 137
7 BASICS OF MS WORD 7.1 INTRODUCTION MS Word 2000 is an application program that allows you to create letters, reports, newsletters, tables, form letters, brochures, and Web pages. Using Word you can add
More informationOutlook Web App (OWA) Getting Started
Outlook Web App (OWA) Getting Started Accessing Outlook Web App You can access your mailbox through any browser. To access your mailbox, enter your OWA web address/url that was provided to you by your
More informationAfter starting the program, the Wizard appears. From its window, you can create a new analysis with the
bluevizia s Marketing Manager is a modern, easy-to-use software tool for the successful development and management of marketing processes. Installation Windows Double-click with the left mouse button on
More information1. Online help for WorkZone Client 2016 4. 2. What's new 5. 3. Getting started with WorkZone Client 13. 4. Working with the user interface 15
2016 Online help WorkZone Client 2016 Contents 1. Online help for WorkZone Client 2016 4 2. What's new 5 3. Getting started with WorkZone Client 13 4. Working with the user interface 15 4.1 Navigate the
More informationFile Management With Windows Explorer
File Management With Windows Explorer Preamble: After you have created and saved numerous files using various programs, file management, the process of organizing and keeping track of all your files, can
More informationGetting Started on the Computer With Mouseaerobics! Windows XP
This handout was modified from materials supplied by the Bill and Melinda Gates Foundation through a grant to the Manchester City Library. Getting Started on the Computer With Mouseaerobics! Windows XP
More informationSPROG II User Guide 1. SPROG II DCC Decoder Programmer User Guide
SPROG II User Guide 1 SPROG II DCC Decoder Programmer User Guide Firmware version 2.x December 2007 SPROG II User Guide 2 Table of Contents Introduction... 4 Requirements... 4 Requirements... 4 Features...
More informationIT Quick Reference Guides Using Windows 7
IT Quick Reference Guides Using Windows 7 Windows Guides This sheet covers many of the basic commands for using the Windows 7 operating system. WELCOME TO WINDOWS 7 After you log into your machine, the
More informationTechnical Publications. Author: Zultys Technical Support Department
September 09 MXMeeting User Guide Author: Zultys Technical Support Department MXMeeting is a multi-function web collaboration system. The client-server architecture requires Internet connectivity for its
More informationMicrosoft PowerPoint 2010
Microsoft PowerPoint 2010 Starting PowerPoint... 2 PowerPoint Window Properties... 2 The Ribbon... 3 Default Tabs... 3 Contextual Tabs... 3 Minimizing and Restoring the Ribbon... 4 The Backstage View...
More informationConnectivity Pack for Microsoft Guide
HP Vertica Analytic Database Software Version: 7.0.x Document Release Date: 2/20/2015 Legal Notices Warranty The only warranties for HP products and services are set forth in the express warranty statements
More informationJet Data Manager 2012 User Guide
Jet Data Manager 2012 User Guide Welcome This documentation provides descriptions of the concepts and features of the Jet Data Manager and how to use with them. With the Jet Data Manager you can transform
More informationNAND Flash Memories. Using Linux MTD compatible mode. on ELNEC Universal Device Programmers. (Quick Guide)
NAND Flash Memories Using Linux MTD compatible mode on ELNEC Universal Device Programmers (Quick Guide) Application Note April 2012 an_elnec_linux_mtd, version 1.04 Version 1.04/04.2012 Page 1 of 16 As
More informationKaleidaGraph Quick Start Guide
KaleidaGraph Quick Start Guide This document is a hands-on guide that walks you through the use of KaleidaGraph. You will probably want to print this guide and then start your exploration of the product.
More informationMetadata Import Plugin User manual
Metadata Import Plugin User manual User manual for Metadata Import Plugin 1.0 Windows, Mac OS X and Linux August 30, 2013 This software is for research purposes only. CLC bio Silkeborgvej 2 Prismet DK-8000
More informationYears after 2000. US Student to Teacher Ratio 0 16.048 1 15.893 2 15.900 3 15.900 4 15.800 5 15.657 6 15.540
To complete this technology assignment, you should already have created a scatter plot for your data on your calculator and/or in Excel. You could do this with any two columns of data, but for demonstration
More informationModel SL355 Noise Dosimeter/Datalogger
Model SL355 Noise Dosimeter/Datalogger Software Help Guide Software Introduction The SL355 Noise Dosimeter software allows for setup and retrieval of recorded data in the Noise Dosimeter. A total of 20
More informationCM HOST CM CardTransporter Fuel Communication and Management Software 10.10.06 Software version up to 3.1
CM HOST CM CardTransporter Fuel Communication and Management Software 10.10.06 Software version up to 3.1 CM Host Manual For CardMaster Fuel Control www.cardlockvending.com customers call 888-487-5040
More informationMicrosoft Access 97 Keyboard Shortcuts
CTRL+ or CTRL+Shift+ ALT+ number (where hitting key for 1 selects the leftmost option, 2 the next, and so on) ALT+0(ZERO) ALT+B ALT+ in Datasheet view and Move Mode, move the selected column to the right
More informationWord 2010: The Basics Table of Contents THE WORD 2010 WINDOW... 2 SET UP A DOCUMENT... 3 INTRODUCING BACKSTAGE... 3 CREATE A NEW DOCUMENT...
Word 2010: The Basics Table of Contents THE WORD 2010 WINDOW... 2 SET UP A DOCUMENT... 3 INTRODUCING BACKSTAGE... 3 CREATE A NEW DOCUMENT... 4 Open a blank document... 4 Start a document from a template...
More informationAppendix K Introduction to Microsoft Visual C++ 6.0
Appendix K Introduction to Microsoft Visual C++ 6.0 This appendix serves as a quick reference for performing the following operations using the Microsoft Visual C++ integrated development environment (IDE):
More informationELFRING FONTS UPC BAR CODES
ELFRING FONTS UPC BAR CODES This package includes five UPC-A and five UPC-E bar code fonts in both TrueType and PostScript formats, a Windows utility, BarUPC, which helps you make bar codes, and Visual
More informationNETWORK PRINT MONITOR User Guide
NETWORK PRINT MONITOR User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change without notice. We cannot be held liable
More informationEXERCISE 3: String Variables and ASCII Code
EXERCISE 3: String Variables and ASCII Code EXERCISE OBJECTIVE When you have completed this exercise, you will be able to describe the use of string variable and ASCII code. You will use Flowcode and the
More informationQuick Start Using DASYLab with your Measurement Computing USB device
Quick Start Using DASYLab with your Measurement Computing USB device Thank you for purchasing a USB data acquisition device from Measurement Computing Corporation (MCC). This Quick Start document contains
More informationGestation Period as a function of Lifespan
This document will show a number of tricks that can be done in Minitab to make attractive graphs. We work first with the file X:\SOR\24\M\ANIMALS.MTP. This first picture was obtained through Graph Plot.
More informationPowerPoint 2007 Basics Website: http://etc.usf.edu/te/
Website: http://etc.usf.edu/te/ PowerPoint is the presentation program included in the Microsoft Office suite. With PowerPoint, you can create engaging presentations that can be presented in person, online,
More informationExcel. Microsoft Office s spreadsheet application can be used to track. and analyze numerical data for display on screen or in printed
Excel Microsoft Office s spreadsheet application can be used to track and analyze numerical data for display on screen or in printed format. Excel is designed to help you record and calculate data, and
More informationDriveClone Server. Users Manual
DriveClone Server Users Manual Contents Chapter 1: Introduction... 3 Chapter 2: Install and uninstall DriveClone Server... 3 2.1 System Requirement... 3 2.2 Installing DriveClone Server... 4 2.3 Uninstalling
More informationCrystal Print Control Installation Instructions for PCs running Microsoft Windows XP and using the Internet Explorer browser
Crystal Print Control Installation Instructions for PCs running Microsoft Windows XP and using the Internet Explorer browser Important Notice: You must have administrative rights to your PC to perform
More informationMicrosoft Excel 2007. Introduction to Microsoft Excel 2007
Microsoft Excel 2007 Introduction to Microsoft Excel 2007 Excel is an electronic spreadsheet to organize your data into rows and columns. One can use it to perform basic to advanced level mathematical
More informationThere are six different windows that can be opened when using SPSS. The following will give a description of each of them.
SPSS Basics Tutorial 1: SPSS Windows There are six different windows that can be opened when using SPSS. The following will give a description of each of them. The Data Editor The Data Editor is a spreadsheet
More information13-1. This chapter explains how to use different objects.
13-1 13.Objects This chapter explains how to use different objects. 13.1. Bit Lamp... 13-3 13.2. Word Lamp... 13-5 13.3. Set Bit... 13-9 13.4. Set Word... 13-11 13.5. Function Key... 13-18 13.6. Toggle
More informationRFID Logger Software User Manual Rev 1.0
RFID Logger Software User Manual Rev 1.0 Table of Contents 1. System Overview... 2 2. Installation... 2 3. USB RFID Interface Box... 3 4. Operation... 4 4.1. Start Up... 4 4.2. Menu overview... 4 4.2.1.
More informationFP File Organizer 3.0 Instruction Manual
FP File Organizer 3.0 Instruction Manual Field Precision LLC PO Box 13595, Albuquerque, NM 87192 U.S.A. Telephone: +1-505-220-3975 Fax: +1-617-752-9077 E mail: techinfo@fieldp.com Internet: http://www.fieldp.com
More informationTNM Programmer 5000. User Manual. For Windows 7 / Vista / XP. TNM Electronics Ltd. www.tnmelectronics.com\english\5000.html
TNM Programmer 5000 For Windows 7 / Vista / XP User Manual TNM Electronics Ltd. www.tnmelectronics.com\english\5000.html 1 Contents 1. System Requirements. 2. Software Setup. - Installation from the TNM
More informationSC Analysis Software. The software provides 5 main functions:
SC Analysis Software Contents 1. Introduction 2. Rowing Record 3. Installing Software 4. Connecting to PC 5. Selecting a Record 6. Chart a Record 7. Display Splits 8. Setting Up SC 9. Synchronised Video
More informationIntro to Excel spreadsheets
Intro to Excel spreadsheets What are the objectives of this document? The objectives of document are: 1. Familiarize you with what a spreadsheet is, how it works, and what its capabilities are; 2. Using
More informationA computer running Windows Vista or Mac OS X
lab File Management Objectives: Upon successful completion of Lab 2, you will be able to Define the terms file and folder Understand file and memory storage capacity concepts including byte, kilobyte,
More informationACTIVE@ UNDELETE 7.0 USER GUIDE
ACTIVE@ UNDELETE 7.0 USER GUIDE COPYRIGHT Copyright 27, LSOFT TECHNOLOGIES INC. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative
More informationVisualization with Excel Tools and Microsoft Azure
Visualization with Excel Tools and Microsoft Azure Introduction Power Query and Power Map are add-ins that are available as free downloads from Microsoft to enhance the data access and data visualization
More information