!!! N3N Parts List!!! 2/15/2012!!!! FUSELAGE FIXED PARTS Fuselage Skeleton!!!!!!!!! COND! Frame structure (not complete) no carry through!!!!

Transcription

1 N3N Parts List 2/15/2012 FUSELAGE FIXED PARTS Fuselage Skeleton COND Frame structure (not complete) no carry through damgd Center Section Complete Carry Through Center Sec. assembled rebuilt Spar Carry Through Front new/used Rear new/used Wing Attach castings (4 reqd 2L 2R) used plates (8 reqd 4L 4R) used Master Wing Ribs Left as is Right as is Floors 1st station Paper pattern only 2nd station Paper pattern only 3rd station Paper pattern only Seats Front Pattern deposit Rear Pattern deposit 2 front support tubes long used 2 rear support tubes short used Bungee cord (w/your old ring- need 2) new Bungee cord (w/new ring - need 2) new Attach brackets Cabane struts left front N/A right front N/A left rear N/A right rear N/A Cabane wires Roll Wires (2 each) Flat Iron attach link (2 each) new Insodence wires 1/4 wire (2 each) N/A 5/16 wire (2 each) N/A Flying Wires Front (4) Rear (4) Landing Wires (4) some in stock Float Attach left Weldment (plated) used right Weldment used Outside step (2) new Inside step new left used right used 1

2 Gear Attach 1st Station fuselage attach Ball set right used left used 2nd Station attach link pair Tail Wheel Lower (2) upper 2 Attach pieces - Lower 1 attach piece - Upper Fuselage former (stamped channel Engine Compartment left upper used right upper used left lower used right lower used Replacement SS firewall w/holes (new) new Firewall panel attache pieces (curved angle) top engine side used top gas side used left engine side used left gas side used right engine side used right gas side used bottom engine side used bottom gas side used 1st Station Cabane covers right front used right center used right rear used left front used left center used left rear used Bottom 1st Station left gear cover used left straight used left L shape (2 piece) used right gear cover used right straight used right L shape (2 piece) used Bottom Panel Attach - Long left extrusion (2 & 3rd station) used right extrusion (2 & 3rd station) used Bottom Skin former (stamping) rear spar former used front spar former used left right center 2

3 Bottom Skin former (stamping) continued 2nd station former left used right used center used 3rd station former (FRONT SEAT) left used right used center used 3rd station former (REAR SEAT) left used right used center used 4th station former (FRONT SEAT) left used right used center used 4th station former (REAR SEAT) left used right used center used Fuselage-Skins Fairings & Covers Fairings and Covers Wing fairing left (5 different pieces) used Wing fairing right (5 different pieces) used Leading edge Wing Fairings left top used left bottom new right top used Leading Edge Screw covers left top N/A left bottom N/A right top N/A right bottom N/A Vertical and Horizontal Stabilizer Fairing used Horizontal Stabilizer Fairings Upper to vert. stabilizer left new right new Lower to fuselage left new right new Rudder strip left Pattern right Pattern 3

4 Elevator Bell crank covers left poor right poor Float Attach Screw covers left A Pattern left B right A right B Skins-Bottoms skins 1st station static air Pattern 2nd & 3rd station skin Pattern left inner Pattern left outer - long Pattern right inner Pattern right outer - long Pattern 4th station skin Pattern left front Pattern left rear Pattern right front Pattern left rear Pattern Fuselage Removable Panel Top Oil tank panel Left Engine access door panel Right Engine access door panel Bottom drain panel Gas Tank panel Lifting wire access panels: 1st station left side panel N/A 1st station right side panel 1st station bottom left right Bottom Center panels N/A on all of this front rear 2nd station panel 3rd station panel w/step door 4th station panel w/step door lift tube hole Rudder cable panel screw attach Front & rear cockpit cover screw attach N/A Tail wheel cover screw attach Nose Bowl (fiberglass mold) RENT/Deposit 4

5 Fuselage - controls Links to brake master cylinder front to rear (need 2) N/A front to master cylinder Automotive master cyl need 2 w/ss rods new bell crank bracket left front used right front used left rear used right rear used bell cranks left front N/A right front N/A left rear N/A right rear N/A Stick control need 2 front new rear new Complete torque tube unit w/sticks new without sticks tube front support bearing assy tube rear support bearing assy Elevator push tubes front to rear stick-big used rear support-big used front to rear stick-short rear support-short Aileron push tubes support to mechanical stick attach block new Aileron stops 2 each new Elevator bell crank used elevator attach bell crank w/bearings used Fuel System Fuel quantity assembly manual pumps need 2 N/A quantity gauges need 2 new not orig upper wing check valve need 1 used installation-operations manual used Fuel line to fuel pump N/A Wobble pump & fuel strainer as is rebuilt with strainer, new gasket, new packing Fuel line to fuel strainer N/A Fuel strainer & wobble pump attach bracket N/A Fuel line to carb N/A 5

6 Fuel system continued Fuel valve control linkage bearing support need 2 N/A Fuel line to valve shut off valve N/A Brackets to hold valve need 2 N/A Fuel valve control linkage 4 diff pieces N/A Fuel tank support pads need 4 N/A Fuel tank cap N/A Fuel tank support lower upper Overflow lines need 2 N/A NRA-7 carb as is used Major Aircraft parts Vertical Stabilizer - complete p r i c e d e p e n d s o n c o n d i t i o n Rudder attach bearing bracket Rudder - complete skeleton spar N/A ribs N/A bottom edge formed stamping N/A counter weight N/A trim tab N/A Left horizontal stab - complete skeleton spar N/A ribs N/A leading edge N/A left brace N/A Right horizontal stab - complete skeleton Price depends on condition spar N/A ribs N/A leading edge N/A right brace N/A Elevators - comp skeleton right/left left - left spar Price depends on condition left - rib left-leading edge N/A left-trim cover N/A left -trim tab flight adj pulley used push-pull rod used phenolic ware strip used right-right spar N/A? right - rib right-leading edge N/A right-trim cover N/A right-trim tab ground adjustable used trim tabs attach brackets 2 needed N/A 6

7 Electrical Fuse Box w/cover & fuse block used 1/2 conduit from front inst board to fuse box N/A 1/2 conduit front to rear cockpit N/A Glass fuse 6 each 5 spare N/A Triangle junction box need 2 used Electrical lines to tail 1/4 alum tubing to tail light N/A and mooring light Battery case: battery case holding bracket N/A flex conduit to battery case N/A conduit to main junction box from firewall N/A Tachometer tach generator used main junction box for elec tachs flex cable to front tach N/A flex cable to rear tach N/A tach indicators front N/A rear N/A Instrument board switches w/phosphorous tips N/A front need 4 N/A rear need 4 N/A Instrument board engraved switch plate need 2 new Instrument board rear switch cover box need 2 N/A Rheostat need 2 used cover box N/A front rear Instrument board light sockets N/A front need 2 rear need 2 Rheostat plaque new Instrument board light flex conduits need 4 N/A Flex conduit to compass front/rear need 2 N/A Mooring light assembly complete N/A bulb assembly N/A lense assembly Flexible conduit to mooring light Tail light assembly Tail light lense Flexible conduit to tail light 7

8 Gear Gear Assembly complete rebuilt w/new packing seals 4 needed set new main spring new outside nut bushing new inside nut bushing new BT axel used stock axel used Brace to fuselage need 2 used Reinforced crossover tube new Gear wired need 2 N/A Brake assembly w/shoes & spring need 2 used springs-red new springs-black new BT wheels need 2 N/A 27 tires need 2 N/A Tail wheel w/bearings bronze bushing & axel new tire N/A bearings N/A axel N/A Tail wheel lock assembly lock pin w/spring cap w/springs to center Tail wheel yoke assembly w/shock abs & tire cast woldment Shock absorber complete new spring/packing Other parts from original pattern Tail wheel boot canvas cover w/your ring new Front stick canvas boot new Rear stick canvas boot new Cockpit canvas cover new Engine canvas cover new Baggage canvas compartment new Map cases -front & rear used Wings Upper wing 34x5 skeleton dmgd Spars front rear Leading edge Trailing edge Ribs used Wing tip N/A left right Wings continued 8

9 Lifting cable box lift cable box door complete parts for lift cable lifting wire lifting cables N/A NAV lights assembly green lense red lense bulbs N/A Left aileron skeleton trim tab Right aileron trim tab 4 access plates Fuel gauge check valve used Lower left wing skeleton depends on condition Spars front rear Leading edge Trailing edge Ribs Removable wing tip dep on cond Aileron dep on cond Float attach brackets outboard need 2 inboard need 2 Lower right wing skeleton N/A Spars N/A front rear Leading edge Trailing edge Ribs Aileron dep on cond Removable wing tip dep on cond N struts need 2 Float attach outboard need 2 inboard need 2 Controls Throttle quadrant complete assy (orig) used Misc quad parts Front push pull rod w/bearing need 2 Rear push pull rod w/bearing need 2 Front Bell crank left right 9

10 Controls continued Front Bell crank bracket left right Rear Bell crank left right Rear Bell crank bracket left right Complete Rudder Pedal Assembly used front rear Rudder Pedal connecting rods 4 each Front set/brake pedal Front bell crank left -right Front bell brackets left-right Rear set/brake pedal Rear bell crank left-right Rear bell crank brackets left-right Switch Switch bracket Control rods (3 different lengths) Control rod bearing Front handle Rear handle Mag switch placard (2) Carb Heat Push pull tubes 2 each Push pull tube holding bracket Push pull tube handles 2 each Firewall bell crank Firewall bell crank bracket Sheath wire to carb heat box Sheath wire attach bracket Carb heat box w/doors Air intake tubes left new right new Carb heat collector ring used Carb heat duct tube to heat box tube clamp used Fire Extinguisher CO2 bottle CO2 bottle brackets 2 each Fire pull-assembly complete w/handles placard and bracket handles 2 each CO2 distribution ring engine compartment 3 pieces 1/2 lines to CO2 distribution ring 2 each 10

11 Fire Extinguisher continue CO2 cable to bottle 2 each Instrument Board - Front Blank instrument board 8 or 9 hole used Turn & bank Gyro Navy Fish Bowl Compass as is 3 in 1 gage (oil,gas press & oil temp) Fuel gage Fuel gage pump Clock Altimeter Receptacle w/cover door Switch plate w/printing new Switches w/phosphorous tips front 4 Switch box w/grommet Reostat cover box/grommet new Reostat placard Flex conduit to instrument board light compass light Instrument board light socket need 2 light socket attach nuts 2 light bulbs 2 Crash pad -Rear Blank instrument board 8 or 9 hole used Compass 3 in 1 gage (oil, gas press & oil temp) Fuel gage Fuel gage pump Clock Altimeter Engine Prime Receptacle w/cover door Switch plate w/printing new 4 switches Switch box Reostat box Reostat w/knob Crash pad paper Pattern for Instrument Board paper 11

12 12