Regulator Flow Curves For Bulk Gas Systems, Cylinder Gas Cabinets and Gas Distribution Systems Report # Rev 4
|
|
|
- Adela Kelly
- 7 years ago
- Views:
Transcription
1 Regulator Flow Curves For Bulk Gas Systems, Cylinder Gas Cabinets and Gas Distribution Systems Report # 383 Rev 4 June 5, 213 Scope: This document is a reference guide to help customers determine an appropriate AP Tech pressure regulator model based on system flow requirements. It is an array of regulator flow curves for the most popular AP Tech pressure regulators used in bulk gas systems, cylinder gas cabinets and gas distribution systems. For information and specifications related to the specific model regulator, please refer to the catalog data sheet. Advanced Pressure Technology 687 Technology Way Napa, CA Telephone:
2 General Recommendations Regulator Series AP11 (AZ11, AK11) AP11 HF (AZ11 HF, AK11 HF) AP111 (AP111, AZ111) AP111 HF (AP111 HF) AP121 (AZ121, AK121) AP121 HF (AZ121 HF, AK121 HF) AP121 FC (AZ121 FC, AK121 FC) AP142 TA (AZ142 TA) AP141T (AK141T) AP151 (AK151) Maximum Source Pressure (psig) Maximum Outlet Pressure (psig) Flow Coefficient, Cv Recommended Maximum Flow (slm nitrogen) 3, , , , , , , , AP191 HF 3, Page 2 of 8
3 General Recommendations AP91 1, , AP93 1, , AP , Page 3 of 8
4 General Notes 1. AZ and AK series regulators have the same flow performance as their AP counterpart (e.g. for an AK11 regulator refer to the AP11 flow curves and for an AZ121 regulator refer to the AP121 flow curves). 2. The recommended maximum flow might not be achievable depending on the inlet pressure. Please refer to specific flow curve conditions. 3. For applications where the inlet pressure is above 6 psig, use the 6 psig inlet pressure flow curve as the change in flow performance due to higher inlet pressure will not significantly change the shape of the flow curve. 4. Most regulator series are available with higher outlet pressure ranges although the source pressure may be lowered for certain models. Refer to the data sheet for the specific regulator or consult the factory to determine availability and specifications. 5. Some regulators have options that can affect the maximum source pressure, maximum outlet pressure, and recommended maximum flow rate. 6. In general, it is recommended that the regulator that meets the flow conditions and has the smallest flow coefficient be selected. Typically, this regulator would have better performance in other characteristics and cost less. Page 4 of 8
5 AP11 Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number 6 9, 5, 3 1/4 inch AP , 5, 3 1/4 inch AP11-2 AP11 AZ11 AK , 5, 3 1/4 inch AP , 5, 3 1/4 inch AP /4 inch AP11-5 Page 5 of 8
6 1 AP11S 2PW FV4 FV4 Flow Curve at 6 psig Inlet Pressure Page 6 of 8
7 1 AP11S 2PW FV4 FV4 Flow Curve at 3 psig Inlet Pressure Page 7 of 8
8 1 AP11S 2PW FV4 FV4 Flow Curve at 15 psig Inlet Pressure Page 8 of 8
9 8 AP11S 2PW FV4 FV4 Flow Curve at 1 psig Inlet Pressure Page 9 of 8
10 4 AP11S 2PW FV4 FV4 Flow Curve at 5 psig Inlet Pressure Page 1 of 8
11 AP11 HF Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number 6 9, 5, 3 1/4 inch AP11HF-1 3 9, 5, 3 1/4 inch AP11HF-2 AP11 HF AZ11 HF AK11 HF 15 9, 5, 3 1/4 inch AP11HF , 5, 3 1/4 inch AP11HF /4 inch AP11HF-5 Page 11 of 8
12 1 AP11S 2PW FV4 FV4 HF Flow Curve at 6 psig Inlet Pressure Page 12 of 8
13 1 AP11S 2PW FV4 FV4 HF Flow Curve at 3 psig Inlet Pressure Page 13 of 8
14 1 AP11S 2PW FV4 FV4 HF Flow Curve at 15 psig Inlet Pressure Page 14 of 8
15 8 AP11S 2PW FV4 FV4 HF Flow Curve at 1 psig Inlet Pressure Page 15 of 8
16 35 AP11S 2PW FV4 FV4 HF Flow Curve at 5 psig Inlet Pressure Page 16 of 8
17 AP111 Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (in Hg) Connection Size Flow Curve Number AP111 AZ , 15, 21 1/4 inch AP111_c AP111 HF 2 ¼ inch AP111HF_a Page 17 of 8
18 AP 111S FV4 FV4 Inlet Pressure = 1.45 psig (.1 Mpa) OUTLET PRESSURE (in.hg Vacuum) OUTLET PRESSURE (mm Hg Absolute) Flow Rate - SLPM Page 18 of 8
19 AP 111S HF FV4 FV4 Inlet Pressure 2 psig (.1 Mpa) OUTLET PRESSURE (in.hg Vacuum) OUTLET PRESSURE (mm Hg Absolute) Flow Rate - SLPM Page 19 of 8
20 AP121 Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP121 AZ121 AK , 5, 3 3 9, 5, , 5, , 5, /2 inch AP /4 inch AP /2 inch AP /4 inch AP /2 inch AP /4 inch AP /2 inch AP /4 inch AP /2 inch AP /4 inch AP121-1 Page 2 of 8
21 1 AP121S 2PW FV8 FV8 Flow Curve at 6 psig Inlet Pressure Page 21 of 8
22 1 AP121S 2PW FV12 FV12 Flow Curve at 6 psig Inlet Pressure Page 22 of 8
23 1 AP121S 2PW FV8 FV8 Flow Curve at 3 psig Inlet Pressure Page 23 of 8
24 1 AP121S 2PW FV12 FV12 Flow Curve at 3 psig Inlet Pressure Page 24 of 8
25 1 AP121S 2PW FV8 FV8 Flow Curve at 15 psig Inlet Pressure Page 25 of 8
26 1 AP121S 2PW FV12 FV12 Flow Curve at 15 psig Inlet Pressure Page 26 of 8
27 8 AP121S 2PW FV8 FV8 Flow Curve at 1 psig Inlet Pressure Page 27 of 8
28 8 AP121S 2PW FV12 FV12 Flow Curve at 1 psig Inlet Pressure Page 28 of 8
29 4 AP121S 2PW FV8 FV8 Flow Curve at 5 psig Inlet Pressure Page 29 of 8
30 4 AP121S 2PW FV12 FV12 Flow Curve at 5 psig Inlet Pressure Page 3 of 8
31 AP121 HF Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP121 HF AZ121 HF AK121 HF 6 9, 5, 3 3 9, 5, , 5, , 5, /2 inch AP121HF-1 3/4 inch AP121HF-2 1/2 inch AP121HF-3 3/4 inch AP121HF-4 1/2 inch AP121HF-5 3/4 inch AP121HF-6 1/2 inch AP121HF-7 3/4 inch AP121HF-8 1/2 inch AP121HF-9 3/4 inch AP121HF-1 Page 31 of 8
32 1 AP121S 2PW FV8 FV8 HF Flow Curve at 6 psig Inlet Pressure Page 32 of 8
33 1 AP121S 2PW FV12 FV12 HF Flow Curve at 6 psig Inlet Pressure Page 33 of 8
34 1 AP121S 2PW FV8 FV8 HF Flow Curve at 3 psig Inlet Pressure Page 34 of 8
35 1 AP121S 2PW FV12 FV12 HF Flow Curve at 3 psig Inlet Pressure Page 35 of 8
36 1 AP121S 2PW FV8 FV8 HF Flow Curve at 15 psig Inlet Pressure Page 36 of 8
37 1 AP121S 2PW FV12 FV12 HF Flow Curve at 15 psig Inlet Pressure Page 37 of 8
38 8 AP121S 2PW FV8 FV8 HF Flow Curve at 1 psig Inlet Pressure Page 38 of 8
39 8 AP121S 2PW FV12 FV12 HF Flow Curve at 1 psig Inlet Pressure Page 39 of 8
40 4 AP121S 2PW FV8 FV8 HF Flow Curve at 5 psig Inlet Pressure Page 4 of 8
41 4 AP121S 2PW FV12 FV12 HF Flow Curve at 5 psig Inlet Pressure Page 41 of 8
42 AP121 FC Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP121 FC AZ121 FC AK121 FC 15 75, 5, , 5, /2 inch AP121FC-1 3/4 inch AP121FC-2 1/2 inch AP121FC-3 3/4 inch AP121FC-4 1/2 inch AP121FC-5 3/4 inch AP121FC-6 Page 42 of 8
43 8 AP121S 2PW FV8 FV8 FC Flow Curve at 15 psig Inlet Pressure Page 43 of 8
44 8 AP121S 2PW FV12 FV12 FC Flow Curve at 15 psig Inlet Pressure Page 44 of 8
45 8 AP121S 2PW FV8 FV8 FC Flow Curve at 1 psig Inlet Pressure Page 45 of 8
46 8 AP121S 2PW FV12 FV12 FC Flow Curve at 1 psig Inlet Pressure Page 46 of 8
47 4 AP121S 2PW FV8 FV8 FC Flow Curve at 5 psig Inlet Pressure Page 47 of 8
48 4 AP121S 2PW FV12 FV12 FC Flow Curve at 5 psig Inlet Pressure Page 48 of 8
49 AP142TA Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures Connection Size Flow Curve Number, 1, 18 in Hg (vac) 1/4 inch AP142TA AP142TA AK142TA in Hg (vac) 1/4 inch AP142TA_a 1 in Hg (vac) 1/4 inch AP142TA_e 3 1 psig 1/4 inch AP142TA_c Page 49 of 8
50 AP 142 TSA 2PW FV4 FV4 Inlet Pressure = psig (76 mm Hg) Outlet Pressure (in. Hg Vacuum) Outlet Pressure (mm Hg Absolute) Flow Rate (slpm Nitrogen) Page 5 of 8
51 AP 142 TSA 2PW FV4 FV4 Inlet Pressure - 2psig (76) 5 (66) (56) OUTLET PRESSURE (in.hg of Vacuum) (46) (36) (26) OUTLET PRESSURE (mm Hg Absolute) 25 (16) (6) Flow Rate in SLPM of Nitrogen Page 51 of 8
52 AP 142 TSA 2PW FV4 FV4 Inlet Pressure - 1 psig (76) 5 (66) (56) 1 OUTLET PRESSURE (in.hg of Vacuum) 15 2 (46) (36) (26) OUTLET PRESSURE (mm Hg Absolute) 25 (16) (6) Flow Rate in SLPM of Nitrogen Page 52 of 8
53 2 AP 142 TSA 2PW FV4 FV4 Inlet Pressure - 3 psig (.2 MPa) Outlet Pressure, MPa Flow Rate, slpm nitrogen. Page 53 of 8
54 AP141T Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP141T AK141T 6 9, 5, 3 3 9, 5, , 5, /4 inch AP141T-1 1/2 inch AP141T-2 1/4 inch AP141T-3 1/2 inch AP141T-4 1/4 inch AP141T-5 1/2 inch AP141T-6 1/4 inch AP141T-7 1/2 inch AP141T-8 Page 54 of 8
55 1 AP141TS 2PW FV4 FV4 Flow Curve at 6 psig Inlet Pressure Page 55 of 8
56 1 AP141TS 2PW FV8 FV8 Flow Curve at 6 psig Inlet Pressure Page 56 of 8
57 1 AP141TS 2PW FV4 FV4 Flow Curve at 3 psig Inlet Pressure Page 57 of 8
58 1 AP141TS 2PW FV8 FV8 Flow Curve at 3 psig Inlet Pressure Page 58 of 8
59 8 AP141TS 2PW FV4 FV4 Flow Curve at 1 psig Inlet Pressure Page 59 of 8
60 8 AP141TS 2PW FV8 FV8 Flow Curve at 1 psig Inlet Pressure Page 6 of 8
61 4 AP141TS 2PW FV4 FV4 Flow Curve at 5 psig Inlet Pressure Page 61 of 8
62 4 AP141TS 2PW FV8 FV8 Flow Curve at 5 psig Inlet Pressure Page 62 of 8
63 AP151 Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number 6 9, 5, 3 1/4 inch AP , 5, 3 1/4 inch AP151-2 AP151 AK , 5, 3 1/4 inch AP , 5, 3 1/4 inch AP /4 inch AP151-5 Page 63 of 8
64 1 AP151S 2PW FV4 FV4 Flow Curve at 6 psig Inlet Pressure Page 64 of 8
65 1 AP151S 2PW FV4 FV4 Flow Curve at 3 psig Inlet Pressure Page 65 of 8
66 1 AP151S 2PW FV4 FV4 Flow Curve at 15 psig Inlet Pressure Page 66 of 8
67 8 AP151S 2PW FV4 FV4 Flow Curve at 1 psig Inlet Pressure Page 67 of 8
68 4 AP151S 2PW FV4 FV4 Flow Curve at 5 psig Inlet Pressure Page 68 of 8
69 AP191 HF Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP191 HF 6 9, 5, 3 3 9, 5, , 5, 3 1/4 inch AP191HF-1 1/2 inch AP191HF-2 1/4 inch AP191HF-3 1/2 inch AP191HF-4 1/4 inch AP191HF-5 1/2 inch AP191HF-6 Page 69 of 8
70 1 AP191S 2PW FV4 FV4 HF Flow Curve at 6 psig Inlet Pressure Page 7 of 8
71 1 AP191S 2PW FV8 FV8 HF Flow Curve at 6 psig Inlet Pressure Page 71 of 8
72 1 AP191S 2PW FV4 FV4 HF Flow Curve at 3 psig Inlet Pressure Page 72 of 8
73 1 AP191S 2PW FV8 FV8 HF Flow Curve at 3 psig Inlet Pressure Page 73 of 8
74 8 AP191S 2PW FV4 FV4 HF Flow Curve at 1 psig Inlet Pressure Page 74 of 8
75 8 AP191S 2PW FV8 FV8 HF Flow Curve at 1 psig Inlet Pressure Page 75 of 8
76 AP9 Flow Curve Index Series Inlet Pressure (psig) Outlet Pressures (psig) Connection Size Flow Curve Number AP91 6 9, 5, 3 3 9, 5, , 5, 3 3/4 inch AP inch AP91-2 3/4 inch AP inch AP91-4 3/4 inch AP inch AP91-6 AP , 5, 3 3/4 inch AP inch AP93-2 3/4 inch AP inch AP911-2 AP , 5, , 5, 3 3/4 inch AP inch AP /4 inch AP inch AP911-6 Page 76 of 8
77 1 AP91S 2PW FV12 FV12 Flow Curve at 6 psig Inlet Pressure Page 77 of 8
78 1 AP91S 2PW FV16 FV16 Flow Curve at 6 psig Inlet Pressure Page 78 of 8
79 1 AP91S 2PW FV12 FV12 Flow Curve at 3 psig Inlet Pressure Page 79 of 8
80 1 AP91S 2PW FV16 FV16 Flow Curve at 3 psig Inlet Pressure Page 8 of 8
81 8 AP91S 2PW FV12 FV12 Flow Curve at 1 psig Inlet Pressure Page 81 of 8
82 8 AP91S 2PW FV16 FV16 Flow Curve at 1 psig Inlet Pressure Page 82 of 8
83 3 AP93S 2PW FV12 FV12 Flow Curve at 6 psig Inlet Pressure Page 83 of 8
84 3 AP93S 2PW FV16 FV16 Flow Curve at 6 psig Inlet Pressure Page 84 of 8
85 1 AP911S 2PW FV12 FV12 Flow Curve at 3 psig Inlet Pressure Page 85 of 8
86 1 AP911S 2PW FV16 FV16 Flow Curve at 3 psig Inlet Pressure Page 86 of 8
87 1 AP911S 2PW FV12 FV12 Flow Curve at 15 psig Inlet Pressure Page 87 of 8
88 1 AP911S 2PW FV16 FV16 Flow Curve at 15 psig Inlet Pressure Page 88 of 8
89 8 AP911S 2PW FV12 FV12 Flow Curve at 1 psig Inlet Pressure Page 89 of 8
90 8 AP911S 2PW FV16 FV16 Flow Curve at 1 psig Inlet Pressure Page 9 of 8
Check Valve. Series AP64. How to Order. Specifications. Wetted Parts Material
Check Valve Series AP4 Simple design with free of springs and poppets Reseals with minimal back pressure Low cracking pressure AP4 S How to Order (Inlet) (Outlet) Material Code Body material S L SS secondary
ball valves Flomite 71 Series 2-way Integral Panel Mount Ball Valves
2-way Integral Panel Mount Ball Valves Used for quick on-off service with a visual indication of flow, HOKE s 2-way ball valves offer orifice sizes up to 0.25 (6.4mm). Flomite valves feature a floating
Recharge Procedure for Telemark TVP-2000 and TVP-3500
Recharge Procedure for Telemark TVP-2000 and TVP-3500 Required items: 1.) Refrigeration service manifold. 2.) Charge recovery system. 3.) Dry nitrogen gas. If a high pressure cylinder is used, a pressure
G234X-55 Conventional Gas Boiler
Engineering Submittal Sheet Boiler Overview C US Engineering Specifications There shall be provided and installed a quantity of Buderus G234X-55 fl oor standing hot water boiler(s), suitable with natural
A practical guide to restrictive flow orifices
Safetygram 46 A practical guide to restrictive flow orifices Restrictive flow orifices (RFOs) installed in cylinder valve outlets provide a significant safety benefit for users of hazardous gases, especially
OEM-EP Pressure Controllers
Pressure Controllers Typical Applications Carrier Gas Pressure Control Air over Liquid Control Mass Spectrometer Process Gas Supply Pressure Control Miniature ler The Miniature ler converts a variable
Model 111 Mass Flow Instruments
111 Mass Instruments Porter Mass products reflect over four decades of experience in the design and manufacture of precision instruments for the measurement and control of gas flow. They incorporate design
AUTOMATIC CHANGEOVER MANIFOLD Series 915
AUTOMATIC CHANGEOVER MANIFOLD Series 915 FEATURES Fully automatic, simple, hassle-free operation No variance in delivery pressure Designed for ultra high purity gas service Built-in audio and visual alarm
CITY OF LOS ANGELES CALIFORNIA
BOARD OF BUILDING AND SAFETY COMMISSIONERS MARSHA L. BROWN PRESIDENT PEDRO BIRBA VICE-PRESIDENT VAN AMBATIELOS HELENA JUBANY ELENORE A. WILLIAMS November 14, 2007 CITY OF LOS ANGELES CALIFORNIA ANTONIO
Regulator Performance Data
Regulator Performance Data The regulator flow data is provided to assist in determining the proper regulator for the required application. The data is given for reference purpose only. If additional information
Laminar Flow Elements
Laminar Flow Elements Meriam Laminar Flow Elements (LFEs) are excellent for measuring low gas flow rates from 0.2 SCCM up to 2250 SCFM. They are inherently accurate and repeatable and are calibrated traceable
Vacuum Control. Vacuum Applications. Vacuum Regulators. Vacuum Breakers (Relief Valves) Vacuum Control Devices. Vacuum Terminology
Vacuum Applications Vacuum regulators and breakers are widely used in process plants. Conventional regulators and relief valves might be suitable for service if applied correctly. This section provides
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223 HERION S HIGH PERFORMANCE POPPET VALVES For those applications requiring high Cv, fast response times, large
KNC Model 3666 Automatic Pressure Calibration System
KNC Model 3666 Automatic Pressure Calibration System Product Description The Model 3666 Automatic Pressure Calibration (APC) System by King Nutronics Corporation is a portable secondary standards laboratory
Meriam Instrument LFE Data Sheet
1. AIR FLOW IN SCFM AT STANDARD CONDITIONS OF 29.92 AND 70 F. SCFM = Standard cubic feet per minute. ACFM = Actual cubic feet per minute CFM = Cubic feet per minute. When the flowing gas is air and the
Element D Services Plumbing
Medical Vacuum and Gas PART 1 - GENERAL 1.01 OVERVIEW A. This section addresses medical vacuum, waste anesthetic gas disposal, compressed air, oxygen, nitrous oxide, nitrogen and carbon dioxide systems.
Compact, High-Flow Gas Regulators
www.swagelok.com Compact, High-Flow Gas Regulators HF Series Precise pressure control Tamper-free design High-purity design Preset and adjustable dome-loaded models 2 Compact, High-Flow Gas Regulators
Centro-Matic Automatic Lubrication Systems System Controls
Selecting the right controls for your automated lubrication system is one of the last steps in the design process. Several different models may be chosen to control power-operated pumps, depending on the
NOTE: If the HF body is stamped HFK, then the cage is replaceable. HF N E S C B 2 H C 5 FT 3/8 x 1/2 ODF S/T Valve Series
The HF series is a balanced ported valve designed for refrigeration, air conditioning and heat pump applications. Features Stainless steel replaceable power element eliminates corrosion and prevents valve
ENDURANCE Conductivity Sensors
Instruction Manual 400 and 400VP LIQ_MAN_ABR_400_400VP December 2013 ENDURANCE Conductivity Sensors For additional information, please refer visit our website at www.rosemountanalytical.com. CAUTION Sensor/Process
SPECIFICATION SHEET : WH5-120-L
SPECIFICATION SHEET : WH5120L *F3 2 T8 3 1 0 6 0.9 3 1.2 6 1.1 9 *F3 2 T8 4 1 2 7 1.1 3 1.1 1 0.8 7 F5 4 T5 H O 2 1 0 8 0.9 6 1.0 7 0.9 9 *F5 8 T8 2 1 1 0 0.9 7 1.0 8 0.9 8 *F4 0 T1 0 2 1 0 1 0.9 0 1.3
Side-Trak 830/840. Process Gas Mass Flow Meters and Controllers. www.sierrainstruments.com
Process Gas Mass Flow Meters and Controllers Features n Direct monitoring of mass flow eliminates need for ancillary pressure and temperature sensing n Patented straight sensor tube with access ports permits
PORTER MASS FLOW MEASUREMENT AND CONTROL SYSTEMS
PORTER MASS MEASUREMENT AND CONTROL SYSTEMS PORTER: THE STANDARD OF EXCELLENCE IN MASS Porter Mass Flow products reflect nearly three decades of experience in the design and manufacture of precision instruments
BASIC UNDERSTANDING OF FLOW CALCULATIONS AND ESTIMATES MAKES SIZING VALVES SIMPLER
BASIC UNDERSTANDING OF FLOW CALCULATIONS AND ESTIMATES MAKES SIZING VALVES SIMPLER Valve size often is described by the nominal size of the end connections but a more important measure is the flow that
RUSKA PRODUCTS - PRICE LIST
RUSKA PRODUCTS - PRICE LIST Effective Date: This price list is effective January 1, 2010 and supersedes all previous price lists for the items contained herein. NVLAP An optional ISO 17025 accredited calibration
1. A belt pulley is 3 ft. in diameter and rotates at 250 rpm. The belt which is 5 ins. wide makes an angle of contact of 190 over the pulley.
Sample Questions REVISED FIRST CLASS PARTS A1, A2, AND A3 (NOTE: these questions are intended as representations of the style of questions that may appear on examinations. They are not intended as study
Regulator Options and Accessories
Regulator Options and Accessories Regulator accessories are available separately or mounted on Swagelok regulators. Some accessories limit regulator pressure or temperature ratings. Additional materials,
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES DIRECT ACTING Brochure N-289 SPECIFICATIONS Port Size: 1/8 and1/4 Solenoid Valve for air, oil, water and other fluids Flow Direction:
Tubing and Accessories
Section 7 Tubing and Accessories Inch Industrial Tubing................................FIT-7-2 Metric Industrial Tubing...............................FIT-7-3 Inch D.O.T. Tubing...................................FIT-7-3
Veriflo Pressure Regulators
Hydraulik - Pneumatik Steffen Haupt Moritzer Straße 35 01589 Riesa Telefon: 03525 6801-0 Telefax: 03525 680120 info@haupt-hydraulik.de Veriflo Pressure Regulators 4511 November 2003 KATALOG Vertrieb: Frau
REAL CHAMBERS CORPORATION SQL PRE-INSTALLATION/ SITE PREPARATION MANUAL
REAL CHAMBERS CORPORATION SQL PRE-INSTALLATION/ SITE PREPARATION MANUAL Real Chambers Corporation 10392 E. 48 th Avenue Denver, CO 80238 USA 23001048 Rev. E 1 of 7 TABLE OF CONTENTS OVERVIEW... 3 SAFETY...
needle valves Needle Valves Index At a Glance 1
Needle Valves Index At a Glance 1 1700 Series 5 Forged Body, Integral Bonnet Needle Valves 2100 Series 8 Bar Stock, Screwed Bonnet Needle Valves 2200 Series 12 Bar Stock, Screwed Bonnet Needle Valves 2219
1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
UNDERSTANDING REFRIGERANT TABLES
Refrigeration Service Engineers Society 1666 Rand Road Des Plaines, Illinois 60016 UNDERSTANDING REFRIGERANT TABLES INTRODUCTION A Mollier diagram is a graphical representation of the properties of a refrigerant,
Series PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2662-CD/US Revised June, 212 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference
ACFM vs. SCFM vs. ICFM Series of Technical White Papers from Ohio Medical Corporation
ACFM vs. SCFM vs. ICFM Series of Technical White Papers from Ohio Medical Corporation Ohio Medical Corporation 1111 Lakeside Drive Gurnee, IL 60031 Phone: (800) 448-0770 Fax: (847) 855-6304 info@ohiomedical.com
EVAC ONLINEVAC TECHNICAL DATA 6547655 EVAC ONLINEVAC 16, 24 V DC. Required maintenance space 700 mm. Required maintenance space 200 mm 360 Ø13
Date: 9 Apr 202 Doc. 002967-6547655 6, 24 V DC Ø3 360 Required maintenance 990±0 960 40 040 20 890 350 (P/N 546664) 95±5 67±5 Vacuum sensor G /4 88±5 INLET DN40 943 Connection Frame: Steel S235 EN 0025
Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Valve Sizing 408-409
Engineering Data Table of Contents Page No. I II Formulas, Conversions & Guidelines Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Sizing 408-409 Steam
4 Posiflow Proportional Solenoid Valves
4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,
Lesson 4: Surface Area
Lesson 4: Surface Area Selected Content Standards Benchmarks Addressed: M-1-M Applying the concepts of length, area, surface area, volume, capacity, weight, mass, money, time, temperature, and rate to
In-Line Electronic Flow Switches
In-Line Electronic Flow Switches Industries Petrochemical Refining Oil Production Water Treatment Pharmaceutical Food and Beverage Pulp and Paper Power Production Gas Processing Mining Biotechnology Semiconductor
HOW TO SIZE A PRESSURE REGULATOR
CHOOSING THE CORRECT REGULATOR HOW TO SIZE A PRESSURE REGULATOR In order to choose the correct regulator the following information is needed: - Function: Pressure reducing or backpressure control? - Pressure:
GTM PORTABLE GAS TRANSPORT. a breakthrough in high pressure gas transports, holding twice as much a comparable steel transports at 40% of the weight
GTM PORTABLE GAS TRANSPORT a breakthrough in high pressure gas transports, holding twice as much a comparable steel transports at 40% of the weight Transporting high pressure gases with current applications
TEST REPORT for the ARID TECHNOLOGIES VAPOR RECOVERY UNIT installed in LANTANA, FL
Project No. 148 TEST REPORT for the ARID TECHNOLOGIES VAPOR RECOVERY UNIT installed in LANTANA, FL Prepared for: Mr. Ted Tiberi Arid Technologies, Inc. 130 North LaGrange Rd. LaGrange, IL 60525 Prepared
Valve Sizing. Te chnic al Bulletin. Flow Calculation Principles. Scope. Sizing Valves. Safe Product Selection. www.swagelok.com
www.swagelok.com Valve Sizing Te chnic al Bulletin Scope Valve size often is described by the nominal size of the end connections, but a more important measure is the flow that the valve can provide. And
Technical & Sizing Bulletin for Meriam LFEs. Laminar Flow Elements
Technical & Sizing Bulletin for Meriam LFEs Laminar Flow Elements What they are... Meriam Laminar Flow Elements are gas volume rate of flow differential producers operating on capillary flow principles.
solenoid valves SV Series 2- and 3-way Solenoid Valves for Gas and Liquid
2- and 3-way Solenoid Valves for Gas and Liquid SV10: Vacuum to 3000 psig SV430: Vacuum to 3000 psig SV20: Vacuum to 6000 psig SV460: Vacuum to 6000 psig SV30: Vacuum to 3000 psig Circle Seal Controls
THE ADVANCED DENTAL DRY VAC DENTAL SYSTEMS
TM THE ADVANCED DENTAL DRY VAC 100% Oil & Water Free Suction Systems Compact & Expandable Suction Systems Custom Engineered Large Scale Systems Portable Surgical Suction Systems The creation of vacuum
Green Thread Product Data
Green Thread Product Data Applications Dilute Acids Caustics Produced Water Industrial Waste Hot Water Condensate Return Materials and Construction All pipe manufactured by filament winding process using
In-Line Electronic Flow Switches
In-Line Electronic Flow Switches Industries Petrochemical Refining Oil Production Water Treatment Pharmaceutical Food and Beverage Pulp and Paper Power Production Gas Processing Mining Biotechnology Semiconductor
RESPONSE TIME INDEX OF SPRINKLERS
, Number l, p.1-6, 29 RESPONSE TIME INDEX OF SPRINKLERS C.K. Sze Department of Building Services Engineering, The Hong Kong Polytechnic University, Hong Kong, China ABSTRACT The Plunge test would be carried
OHIO MEDICAL CORPORATION. Medical Gas Panel. Installation and Maintenance Manual
OHIO MEDICAL CORPORATION Medical Gas Panel Installation and Maintenance Manual P/N 255105 (Rev.5) 08/2005 P/N 255105 (Rev.5) 08/2005 PAGE 2 OHIO MEDICAL CORPORATION PAGE 3 1.0 User Responsibilities The
CHEMICAL ENGINEERING LABORATORY 3, CE 427 DRYING OF SOLIDS
Revised 10/00 CHEMICAL ENGINEERING LABORATORY 3, CE 427 DRYING OF SOLIDS Introduction Material covered here pertains to Chapter 24 of M,S&H. Please read relevant sections of this chapter. Drying involves
Lesson 4: Surface Area
Lesson 4: Surface Area Selected Content Standards Benchmark Assessed M.3 Estimating, computing, and applying physical measurement using suitable units (e.g., calculate perimeter and area of plane figures,
P3000 Series. Pneumatic Deadweight Testers Model P3000. Technical Data. Features
P3000 Series Pneumatic Deadweight Testers P3000 Technical Data Features Pressure ranges from Vacuum through 2 000 psi (140 bar) Accuracy better than 0.015 % of reading. (Increased accuracy option of 0.008
FLUID MECHANICS. TUTORIAL No.7 FLUID FORCES. When you have completed this tutorial you should be able to. Solve forces due to pressure difference.
FLUID MECHANICS TUTORIAL No.7 FLUID FORCES When you have completed this tutorial you should be able to Solve forces due to pressure difference. Solve problems due to momentum changes. Solve problems involving
Finding Volume of Rectangular Prisms
MA.FL.7.G.2.1 Justify and apply formulas for surface area and volume of pyramids, prisms, cylinders, and cones. MA.7.G.2.2 Use formulas to find surface areas and volume of three-dimensional composite shapes.
SIMPLIFIED METHOD FOR ESTIMATING THE FLIGHT PERFORMANCE OF A HOBBY ROCKET
SIMPLIFIED METHOD FOR ESTIMATING THE FLIGHT PERFORMANCE OF A HOBBY ROCKET WWW.NAKKA-ROCKETRY.NET February 007 Rev.1 March 007 1 Introduction As part of the design process for a hobby rocket, it is very
Outdoor Cooking. Gas pressure Regulators & Accessories 2012 EDITION LPG & NATURAL GAS REGULATORS RE-02 DIVISION
Outdoor Cooking Gas pressure Regulators & Accessories 2012 EDITION RE-02 Outdoor cooking Product index 1 - Introduction P.4 1.1 Gas pressure regulators P.4 1.2 Low pressure installations P.4 1.3 High pressure
Digital pressure gauge for industrial applications Model DG-10-S, Standard version Model DG-10-E, Enhanced version
Electronic pressure measurement Digital pressure gauge for industrial applications Model DG-10-S, Standard version Model DG-10-E, Enhanced version WIKA data sheet PE 81.66 Applications Machine building
Chem 115 POGIL Worksheet - Week 4 Moles & Stoichiometry
Chem 115 POGIL Worksheet - Week 4 Moles & Stoichiometry Why? Chemists are concerned with mass relationships in chemical reactions, usually run on a macroscopic scale (grams, kilograms, etc.). To deal with
Series PAVC Variable Displacement Piston Pumps zp01. Catalog HY28-2662-CD/US
Series PAVC Variable Displacement Piston Pumps zp1 Catalog HY28-2662-CD/US 1 Introduction Series PAVC Quick Reference Data Chart Pump Model Displacement CM 3 /REV (IN 3 /REV) Pump Delivery *Approx. Noise
RPS 8000. High Accuracy Resonant Pressure Sensor. GE Measurement & Control Solutions. Features:
GE Measurement & Control Solutions RPS 8000 High Accuracy Resonant Pressure Sensor For over 35 years, Druck has manufactured precision pressure sensors with a capability to meet critical applications in
LED Floodlight with Motion Sensor
LED Floodlight with Motion Sensor Catalog Number Notes Features & Specifications INTENDED USE Provides maintenance-free general illumination for outdoor applications. Ideal illumination for walkways, yards,
Fisher 377 Trip Valve
377 Trip Valve Product Bulletin Fisher 377 Trip Valve Fisher 377 pressure sensing trip valves are for control applications where a specific valve/actuator action is required when supply pressure falls
Valve and Valve Actuator Selection Guide
www.sbt.siemens.com/hvp/components Building Technologies Building Technologies Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 USA Tel 847 215 1000 Siemens Building
batimet Systemdetails
batimet TA35 DSP DSE System elements type catalog 5921001 007 : 0 5921001 elements type catalog 5921002 008 : 0 5921002 elements type catalog 5921003 009 : 0 5921003 elements type catalog 5921501 010 :
Experiment #3, Ohm s Law
Experiment #3, Ohm s Law 1 Purpose Physics 182 - Summer 2013 - Experiment #3 1 To investigate the -oltage, -, characteristics of a carbon resistor at room temperature and at liquid nitrogen temperature,
Medical Gas Installation Handbook A-Z. A guide to installing Medical Gas equipment from alarm panels to zone valves.
Medical Gas Installation Handbook A-Z A guide to installing Medical Gas equipment from alarm panels to zone valves. Table of Contents 1.0 Alarms 1.1 Area 1.2 Local 1.3 Master 2.0 Outlets 2.1 Station Outlets/Inlets
Surface Area Quick Review: CH 5
I hope you had an exceptional Christmas Break.. Now it's time to learn some more math!! :) Surface Area Quick Review: CH 5 Find the surface area of each of these shapes: 8 cm 12 cm 4cm 11 cm 7 cm Find
Pipeline. Medical Gas Pipeline Products
Pipeline Medical Gas Pipeline Products w w w. a m i c o. c o m The Amico Group Manufactures the Building Blocks of the Hospital Architectural Beds Lights Interiors Accessories Patient Care Diagnostic OR
Ball Valves (HB Series) Catalog 4121-HB Revised, April 2005
Ball Valves (HB Series) Revised, April 2005 Introduction Parker High Pressure HB4 Series Ball Valves provide reliable shut-off or switching functions. The upper and lower trunnion bearings enhance the
Electronic Wallmount Faucet 1500T4 & 1501T4 Series
Electronic Wallmount Faucet 1500T4 & 1501T4 Series Specification: (example) Battery (4 C cell) or Hardwire (24 VAC) infrared electronic handwash system H 2OPTICS technology no external adjustments required
Commercial Semi-Instantaneous Water Heaters
FEATURES HWI Models A. O. Smith s HWI models are available for operation with steam or boiler water as the energy source. They are factory assembled with components sized, piped and checked at the factory
Product Showcase. A Division of Bionix Since 1993 TESTING MADE EASY. SAFETY MADE SIMPLE.
The Smart Way to Manage Your Testing National Safety Technologies manufacturers and distributes testing and measurement devices for healthcare facilities that make required testing easy. A Division of
ZA-12. Temperature - Liquidus + 45 o C (81 o C) Vacuum = 90mm
Ragonne Fluidity, Inches Zn-Al Impact 38 34 30 26 22 18 14 No. 3 Zn-Al ZA-8 Liquidius ZA-12 Temperature - Liquidus + 45 o C (81 o C) Vacuum = 90mm Zn-Al (0.01-0.02 percent mg) ZA-27 10 0 2 4 6 8 10 12
Installation and Operating Manual Model F1800C Model F1800PG Model F1802C Model F1802PG Model F1806C Model F1806PG
Installation and Operating Manual Model F1800C Model F1800PG Model F180C Model F180PG Model F1806C Model F1806PG www.ipsystemsusa.com Contents Safety Warnings... Items supplied... Description... Installation...4
Measurement Solutions for Refrigeration Technology.
Measurement Solutions for Refrigeration Technology. Digital manifold, leak detection, vacuum measurement, and lots more. Testo refrigeration technology Digital is better: Refrigeration technology expertise
Vogt Valves The Connection Bulletin for Forged Steel Flow Control Valves CB 15
The Connection Bulletin for Forged Steel Flow Control Valves CB 15 Flow Control Division Forged Steel Flow Control Valves GRADUATED DIAL AND INDICATOR FULLY GUIDED V-PORT THROTTLING DISC AND INTEGRAL HARD
1800C and 1800C-HC Series Service Regulators. Technical Bulletin
and -H Series Service Regulators Technical Bulletin and -H Series Service Regulators 0 Elster American Meter The Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide,
Type 3353 Angle Seat Valve
Type 3353 Angle Seat Valve Application On/off valve with pneumatic piston actuator Nominal size DN 15 to 50 (NPS ½ to 2) Nominal pressure PN Temperature range 10 to 180 C Globe valve with an angle seat
T a b l e o f C o n t e n t s
w w w. g e n t e c h e a l t h c a r e. c o m M E D I C A L M O N I T O R I N G, A L A R M A N D C O N T R O L S Y S T E M S I n t e r n a t i o n a l E d i t i o n Technology for a Better Future Company
Fluid Power Formula. These Formula Cover All Fluid Power Applications In This Manual
These Formula Cover All Fluid Power Applications In This Manual For Computer Programs To Work Problems By Simply Filling In The Blanks See Your Local Fluid Power Distributor Many Companies Web Site Or
MEASURES OF VARIATION
NORMAL DISTRIBTIONS MEASURES OF VARIATION In statistics, it is important to measure the spread of data. A simple way to measure spread is to find the range. But statisticians want to know if the data are
Types 66R and 66RR Low-Pressure Relief Valves
November 2009 Types 66R and 66RR Low-Pressure Relief Valves W1953 W1908 TYPE 66R RELIEF VALVE TYPE 66RR RELIEF VALVE Figure 1. Typical Constructions Introduction Types 66R and 66RR low-pressure throttling
T U R B I N E G A S M E T E R
TURBINE GAS METER TURBINE GAS METER CGT 1 2 3 4 5 6 7 Design and function page 2 General technical data page 3 Measurement outputs page 4 Dimensions and weights page 5 Performance page 7 Pressure loss
Steam Jet Vacuum Pumps
By: S.G. Ketterer and C.G. Blatchley The use of steam jet ejectors for entraining air or gases at subatmospheric pressures is increasing rapidly, particularly in the range of pressures below mm absolute.
Miniature Pneumatic Solenoid Valve. Power Options: 0.5 Watt (6 psig model) 1.0 Watt (30, 100 psig model) Voltage Options: 3, 5, 12 or 24 VDC
8mm Solenoid Valve Typical Applications Portable Equipment Blood Pressure Monitoring Wound Therapy Air and Oxygen Delivery Sensor Zeroing Product Specifications Mechanical Valve Type: 3-Way, Solenoid-actuated
Recreational Vehicles
Recreational Vehicles Gas pressure Regulators & Accessories 2012 EDITION RE-01 Recreational vehicles Product index 1 - Introduction P.4 1.1 Pressure Gas Regulators P.4 1.2 Installations P.4 1.3 Backflow
BUFFER TANKS. ASME Commercial Buffer Tanks
BUFFER TNKS SME Commercial Buffer Tanks For Closed Thermal For Closed Water Loop Systems BUFFER TNKS mtrol SME Buffer Tanks add capacity to non-potable, closed systems to help reduce cycling, improve temperature
Sample Coolers. Water Steam Process. The largest selection of models offered by any manufacturer. www.sentry-equip.com
Sample Coolers Water Steam Process The largest selection of models offered by any manufacturer More than 85 Years of Sampling Experience Cool, Heat or Condense Any Sample Sentry has more types of sample
RPS/DPS 8100. High Accuracy Resonant Pressure Sensor. GE Measurement & Control. Features:
GE Measurement & Control RPS/DPS 8100 High Accuracy Resonant Pressure Sensor For over 40 years, Druck has manufactured precision pressure sensors with a capability to meet critical applications in industrial,
Accumulators and Receivers
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Accumulators and Receivers Catalog C-1, October 2007 Page 2 / Catalog
Practice Problems on Pumps. Answer(s): Q 2 = 1850 gpm H 2 = 41.7 ft W = 24.1 hp. C. Wassgren, Purdue University Page 1 of 16 Last Updated: 2010 Oct 29
_02 A centrifugal with a 12 in. diameter impeller requires a power input of 60 hp when the flowrate is 3200 gpm against a 60 ft head. The impeller is changed to one with a 10 in. diameter. Determine the
DSL & SVK Lubricators Product Specs and Ordering
Fred C. Gilbert Co. 106 Norris oad Bakersfield, Ca. 93308 661-399-9569 fax 661-393-9654 DSL & SVK Lubricators Product Specs and Ordering Bulletin SVK LUBICATO SVK PUMP WITH LIQUID FILLED SIGHT FEED DSL
Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc.
ASGMT / Averaging Pitot Tube Flow Measurement Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc. Averaging Pitot Tube Meters Introduction
MC4-50 Feeding System
MC4-50 Feeding System Dry Calcium Hypochlorite For Municipal Applications The smarter way to water quality PATENTED SPRAY TECHNOLOGY DELIVERS UNPARALLELED CONSISTENT RESULTS The Constant Chlor Plus MC4-50