JFET Input Instrumentation Amplifier with Rail-to-Rail Output in MSOP Package AD8220
|
|
- Alexandrina Day
- 7 years ago
- Views:
Transcription
1 JFET Input Instrumentation Amplifier with Rail-to-Rail Output in MSOP Package AD8 FEATURES Low input currents pa maximum input bias current (B grade).6 pa maximum input offset current (B grade) High CMRR db CMRR (minimum), G = (B grade) 8 db CMRR (minimum) to 5 khz, G = (B grade) Excellent ac specifications and low power.5 MHz bandwidth (G = ) 4 nv/ Hz input noise ( khz) Slew rate: V/μs 75 μa quiescent supply current (maximum) Versatile MSOP package Rail-to-rail output Input voltage range to below negative supply rail 4 kv ESD protection 4.5 V to 36 V single supply ±.5 V to ±8 V dual supply Gain set with single resistor (G = to ) Qualified for automotive applications APPLICATIONS Medical instrumentation Precision data acquisition Transducer interfaces GENERAL DESCRIPTION The AD8 is the first single-supply, JFET input instrumentation amplifier available in an MSOP package. Designed to meet the needs of high performance, portable instrumentation, the AD8 has a minimum common-mode rejection ratio (CMRR) of 86 db at dc and a minimum CMRR of 8 db at 5 khz for G =. Maximum input bias current is pa and typically remains below 3 pa over the entire industrial temperature range. Despite the JFET inputs, the AD8 typically has a noise corner of only Hz. With the proliferation of mixed-signal processing, the number of power supplies required in each system has grown. The AD8 is designed to alleviate this problem. The AD8 can operate on a ±8 V dual supply, as well as on a single +5 V supply. Its rail-to-rail output stage maximizes dynamic range on the low voltage supplies common in portable applications. Its ability to run on a single 5 V supply eliminates the need to use higher voltage, dual supplies. The AD8 draws a maximum of 75 μa of quiescent current, making it ideal for battery powered devices. INPUT BIAS CURRENT (A) n n p p p.p PIN CONFIGURATION IN R G R G 3 +IN 4 AD8 TOP VIEW (Not to Scale) Figure I BIAS +V S V OUT TEMPERATURE ( C) Figure. Input Bias Current and Offset Current vs. Temperature Gain is set from to with a single resistor. Increasing the gain increases the common-mode rejection. Measurements that need higher CMRR when reading small signals benefit when the AD8 is set for large gains. A reference pin allows the user to offset the output voltage. This feature is useful when interfacing with analog-to-digital converters. The AD8 is available in an MSOP that takes roughly half the board area of an SOIC. Performance for the A and B grade is specified over the industrial temperature range of 4 C to +85 C, and the W grade is specified over the automotive temperature range of 4 C to +5 C. I OS Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 96, Norwood, MA 6-96, U.S.A. Tel: Fax: Analog Devices, Inc. All rights reserved.
2 TABLE OF CONTENTS Features... Applications... Pin Configuration... General Description... Revision History... Specifications... 3 Absolute Maximum Ratings... 8 ESD Caution... 8 Pin Configuration and Function Descriptions... 9 Typical Performance Characteristics... Theory of Operation... 9 Gain Selection... Layout... Reference Terminal... Power Supply Regulation and Bypassing... Input Bias Current Return Path... Input Protection... RF Interference... Common-Mode Input Voltage Range... Driving an ADC... Applications Information... 3 AC-Coupled Instrumentation Amplifier... 3 Differential Output... 3 Electrocardiogram Signal Conditioning... 5 Outline Dimensions... 6 Ordering Guide... 6 Automotive Products... 6 REVISION HISTORY 5/ Rev. A to Rev. B Added W Grade... Universal Changes to Features Section and General Description Section. Changes to Specifications Section and Table... 3 Changes to Table... 5 Updated Outline Dimensions... 6 Changes to Ordering Guide... 6 Added Automotive Products Section /7 Rev. to Rev. A Changes to Table... 3 Changes to Table... 5 Changes to Table Changes to Figure 6 and Figure 7... Changes to Figure 3 and Figure Changes to Theory of Operation... 9 Changes to Layout... Changes to Ordering Guide /6 Revision : Initial Version Rev. B Page of 8
3 SPECIFICATIONS VS+ = 5 V, VS = 5 V, V = V, TA = 5 C, TOPR = 4 C to +85 C for A and B grades. TOPR = 4 C to +5 C for W grade, G =, RL = kω, unless otherwise noted. AD8 Table. A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit COMMON-MODE REJECTION RATIO (CMRR) TA for A, B grades, TOPR for W grade CMRR DC to 6 Hz with VCM = ± V kω Source Imbalance G = db G = 94 9 db G = 94 9 db G = 94 9 db CMRR at 5 khz VCM = ± V G = db G = db G = db G = db NOISE RTI noise = (eni + (eno/g) ), TA Voltage Noise, khz Input Voltage Noise, eni VIN+, VIN = V nv/ Hz Output Voltage Noise, eno VIN+, VIN = V nv/ Hz RTI,. Hz to Hz G = μv p-p G = μv p-p Current Noise f = khz fa/ Hz VOLTAGE OFFSET VOS = VOSI + VOSO/G Input Offset, VOSI TA μv Average TC TOPR μv/ C Output Offset, VOSO TA μv Average TC TOPR μv/ C Offset RTI vs. Supply (PSR) VS = ±5 V to ±5 V, TA for A, B grades, TOPR for W grade G = db G = 96 9 db G = 96 9 db G = 96 9 db INPUT CURRENT Input Bias Current TA 5 5 pa Over Temperature TOPR.3.3 na Input Offset Current TA.6 pa Over Temperature TOPR.5.5 na DYNAMIC RESPONSE Small Signal Bandwidth, TA 3 db G = khz G = khz G = khz G = khz Rev. B Page 3 of 8
4 A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit Settling Time.% V step, TA G = μs G = μs G = μs G = μs Settling Time.% V step, TA G = μs G = μs G = μs G = μs Slew Rate G = to TA V/μs GAIN G = + (49.4 kω/rg), TA for A, B grades, TOPR for W grade Gain Range V/V Gain Error VOUT = ± V G = % G = % G = % G = % Gain Nonlinearity VOUT = V to + V, TA G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm Gain vs. Temperature G = ppm/ C G > ppm/ C INPUT Impedance (Pin to TA GΩ pf Ground) Input Operating Voltage Range 3 VS = ±.5 V to ±8 V for dual supplies VS. +VS VS. +VS VS. +VS V Over Temperature TOPR VS. OUTPUT Output Swing RL = kω, TA V Over Temperature TOPR V Short-Circuit Current TA ma ERENCE INPUT TA kω RIN μa IIN VIN+, VIN = V V Voltage Range VS +VS VS +VS +VS V/V Gain to Output TA ±. +VS. VS. ±. +VS. VS. +VS. ±. V V/V Rev. B Page 4 of 8
5 A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit POWER SUPPLY V Operating Range ±.5 4 ±8 ±.5 4 ±8 ±.5 4 ±8 μa Quiescent Current TA μa Over Temperature TOPR μa TEMPERATURE RANGE For Specified Performance TOPR C When the output sinks more than 4 ma, use a 47 pf capacitor in parallel with the load to prevent ringing. Otherwise, use a larger load, such as kω. Differential and common-mode input impedance can be calculated from the pin impedance: ZDIFF = (ZPIN); ZCM = ZPIN/. 3 The AD8 can operate up to a diode drop below the negative supply but the bias current increases sharply. The input voltage range reflects the maximum allowable voltage where the input bias current is within the specification. 4 At this supply voltage, ensure that the input common-mode voltage is within the input voltage range specification. VS + = 5 V, VS = V, V =.5 V, TA = 5 C, TOPR = 4 C to +85 C for A and B grades. TOPR = 4 C to +5 C for W grade, G =, RL = kω, unless otherwise noted. Table. A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit COMMON-MODE REJECTION RATIO (CMRR) TA for A, B grades, TOPR for W grade CMRR DC to 6 Hz with VCM = to.5 V kω Source Imbalance G = db G = 94 9 db G = 94 9 db G = 94 9 db CMRR at 5 khz VCM = to.5 V G = db G = db G = db G = db NOISE RTI noise = (eni + (eno/g) ), TA Voltage Noise, khz VS = ±.5 V Input Voltage Noise, eni VIN+, VIN = V, V = nv/ Hz V Output Voltage Noise, eno VIN+, VIN = V, V = nv/ Hz V RTI,. Hz to Hz G = μv p-p G = μv p-p Current Noise f = khz fa/ Hz VOLTAGE OFFSET VOS = VOSI + VOSO/G Input Offset, VOSI TA μv Average TC TOPR μv/ C Output Offset, VOSO TA μv Average TC TOPR μv/ C Offset RTI vs. Supply (PSR) TA for A, B grades, TOPR for W grade G = db G = 96 9 db G = 96 9 db G = 96 9 db Rev. B Page 5 of 8
6 A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit INPUT CURRENT Input Bias Current TA 5 5 pa Over Temperature TOPR.3.3 na Input Offset Current TA.6 pa Over Temperature TOPR.5.5 na DYNAMIC RESPONSE TA Small Signal Bandwidth, 3 db G = khz G = khz G = khz G = khz Settling Time.% TA G = 3 V step μs G = 4 V step μs G = 4 V step μs G = 4 V step μs Settling Time.% TA G = 3 V step μs G = 4 V step μs G = 4 V step μs G = 4 V step μs Slew Rate G = to TA V/μs GAIN G = + (49.4 kω/rg), TA for A, B grades, TOPR for W grade Gain Range V/V Gain Error VOUT =.3 V to.9 V for G =, VOUT =.3 V to 3.8 V for G > G = % G = % G = % G = % Nonlinearity VOUT =.3 V to.9 V for G =, VOUT =.3 V to 3.8 V for G >, TA G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm G = RL = kω ppm Gain vs. Temperature G = ppm/ C G > ppm/ C INPUT Impedance (Pin to TA GΩ pf Ground) Input Voltage Range 3 TA. +VS. +VS V Over Temperature TOPR. +VS.. +VS.. +VS. V Rev. B Page 6 of 8
7 A Grade B Grade W Grade Parameter Test Conditions Min Typ Max Min Typ Max Min Typ Max Unit OUTPUT Output Swing RL = kω V Over Temperature TOPR V Short-Circuit Current ma ERENCE INPUT TA RIN kω IIN VIN+, VIN = V μa Voltage Range VS +VS VS +VS VS +VS V Gain to Output TA ±. ±. ±. POWER SUPPLY Operating Range V Quiescent Current TA μa Over Temperature TOPR μa TEMPERATURE RANGE TOPR, For Specified Performance TOPR C When the output sinks more than 4 ma, use a 47 pf capacitor in parallel with the load to prevent ringing. Otherwise, use a larger load, such as kω. Differential and common-mode impedance can be calculated from the pin impedance: ZDIFF = (ZPIN); ZCM = ZPIN/. 3 The AD8 can operate up to a diode drop below the negative supply but the bias current increases sharply. The input voltage range reflects the maximum allowable voltage where the input bias current is within the specification. V/V Rev. B Page 7 of 8
8 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Rating Supply Voltage ±8 V Power Dissipation See Figure 3 Output Short-Circuit Current Indefinite Input Voltage (Common Mode) ±Vs Differential Input Voltage ±Vs Storage Temperature Range 65 C to +5 C Operating Temperature Range 4 C to +5 C Lead Temperature (Soldering sec) 3 C Junction Temperature 4 C θja (4-Layer JEDEC Standard Board) 35 C/W Package Glass Transition Temperature 4 C ESD (Human Body Model) 4 kv ESD (Charge Device Model) kv ESD (Machine Model).4 kv Assumes the load is referenced to midsupply. Temperature for specified performance is 4 C to +85 C. For performance to 5 C, see the Typical Performance Characteristics section. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Figure 3 shows the maximum safe power dissipation in the package vs. the ambient temperature for the MSOP on a 4-layer JEDEC standard board. θja values are approximations. MAXIMUM POWER DISSIPATION (W) AMBIENT TEMPERATURE ( C) Figure 3. Maximum Power Dissipation vs. Ambient Temperature ESD CAUTION Rev. B Page 8 of 8
9 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS IN AD8 8 +V S R G 7 V OUT R G 3 6 +IN 4 5 TOP VIEW (Not to Scale) Figure 4. Pin Configuration Table 4. Pin Function Descriptions Pin No. Mnemonic Description IN Negative Input Terminal (True Differential Input), 3 RG Gain Setting Terminals (Place Resistor Across the RG Pins) 4 +IN Positive Input Terminal (True Differential Input) 5 VS Negative Power Supply Terminal 6 Reference Voltage Terminal (Drive This Terminal with a Low Impedance Voltage Source to Level-Shift the Output) 7 VOUT Output Terminal 8 +VS Positive Power Supply Terminal Rev. B Page 9 of 8
10 TYPICAL PERFORMANCE CHARACTERISTICS 6 4 NUMBER OF UNITS NUMBER OF UNITS CMRR (µv/v) I BIAS (pa) Figure 5. Typical Distribution of CMRR (G = ) Figure 8. Typical Distribution of Input Bias Current NUMBER OF UNITS NUMBER OF UNITS V OSI (µv) Figure 6. Typical Distribution of Input Offset Voltage I OS (pa) Figure 9. Typical Distribution of Input Offset Current NUMBER OF UNITS VOLTAGE NOISE RTI (nv/ Hz) GAIN = BANDWIDTH ROLL-OFF GAIN = GAIN = GAIN = /GAIN = GAIN = BANDWIDTH ROLL-OFF 5 5 V OSO (µv) Figure 7. Typical Distribution of Output Offset Voltage k k k FREQUENCY (Hz) Figure. Voltage Spectral Density vs. Frequency Rev. B Page of 8
11 5 3 GAIN = GAIN = BANDWIDTH LIMITED X (X) PSRR (db) 9 7 GAIN = GAIN = 5 5µV/DIV X (X) Figure.. Hz to Hz RTI Voltage Noise (G = ) s/div k k k M FREQUENCY (Hz) Figure 4. Positive PSRR vs. Frequency, RTI GAIN = X (X) PSRR (db) 9 7 GAIN = GAIN = 5 GAIN = µv/div s/div k k k M X (X) Figure.. Hz to Hz RTI Voltage Noise (G = ) FREQUENCY (Hz) Figure 5. Negative PSRR vs. Frequency, RTI Δ V OSI (µv) k TIME (s) Figure 3. Change in Input Offset Voltage vs. Warmup Time INPUT BIAS CURRENT (pa) INPUT OFFSET CURRENT ±5 5.V 5.V INPUT OFFSET CURRENT ±5 INPUT BIAS CURRENT ± COMMON-MODE VOLTAGE (V) INPUT BIAS CURRENT ±5 Figure 6. Input Bias Current and Input Offset Current vs. Common-Mode Voltage INPUT OFFSET CURRENT (pa) Rev. B Page of 8
12 6 INPUT BIAS CURRENT (A) n n p p p I BIAS I OS CMRR (db) 4 8 GAIN = GAIN = GAIN = GAIN = BANDWIDTH LIMITED.p TEMPERATURE ( C) Figure 7. Input Bias Current and Offset Current vs. Temperature, VS = ±5 V, V = V k k k FREQUENCY (Hz) Figure. CMRR vs. Frequency, kω Source Imbalance n 8 6 CURRENT (A) n p p p I BIAS I OS Δ CMRR (μv/v) 4 4.p TEMPERATURE ( C) Figure 8. Input Bias Current and Offset Current vs. Temperature, VS = +5 V, V =.5 V TEMPERATURE ( C) Figure. Change in CMRR vs. Temperature, G = GAIN = 6 5 GAIN = GAIN = 4 3 GAIN = CMRR (db) 8 GAIN = GAIN = BANDWIDTH LIMITED GAIN (db) GAIN = GAIN = 6 4 k k k FREQUENCY (Hz) Figure 9. CMRR vs. Frequency k k k M M FREQUENCY (Hz) Figure. Gain vs. Frequency Rev. B Page of 8
13 X NONLINEARITY (5ppm/DIV) R LOAD = kω R LOAD = kω X NONLINEARITY (5ppm/DIV) R LOAD =kω R LOAD =kω V S = ±5V V S = ±5V OUTPUT VOLTAGE (V) Figure 3. Gain Nonlinearity, G = OUTPUT VOLTAGE (V) Figure 6. Gain Nonlinearity, G = 8 X NONLINEARITY (5ppm/DIV) V S = ±5V R LOAD = kω OUTPUT VOLTAGE (V) R LOAD = kω Figure 4. Gain Nonlinearity, G = INPUT COMMON-MODE VOLTAGE (V) 6 6 ±5V SUPPLIES 4.8V, +5.5V 4.8V, +.6V 4.8V, 3.3V 4.8V, 8.3V +3V +3V ±5V SUPPLIES 5.3V 5.3V OUTPUT VOLTAGE (V) +4.9V, +5.5V +4.95V, +.6V +4.95V, 3.3V +4.9V, 8.3V Figure 7. Input Common-Mode Voltage Range vs. Output Voltage, G =, V = V X NONLINEARITY (5ppm/DIV) V S = ±5V R LOAD = kω OUTPUT VOLTAGE (V) R LOAD =kω Figure 5. Gain Nonlinearity, G = INPUT COMMON-MODE VOLTAGE (V) 3 +.V, +.7V +.V, +.5V +3V SINGLESUPPLY, V = +.5V.3V OUTPUT VOLTAGE (V) +4.9V, +.7V +4.9V, +.5V Figure 8. Input Common-Mode Voltage Range vs. Output Voltage, G =, VS = +5 V, V =.5 V Rev. B Page 3 of 8
14 INPUT COMMON-MODE VOLTAGE (V) INPUT COMMON-MODE VOLTAGE (V) ±5V SUPPLIES 4.9V, +5.4V 4.9V, +.4V 4.9V, 4.V 4.8V, 9V +3V 5.3V +3V ±5V SUPPLIES 5.3V OUTPUT VOLTAGE (V) +4.9V, +5.4V +4.9V, +.5V +4.9V, 4.V +4.9V, 9V Figure 9. Input Common-Mode Voltage Range vs. Output Voltage, G =, V = V V, +.7V +.V,.5V +3V SINGLE SUPPLY, V = +.5V.3V OUTPUT VOLTAGE (V) +4.9V, +.7V +4.9V,.5V Figure 3. Input Common-Mode Voltage Range vs. Output Voltage, G =, VS = +5 V, V =.5 V V S OUTPUT VOLTAGE SWING (V) ERRED TO SUPPLY VOLTAGE V S C 4 C +5 C +85 C +5 C +85 C +5 C 4 C V S DUAL SUPPLY VOLTAGE (±V) Figure 3. Output Voltage Swing vs. Supply Voltage, RLOAD = kω, G =, V = V OUTPUT VOLTAGE SWING (V) ERRED TO SUPPLY VOLTAGE V S V S DUAL SUPPLY VOLTAGE (±V) Figure 33. Output Voltage Swing vs. Supply Voltage, RLOAD = kω, G =, V = V 5 +5 C +85 C +5 C 4 C +5 C +85 C +5 C 4 C INPUT VOLTAGE LIMIT (V) + V S 4 C +5 C +5 C +85 C NOTES. THE AD8 CAN OPERATE UP TO A V BE BELOW THE NEGATIVE SUPPLY, BUT THE BIAS CURRENT WILL INCREASE SHARPLY. 4 C +5 C +85 C +5 C SUPPLY VOLTAGE (V) Figure 3. Input Voltage Limit vs. Supply Voltage, G =, V = V OUTPUT VOLTAGE SWING (V) C 4 C +5 C +5 C +85 C +85 C +5 C 4 C 5 k k R LOAD (Ω) Figure 34. Output Voltage Swing vs. Load Resistance VS = ±5 V, V = V Rev. B Page 4 of 8
15 OUTPUT VOLTAGE SWING (V) 5 4 C +85 C 4 +5 C +5 C 3 +5 C +5 C +85 C 4 C k k R LOAD (Ω) Figure 35. Output Voltage Swing vs. Load Resistance VS = +5 V, V =.5 V X (X) NO LOAD mv/div 47pF 5µs/DIV pf X (X) Figure 38. Small Signal Pulse Response for Various Capacitive Loads, VS = ±5 V, V = V V S + OUTPUT VOLTAGE SWING (V) ERRED TO SUPPLY VOLTAGES C 4 C +85 C +5 C +5 C +85 C +5 C X (X) NO LOAD 47pF pf + 4 C V S I OUT (ma) Figure 36. Output Voltage Swing vs. Output Current, VS = ±5 V, V = V OUTPUT VOLTAGE SWING (V) ERRED TO SUPPLY VOLTAGES V S C +5 C +85 C +85 C +5 C +5 C 4 C V S I OUT (ma) Figure 37. Output Voltage Swing vs. Output Current, VS = 5 V, V =.5 V mv/div 5µs/DIV X (X) Figure 39. Small Signal Pulse Response for Various Capacitive Loads, VS = 5 V, V =.5 V OUTPUT VOLTAGE SWING (V p-p) GAIN =,, GAIN = k k k M M FREQUENCY (Hz) Figure 4. Output Voltage Swing vs. Large Signal Frequency Response Rev. B Page 5 of 8
16 5V/DIV 5V/DIV X (X).%/DIV 5µs TO.% 6µs TO.% µs/div X (X) Figure 4. Large Signal Pulse Response and Settle Time, G =, RLOAD = kω, VS = ±5 V, V = V V/DIV X (X).%/DIV 4.3μs TO.% 4.6μs TO.% X (X) µs/div Figure 4. Large Signal Pulse Response and Settle Time, G =, RLOAD = kω, VS = ±5 V, V = V X (X) X (X).%/DIV 58μs TO.% 74μs TO.% X (X) µs/div Figure 44. Large Signal Pulse Response and Settle Time, G =, RLOAD = kω, VS = ±5 V, V = V X mv/div X 4µs/DIV Figure 45. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = ±5 V, V = V 5V/DIV X.%/DIV 8.μs TO.% 9.6μs TO.% mv/div X (X) µs/div Figure 43. Large Signal Pulse Response and Settle Time, G =, RLOAD = kω, VS = ±5 V, V = V X 4µs/DIV Figure 46. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = ±5 V, V = V Rev. B Page 6 of 8
17 X mv/div X 4µs/DIV Figure 47 Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = ±5 V, V = V X mv/div X 4µs/DIV Figure 48. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = ±5 V, V = V X X mv/div X 4µs/DIV Figure 5. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = 5 V, V =.5 V X mv/div X 4µs/DIV Figure 5. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = 5 V, V =.5 V X mv/div mv/div X 4µs/DIV Figure 49. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = 5 V, V =.5 V X 4µs/DIV Figure 5. Small Signal Pulse Response, G =, RLOAD = kω, CLOAD = pf, VS = 5 V, V =.5 V Rev. B Page 7 of 8
18 5 SETTLING TIME (µs) 5 SETTLED TO.% SETTLED TO.% SETTLING TIME (µs) SETTLED TO.% SETTLED TO.% 5 5 OUTPUT VOLTAGE STEP SIZE (V) Figure 53. Settling Time vs. Output Voltage Step Size (G = ) ±5 V, V = V GAIN (V/V) Figure 54. Settling Time vs. Gain for a V Step, VS = ±5 V, V = V Rev. B Page 8 of 8
19 THEORY OF OPERATION +V S +V S +V S +V S NODE A R G NODE B kω R 4.7kΩ R 4.7kΩ kω kω NODE F A3 +V S OUTPUT +V S +V S NODE C NODE D NODE E +V S +IN J Q C C Q J IN kω V PINCH A A V PINCH I VB I Figure 55. Simplified Schematic The AD8 is a JFET input, monolithic instrumentation amplifier based on the classic 3-op amp topology (see Figure 55). Input Transistor J and Input Transistor J are biased at a fixed current so that any input signal forces the output voltages of A and A to change accordingly; the input signal creates a current through RG that flows in R and R such that the outputs of A and A provide the correct, gained signal. Topologically, J, A, and R and J, A, and R can be viewed as precision current feedback amplifiers that have a gain bandwidth of.5 MHz. The common-mode voltage and amplified differential signal from A and A are applied to a difference amplifier that rejects the common-mode voltage but amplifies the differential signal. The difference amplifier employs kω laser-trimmed resistors that result in an in-amp with gain error less than.4%. New trim techniques were developed to ensure that CMRR exceeds 86 db (G = ). Using JFET transistors, the AD8 offers an extremely high input impedance, extremely low bias currents of pa maximum, a low offset current of.6 pa maximum, and no input bias current noise. In addition, input offset is less than 5 μv and drift is less than 5 μv/ C. Ease of use and robustness were considered. A common problem for instrumentation amplifiers is that at high gains, when the input is overdriven, an excessive milliampere input bias current can result and the output can undergo phase reversal. The AD8 has none of these problems; its input bias current is limited to less than μa, and the output does not phase reverse under overdrive fault conditions. Overdriving the input at high gains refers to when the input signal is within the supply voltages but the amplifier cannot output the gained signal. For example, at a gain of, driving the amplifier with V on ±5 V constitutes overdriving the inputs since the amplifier cannot output V. The AD8 has extremely low load-induced nonlinearity. All amplifiers that comprise the AD8 have rail-to-rail output capability for enhanced dynamic range. The input of the AD8 can amplify signals with wide common-mode voltages even slightly lower than the negative supply rail. The AD8 operates over a wide supply voltage range. It can operate from either a single +4.5 V to +36 V supply or a dual ±.5 V to ±8 V. The transfer function of the AD8 is 49.4 kω G R G Users can easily and accurately set the gain using a single, standard resistor. Because the input amplifiers employ a current feedback architecture, the AD8 gain-bandwidth product increases with gain, resulting in a system that does not suffer as much bandwidth loss as voltage feedback architectures at higher gains. A unique pinout enables the AD8 to meet a CMRR specification of 8 db through 5 khz (G = ). The balanced pinout, shown in Figure 56, reduces parasitics that adversely affect CMRR performance. In addition, the new pinout simplifies board layout because associated traces are grouped together. For example, the gain setting resistor pins are adjacent to the inputs, and the reference pin is next to the output. IN R G R G 3 +IN 4 AD8 +V S TOP VIEW (Not to Scale) Figure 56. Pin Configuration V OUT Rev. B Page 9 of 8
20 GAIN SELECTION Placing a resistor across the RG terminals sets the AD8 gain, which can be calculated by referring to Table 5 or by using the gain equation RG 49.4 kω G Table 5. Gains Achieved Using % Resistors % Standard Table Value of RG (Ω) Calculated Gain 49.9 k.99.4 k k k k The AD8 defaults to G = when no gain resistor is used. Gain accuracy is determined by the absolute tolerance of RG. The TC of the external gain resistor increases the gain drift of the instrumentation amplifier. Gain error and gain drift are kept to a minimum when the gain resistor is not used. LAYOUT Careful board layout maximizes system performance. In applications that need to take advantage of the low input bias current of the AD8, avoid placing metal under the input path to minimize leakage current. To maintain high CMRR over frequency, lay out the input traces symmetrically and lay out the traces of the RG resistor symmetrically. Ensure that the traces maintain resistive and capacitive balance; this holds for additional PCB metal layers under the input and RG pins. Traces from the gain setting resistor to the RG pins should be kept as short as possible to minimize parasitic inductance. An example layout is shown in Figure 57 and Figure 58. To ensure the most accurate output, the trace from the pin should either be connected to the AD8 local ground (see Figure 59) or connected to a voltage that is referenced to the AD8 local ground. Common-Mode Rejection Ratio (CMRR) The AD8 has high CMRR over frequency giving it greater immunity to disturbances, such as line noise and its associated harmonics, in contrast to typical in-amps whose CMRR falls off around Hz. These in-amps often need common-mode filters at the inputs to compensate for this shortcoming. The AD8 is able to reject CMRR over a greater frequency range, reducing the need for input common-mode filtering. A well-implemented layout helps to maintain the high CMRR over frequency of the AD8. Input source impedance and capacitance should be closely matched. In addition, source resistance and capacitance should be placed as close to the inputs as possible. Grounding The output voltage of the AD8 is developed with respect to the potential on the reference terminal. Care should be taken to tie to the appropriate local ground (see Figure 59). In mixed-signal environments, low level analog signals need to be isolated from the noisy digital environment. Many ADCs have separate analog and digital ground pins. Although it is convenient to tie both grounds to a single ground plane, the current traveling through the ground wires and PC board can cause a large error. Therefore, separate analog and digital ground returns should be used to minimize the current flow from sensitive points to the system ground Figure 57. Example Layout Top Layer of the AD8 Evaluation Board Figure 58. Example Layout Bottom Layer of the AD8 Evaluation Board Rev. B Page of 8
21 ERENCE TERMINAL The reference terminal,, is at one end of a kω resistor (see Figure 55). The output of the instrumentation amplifier is referenced to the voltage on the terminal; this is useful when the output signal needs to be offset to voltages other than common. For example, a voltage source can be tied to the pin to level-shift the output so that the AD8 can interface with an ADC. The allowable reference voltage range is a function of the gain, common-mode input, and supply voltages. The pin should not exceed either +VS or VS by more than.5 V. For best performance, especially in cases where the output is not measured with respect to the terminal, source impedance to the terminal should be kept low, because parasitic resistance can adversely affect CMRR and gain accuracy. POWER SUPPLY REGULATION AND BYPASSING The AD8 has high PSRR. However, for optimal performance, a stable dc voltage should be used to power the instrumentation amplifier. Noise on the supply pins can adversely affect performance. As in all linear circuits, bypass capacitors must be used to decouple the amplifier. A. μf capacitor should be placed close to each supply pin. A μf tantalum capacitor can be used further away from the part (see Figure 59). In most cases, it can be shared by other precision integrated circuits. +V S INPUT BIAS CURRENT RETURN PATH The AD8 input bias current is extremely small at less than pa. Nonetheless, the input bias current must have a return path to common. When the source, such as a transformer, cannot provide a return current path, one should be created (see Figure 6). f HIGH-PASS = πrc C C +V S TRANSFORMER R R AD8 +V S AD8 +IN IN AD8.µF µf V OUT LOAD.µF µf Figure 59. Supply Decoupling, and Output Referred to Ground INPUT PROTECTION AC-COUPLED Figure 6. Creating an IBIAS Path All terminals of the AD8 are protected against ESD. (ESD protection is guaranteed to 4 kv, human body model.) In addition, the input structure allows for dc overload conditions a diode drop above the positive supply and a diode drop below the negative supply. Voltages beyond a diode drop of the supplies cause the ESD diodes to conduct and enable current to flow through the diode. Therefore, an external resistor should be used in series with each of the inputs to limit current for voltages above +Vs. In either scenario, the AD8 safely handles a continuous 6 ma current at room temperature. For applications where the AD8 encounters extreme overload voltages, as in cardiac defibrillators, external series resistors and low leakage diode clamps, such as BAV99Ls, FJHs, or SP7s, should be used Rev. B Page of 8
22 RF INTERFERENCE RF rectification is often a problem in applications where there are large RF signals. The problem appears as a small dc offset voltage. The AD8 by its nature has a 5 pf gate capacitance, CG, at its inputs. Matched series resistors form a natural low-pass filter that reduces rectification at high frequency (see Figure 6). The relationship between external, matched series resistors and the internal gate capacitance is expressed as follows: FilterFreqDIFF πrc G R 4.kΩ R 4.kΩ C C C D C C nf nf nf.µf +IN AD8 µf V OUT IN.µF µf FilterFreq CM πrc G 5V Figure 6. RFI Suppression R R +IN IN.µF µf C G AD8 C G.µF µf V OUT 5V Figure 6. RFI Filtering Without External Capacitors To eliminate high frequency common-mode signals while using smaller source resistors, a low-pass RC network can be placed at the input of the instrumentation amplifier (see Figure 6). The filter limits the input signal bandwidth according to the following relationship: FilterFreqDIFF πr( CD CC C ) FilterFreq CM πr( CC C G Mismatched CC capacitors result in mismatched low-pass filters. The imbalance causes the AD8 to treat what would have been a common-mode signal as a differential signal. To reduce the effect of mismatched external CC capacitors, select a value of CD greater than times CC. This sets the differential filter frequency lower than the common-mode frequency. ) G COMMON-MODE INPUT VOLTAGE RANGE The common-mode input voltage range is a function of the input range and the outputs of Internal Amplifier A, Internal Amplifier A, and Internal Amplifier A3, the reference voltage, and the gain. Figure 7 to Figure 3 show common-mode voltage ranges for various supply voltages and gains. DRIVING AN ADC An instrumentation amplifier is often used in front of an ADC to provide CMRR and additional conditioning, such as a voltage level shift and gain (see Figure 63). In this example, a.7 nf capacitor and a kω resistor create an antialiasing filter for the AD7685. The.7 nf capacitor also serves to store and deliver the necessary charge to the switched capacitor input of the ADC. The kω series resistor reduces the burden of the.7 nf load from the amplifier. However, large source impedance in front of the ADC can degrade THD. The example shown in Figure 63 is for sub-6 khz applications. For higher bandwidth applications where THD is important, the series resistor needs to be small. At worst, a small series resistor can load the AD8, potentially causing the output to overshoot or ring. In such cases, a buffer amplifier, such as the AD865, should be used after the AD8 to drive the ADC. ±5mV µf.7kω.µf +IN IN AD8 +.5V kω.7nf AD7685 ADR435 Figure 63. Driving an ADC in a Low Frequency Application 4.7µF Rev. B Page of 8
23 APPLICATIONS INFORMATION AC-COUPLED INSTRUMENTATION AMPLIFIER Measuring small signals that are in the noise or offset of the amplifier can be a challenge. Figure 64 shows a circuit that can improve the resolution of small ac signals. The large gain reduces the referred input noise of the amplifier to 4 nv/ Hz. Therefore, smaller signals can be measured because the noise floor is lower. DC offsets that would have been gained by are eliminated from the AD8 output by the integrator feedback network. At low frequencies, the OP77 forces the AD8 output to V. Once a signal exceeds fhigh-pass, the AD8 outputs the amplified input signal..µf R 499Ω +IN IN +V S AD8 f HIGH-PASS = πrc C R 5.8kΩ DIFFERENTIAL OUTPUT In certain applications, it is necessary to create a differential signal. New high resolution ADCs often require a differential input. In other cases, transmission over a long distance can require differential processing for better immunity to interference. Figure 65 shows how to configure the AD8 to output a differential signal. An OP77 op amp is used to create a differential voltage. Errors from the op amp are common to both outputs and are thus common mode. Likewise, errors from using mismatched resistors cause a common-mode dc offset error. Such errors are rejected in differential signal processing by differential input ADCs or instrumentation amplifiers. When using this circuit to drive a differential ADC, V can be set using a resistor divider from the reference of the ADC to make the output ratiometric with the ADC as shown in Figure 66. µf +V S.µF.µF OP77 +V S.µF µf µf Figure 64. AC-Coupled Circuit V Rev. B Page 3 of 8
24 AMPLITUDE.µF 5V ±5V TIME +IN IN.µF AD8 4.99kΩ V OUT A=+V IN +V AMPLITUDE +5.V +.5V +V TIME µf 5V 4.99kΩ 5V.µF OP77.µF AMPLITUDE +5.V V +.5V.5V +V TIME Figure 65. Differential Output with Level Shift V OUT B= V IN +V µF ±5V TIME +IN IN.µF µf AD8 4.99kΩ 5V 4.99kΩ 5V.µF OP77 V.5V V OUT A=+V IN +V TO V TO ADC FROM ERENCE.µF 4.99kΩ 4.99kΩ nf FROM ERENCE +AIN AIN TO V TO ADC V OUT B= V IN +V Figure 66. Configuring the AD8 to Output A Ratiometric, Differential Signal Rev. B Page 4 of 8
25 ELECTROCARDIOGRAM SIGNAL CONDITIONING The AD8 makes an excellent input amplifier for next generation ECGs. Its small size, high CMRR over frequency, rail-to-rail output, and JFET inputs are well suited for this application. Potentials measured on the skin range from. mv to mv. The AD8 solves many of the typical challenges of measuring these body surface potentials. The high CMRR of the AD8 helps reject common-mode signals that come in the form of line noise or high frequency EMI from equipment in the operating room. Its rail-to-rail output offers a wide dynamic range allowing for higher gains than would be possible using other instrumentation amplifiers. JFET inputs offer a large input capacitance of 5 pf. A natural RC filter is formed reducing high frequency noise when series input resistors are used in front of the AD8 (see the RF Interference section). In addition, the AD8 JFET inputs have ultralow input bias current and no current noise, making it useful for ECG applications where there are often large impedances. The MSOP and the optimal pinout of the AD8 allow smaller footprints and more efficient layout, paving the way for next-generation portable ECGs. Figure 67 shows an example ECG schematic. Following the AD8 is a.33 Hz high-pass filter, formed by the 4.7 μf capacitor and the MΩ resistor, which removes the dc offset that develops between the electrodes. An additional gain of 5, provided by the AD868, makes use of the V to 5 V input range of the ADC. An active, fifth-order, low-pass Bessel filter removes signals greater than approximately 6 Hz. An OP77 buffers, inverts, and gains the common-mode voltage taken at the midpoint of the AD8 gain setting resistors. This rightleg drive circuit helps cancel common-mode signals by inverting the common-mode signal and driving it back into the body. A 499 kω series resistor at the output of the OP77 limits the current driven into the body. C A B 5kΩ.pF kω pf kω.pf 5V 4.9kΩ 4.9kΩ 5V AD8 INSTRUMENTATION AMPLIFIER G=+4 4.kΩ OP77 5V 5V OP AMPS.5V.8kΩ HIGH-PASS FILTER.33Hz 4.7µF pf.5v G= kΩ MΩ 4kΩ AD868.5V LOW-PASS FIFTH ORDER FILTER AT 57Hz 4kΩ 47nF 9.3kΩ AD kΩ 33nF AD868.5V 33nF.5kΩ 4.99kΩ 4.5kΩ 4.5kΩ 68nF AD868.5V nf 5Ω.7nF AD7685 ADC 4.7µF ERENCE ADR435 68pF.7kΩ 866kΩ 499kΩ OP77 5V Figure 67. Example ECG Schematic Rev. B Page 5 of 8
26 OUTLINE DIMENSIONS PIN IDENTIFIER.65 BSC COPLANARITY MAX 6 5 MAX.3.9 COMPLIANT TO JEDEC STANDARDS MO-87-AA Figure Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters B ORDERING GUIDE Model, Temperature Range 3 Package Description Package Option Branding AD8ARMZ 4 C to +85 C 8-Lead MSOP RM-8 H AD8ARMZ-RL 4 C to +85 C 8-Lead MSOP, 3" Tape and Reel RM-8 H AD8ARMZ-R7 4 C to +85 C 8-Lead MSOP, 7" Tape and Reel RM-8 H AD8BRMZ 4 C to +85 C 8-Lead MSOP RM-8 HP AD8BRMZ-RL 4 C to +85 C 8-Lead MSOP, 3" Tape and Reel RM-8 HP AD8BRMZ-R7 4 C to +85 C 8-Lead MSOP, 7" Tape and Reel RM-8 HP AD8WARMZ 4 C to +5 C 8-Lead MSOP RM-8 YD AD8WARMZ-RL 4 C to +5 C 8-Lead MSOP, 3" Tape and Reel RM-8 YD AD8WARMZ-R7 4 C to +5 C 8-Lead MSOP, 7" Tape and Reel RM-8 YD Z = RoHS Compliant Part. W = Qualified for Automotive Applications. 3 See the Typical Performance Characteristics section for expected operation from 85 C to 5 C. AUTOMOTIVE PRODUCTS The AD8W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. B Page 6 of 8
27 NOTES Rev. B Page 7 of 8
28 NOTES 6 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D /(B) Rev. B Page 8 of 8
Low Cost Instrumentation Amplifier AD622
Data Sheet FEATURES Easy to use Low cost solution Higher performance than two or three op amp design Unity gain with no external resistor Optional gains with one external resistor (Gain range: 2 to 000)
More informationRail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier AD8397 FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails
More informationHigh Voltage Current Shunt Monitor AD8212
High Voltage Current Shunt Monitor AD822 FEATURES Adjustable gain High common-mode voltage range 7 V to 65 V typical 7 V to >500 V with external pass transistor Current output Integrated 5 V series regulator
More informationAD8253. 10 MHz, 20 V/μs, G = 1, 10, 100, 1000 icmos Programmable Gain Instrumentation Amplifier. Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM
Data Sheet 1 MHz, 2 V/μs, G = 1, 1, 1, 1 icmos Programmable Gain Instrumentation Amplifier FEATURES Small package: 1-lead MSOP Programmable gains: 1, 1, 1, 1 Digital or pin-programmable gain setting Wide
More informationLow Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifiers AD8276/AD8277
Data Sheet Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifiers AD87/AD877 FEATURES Wide input range beyond supplies Rugged input overvoltage protection Low supply current: μa maximum
More informationPrecision Thermocouple Amplifiers with Cold Junction Compensation AD8494/AD8495/AD8496/AD8497
Precision Thermocouple Amplifiers with Cold Junction Compensation AD494/AD49/AD496/AD497 FEATURES Low cost and easy to use Pretrimmed for J or K type thermocouples Internal cold junction compensation High
More informationPrecision, Unity-Gain Differential Amplifier AMP03
a FEATURES High CMRR: db Typ Low Nonlinearity:.% Max Low Distortion:.% Typ Wide Bandwidth: MHz Typ Fast Slew Rate: 9.5 V/ s Typ Fast Settling (.%): s Typ Low Cost APPLICATIONS Summing Amplifiers Instrumentation
More informationHigh Speed, Low Cost, Triple Op Amp ADA4861-3
High Speed, Low Cost, Triple Op Amp ADA486-3 FEATURES High speed 73 MHz, 3 db bandwidth 625 V/μs slew rate 3 ns settling time to.5% Wide supply range: 5 V to 2 V Low power: 6 ma/amplifier. db flatness:
More informationHigh Common-Mode Rejection. Differential Line Receiver SSM2141. Fax: 781/461-3113 FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 00 db typ 60 Hz: 00 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.00% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More informationLow Cost, High Speed, Rail-to-Rail, Output Op Amps ADA4851-1/ADA4851-2/ADA4851-4
Low Cost, High Speed, Rail-to-Rail, Output Op Amps ADA485-/ADA485-/ADA485-4 FEATURES Qualified for automotive applications High speed 3 MHz, 3 db bandwidth 375 V/μs slew rate 55 ns settling time to.% Excellent
More informationFeatures. Ordering Information. * Underbar marking may not be to scale. Part Identification
MIC86 Teeny Ultra Low Power Op Amp General Description The MIC86 is a rail-to-rail output, input common-mode to ground, operational amplifier in Teeny SC7 packaging. The MIC86 provides 4kHz gain-bandwidth
More informationQuad Low Offset, Low Power Operational Amplifier OP400
Data Sheet FEATURES Low input offset voltage: 5 µv maximum Low offset voltage drift over 55 C to 25 C:.2 μv/ C maximum Low supply current (per amplifier): 725 µa maximum High open-loop gain: 5 V/mV minimum
More informationHigh Speed, Low Power Dual Op Amp AD827
a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential
More informationHigh Speed, Low Power Monolithic Op Amp AD847
a FEATURES Superior Performance High Unity Gain BW: MHz Low Supply Current:.3 ma High Slew Rate: 3 V/ s Excellent Video Specifications.% Differential Gain (NTSC and PAL).9 Differential Phase (NTSC and
More informationwww.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LF411 Low Offset, Low Drift JFET Input Operational Amplifier General Description
More informationLF442 Dual Low Power JFET Input Operational Amplifier
LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while
More informationPowerAmp Design. PowerAmp Design PAD135 COMPACT HIGH VOLATGE OP AMP
PowerAmp Design COMPACT HIGH VOLTAGE OP AMP Rev G KEY FEATURES LOW COST SMALL SIZE 40mm SQUARE HIGH VOLTAGE 200 VOLTS HIGH OUTPUT CURRENT 10A PEAK 40 WATT DISSIPATION CAPABILITY 200V/µS SLEW RATE APPLICATIONS
More informationWide Bandwidth, Fast Settling Difet OPERATIONAL AMPLIFIER
Wide Bandwidth, Fast Settling Difet OPERATIONAL AMPLIFIER FEATURES HIGH GAIN-BANDWIDTH: 35MHz LOW INPUT NOISE: 1nV/ Hz HIGH SLEW RATE: V/µs FAST SETTLING: 24ns to.1% FET INPUT: I B = 5pA max HIGH OUTPUT
More informationHA-5104/883. Low Noise, High Performance, Quad Operational Amplifier. Features. Description. Applications. Ordering Information. Pinout.
HA5104/883 April 2002 Features This Circuit is Processed in Accordance to MILSTD 883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Low Input Noise Voltage Density at 1kHz. 6nV/ Hz (Max)
More informationHigh Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator ADP3339
Data Sheet High Accuracy, Ultralow IQ,.5 A, anycap Low Dropout Regulator FEATURES FUNCTIONAL BLOCK DIAGRAM High accuracy over line and load: ±.9% at 5 C, ±.5% over temperature Ultralow dropout voltage:
More informationPIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages
DESCRIPTION The µa71 is a high performance operational amplifier with high open-loop gain, internal compensation, high common mode range and exceptional temperature stability. The µa71 is short-circuit-protected
More informationTL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
More informationTS321 Low Power Single Operational Amplifier
SOT-25 Pin Definition: 1. Input + 2. Ground 3. Input - 4. Output 5. Vcc General Description The TS321 brings performance and economy to low power systems. With high unity gain frequency and a guaranteed
More informationLF412 Low Offset Low Drift Dual JFET Input Operational Amplifier
LF412 Low Offset Low Drift Dual JFET Input Operational Amplifier General Description These devices are low cost high speed JFET input operational amplifiers with very low input offset voltage and guaranteed
More informationLM741. Single Operational Amplifier. Features. Description. Internal Block Diagram. www.fairchildsemi.com
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationHigh Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338 FEATURES High accuracy over line and load: ±.8% @ 25 C, ±1.4% over temperature Ultralow dropout voltage: 19 mv (typ) @ 1 A Requires
More informationDESCRIPTIO. LT1226 Low Noise Very High Speed Operational Amplifier
FEATRES Gain of Stable GHz Gain Bandwidth V/µs Slew Rate.6nV/ Hz Input Noise Voltage V/mV Minimum DC Gain, R L = Ω mv Maximum Input Offset Voltage ±V Minimum Output Swing into Ω ide Supply Range ±.V to
More informationDescription. 5k (10k) - + 5k (10k)
THAT Corporation Low Noise, High Performance Microphone Preamplifier IC FEATURES Excellent noise performance through the entire gain range Exceptionally low THD+N over the full audio bandwidth Low power
More informationLow Noise, High Speed Amplifier for 16-Bit Systems AD8021
Low Noise, High Speed Amplifier for -Bit Systems AD FEATURES Low noise. nv/ Hz input voltage noise. pa/ Hz input current noise Custom compensation Constant bandwidth from G = to G = High speed MHz (G =
More informationHigh Speed, Low Noise Video Op Amp AD829
Data Sheet FEATURES High speed MHz bandwidth, gain = V/µs slew rate 9 ns settling time to.% Ideal for video applications.% differential gain. differential phase Low noise.7 nv/ Hz input voltage noise.
More informationDescription. Output Stage. 5k (10k) - + 5k (10k)
THAT Corporation Low Noise, High Performance Audio Preamplifier IC FEATURES Low Noise: 1 nv/hz input noise (60dB gain) 34 nv/hz input noise (0dB gain) (1512) Low THD+N (full audio bandwidth): 0.0005% 40dB
More informationAdvanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
More informationLow Voltage Microphone Preamplifier with Variable Compression and Noise Gating SSM2167
Data Sheet Low Voltage Microphone Preamplifier with Variable Compression and Noise Gating SSM267 FEATURES PIN CONFIGURATION Complete microphone conditioner in a 0-lead package Single 3 V operation Low
More informationAP331A XX G - 7. Lead Free G : Green. Packaging (Note 2)
Features General Description Wide supply Voltage range: 2.0V to 36V Single or dual supplies: ±1.0V to ±18V Very low supply current drain (0.4mA) independent of supply voltage Low input biasing current:
More informationLow Noise, Matched Dual PNP Transistor MAT03
a FEATURES Dual Matched PNP Transistor Low Offset Voltage: 100 V Max Low Noise: 1 nv/ Hz @ 1 khz Max High Gain: 100 Min High Gain Bandwidth: 190 MHz Typ Tight Gain Matching: 3% Max Excellent Logarithmic
More informationTL082 Wide Bandwidth Dual JFET Input Operational Amplifier
TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost high speed dual JFET input operational amplifiers with an internally trimmed input offset voltage
More information15 MHz Rail-to-Rail Operational Amplifiers OP162/OP262/OP462
Data Sheet FEATURES Wide bandwidth: 5 MHz Low offset voltage: 35 µv max Low noise: 9.5 nv/ Hz @ khz Single-supply operation:.7 V to V Rail-to-rail output swing Low TCVOS: µv/ C typ High slew rate: 3 V/µs
More informationCMOS Switched-Capacitor Voltage Converters ADM660/ADM8660
CMOS Switched-Capacitor Voltage Converters ADM66/ADM866 FEATURES ADM66: Inverts or Doubles Input Supply Voltage ADM866: Inverts Input Supply Voltage ma Output Current Shutdown Function (ADM866) 2.2 F or
More informationFeatures. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND
DATASHEET IDT5P50901/2/3/4 Description The IDT5P50901/2/3/4 is a family of 1.8V low power, spread spectrum clock generators capable of reducing EMI radiation from an input clock. Spread spectrum technique
More informationCA3420. Features. 0.5MHz, Low Supply Voltage, Low Input Current BiMOS Operational Amplifier. Applications. Functional Diagram. Ordering Information
CA Data Sheet October, FN.9.MHz, Low Supply Voltage, Low Input Current BiMOS Operational Amplifier The CA is an integrated circuit operational amplifier that combines PMOS transistors and bipolar transistors
More informationLM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier General Description The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count
More informationAUDIO BALANCED LINE DRIVERS
DRV DRV DRV DRV DRV AUDIO BALAED LINE DRIVERS FEATURES BALAED OUTPUT LOW DISTORTION:.% at f = khz WIDE OUTPUT SWING: Vrms into Ω HIGH CAPACITIVE LOAD DRIVE HIGH SLEW RATE: V/µs WIDE SUPPLY RANGE: ±.V to
More information+5 V Powered RS-232/RS-422 Transceiver AD7306
a FEATURES RS- and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations APPLICATIONS
More informationLow-Cost, Micropower, SC70/SOT23-8, Microphone Preamplifiers with Complete Shutdown
9-9; Rev ; 4/ Low-Cost, Micropower, SC7/SOT23-8, Microphone General Description The are micropower op amps optimized for use as microphone preamplifiers. They provide the ideal combination of an optimized
More informationDUAL/QUAD LOW NOISE OPERATIONAL AMPLIFIERS
Order this document by MC3378/D The MC3378/9 series is a family of high quality monolithic amplifiers employing Bipolar technology with innovative high performance concepts for quality audio and data signal
More informationUse and Application of Output Limiting Amplifiers (HFA1115, HFA1130, HFA1135)
Use and Application of Output Limiting Amplifiers (HFA111, HFA110, HFA11) Application Note November 1996 AN96 Introduction Amplifiers with internal voltage clamps, also known as limiting amplifiers, have
More informationVoltage Output Temperature Sensor with Signal Conditioning AD22100
Voltage Output Temperature Sensor with Signal Conditioning AD22100 FEATURES 200 C temperature span Accuracy better than ±2% of full scale Linearity better than ±1% of full scale Temperature coefficient
More information160 MHz Rail-to-Rail Amplifier with Disable AD8041
16 MHz Rail-to-Rail Amplifier with Disable AD81 FEATURES Fully Specified for + V, +5 V, and 5 V Supplies Output Swings Rail to Rail Input Voltage Range Extends mv Below Ground No Phase Reversal with Inputs
More informationTSV6290, TSV6290A, TSV6291, TSV6291A
Micropower with high merit factor CMOS operational amplifiers Features Low supply voltage: 1.5 V 5.5 V Rail-to-rail input and output Low input offset voltage: 800 µv max (A version) Low power consumption:
More informationLM2902. Low-power quad operational amplifier. Features. Description
Low-power quad operational amplifier Datasheet production data Features Wide gain bandwidth: 1.3 MHz Input common-mode voltage range includes negative rail Large voltage gain: 100 db Very low supply current
More informationICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock
More informationLow Noise, Precision, High Speed Operational Amplifier (A VCL > 5) OP37
a FEATURES Low Noise, 80 nv p-p (0.1 Hz to 10 Hz) 3 nv/ Hz @ 1 khz Low Drift, 0.2 V/ C High Speed, 17 V/ s Slew Rate 63 MHz Gain Bandwidth Low Input Offset Voltage, 10 V Excellent CMRR, 126 db (Common-Voltage
More informationFeatures. Applications
LM555 Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More information1.5 Ω On Resistance, ±15 V/12 V/±5 V, icmos, Dual SPDT Switch ADG1436
.5 Ω On Resistance, ±5 V/2 V/±5 V, icmos, Dual SPDT Switch ADG436 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel LFCSP package:
More informationSupertex inc. HV256. 32-Channel High Voltage Amplifier Array HV256. Features. General Description. Applications. Typical Application Circuit
32-Channel High Voltage Amplifier Array Features 32 independent high voltage amplifiers 3V operating voltage 295V output voltage 2.2V/µs typical output slew rate Adjustable output current source limit
More informationCMOS 1.8 V to 5.5 V, 2.5 Ω SPDT Switch/2:1 Mux in Tiny SC70 Package ADG779
CMO 1.8 V to 5.5 V, 2.5 Ω PT witch/2:1 Mux in Tiny C70 Package AG779 FEATURE 1.8 V to 5.5 V single supply 2.5 Ω on resistance 0.75 Ω on-resistance flatness 3 db bandwidth >200 MHz Rail-to-rail operation
More informationUA741. General-purpose single operational amplifier. Features. Applications. Description. N DIP8 (plastic package)
General-purpose single operational amplifier Datasheet - production data N DIP8 (plastic package) D SO8 (plastic micropackage) Pin connections (top view) 1 - Offset null 1 2 - Inverting input 3 - Non-inverting
More informationIsolated AC Sine Wave Input 3B42 / 3B43 / 3B44 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated AC Sine Wave Input 3B42 / 3B43 / 3B44 FEATURES AC averaging technique used to rectify, amplify, and filter 50 Hz to 400 Hz sine-wave signals. Accepts inputs of between 20 mv to 550 V rms to give
More informationLMC6482 CMOS Dual Rail-To-Rail Input and Output Operational Amplifier
CMOS Dual Rail-To-Rail Input and Output Operational Amplifier General Description The LMC6482 provides a common-mode range that extends to both supply rails. This rail-to-rail performance combined with
More informationDual Precision, Low Power BiFET Op Amp AD648 CONNECTION DIAGRAMS
a FEATURES DC Performance 400 A max Quiescent Current 10 pa max Bias Current, Warmed Up (AD648C) 300 V max Offset Voltage (AD648C) 3 V/ C max Drift (AD648C) 2 V p-p Noise, 0.1 Hz to 10 Hz AC Performance
More informationTL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
More informationMIC2940A/2941A. Features. General Description. Applications. Pin Configuration. 1.2A Low-Dropout Voltage Regulator
MIC294A/2941A 1.2A Low-Dropout oltage Regulator General Description The MIC294A and MIC2941A are bulletproof efficient voltage regulators with very low dropout voltage (typically 4 at light loads and 35
More informationMUSES8920. High Quality Audio J-FET Input Dual Operational Amplifier - 1 -
MUSES89 High Quality Audio J-FET Input Dual Operational Amplifier GENERAL DESCRIPTION The MUSES89 is a high quality Audio J-FET input dual operational amplifier. This is a mass production model of MUSES
More informationLow Cost, Low Power, True RMS-to-DC Converter AD736
Low Cost, Low Power, True RMS-to-Donverter FEATURES Computes True rms value Average rectified value Absolute value Provides 00 mv full-scale input range (larger inputs with input attenuator) High input
More informationMC33079. Low noise quad operational amplifier. Features. Description
Low noise quad operational amplifier Datasheet production data Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion: 0.002% Large output voltage
More information3 V/5 V Low Power, Synchronous Voltage-to-Frequency Converter AD7740*
a FEATURES Synchronous Operation Full-Scale Frequency Set by External System Clock 8-Lead SOT-23 and 8-Lead MSOP Packages 3 V or 5 V Operation Low Power: 3 mw (Typ) Nominal Input Range: 0 to V REF True
More informationHigh-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information
General Description The MAX941/MAX94/ are single/dual/quad highspeed comparators optimized for systems powered from a 3V or 5V supply. These devices combine high speed, low power, and rail-to-rail inputs.
More information5.5 V Input, 300 ma, Low Quiescent Current, CMOS Linear Regulator ADP122/ADP123
Data Sheet 5.5 V Input, 3 ma, Low Quiescent Current, CMOS Linear Regulator ADP/ADP3 FEATURES Input voltage supply range:.3 V to 5.5 V 3 ma maximum output current Fixed and adjustable output voltage versions
More informationAD8601/AD8602/AD8604. Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers FEATURES PIN CONFIGURATIONS
Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers AD86/AD862/AD864 FEATURES Low offset voltage: 5 μv maximum Single-supply operation: 2.7 V to 5.5 V Low supply current:
More informationLM56 Dual Output Low Power Thermostat
Dual Output Low Power Thermostat General Description The LM56 is a precision low power thermostat. Two stable temperature trip points (V T1 and V T2 ) are generated by dividing down the LM56 1.250V bandgap
More informationLow-Power, Single-Supply, Wideband Operational Amplifier
OPA8 SBOS26F AUGUST 24 REVISED AUGUST 28 Low-Power, Single-Supply, Wideband Operational Amplifier FEATURES HIGH BANDWIDTH: 25MHz (G = +1) 11MHz (G = +2) LOW SUPPLY CURRENT:.9mA (V S = +5V) FLEXIBLE SUPPLY
More informationDual 20W Audio Power Amplifier with Mute and Standby Modes
LM1876 Overture Audio Power Amplifier Series Dual 20W Audio Power Amplifier with Mute and Standby Modes General Description The LM1876 is a stereo audio amplifier capable of delivering typically 20W per
More informationINDUSTRIAL VOLTAGE AMPLIFIER IC AM401 PRINCIPLE FUNCTION
PINCIPLE FUNCTION Amplification and conversion of differential signals referenced to ground to adjustable industrial voltages (0...Vcc-5V, e.g. 0...5/10V etc.) Variable current/voltage source and integrated
More informationLM2704 Micropower Step-up DC/DC Converter with 550mA Peak Current Limit
Micropower Step-up DC/DC Converter with 550mA Peak Current Limit General Description The LM2704 is a micropower step-up DC/DC in a small 5-lead SOT-23 package. A current limited, fixed off-time control
More informationLM118/LM218/LM318 Operational Amplifiers
LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They
More informationApplication of Rail-to-Rail Operational Amplifiers
Application Report SLOA039A - December 1999 Application of Rail-to-Rail Operational Amplifiers Andreas Hahn Mixed Signal Products ABSTRACT This application report assists design engineers to understand
More information1.0A LOW DROPOUT LINEAR REGULATOR
1.0A LOW DROPOUT LINEAR REGULATOR Description Pin Assignments The is a low dropout three-terminal regulator with 1.0A output current ability, and the dropout voltage is specified at typical 1.1V at 1.0A
More informationLM833 LOW NOISE DUAL OPERATIONAL AMPLIFIER
LOW NOISE DUAL OPERATIONAL AMPLIFIER LOW VOLTAGE NOISE: 4.5nV/ Hz HIGH GAIN BANDWIDTH PRODUCT: 15MHz HIGH SLEW RATE: 7V/µs LOW DISTORTION:.2% EXCELLENT FREQUENCY STABILITY ESD PROTECTION 2kV DESCRIPTION
More informationObsolete Product(s) - Obsolete Product(s)
32 W hi-fi audio power amplifier Features High output power (50 W music power IEC 268.3 rules) High operating supply voltage (50 V) Single or split supply operations Very low distortion Short-circuit protection
More informationSPREAD SPECTRUM CLOCK GENERATOR. Features
DATASHEET ICS7152 Description The ICS7152-01, -02, -11, and -12 are clock generators for EMI (Electro Magnetic Interference) reduction (see below for frequency ranges and multiplier ratios). Spectral peaks
More informationFUNCTIONAL BLOCK DIAGRAM 3V TO 5V (ADC REF) ST2 ST1 TEMP V RATIO SELF-TEST @ 25 C MECHANICAL SENSOR AC AMP CHARGE PUMP AND VOLTAGE REGULATOR
Data Sheet FEATURES Complete rate gyroscope on a single chip Z-axis (yaw rate) response 2 /hour bias stability.2 / second angle random walk High vibration rejection over a wide frequency 1, g powered shock
More informationINTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
More informationLM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators
Low Power Low Offset Voltage Quad Comparators General Description The LM139 series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mv max for
More informationQuad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard
More informationSmall, Low Power, 3-Axis ±3 g Accelerometer ADXL337
Small, Low Power, 3-Axis ±3 g Accelerometer ADXL337 FEATURES 3-axis sensing Small, low profile package 3 mm 3 mm 1.4 mm LFCSP Low power: 3 μa (typical) Single-supply operation: 1.8 V to 3.6 V 1, g shock
More informationCMOS 5 V/+5 V 4 Single SPDT Switches ADG619/ADG620
a FEATURE (Max) On Resistance. (Max) On Resistance Flatness.7 V to 5.5 ingle upply.7 V to 5.5 V ual upply Rail-to-Rail Operation -Lead OT-3 Package, -Lead MOP Package Typical Power Consumption (
More informationLM380 Audio Power Amplifier
LM380 Audio Power Amplifier General Description The LM380 is a power audio amplifier for consumer application. In order to hold system cost to a minimum, gain is internally fixed at 34 db. A unique input
More informationCMOS 1.8 V to 5.5 V, 2.5 Ω 2:1 Mux/SPDT Switch in SOT-23 ADG719
CMOS 1.8 V to 5.5 V, 2.5 Ω 2:1 Mux/SPT Switch in SOT-23 AG719 FEATURES 1.8 V to 5.5 V single supply 4 Ω (max) on resistance 0.75 Ω (typ) on resistance flatness 3 db bandwidth > 200 MHz Rail-to-rail operation
More informationNCS7101, NCV7101. 1.8 Volt Rail-to-Rail Operational Amplifier LOW VOLTAGE RAIL TO RAIL OPERATIONAL AMPLIFIER
NCS711, NCV711 1.8 Volt RailtoRail Operational Amplifier The NCS711 operational amplifier provides railtorail operation on both the input and output. The output can swing within 5 mv of each rail. This
More informationNTE923 & NTE923D Integrated Circuit Precision Voltage Regulator
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator Description: The NTE923 and NTE923D are voltage regulators designed primarily for series regulator applications. By themselves, these devices
More informationDESCRIPTION FEATURES TYPICAL APPLICATION. LT1097 Low Cost, Low Power Precision Op Amp APPLICATIONS
LT97 Low Cost, Low Power Precision Op Amp FEATRES Offset Voltage µv Max Offset Voltage Drift µv/ C Max Bias Current pa Max Offset Current pa Max Bias and Offset Current Drift pa/ C Max Supply Current µa
More informationDigital to Analog Converter. Raghu Tumati
Digital to Analog Converter Raghu Tumati May 11, 2006 Contents 1) Introduction............................... 3 2) DAC types................................... 4 3) DAC Presented.............................
More informationLM1084 5A Low Dropout Positive Regulators
5A Low Dropout Positive Regulators General Description The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5 at 5A of load current. It has the same pin-out as
More informationAS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
More informationTRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features
DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency
More informationProgrammable-Gain Transimpedance Amplifiers Maximize Dynamic Range in Spectroscopy Systems
Programmable-Gain Transimpedance Amplifiers Maximize Dynamic Range in Spectroscopy Systems PHOTODIODE VOLTAGE SHORT-CIRCUIT PHOTODIODE SHORT- CIRCUIT VOLTAGE 0mV DARK ark By Luis Orozco Introduction Precision
More informationLM138 LM338 5-Amp Adjustable Regulators
LM138 LM338 5-Amp Adjustable Regulators General Description The LM138 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5A over a 1 2V to 32V output range
More informationNE592 Video Amplifier
Video Amplifier The NE is a monolithic, two-stage, differential output, wideband video amplifier. It offers fixed gains of and without external components and adjustable gains from to with one external
More informationPush-Pull FET Driver with Integrated Oscillator and Clock Output
19-3662; Rev 1; 5/7 Push-Pull FET Driver with Integrated Oscillator General Description The is a +4.5V to +15V push-pull, current-fed topology driver subsystem with an integrated oscillator for use in
More information