Mineral fibreglass insulation

Transcription

1 Isover MULTIMAX 30 Specification code: MW - EN T5 - MU1 - WS - WL(P) - AF r 5 TeChNICaL SPeCIFICaTION Insulating slabs made of Isover fibreglass wool. The production method is based on the fibering of glass melt and other additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably against the weather effects (outer cassette sheathing, diffusion and vapour-proof foil). application A glass mineral wool slabs, Isover MULTIMAX are suitable for insulation of the outer walls of ventilated facade systems and are to be inserted into the grid under the cladding, or mechanically bonded into the multilayer masonry. The slabs can be mechanically bond using the clamps for soft MW insulations. Insulating slabs are not glued to the surface. When the material is used to insulate ceilings, it is also necessary to use metal dowel pins with respect to fire security that cannot be positioned at the edge of the slab. Especially the energy saving insulation type, λ D = 0,030 W.m -1.K -1. PaCkaGING, TRaNSPORT, WaRehOUSING A glass mineral wool slabs, Isover MULTIMAX, are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. BeNeFITS dimensions and PaCkaGING Product (mm) Dimensions (mm) Per package (m2) MPS (m 2 ) TeChNICaL PaRameTeRS resistance R D (m 2. K. W -1 ) Isover MULTIMAX x Isover MULTIMAX x Isover MULTIMAX x Isover MULTIMAX x tolerance classification T5 complies with allowed tolerance according to EN 13162: -1% or - 1 mm and + 3 mm, while the higher numerical value prevails. conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Specific load value kn. m EN , EN 1990 Specific resistance against air flow AF r kpa. s. m EN Water vapour penetrability Vapour resistance coefficient (μ) MU EN ReLaTed documents EC compliance certificate 1486-CPD-0254

2 Isover UNIROL PROFI Specification code: MW - EN T2 - MU1 - AF 5 r Rolled insulation mats made of Isover fibreglass wool are covered with hydrophobic fibres on the entire surface. The production method is based on the fibering of glass melt and other additives and ingredients. The mineral fibres produced are processed into the final mat shape on the production line. The insulation in the construction should be protected (vapour-proof foil, suitable protection against dust setting in case of loosely laid insulation, additional construction layers). The insulation is not harmful to the environment or public health, it is resistant to moulds, fungi and wood-destroying insects. The fibreglass insulation mats with excellent heat-insulating properties are used as thermal and acoustic insulation of sloping roofs and ceilings. Superior energy saving type of insulation, λ D = W.m -1.K -1. The Isover rolls are strongly compressed within the package and wrapped with PE foil (1 MPS = 12 Rolls, volume 4,09 m 3 ). After unpacking, the rolls quickly acquire full thickness. Compressing makes manipulation easier and saves space in warehouses, during transport and on the construction site. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Product (mm) Dimensions (mm) Per package (m 2 ) MPS (m 2 ) conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Maximum temperature for use C 200 Sound absorption coefficient α Hz resistance R D (m 2.K.W -1 ) Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x Isover UNIROL PROFI x tolerance classification T2 complies with the allowed tolerance according to EN 13162: -5% or -5 mm, while the higher numerical value prevails, and + 15% or + 15 mm where the lower tolerance numerical value is decisive. For calculation is possible use same value as for DOMO. Specific resistance against air flow AF r kpa. s. m -2 5 EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN EG compliance certificate 1486-CPD-0254

3 Isover Multi-Komfort Passivhaus Klemmfilz Rolled insulation mats made of Isover fibreglass wool are covered with hydrophobic fibres on the entire surface. The production method is based on the fibering of glass melt and other additives and ingredients. The mineral fibres produced are processed into the final mat shape on the production line. The insulation in the construction should be protected (vapour-proof foil, suitable protection against dust setting in case of loosely laid insulation, additional construction layers). Isover MK-KF rolls are suitable for any thermal, acoustic, no-load insulation. Preferred application is for lattice works at multistoried or single storied buildings and their hanging false ceilings. Also everywhere where is recommended high thickens of thermal insulation to reach passive house level (ideal Multi-Comfort house level). conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Specification code: MW - EN T2 - MU1 - AF r5 The Isover MK-KF rolls are strongly compressed within the package and wrapped with PE foil. They come in MPS packs (1MPS = 18 rolls, volume 3,67 m 3 ). After unpacking, the rolls quickly acquire full thickness. Compressing makes manipulation easier and saves space in warehouses, during transport and on the construction site. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Specific resistance against air flow AF r kpa. s. m -2 5 EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN Product (mm) Dimensions (mm) Per package (m 2 ) MPS (m 2 ) resistance R D (m 2.K.W -1 ) Isover MK-KF x Isover MK-KF x Isover MK-KF x Isover MK-KF x Isover MK-KF x Isover MK-KF x Isover MK-KF * 3500 x Isover MK-KF * 3500 x Isover MK-KF * 3500 x Isover MK-KF * 3000 x tolerance classification T2 complies with the allowed tolerance according to EN 13162: -5% or -5 mm, while the higher numerical value prevails, and + 15% or + 15 mm where the lower tolerance numerical value is decisive. EG compliance certificate 1139-CPD-0735/09

4 Isover UNIROL-PLUS Specification code: MW - EN T2 - MU1 Rolled insulation mats made of Isover fibreglass wool are covered with hydrophobic fibres on the entire surface. The production method is based on the fibering of glass melt and other additives and ingredients. The mineral fibres produced are processed into the final mat shape on the production line. The insulation in the construction should be protected (vapour-proof foil, suitable protection against dust setting in case of loosely laid insulation, additional construction layers). The Isover UNIROL-PLUS rolls are strongly compressed within the package and wrapped with PE foil. They come in MPS packs (1MPS = 24 rolls for thicknesses mm and 12 rolls for thicknesses 180 and 200 mm, volume 4,09 m 3 ). After unpacking, the rolls quickly acquire full thickness. Compressing makes manipulation easier and saves space in warehouses, during transport and on the construction site. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Isover UNIROL-PLUS rolls are suitable for unloaded thermal and acoustic insulation of pitch roofs especially with insertion between rafters and additional frame as well, into partition walls, wood ceilings insulations, false ceilings, and cavities. Technické parametry conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Ostatní vlastnosti Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN Product (mm) Dimensions (mm) Per package (m 2 ) MPS (m 2 ) resistance R D (m 2.K.W -1 ) Isover UNIROL-PLUS x Isover UNIROL-PLUS x Isover UNIROL-PLUS x Isover UNIROL-PLUS x Isover UNIROL-PLUS x Isover UNIROL-PLUS x Isover UNIROL-PLUS x tolerance classification T2 complies with the allowed tolerance according to EN 13162: -5% or -5 mm, while the higher numerical value prevails, and + 15% or + 15 mm where the lower tolerance numerical value is decisive. EG compliance certificate 1486-CPD-0253

5 Isover UNI Mineral insulation from stone wool Specification code: MW - EN T4 - DS(T+) - MU1 Insulating slabs made of Isover mineral wool. The production is based on defibring method of the minerals composition melt and additional additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably against the weather effects (outer cassette sheathing, diffusion and vapour-proof foil). Isover UNI slabs are suitable for unloaded insulations of the outer walls (ventilated facades under the cladding with insulant inserted into cassettes or frames), insulation of the pitch roofs, ceilings, false ceilings and other light sandwich constructions. The material is suitable for fire protection partition walls where the density 40 kg.m -3 is required. EC compliance certificate 1390-CPD-0305/11/P Isover UNI insulation slabs are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. Product (mm) Dimensions (mm) Per package (m 2 ) Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x Isover UNI x tolerance classification T4 complies with allowed tolerance according to EN 13162: -3% or - 3 mm, while the higher numerical value prevails and + 5% or + 5 mm where the lower tolerance numerical value is predominant. conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Specific load value kn. m EN , EN 1990 Dimensional stability at temperature (70 ± 2) C DS (T+) % 1 EN 1604 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz The practical sound absorption coefficient α p according to EN ISO 354 and EN ISO Definition of single number value according to EN ISO mm mm mm mm Single number value - α w α stř NCR 40 mm 0.70 (MH) mm mm mm Moisture resistance factor (µ) MU - 1 EN Specific resistance against air flow AF r kpa. s. m EN 29053

6 Isover ORSIK Mineral insulation from stone wool Specification code: MW - EN T2 - MU1 Insulating slabs made of Isover mineral wool. The production is based on defibring method of the minerals composition melt and additional additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably against the weather effects, increased relative inner humidity and condensate (diffusion and vapour-proof foil). Isover ORSIK slabs are suitable for unloaded thermal, acoustic and fire insulation of pitch roofs especially with insertion between rafters and additional frame as well, into partition walls, wood ceilings insulations, false ceilings, and cavities. Isover ORSIK insulation slabs are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. Product (mm) Dimensions (mm) Per package (m 2 ) Isover ORSIK x Isover ORSIK x Isover ORSIK x Isover ORSIK x Isover ORSIK * 1200 x Isover ORSIK * 1200 x Isover ORSIK * 1200 x Isover ORSIK * 1200 x Isover ORSIK * 1200 x Isover ORSIK * 1200 x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5 mm, while the higher numerical value prevails and + 15% or + 15 mm where the lower tolerance numerical value is predominant. * Compressed packaging conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Tensile strength in slab level (σ t ) kpa 1 EN 1608 Specific load value kn. m -3 0,30 EN , EN 1990 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz The practical sound absorption coefficient α p according to EN ISO 354 and EN ISO Definition of single number value according to EN ISO mm mm mm mm Single number value - α w α stř NCR 40 mm 0.70 (H) mm mm mm Moisture resistance factor (μ) MU - 1 EN EC compliance certificate 1390-CPD-0305/11/P

7 Isover DOMO COMFORT Specification code: MW - EN T2 - MU1 - AF r 5 Rolled insulation mats made of Isover fibreglass wool 1200 mm width with special coated surface for easy workability. The wool are covered with hydrophobic fibres on the entire surface. The production method is based on the fibering of glass melt and other additives and ingredients. The mineral fibres produced are processed into the final mat shape on the production line. The insulation in the construction should be protected (vapour-proof foil, suitable protection against dust setting in case of loosely laid insulation, additional construction layers). The insulation is not harmful to the environment or public health, it is resistant to moulds, fungi and wood-destroying insects. Isover DOMO COMFORT rolls are suitable for any thermal, acoustic, no-load insulation for hanging false ceilings, cavity insulation (increase in acoustic insulation), and non-running roof constructions. The Isover DOMO COMFORT rolls are packaged into PE foil. They come in MPS packs (1MPS = 24 rolls, volume 4.09 m 3 ). Loose packages can be supplied after an agreement with the manufacturer. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Product (mm) Dimensions (mm) Per package (m 2 ) MPS (m 2 ) resistance R D (m 2.K.W -1 ) DOMO COMFORT x DOMO COMFORT x DOMO COMFORT x DOMO COMFORT x DOMO COMFORT x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5% mm, while the higher numerical value prevails and + 15mm or + mm where the lower tolerance numerical value is predominant. conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Reaction to fire class - A2-s1,d0 EN Specific resistance against air flow AF r kpa. s. m -3 5 EN Vapour resistance coefficient (μ) MU - 1 EN EC compliance certificate 1486-CPD-0254

8 Isover DOMO Specification code: MW - EN T1 - MU1 - AF r 5 Insulation rolls made of Isover fibreglass wool. The production is based on defibration of melt of glass and other additives and ingredients. Produced mineral fibres are then shaped into rolls on the production line. Fibres are made water-repellent on their entire surface. Insulation in construction have to be protected suitably (steam protection foil, suitable protection against dust settling in loosely laid constructions, other construction layers). Isover DOMO rolls are suitable for any thermal, acoustic, no-load insulation for hanging false ceilings, cavity insulation (increase in acoustic insulation), and non-running roof constructions. conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Frekvence Hz DOMO Directly on the wall Acoustic absorption coefficient α DOMO mm The Isover DOMO rolls are packaged into PE foil. They come in MPS packs (1MPS = 24 rolls, volume 4,09 m 3 ). Loose packages can be supplied after an agreement with the manufacturer. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. DOMO DOMO Specific resistance against air flow AF r kpa. s. m -2 5 EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN Product (mm) Dimensions (mm) Per package (m 2 ) MPS (m 2 ) resistance R D (m 2.K.W -1 ) Isover DOMO TWIN 10/5 100/50 2 x 7500 x Isover DOMO TWIN 12/6 120/60 2 x 6000 x Isover DOMO x Isover DOMO x Isover DOMO x Isover DOMO x Isover DOMO x Isover DOMO x Isover DOMO x tolerance classification T1 complies with the allowed tolerance according to EN 13162: -5% or -5 mm, while the higher numerical value prevails, and higher thickness is possible. Note: Name TWIN 10/5 - in the packing are 2 rolls, same thickness 50 mm, applicable as one roll 100 mm. EG compliance certificate 1486-CPD-0254

9 Isover ORSTROP Mineral insulation from stone wool Specification code: MW - EN T2 - MU1 Insulating slabs made of Isover mineral wool. The production is based on defibring method of the minerals composition melt and additional additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably against inner humidity (vapour-proof foil, suitable protection against dust setting, false ceilings sheathing, and additional construction layers). Isover ORSTROP slabs are suitable for unloaded thermal, acoustic and fire insulation of ceilings (between joists), unused attics, false ceilings and cavities. EC compliance certificate 1390-CPD-0305/11/P Isover ORSTROP insulation slabs are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. Product (mm) Dimensions (mm) Per package (m 2 ) Isover ORSTROP x Isover ORSTROP x Isover ORSTROP x Isover ORSTROP x Isover ORSTROP * 1200 x Isover ORSTROP * 1200 x Isover ORSTROP * 1200 x Isover ORSTROP * 1200 x Isover ORSTROP * 1200 x Isover ORSTROP * 1200 x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5% mm, while the higher numerical value prevails and + 15mm or + mm where the lower tolerance numerical value is predominant. * Compressed packaging conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Specific load value kn. m EN , EN 1990 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz Acoustic absorption coefficient 40 mm α for perpendicular impact of 60 mm acoustic waves (-) according to 80 mm ISO mm mm mm 0.55 Mean acoustic absorption 60 mm 0.68 coefficient in the band of mm 0.88 ISO Hz α stř 120 mm mm 0.96 Moisture resistance factor (µ) MU - 1 EN 12086

10 Isover AKU Mineral insulation from stone wool Specification code: MW - EN T4 - DS(T+) - MU1 Insulating slabs made of Isover mineral wool. The production is based on defibring method of the minerals composition melt and additional additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably against the weather effects (outer cassette sheathing, diffusion and vapour-proof foil). Isover UNI slabs are suitable for plasterboard wall systems with 625 mm spacing as an acoustic and thermal insulation. The material is suitable for fire protection partition walls where the density 40 kg.m -3 is required. EC compliance certificate 1390-CPD-0305/11/P Isover UNI insulation slabs are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. Product (mm) Dimensions (mm) Per package (m 2 ) Isover AKU x Isover AKU x Isover AKU x Isover AKU x Isover AKU x tolerance classification T4 complies with allowed tolerance according to EN 13162: -3% or - 3 mm, while the higher numerical value prevails and + 5% or + 5 mm where the lower tolerance numerical value is predominant. conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Dimensional stability at temperature (70 ± 2) C DS (T+) % 1 EN 1604 Specific load value kn. m EN , EN 1990 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz The practical sound absorption coefficient α p according to EN ISO 354 and EN ISO Definition of single number value according to EN ISO mm mm mm mm Single number value - α w α stř NCR 40 mm 0.70 (MH) mm mm mm Other properties Specific resistance against air flow AF r kpa. s. m EN Moisture resistance factor (µ) MU - 1 EN 12086

11 Isover PIANO Specification code: MW - EN T2 - MU1 - AF r 5 Insulation rolls made of Isover fibreglass wool. The production is based on defibration of melt of glass and other additives and ingredients. Produced mineral fibres are then shaped into rolls on the production line. Fibres are made water-repellent on their entire surface. Rolls in construction have to be protected suitably (steam protection foil, partition wall lining, other layers of construction). ISOVER PIANO rolls are suitable for thermal, acoustic, no-load insulation which are a part of light construction with metal reinforcement. In residential or administrative buildings, attics, hotels, hospitals, and industry premises, the PIANO rolls increase total acoustic absorption of construction and therefore acoustic insulation capacity (improvement in sound reduction of up to 18dB, according to solution for side ways noise travel and the number of holes in the construction), especially if the entire cavity is filled (5-7 db improvement in sound reduction from cavity only half filled). The improvement in sound reduction depends on how side ways noise travel is limited, i.e. how the carrying frame of partition walls is insulated from the floor, ceiling, and walls with a flexible insulation tape. EG compliance certificate 1139-CPD-0170/02 Product (mm) Dimensions (mm) Packaging (m 2 ) MPS (m 2 ) The Isover PIANO rolls are packaged into PE foil. They come in MPS packs (1MPS = 24 rolls, volume 4.09 m 3 ). Loose packages can be supplied after an agreement with the manufacturer. Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. resistance R D (m 2.K.W -1 ) Isover PIANO TWIN 8/ x x Isover PIANO TWIN 10/ x x Isover PIANO TWIN 12/ x x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5mm, while the higher numerical value prevails and + 15% or +15 mm where the lower tolerance numerical value is predominant. Note: Name TWIN 10/5 - in the packing are 2 rolls, same thickness 50 mm, applicable as one roll 100 mm. Parameter Jednotka Hodnota Norma conductivity coefficient λ D W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Specific load value kn. m EN EN 1990 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz The practical sound absorption coefficient α p according to EN ISO 354 and EN ISO Definition of single number value according to EN ISO mm mm mm mm Single number value - α w α stř NCR 40 mm 0.75 (H) mm mm mm Specific resistance against air flow AF r kpa. s. m -2 5 EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN 12086

12 Isover ROLLINO Specification code: MW - EN T2 - MU1 - AF r 5 Insulation rolls made of Isover fibreglass wool. The production is based on defibration of melt of glass and other additives and ingredients. Produced mineral fibres are then shaped into rolls on the production line. Fibres are made water-repellent on their entire surface. Rolls in construction have to be protected suitably (steam protection foil, diffusion foil, suitable protection from dust settling, lining of false ceilings, sheathing of facades, other layers of construction). Isover ROLLINO slabs in a roll are suitable for thermal, acoustic, no-load insulation in attic apartment constructions, between rafters and stretchers, into ceilings, hanging false ceilings, for insulation of partition walls, cavities and ventilated facades with a frame and two storeys maximum, into assembled floors with posts. Isover MERINO slabs have dimensions of 625 x 1200 mm, are flexible, have stable form, and are applied on paper base. Isover ROLLINO is then rolled together with the paper base which has to be removed prior use. EG compliance certificate 1139-CPD-0735/09 The Isover ROLLINO slabs are packaged with the paper base into 1200mm rolls wrapped with PE foil. They are compressed within the package which makes manipulation easier and saves space in warehouses, during transport and on the construction site. Compared to MERINO, the space savings are up to three times higher. After unpacking, the slabs quickly acquire full thickness. The rolls come in MPS packs (1MPS = 18 rolls, volume 4,09 m 3 ). Rolls have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Product (mm) Dimensions (mm) Packaging (m 2 ) Packaging (m 3 ) MPS (m 2 ) Isover ROLLINO x Isover ROLLINO x Isover ROLLINO x Isover ROLLINO x Isover ROLLINO x Isover ROLLINO x Isover ROLLINO x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5mm, while the higher numerical value prevails and + 15% or +15 mm where the lower tolerance numerical value is predominant. Condition set for declared values I(10 C) and (u dry ) - - ČSN EN ISO conductivity coefficient λ D W. m -1. K ČSN EN Specific load value kn. m ČSN EN ČSN EN 1990 Reaction to fire class - A1 ČSN EN Frequency Hz ROLLINO 2-0,10 0,35 0,60 0,75 0,90 0,90 ROLLINO 5-0,25 0,60 0,90 1,00 1,00 1,00 60 mm Acoustic absorption coefficient α ROLLINO 8-0,45 0,75 1,00 1,00 1,00 1,00 ROLLINO 2-0,20 0,55 0,85 0,85 0,90 0,90 ROLLINO 5-0,40 0,75 1,00 1,00 1,00 1, mm ROLLINO 8-0,65 1,00 1,00 1,00 1,00 1,00 Specific resistance against air flow AF r kpa. s. m -2 5 ČSN EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 ČSN EN 12086

13 Isover MERINO Specification code: MW - EN T2 - MU1 - AF r 5 Insulation slabs made of Isover fibreglass wool. The production is based on defibration of melt of glass and other additives and ingredients. Produced mineral fibres are then shaped into slabs on the production line. Fibres are made water-repellent on their entire surface. Slabs in construction have to be protected suitably (steam protection foil, protection from dust settling, other layers of construction). Isover MERINO slabs are flexible and have stable shape but cannot be bear load. They are suitable for any thermal, acoustic, no-load insulation, especially for double construction, ceiling fillings, hanging false ceilings, and cavities (improving the acoustic absorption of the construction, assembled floors with posts), for ventilated facades with frame insulation (maximum two storeys, using timber studs with 300 mm clearance). EG compliance certificate 1486-CPD-0254 Isover MERINO slabs are packaged into PE foil. They come in MPS packs (1MPS = 12 packages). Loose packages can be supplied after an agreement with the manufacturer. Slabs have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Product (mm) Dimensions (mm) Packaging (m 2 ) Packaging (m 3 ) MPS (m 2 ) Isover MERINO x Isover MERINO x Isover MERINO x Isover MERINO x Isover MERINO x Isover MERINO x Isover MERINO x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5 mm, while the higher numerical value prevails and + 15% or +15 mm where the lower tolerance numerical value is predominant. Condition set for declared values I(10 C) and (u dry ) - - ČSN EN ISO conductivity coefficient λ D W. m -1. K ČSN EN Specific load value kn. m ČSN EN ČSN EN 1990 Reaction to fire class - A1 ČSN EN Frequency Hz MERINO 2-0,10 0,35 0,60 0,75 0,90 0,90 MERINO 5-0,25 0,60 0,90 1,00 1,00 1,00 60 mm Acoustic absorption coefficient α MERINO 8-0,45 0,75 1,00 1,00 1,00 1,00 MERINO 2-0,20 0,55 0,85 0,85 0,90 0,90 MERINO 5-0,40 0,75 1,00 1,00 1,00 1, mm MERINO 8-0,65 1,00 1,00 1,00 1,00 1,00 Specific resistance against air flow AF r kpa. s. m -2 5 ČSN EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 ČSN EN 12086

14 Isover ORSET Mineral insulation from stone wool Specification code: MW - EN T2 - MU1 Insulating slabs made of Isover mineral wool. The production is based on defibring method of the minerals composition melt and additional additives and ingredients. The mineral fibres produced are processed into the final slab shape on the production line. The entire fibre surface is hydrophobic. The slabs in the construction should be protected suitably (diffusion and vapour-proof foil against the weather effects, increased inner humidity, and outer partition wall sheathing). Isover ORSET slabs are suitable especially for unloaded thermal, acoustic and fire insulation of partition walls and other constructions of slanting roofs with insertion between rafters with clearance up to 1m, under additional frames of false ceilings (625mm), ceilings insulation, false ceilings, and cavities. EC compliance certificate 1390-CPD-0305/11/P Isover ORSET insulation slabs are packed into the PE foil with package height up to 0.5 m. The slabs have to be transported in covered vehicles under conditions preventing their wetting or other degradation. They should be stored flat in sheltered space to maximum layer height of 2 m. Product (mm) Dimensions (mm) Per package (m 2 ) Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x Isover ORSET x tolerance classification T2 complies with allowed tolerance according to EN 13162: - 5% or - 5% mm, while the higher numerical value prevails and + 15mm or + mm where the lower tolerance numerical value is predominant. Parameter Jednotka Hodnota Norma Soubor podmínek pro deklarované hodnoty I(10 C) a (u dry ) - - EN ISO Condition set for declared values I(10 C) and (u dry ) W. m -1. K EN Specific heat capacity c d J. kg -1. K ČSN Specific load value kn. m EN EN 1990 Melting temperature t t C 1000 DIN 4102 part 17 Frequency Hz The practical sound absorption coefficient α p according to EN ISO 354 and EN ISO Definition of single number value according to EN ISO mm mm mm mm Single number value - α w α stř NCR 40 mm 0.70 (H) mm mm mm Moisture resistace factor (µ) MU - 1 EN 12086

15 AKUSTIK PLATTE Specification code: MW EN T4 - MU1 - AF r 5 Insulation slabs made of Isover fibreglass wool. The production is based on defibration of melt of glass and other additives and ingredients. Produced mineral fibres are then shaped into slabs on the production line. Fibres are made water-repellent on their entire surface. Slabs in construction have to be protected suitably (covered with perforated material, other layers of construction). Isover AKUSTIK PLATTE slabs are suitable for any thermal, acoustic, no-load insulation. Black glass non-woven fabric is attached to one side. The slabs are used especially as absorbing insertion in lining elements for acoustic walls, ceilings, false ceilings, and thermal and acoustic insulation of air-conditioning devices. They are suitable for airflow not exceeding 30m/s. Fibers are made water-repellent on their entire surface. Isover AKUSTIK PLATTE slabs are packaged into PE foil. Slabs have to be transported in covered vehicles under conditions preventing them from getting wet or being degraded. They are stored in covered spaces. Product (mm) Dimensions (mm) Packaging (m 2 ) AKUSTIK PLATTE x AKUSTIK PLATTE x AKUSTIK PLATTE x AKUSTIK PLATTE x tolerance classification T4 complies with allowed tolerance according to EN 13162: -3% or - 3 mm, while the higher numerical value prevails and + 5% or + 5 mm where the lower tolerance numerical value is predominant. conductivity coefficient λ D W. m -1. K EN Specific load value kn. m EN , EN 1990 Reaction to fire class - A2 - s1, d0 EN Frequency Hz AKUSTIK PLATTE directly on the wall AKUSTIK PLATTE Acoustic absorption coefficient α 60 mm AKUSTIK PLATTE mm AKUSTIK PLATTE mm AKUSTIK PLATTE Specific resistance against air flow AF r kpa. s. m -2 5 EN Water vapour penetrability Vapour resistance coefficient (μ) MU - 1 EN EC certificate 1139-CPD-0735/09