4000 Series audio door entry system (using power supply) Installation Instructions IN9307.1

Transcription

1 Unit, AM Business Park umberland Avenue Park Royal, London, NW 7QL t : f : w : 4 Series audio door entry system (using 7. power supply) Installation Instructions IN7. 7 Getting started Thank you for choosing SRS. If you are installing this system with one or two entrance panel(s) continue to step. If however you are installing something more complicated, please call technical support for a specific diagram. Install the cables Use W (BT spec.) twisted paired cable. hoose cable layout fig. or fig. Any cable joint is potentially a cause of connection faults, it is therefore prudent to keep junctions to a minimum. For this reason we recommend making connections at the panel (max. telephones) or at ONE point in the riser (usually adjacent to the power supply ) fig. connections made in riser ac/dc fig. connections made in panel Install the telephones The telephones should be connected according to the diagram over l e a f. Ignore the dashed wires if additional features are not required. fig. 5mm 4 Install the entrance panel Please refer to the instructions (IN4) supplied with the door entry panel. 5 Operation The audio door entry system functions as follows. Upon pressing one of the external buttons the corresponding house phone sounds. When the called house phone handset is picked up, contact is established and conversation may take place. In order to operate the electric lock the push button marked by a key symbol should be fully depressed. 7 functions The 7 power supply unit (PSU) comes in two parts, The power unit (7.) and the relay unit (7.). The relay unit has lock release timer (with relay output), and the power unit has v ac, v dc, and tone outputs. When the lock release button on the phone is pressed, terminal and (at the phone) are shorted, causing the lock release timer to start which in turn changes the state of the relay. The time can be adjusted between 4 seconds (approx). The v ac (A) and v dc (D) terminals may be used to power lock releases up to.5 Amps. E requirements This product was tested for compliance with E directive //EE with the panel connected to Mains Earth. Always ensure that external metal parts are independently connected to mains protective earth to avoid electrical shock hazard. all tone options. Use v ac buzzer call. Move connection from (7 PSU) to A and move connections in all phones from to. Buzzer call is louder. It is also able to drive a standard v ac door bell!. Add an extension sounder One AN77 per call button may be used.. A different sounder You can use timer (SRS 57) to trigger any low voltage sounder device. 4. Solution for hard of hearing Strobe light (SRS 5) and inductive ear piece (44) are available for the hard of hearing. Remember Always fit the lock suppressor supplied, SRS T. This device must be connected to all electric locks and electric releases. Fit directly across the lock terminals. Trouble shooting The first rule of trouble shooting is to make your system as simple as possible. i e. Remove any nonessential connections. High pitched screech : Excessive amplification (volume requires adjustment) Unhooked handset hanging down & facing wall Short circuit on wires & Incorrect cable used Poor alignment of to hole in front plate. No speech heck for short circuits and/or breaks on wires &. heck V dc at unit Lock release will not trigger heck lock connections Remove cable(s) from at the 7 (PSU). Trigger input with egress button. If this corrects the fault, check wire to telephone. With a meter check lock relay output is changing state.

2 Drawing d nh e Date.. 4 Series audio door entry system n users, entrance ommon ve all Tone Input onnect to V D via door monitor switch onnect to V D able Maximum recommended overall distance for 4 pair (W BT spec.) cable run is metres. Make connections as shown in the diagram to avoid interference. ANS Telephone ommon ve all Tone Input Simultaneous all You may call up to 4 telephones at the same time. onnect,,, & in parallel. wires are shown connected in parallel for terminal, to the ve at the unit. This is intentional and should be followed for best results. ANS Telephone ommon ve all Tone Input This telephone has additional terminals ( and ) for Door Monitor and Nuisance switch with LED indication. Take power from the 7. power supply terminal D (V D). all Buttons 7. dio psu all Tone V D V V A 7. Lock Timer V D ve Trigger D A D Relay Normally losed N/ V GND Relay ommon Relay Normally Open White / Green & Egress Button 55M V V V D Fail Locked 7. D Note : 7. provides MAX 5mA V A or V D for lock Replace 7. connections for alternative PSU if more current is required V A Fail Locked 7. A 5mA 5mA 5mA V D Fail Open 7. D N/ 7.

3 Drawing d nh e 5 Date.. 4 Series audio door entry system n users, entrance with D5 Keypad ommon ve all Tone Input onnect to V D via door monitor switch onnect to V D able Maximum recommended overall distance for 4 pair (W BT spec.) cable run is metres. Make connections as shown in the diagram to avoid interference. ANS Telephone ommon ve all Tone Input Simultaneous all You may call up to 4 telephones at the same time. onnect,,, & in parallel. wires are shown connected in parallel for terminal, to the ve at the unit. This is intentional and should be followed for best results. ANS Telephone ommon ve all Tone Input This telephone has additional terminals ( and ) for Door Monitor and Nuisance switch with LED indication. Take power from the 7. power supply terminal D (V D). all Buttons 7. dio psu all Tone V D V V A D A White / Green & 55M V V D5 Keypad / 4V V N.. relay normally closed relay common N.O. relay normally open O/P INHIB EG IN Note : 7. provides MAX 5mA V A or V D for lock Replace 7. connections for alternative PSU if more current is required V D Fail Locked 7. V A Fail Locked 7. V D Fail Open 7. 5mA D 5mA A 5mA D D5 D5 D5 D5 N.O. N.O. N.O. N..

4 Drawing d nh e Date.. 4 Series audio door entry system n users, entrance with D5 Access ontrol ommon ve all Tone Input onnect to V D via door monitor switch onnect to V D able Maximum recommended overall distance for 4 pair (W BT spec.) cable run is metres. Make connections as shown in the diagram to avoid interference. ANS Telephone ommon ve all Tone Input Simultaneous all You may call up to 4 telephones at the same time. onnect,,, & in parallel. wires are shown connected in parallel for terminal, to the ve at the unit. This is intentional and should be followed for best results. ANS Telephone ommon ve all Tone Input This telephone has additional terminals ( and ) for Door Monitor and Nuisance switch with LED indication. Take power from the 7. power supply terminal D (V D). all Buttons 7. dio psu all Tone V D V V A D A White / Green & 55M V V V D psu V D V N D5 Access V V relay normally closed relay common relay normally open INH INHIB ommon for Egr & Mon MON Monitor EGR Egress Reader connections omitted for clarity V D Fail Locked EX V A Fail Locked 7. V D Fail Open EX.A D 5mA A.A D D5 D5 D5 N D5

5 Drawing d nh e Date.. 4 Series audio door entry system n users, entrances ommon ve all Tone Input onnect to V D via door monitor switch onnect to V D able Maximum recommended overall distance for 4 pair (W BT spec.) cable run is metres. Make connections as shown in the diagram to avoid interference. ANS Telephone ommon ve all Tone Input Simultaneous all You may call up to 4 telephones at the same time. onnect,,, & in parallel. wires are shown connected in parallel for terminal, to the ve at the unit. This is intentional and should be followed for best results. Position the power supply (7.) and Entrance Relay (AK54) close to each other ANS Telephone ommon ve all Tone Input This telephone has additional terminals ( and ) for Door Monitor and Nuisance switch with LED indication. Take power from the 7. power supply terminal D (V D). all Buttons all Buttons N Primary Entrance Secondary Entrance 55M V V P i N P P P all Tone Out all Tone In ve Lock all Tone Out all Tone In ve Lock S ii NA S S S 55M V V AK54 Entrance Relay 7. Lock Timer V D ve Trigger D V GND Relay Normally losed N/ Relay ommon Relay Normally Open 7. dio psu all Tone V V D D V A A D GND V 7. Lock Timer V D ve Trigger N/ Relay Normally losed Relay ommon Relay Normally Open V D Fail Locked D psu D 7. Note : 7. provides MAX 5mA V A. Do not use 7. 5mA D output for locking in this installation V A Fail Locked 7. V D Fail Open D psu 5mA A D N/ 7.

6 Drawing D H S Reference dio Diagram Handsets simultaneous call alling telephones at the same time.. Date ANS ANS ANS ANS ANS ANS V TRIG 7 timer 7. power supply N D A Mains Note you may call up to telephones at the same time. A further telephones may be called by adding another 7 power supply and a 57 timer. To entrance panel D H E T Drawing Reference dio Diagram Handsets Entrances Diagram showing TRADE button connections trades button.. Date Note: Trade button connections are shown in bold call button(s) TRADE button 55M unit Egress Button Push to Make connect common Power Relay of relay to V connection connection V A fail locked A V D fail locked D D A D GND N/ V V N/ V D fail open D N/ 7. power supply Mains 7. lock timer relay (4s) 5 time clock V D FAIL LOKED illustrated with transil fitted