DTC Summaries. V8 AJ26 Engine Management Refer to page 2 for important information regarding the use of this Summary.

Transcription

1 DTC Summaries V8 AJ26 Engine Management 1997 OBD II MONITORING CONDITIONS: When testing for DTC reoccurrence, it can be determined if the Service Drive Cycle was of sufficient length by performing a PDU Systems Readiness Test. The Systems Readiness Test occurs automatically when DTC retrieval is initiated. If DTC P1000 is stored in memory, the on-board diagnostic tests have not been completed. If DTC P1111 is stored in memory, all on-board diagnostic tests have been completed. To identify which portions of the Systems Readiness Test have not been completed, access OBD Logger from PDU Toolbox. PDU will report in the following manner: Module ECM: The following tests have been identified as incomplete: Catalyst Evaporative purge system O2 Sensor EGR system Refer to page 2 for important information regarding the use of this Summary. Engine Management: V8 AJ

2 NOTES MONITORING CONDITIONS OBD II SERVICE DRIVE CYCLE For the particular DTC. Operate the vehicle as described to check for a reoccurrence of the DTC. Y YES indicates that the DTC is an OBD II DTC. N NO indicates that the DTC is a non OBD II DTC. CHECK ENGINE MIL 1 1 TRIP indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE TRIP. (CK ENG) 2 2 TRIPS indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE TRIPS. N NO indicates that the CHECK ENGINE MIL is not activated OTHER DEFAULT ACTION POSSIBLE CAUSES N None 1 1 TRIP to activate indicator(s). 2 2 CONSECUTIVE TRIPS to activate indicator(s). R RED MIL A AMBER MIL M MESSAGE ECM default action; Logged DTC stored in memory buffer; Flagged DTC stored in memory / CHECK ENGINE MIL activated. HIGH VOLTAGE High voltage can be either EMS sensor supply voltage (5 volt) or B+ voltage. REFERENCE: It is recommended that the applicable Electrical Guide be referenced when using the information contained in this document. Engine Management: V8 AJ

3 PDU DATALOGGER ACRONYMS ACCREQ ACHPS ACLPS ADV BARO BAT1+ CLV CRANKREQ CRUISEA CRUISEB CRUISEC CRUISED CRUISEO CRUISER CRUISES CRUISEC1 DTC1 DTCS ECT EGR EVAP FANF FANFRLY FANS FANSRLY FBRAKE2 A/C compressor clutch request A/C refrigerant high pressure switch A/C refrigerant low pressure switch Ignition timing advance (Cyl 1, A bank) Barometric pressure sensor Battery B+ supply to ECM Calculated load value Crank request (from BPM) Cruise control accel / decel switch Cruise resume / cancel switch Cruise cancel switch Cruise control set / inch / decel switch Cruise control ON / OFF switch Cruise control resume switch Cruise control set / inch / accel switch Cruise control cancel switch Number of DTCs logged this trip Number of permanent DTCs logged Engine coolant temperature Exhaust gas recirculation Evaporative emission system monitor Cooling fan fast Cooling fan relay fast Cooling fan slow Cooling fan relay slow Brake switch FP FPRLY GUARD1 O2SB1D O2SB2D HO2SB1U HO2SB2U HTDSC IAT KS1A KS1B KS4A KS4B KSFA KSFB LTFT1 LTFT2 MAF MAFGND1 MAFS1 MPROBE PKBRAKE PNPS Fuel pump Fuel pump relay Mechanical guard sensor Oxygen sensor (downstream) A bank Oxygen sensor (downstream) B bank Heated oxygen sensor (upstream) A bank Heated oxygen sensor (upstream) B bank Heated windshield request Intake air temperature Knock sensor 1 A bank Knock sensor 1 B bank Knock sensor 4 A bank Knock sensor 4 B bank Knock sensor fail A bank Knock sensor fail B bank Long term fuel trim A bank Long term fuel trim B bank Mass air flow MAFS ground Mass air flow sensor Measurement probe (RED) Park brake switch Park / neutral position switch (rotary switch) PPS1 Pedal position sensor track A PPS2 Pedal position sensor track B RPM Engine speed SPS Sensor power supply monitor STFT1 Short term fuel trim A bank STFT2 Short term fuel trim B bank STFTB1D Short term fuel trim A bank downstream STFTB1U Short term fuel trim A bank upstream STFTB2D Short term fuel trim B bank downstream STFTB2U Short term fuel trim B bank upstream TPS Throttle position sensor TPS1 Throttle position sensor track 1 TPS2 Throttle position sensor track 2 TTP Target throttle position VSS Vehicle speed VSVRM Vacuum switching valve release monitor VSVAM Vacuum switching valve atmosphere monitor VSVVM Vacuum switching valve vacuum monitor VVTBM Variable valve timing (B bank) monitor Engine Management: V8 AJ

4 P0101 MAFS range / performance Engine at normal operating temperature; Y 2 2 When CK ENG MIL is activated Blocked air cleaner drive mph (70 95 km/h); [A, M] (DTC flagged; second trip), ECM: Air intake leak rpm; > 10 seconds Substitutes throttle angle for Engine breather leak engine load measurement Throttle control malfunction (TPS) Limits engine speed to 3000 rpm MAFS to ECM sensing circuit high resistance Inhibits canister purge MAFS to ECM sensing circuit intermittent Inhibits EGR short circuit to ground MAFS supply circuit high resistance MAFS failure P0102 MAFS sense circuit low voltage Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated Blocked air filter [A, M] (DTC logged; first trip), ECM: MAFS to ECM sensing circuit high resistance or Substitutes throttle angle for open circuit engine load measurement MAFS to ECM sensing circuit intermittent Limits engine speed to 3000 rpm short circuit to ground Inhibits canister purge MAFS supply circuit open circuit or short circuit Inhibits EGR to ground MAFS failure P0103 MAFS sense circuit high voltage Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated MAFS to ECM reference ground circuit [A, M] (DTC logged; first trip), ECM: open circuit Substitutes throttle angle for MAFS to ECM sensing circuit short circuit to engine load measurement high voltage Limits engine speed to 3000 rpm MAFS failure Inhibits canister purge Inhibits EGR P0106 BARO circuit low voltage Ignition ON > 5 seconds Y 2 N None BARO failure (internal ECM fault) P0107 BARO circuit high voltage Ignition ON > 5 seconds Y 2 N None BARO failure (internal ECM fault) Engine Management: V8 AJ

5 P0111 IATS range / performance Engine idle > 40 seconds Y 2 N When CK ENG MIL is activated Blocked air cleaner (DTC flagged; second trip), ECM: Air intake leak Substitutes fixed temperature of Engine breather leak 50 C (122 F) IATS to ECM wiring open circuit or high resistance IATS to ECM sensing circuit short circuit to high voltage IATS failure P0112 IATS sense circuit high voltage Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), IATS to ECM wiring open circuit or high resistance (low air temperature) ECM: IATS to ECM sensing circuit short circuit to Substitutes fixed temperature of high voltage 50 C (122 F) IATS failure P0113 IATS sense circuit low voltage Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), IATS to ECM wiring short circuit to ground (high air temperature) ECM: IATS failure Substitutes fixed temperature of 50 C (122 F) P0116 ECTS range / performance Engine coolant temperature ambient; Y 2 2 When CK ENG MIL is activated Low coolant level start engine; [A, M] (DTC flagged; second trip), ECM: Contaminated coolant drive at normal operating temperature Substitutes transmission fluid Engine thermostat failure > 13 mph (20 km/h) > 3 minutes temperature (via CAN) ECTS to ECM sensing circuit high resistance Limits engine speed to 3000 rpm when hot Inhibits canister purge ECTS to ECM sensing circuit intermittent Inhibits EGR high resistance Inhibits VVT ECTS failure P0117 ECTS sense circuit high voltage Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated ECTS disconnected (low coolant temperature) [A, M] (DTC logged; first trip), ECM: ECTS to ECM sensing circuit high resistance, Substitutes transmission fluid open circuit or short circuit to high voltage temperature (via CAN) ECTS failure Limits engine speed to 3000 rpm Inhibits canister purge Inhibits EGR Inhibits VVT Engine Management: V8 AJ

6 P0118 ECTS sense circuit low voltage Ignition ON > 5 seconds Y 2 1 Refer to P0117 Default Action Engine overheat condition (high coolant temperature) [A, M] ECTS to ECM wiring short circuit to ground ECTS failure P0121 TPS circuit range / performance Ignition ON > 5 seconds Y 2 1 When RED MIL is activated TPS to ECM wiring open circuit or high resistance [R, M] (DTC logged; first trip), ECM: TPS to ECM sensing circuits ( 1 or 2 ) Defaults throttle to mechanical short circuit to high voltage guard mode TPS failure Inhibits idle speed control Inhibits cruise control Inhibits traction control / stability control Inhibits power limiting P0122 TPS circuit 1 low voltage Ignition ON > 5 seconds Y 2 1 Refer to P0121 Default Action TPS to ECM sensing circuit 1 (TPS pin 3) [R, M] open circuit or high resistance TPS failure P0123 TPS circuit 1 high voltage Ignition ON > 5 seconds Y 2 1 Refer to P0121 Default Action TPS to ECM sensing circuit 1 (TPS pin 3) [R, M] short circuit to high voltage TPS failure P0125 ECTS response Engine coolant temperature ambient; Y 2 1 When CK ENG MIL is activated Low coolant level (for closed loop fuel control) start engine; run engine to > 60 C [A, M] (DTC flagged; second trip), ECM: Contaminated coolant (140 F) > 2 minutes Substitutes transmission fluid Engine thermostat failure temperature (via CAN) ECTS to ECM sensing circuit high resistance, Limits engine speed to 3000 rpm open circuit or short circuit to high voltage Inhibits canister purge Inhibits EGR Inhibits VVT P0131 HO2S sense circuit low voltage Engine at normal operating temperature; Y 2 N None HO2S disconnected A bank, upstream (1) drive at steady speed > 40 mph (60 km/h); HO2S to ECM wiring open circuit engine speed rpm HO2S short circuit to ground > 1 minute 20 seconds HO2S failure Engine Management: V8 AJ

7 P0132 HO2S sense circuit high voltage Engine at normal operating temperature; Y 2 N None HO2S sensing circuit short circuit to high voltage A bank, upstream (1) drive at steady speed > 3 mph (4 km/h) HO2S ground (BRD braided shield) open circuit HO2S failure P0133 HO2S sense circuit slow Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated Engine misfire response A bank, upstream (1) drive at mph ( km/h); (DTC flagged; second trip), ECM: HO2S disconnected engine speed rpm Inhibits A bank closed loop HO2S mechanical damage >10 seconds HO2S to ECM wiring intermittent open circuit Inhibits A bank adaptive HO2S sensing circuit short circuit to high voltage HO2S short circuit to ground HO2S ground (BRD braided shield) open circuit HO2S heater circuit fault Exhaust leak Low exhaust temperature Injector flow partially blocked Catalyst efficiency decrease HO2S failure P0135 HO2S heater circuit malfunction Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated HO2S disconnected A bank, upstream (1) drive at steady speed > 20 mph (30 km/h) (DTC flagged; second trip), ECM: HO2S heater power supply open circuit Inhibits A bank closed loop HO2S heater to ECM wiring short circuit or open circuit Inhibits A bank adaptive HO2S heater failure Inhibits A bank downstream O2S control P0137 O2S sense circuit low voltage Ambient temperature < 70 C (158 F); Y 2 N None O2S disconnected A bank, downstream (2) engine at normal operating temperature; O2S to ECM wiring open circuit drive at steady speed > 13 mph (20 km/h) O2S short circuit to ground > 1 minute 10 seconds O2S failure P0138 O2S sense circuit high voltage Ambient temperature < 70 C (158 F); Y 2 N None O2S sensing circuit short circuit to high voltage A bank, downstream (2) engine at normal operating temperature; O2S ground (BRD braided shield) open circuit drive at steady speed > 13 mph (20 km/h) O2S failure > 1 minute 10 seconds Engine Management: V8 AJ

8 P0140 O2S sense circuit no activity Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated O2S disconnected A bank, downstream (2) drive > 13 mph (20 km/h); (DTC flagged; second trip), ECM: O2S mechanical damage engine speed > 1500 rpm; > 1 minute Inhibits A bank downstream O2S to ECM wiring open circuit O2S control O2S sensing circuit short circuit to high voltage O2S short circuit to ground O2S ground (BRD braided shield) open circuit Exhaust leak Low exhaust temperature O2S failure P0151 HO2S sense circuit low voltage Engine at normal operating temperature; Y 2 N None HO2S disconnected B bank, upstream (1) drive at steady speed > 40 mph (60 km/h); HO2S to ECM wiring open circuit engine speed rpm HO2S short circuit to ground > 1 minute 20 seconds HO2S failure P0152 HO2S sense circuit high voltage Engine at normal operating temperature; Y 2 N None HO2S sensing circuit short circuit to high voltage B bank, upstream (1) drive at steady speed > 3 mph (4 km/h) HO2S ground (BRD braided shield) open circuit HO2S failure P0153 HO2S sense circuit slow Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated Engine misfire response B bank, upstream (1) drive at mph ( km/h); (DTC flagged; second trip), ECM: HO2S disconnected engine speed rpm Inhibits B bank closed loop HO2S mechanical damage >10 seconds HO2S to ECM wiring intermittent open circuit Inhibits B bank adaptive HO2S sensing circuit short circuit to high voltage HO2S short circuit to ground HO2S ground (BRD braided shield) open circuit HO2S heater circuit fault Exhaust leak Low exhaust temperature Injector flow partially blocked Catalyst efficiency decrease HO2S failure Engine Management: V8 AJ

9 P0155 HO2S heater circuit malfunction Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated HO2S disconnected B bank, upstream (1) drive at steady speed > 20 mph (30 km/h) (DTC flagged; second trip), ECM: HO2S heater power supply open circuit Inhibits B bank closed loop HO2S heater to ECM wiring short circuit or open circuit Inhibits B bank adaptive HO2S heater failure Inhibits B bank downstream O2S control P0157 O2S sense circuit low voltage Ambient temperature < 70 C (158 F); Y 2 N None O2S disconnected B bank, downstream (2) engine at normal operating temperature; O2S to ECM wiring open circuit drive at steady speed > 13 mph (20 km/h) O2S short circuit to ground > 1 minute 10 seconds P0158 O2S sense circuit high voltage Ambient temperature < 70 C (158 F); Y 2 N None O2S sensing circuit short circuit to high voltage B bank, downstream (2) engine at normal operating temperature; O2S ground (BRD braided shield) open circuit drive at steady speed > 13 mph (20 km/h) O2S failure > 1 minute 10 seconds P0160 O2S sense circuit no activity Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated O2S disconnected B bank, downstream (2) drive > 13 mph (20 km/h); (DTC flagged; second trip), ECM: O2S mechanical damage engine speed > 1500 rpm; > 1 minute Inhibits B bank downstream O2S to ECM wiring open circuit O2S control O2S sensing circuit short circuit to high voltage O2S short circuit to ground O2S ground (BRD braided shield) open circuit Exhaust leak Low exhaust temperature O2S failure Engine Management: V8 AJ

10 P0171 A bank combustion too lean Engine at normal operating temperature; Y 2 2 When CK ENG MIL is activated Engine misfire drive at steady speed > 40 mph; [A, M] (DTC flagged; second trip), ECM: Air intake leak between MAFS and throttle engine speed rpm Inhibits downstream O2S control Fuel filter, system blockage > 1 minute 20 seconds Fuel injector blockage If DTC P0174 is also flagged, ECM: Fuel pressure regulator failure (low fuel pressure) Limits engine speed to 3000 rpm Low fuel pump output Inhibits canister purge* HO2S harness wiring condition fault Inhibits EGR Exhaust leak (before catalyst) ECM receiving incorrect signal from * Inhibited when lean fault is one or more of the following components: first detected ECTS, MAFS, IATS, TPS P0172 A bank combustion too rich Engine at normal operating temperature; Y 2 2 When CK ENG MIL is activated Blocked air filter drive at steady speed > 40 mph; [A, M] (DTC flagged; second trip), ECM: Fuel system return blockage engine speed rpm Inhibits downstream O2S control Leaking fuel injector(s) > 1 minute 20 seconds Fuel pressure regulator failure (high fuel pressure) If DTC P0175 is also flagged, ECM: ECM receiving incorrect signal from Limits engine speed to 3000 rpm one or more of the following components: Inhibits canister purge ECTS, MAFS, IATS, TPS Inhibits EGR P0174 B bank combustion too lean Engine at normal operating temperature; Y 2 2 When CK ENG MIL is activated Engine misfire drive at steady speed > 40 mph; [A, M] (DTC flagged; second trip), ECM: Air intake leak between MAFS and throttle engine speed rpm Inhibits downstream O2S control Fuel filter, system blockage > 1 minute 20 seconds Fuel injector blockage If DTC P0171 is also flagged, ECM: Fuel pressure regulator failure (low fuel pressure) Limits engine speed to 3000 rpm Low fuel pump output Inhibits canister purge* HO2S harness wiring condition fault Inhibits EGR Exhaust leak (before catalyst) ECM receiving incorrect signal from * Inhibited when lean fault is one or more of the following components: first detected ECTS, MAFS, IATS, TPS Engine Management: V8 AJ

11 P0175 B bank combustion too rich Engine at normal operating temperature; Y 2 2 When CK ENG MIL is activated Blocked air filter drive at steady speed > 40 mph; [A, M] (DTC flagged; second trip), ECM: Fuel system return blockage engine speed rpm Inhibits downstream O2S control Leaking fuel injector(s) > 1 minute 20 seconds Fuel pressure regulator failure (high fuel pressure) If DTC P0172 is also flagged, ECM: ECM receiving incorrect signal from Limits engine speed to 3000 rpm one or more of the following components: Inhibits canister purge ECTS, MAFS, IATS, TPS Inhibits EGR P0201 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 When CK ENG MIL is activated Injector disconnected cylinder A1 (1) run engine > 30 seconds; [A, M] (DTC flagged; second trip), ECM: Injector harness wiring open or short circuit engine speed rpm Limits engine speed to 3000 rpm Injector failure Inhibits canister purge Inhibits EGR If DTCs for all A bank injectors are flagged: Inhibits A bank closed loop Inhibits A bank adaptive Inhibits A bank downstream O2S control P0202 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0201 Default Action Injector disconnected cylinder A2 (2) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure P0203 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0201 Default Action Injector disconnected cylinder A3 (3) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure P0204 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0201 Default Action Injector disconnected cylinder A4 (4) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure Engine Management: V8 AJ

12 P0205 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 When CK ENG MIL is activated Injector disconnected cylinder B1 (5) run engine > 30 seconds; [A, M] (DTC flagged; second trip), ECM: Injector harness wiring open or short circuit engine speed rpm Limits engine speed to 3000 rpm Injector failure Inhibits canister purge Inhibits EGR If DTCs for all B bank injectors are flagged: Inhibits B bank closed loop Inhibits B bank adaptive Inhibits B bank downstream O2S control P0206 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0205 Default Action Injector disconnected cylinder B2 (6) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure P0207 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0205 Default Action Injector disconnected cylinder B3 (7) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure P0208 Fuel injector circuit malfunction Engine at normal operating temperature; Y 2 1 Refer to P0205 Default Action Injector disconnected cylinder B4 (8) run engine > 30 seconds; [A, M] Injector harness wiring open or short circuit engine speed rpm Injector failure Engine Management: V8 AJ

13 P0222 TPS circuit 2 low voltage Ignition ON > 5 seconds Y 2 1 When RED MIL is activated TPS to ECM sensing circuit 2 (TPS pin 2) [R, M] (DTC logged; first trip), ECM: open circuit or high resistance Defaults throttle to mechanical TPS failure guard mode Inhibits idle speed control Inhibits cruise control Inhibits traction control / stability control Inhibits power limiting P0223 TPS circuit 2 high voltage Ignition ON > 5 seconds Y 2 1 Refer to P0222 Default Action TPS to ECM sensing circuit 2 (TPS pin 2) [R, M] short circuit to high voltage TPS failure P0300 Random misfire detected Engine at idle, or steady between Y 1 or 2 1 When CK ENG MIL is activated Cylinder compression low rpm; > 2 minutes 30 seconds ** [A, M] (DTC flagged; second trip), ECM: Worn camshaft / broken valve spring(s) Limits engine speed to 3000 rpm Fuel delivery pressure (low / high) Inhibits closed loop Fuel injector(s) blocked / leaking Fuel injector(s) continuously open Inhibits adaptive Fuel contamination Inhibits canister purge Fuel injector circuit fault(s) Inhibits EGR (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition module primary circuit fault(s) (Cylinder misfire detected DTC also flagged) Ignition module to ignition coil primary circuit fault(s) (Cylinder misfire detected DTC also flagged) Ignition module ground circuit open circuit, high resistance Ignition coil failure Ignition module failure ** If, on the first trip, the misfire is severe enough to cause excess exhaust emission, individual cylinder DTC plus DTC P1316 will be flagged; CHECK ENGINE MIL will flash. If, on the first trip, the misfire is severe enough to cause catalyst damage, individual cylinder DTC plus DTC P1313 (A bank) or P1314 (B bank) will be flagged; CHECK ENGINE MIL will flash. Engine Management: V8 AJ

14 P0301 Misfire detected cylinder A1 (1) Engine at idle, or steady between Y 1 or 2 1 When CK ENG MIL is activated Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] (DTC flagged; second trip), ECM: Limits engine speed to 3000 rpm Inhibits A bank closed loop Inhibits A bank adaptive Inhibits canister purge Inhibits EGR P0302 Misfire detected cylinder A2 (2) Engine at idle, or steady between Y 1 or 2 1 Refer to P0301 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] P0303 Misfire detected cylinder A3 (3) Engine at idle, or steady between Y 1 or 2 1 Refer to P0301 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] P0304 Misfire detected cylinder A4 (4) Engine at idle, or steady between Y 1 or 2 1 Refer to P0301 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] P0305 Misfire detected cylinder B1 (5) Engine at idle, or steady between Y 1 or 2 1 When CK ENG MIL is activated Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] (DTC flagged; second trip), ECM: Limits engine speed to 3000 rpm Inhibits B bank closed loop Inhibits B bank adaptive Inhibits canister purge Inhibits EGR P0306 Misfire detected cylinder B2 (6) Engine at idle, or steady between Y 1 or 2 1 Refer to P0305 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] P0307 Misfire detected cylinder B3 (7) Engine at idle, or steady between Y 1 or 2 1 Refer to P0305 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] P0308 Misfire detected cylinder B4 (8) Engine at idle, or steady between Y 1 or 2 1 Refer to P0305 Default Action Refer to P0300 Possible Faults rpm; > 2 minutes 30 seconds ** [A, M] ** If, on the first trip, the misfire is severe enough to cause excess exhaust emission, individual cylinder DTC plus DTC P1316 will be flagged; CHECK ENGINE MIL will flash. If, on the first trip, the misfire is severe enough to cause catalyst damage, individual cylinder DTC plus DTC P1313 (A bank) or P1314 (B bank) will be flagged; CHECK ENGINE MIL will flash. Engine Management: V8 AJ

15 P0327 KS sense circuit out of range Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), ECM: Poor sensor contact with the cylinder block (low voltage) A bank Sets ignition retard to maximum KS to ECM sense circuit short circuit to ground KS failure P0328 KS sense circuit out of range Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), ECM: Poor sensor contact with the cylinder block (high voltage) A bank Sets ignition retard to maximum KS to ECM sense circuit high resistance or open circuit KS to ECM sense circuit short circuit to high voltage KS failure P0332 KS sense circuit out of range Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), ECM: Poor sensor contact with the cylinder block (low voltage) B bank Sets ignition retard to maximum KS to ECM sense circuit short circuit to ground KS failure P0333 KS sense circuit out of range Ignition ON > 5 seconds Y 2 N When DTC is logged (first trip), ECM: Poor sensor contact with the cylinder block (high voltage) B bank Sets ignition retard to maximum KS to ECM sense circuit high resistance or open circuit KS to ECM sense circuit short circuit to high voltage KS failure P0335 CKPS circuit malfunction Crank engine > 5 seconds engine will not Y 2 N None CKPS disconnected start; or start engine, run steady > 1000 rpm; CKPS gap incorrect / foreign matter on sensor face or engine stall, ignition ON CKPS sensing circuit open circuit, short circuit to ground, short circuit to high voltage CKPS failure P0340 CMPS circuit malfunction Crank engine > 5 seconds Y 2 N When fault is detected, ECM: CMPS disconnected Guesses camshaft position CMPS gap incorrect / foreign matter on (engine starts 50% of time sensor face rough running) CMPS sensing circuit open circuit, short circuit to ground, short circuit to high voltage CMPS failure Engine Management: V8 AJ

16 P0351 Ignition coil (A1) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 When fault is detected, ECM: ECM to ignition module primary circuit secondary circuit malfunction [A, M] Inhibits individual cylinder open circuit, short circuit to ground, fuel injection high resistance Inhibits A bank closed loop Ignition module to ignition coil primary circuit open circuit, short circuit to ground, Inhibits A bank downstream high resistance O2S control Ignition module ground circuit open circuit, high resistance Ignition coil failure Ignition module failure P0352 Ignition coil (A2) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0351 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] P0353 Ignition coil (A3) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0351 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] P0354 Ignition coil (A4) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0351 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] P0355 Ignition coil (B1) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 When fault is detected, ECM: Refer to P0351 Possible Causes secondary circuit malfunction [A, M] Inhibits individual cylinder fuel injection Inhibits B bank closed loop Inhibits B bank downstream O2S control P0356 Ignition coil (B2) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0355 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] P0357 Ignition coil (B3) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0355 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] P0358 Ignition coil (B4) primary / Run engine steady < 3000 rpm > 5 seconds Y 2 1 Refer to P0355 Default Action Refer to P0351 Possible Causes secondary circuit malfunction [A, M] Engine Management: V8 AJ

17 P0400 EGR flow malfunction Engine at normal operating temperature; Y 2 N None EGR valve connector pins high resistance normal, varied driving for 3 minutes; then EGR pipe / exhaust manifold leak decel. / accel mph (80 95 km/h), EGR pipe blocked within 6 seconds between rpm EGR valve stuck open / closed, blocked EGR valve failure P0405 EGR drive circuits open circuit Ignition ON > 5 seconds Y 2 N None EGR valve power supply circuit open circuit EGR valve to ECM drive circuit pair EGR pins 1/3, 4/6 open circuit, high resistance EGR valve failure (stepper motor open circuit) P0406 EGR drive circuits short circuit Ignition ON > 5 seconds Y 2 N When fault is detected, ECM: EGR valve to ECM drive circuit pair EGR pins Inhibits EGR 1/3, 4/6 short circuit to ground or high voltage EGR valve failure (stepper motor short circuit) P0420 Catalyst efficiency below Ambient (IATS) temperature Y 2 N None HO2S / O2S disconnected threshold A bank > 20 C (68 F); HO2S / O2S to ECM wiring fault engine at normal operating temperature; HO2S heater to ECM wiring fault normal, varied driving for 3 minutes; HO2S heater failure then, constant steady throttle mph Upstream HO2S failure (80 95 km/h), rpm Downstream O2S failure > 15 seconds; Catalyst failure then, constant steady throttle mph (50 60 km/h), rpm > 15 seconds P0430 Catalyst efficiency below Ambient (IATS) temperature Y 2 N None HO2S / O2S disconnected threshold B bank > 20 C (68 F); HO2S / O2S to ECM wiring fault engine at normal operating temperature; HO2S heater to ECM wiring fault normal, varied driving for 3 minutes; HO2S heater failure then, constant steady throttle mph Upstream HO2S failure (80 95 km/h), rpm Downstream O2S failure > 15 seconds; Catalyst failure then, constant steady throttle mph (50 60 km/h), rpm > 15 seconds Engine Management: V8 AJ

18 P0441 EVAP system incorrect Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated EVAPP to ECM drive circuit open circuit, purge flow vehicle stationary; brakes applied; (DTC flagged; second trip), ECM: short circuit, high resistance gear D ; idle > 10 minutes (from engine Inhibits adaptive EVAPP power supply circuit open circuit start); fuel tank > 1/4 full Inhibits canister purge EVAPP to engine purge pipe damaged / blocked / leaking EVAPP operating vacuum hose leak / blockage EVAPP failure P0444 EVAPP valve circuit open circuit Engine at normal operating temperature; Y 2 N Refer to P0441 Default Action EVAPP to ECM drive circuit open circuit or vehicle stationary; brakes applied; high resistance gear D ; idle > 10 seconds EVAPP failure P0445 EVAPP valve circuit short circuit Engine at normal operating temperature; Y 2 N Refer to P0441 Default Action EVAPP to ECM drive circuit short circuit to ground vehicle stationary; brakes applied; EVAPP failure gear D ; idle > 10 seconds P0460 Fuel level sense signal Drive > 30 miles (48 km) Y 2 N None Fuel level sensor to instrument pack circuits performance intermittent short or open circuit, high resistance Fuel level sensor failure Instrument pack fault (incorrect fuel level data) P0506 Idle rpm lower than expected Engine at normal operating temperature; Y 2 N None Air intake blockage transmission at normal operating Accessory drive overload (defective / seized temperature; gear N ; component) idle > 1 minute 40 seconds (no electrical Throttle valve stuck closed load, A/C compressor, radiator fans, brake Throttle assembly failure pedal switching during period) P0507 Idle rpm higher than expected Engine at normal operating temperature; Y 2 N None Intake air leak between MAFS and throttle transmission at normal operating Intake air leak between throttle and engine temperature; gear N ; Engine breather leak idle > 1 minute 40 seconds (no electrical Cruise control vacuum failure load, A/C compressor, radiator fans, brake Throttle valve stuck open pedal switching during period) Throttle assembly failure Engine Management: V8 AJ

19 P0560 Vehicle voltage malfunction Ignition ON > 35 seconds Y 2 N None ECM battery power supply open circuit, high resistance ECM ignition power supply open circuit, high resistance P0566 Cruise control CANCEL switch Ignition ON > 75 seconds N N 1 When fault is detected, ECM: Cruise control switches internal steering wheel ON fault [A, M] Inhibits cruise control short circuit to ground Steering wheel cassette reel short circuit to ground Cassette reel to ECM circuit short circuit to ground CANCEL switch failure (stuck ON) P0567 Cruise control RESUME switch Ignition ON > 75 seconds N N 1 When fault is detected, ECM: Cruise control switches internal steering wheel ON fault [A, M] Inhibits cruise control short circuit to ground Steering wheel cassette reel short circuit to ground Cassette reel to ECM circuit short circuit to ground RESUME switch failure (stuck ON) P0568 Cruise control switch Ignition ON > 5 seconds N N 1 When fault is detected, ECM: Cruise control switches internal steering wheel ground malfunction [A, M] Inhibits cruise control open circuit Steering wheel cassette reel open circuit or high resistance Cassette reel to ECM circuit (ACCEL / DECEL) open circuit or high resistance ACCEL / DECEL switch failure P0569 Cruise control DECEL / SET Ignition ON > 10 minutes N N 1 When fault is detected, ECM: Cruise control switches internal steering wheel (SET-) switch ON fault [A, M] Inhibits cruise control short circuit to ground Steering wheel cassette reel short circuit to ground Cassette reel to ECM circuit short circuit to ground DECEL / set switch failure (stuck ON) Engine Management: V8 AJ

20 P0570 Cruise control ACCEL / SET Ignition ON > 10 minutes N N 1 When fault is detected, ECM: Cruise control switches internal steering wheel (SET+) switch ON fault [A, M] Inhibits cruise control short circuit to ground Steering wheel cassette reel short circuit to ground Cassette reel to ECM circuit short circuit to ground ACCEL / set failure (stuck ON) P0603 ECM data corrupted Ignition ON > 5 seconds Y 1 N None ECM failure P1000 System checks not complete System Readiness Test N N N None See page 1 since last memory clear P1104 MAFS ground malfunction Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated MAFS to ECM reference ground circuit [A, M] (DTC logged; first trip), ECM: open circuit, short circuit to high voltage, Substitutes throttle angle for high resistance engine load measurement MAFS to ECM sensing circuit open circuit Limits engine speed to 3000 rpm MAFS failure Inhibits canister purge Inhibits EGR P1111 System checks complete System Readiness Test N N N None See page 1 since last memory clear P1121 Pedal position sensor circuit A Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit A range / performance [A, M] (sensor pin 5) open circuit, short circuit or high resistance Sensor power supply fault Sensor reference ground fault Pedal position sensor failure P1122 Pedal position sensor circuit A Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit A low voltage [A, M] (sensor pin 5) wire open circuit or high resistance Sensor power supply fault Pedal position sensor failure Engine Management: V8 AJ

21 P1123 Pedal position sensor circuit A Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit A high voltage [A, M] (sensor pin 5) wire short circuit to high voltage Pedal position sensor failure P1221 Pedal position sensor circuit B Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit B range / performance [A, M] (sensor pin 3) open circuit, short circuit or high resistance Sensor power supply fault Sensor reference ground fault Pedal position sensor failure P1222 Pedal position sensor circuit B Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit B low voltage [A, M] (sensor pin 3) wire open circuit or high resistance Sensor power supply fault Pedal position sensor failure P1223 Pedal position sensor circuit B Ignition ON > 5 seconds N N 1 None Pedal position sensor to ECM sense circuit B high voltage [A, M] (sensor pin 3) wire short circuit to high voltage Pedal position sensor failure P1224 Throttle control position error Ignition ON > 3 minutes Y 2 1 When RED MIL is activated Throttle adaptions not performed after [R, M] (DTC logged; first trip), ECM: battery disconnect Defaults throttle to TPS disconnected mechanical guard mode TPS to ECM sense circuits open circuit, Inhibits idle speed control high resistance Inhibits cruise control Throttle motor power relay failure Inhibits traction control / Throttle motor power relay to ECM circuit fault stability control Throttle motor power relay power supply Inhibits power limiting open circuit ECM ground circuit fault (relay coil drive) Throttle motor to ECM drive circuits open circuit, short circuit, high resistance Throttle motor failure Throttle assembly failure Engine Management: V8 AJ

22 P1226 Mechanical guard sensor Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated Mechanical guard sensor to ECM sense circuit range / performance [A, M] (DTC logged; first trip), ECM: open circuit, short circuit or high resistance Inhibits cruise control Sensor power supply fault Sensor reference ground fault Mechanical guard sensor failure Mechanical guard actuator seized / spring broken P1227 Mechanical guard sensor circuit Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated Mechanical guard sensor to ECM sense circuit low voltage [A, M] (DTC logged; first trip), ECM: open circuit or high resistance Inhibits cruise control Sensor power supply fault Mechanical guard sensor failure P1228 Mechanical guard sensor circuit Ignition ON > 5 seconds Y 2 1 When AMBER MIL is activated Mechanical guard sensor to ECM sense circuit high voltage [A, M] (DTC logged; first trip), ECM: short circuit to high voltage Inhibits cruise control Mechanical guard sensor failure P1229 Throttle motor control circuit Ignition ON > 5 seconds Y 2 1 When RED MIL is activated Throttle motor disconnected malfunction [R, M] (DTC logged; first trip), ECM: Throttle motor to ECM drive circuits short circuit Defaults throttle to or open circuit mechanical guard mode Throttle motor failure Inhibits idle speed control Inhibits cruise control Inhibits traction control / stability control Inhibits power limiting P1230 Fuel pump relay malfunction Ignition ON > 5 seconds Y 2 N None Fuel pump relay failure Fuel pump relay to ECM circuit fault Fuel pump relay coil power supply open circuit ECM ground circuit fault (relay coil drive) P1235 VSV 1 circuit range / performance Drive with cruise control engaged N N 1 When fault is detected, ECM: Vacuum leak / blockage between the throttle (mechanical guard position) > 15 seconds [A, M] Inhibits cruise control elbow and the throttle vacuum actuator Vacuum actuator failure Mechanical guard actuator seized / spring broken Engine Management: V8 AJ

23 P1236 VSV 1 (vacuum) circuit failure Ignition ON > 5 seconds N N 1 When fault is detected, ECM: VSV 1 disconnected [A, M] Inhibits cruise control VSV 1 to ECM drive circuit high resistance, open circuit or short circuit VSV 1 power supply open circuit VSV 1 failure P1237 VSV 2 (atmosphere) circuit failure Ignition ON > 5 seconds N N 1 When fault is detected, ECM: VSV 2 disconnected [A, M] Inhibits cruise control VSV 2 to ECM drive circuit high resistance, open circuit or short circuit VSV 2 power supply open circuit VSV 2 failure P1238 VSV 3 (release) circuit failure Ignition ON > 5 seconds N N 1 When fault is detected, ECM: VSV 3 disconnected [A, M] Inhibits cruise control VSV 3 to ECM drive circuit high resistance, open circuit or short circuit VSV 3 ground circuit fault VSV 3 failure P1240 Sensor reference voltage Ignition ON > 5 seconds Y 2 1 When RED MIL is activated ECM to throttle sensors reference voltage circuit malfunction (TPS, pedal position [R, M] (DTC logged; first trip), ECM: short circuit to ground, short circuit to and mechanical guard sensors) Defaults throttle to high voltage, open circuit, high resistance (ECM pins EM10-21, EM11-8) mechanical guard mode TPS, pedal position and mechanical guard Inhibits idle speed control sensor(s) failure(s) Inhibits cruise control Inhibits traction control / stability control Inhibits power limiting P1241 Sensor power supply low voltage Ignition ON > 5 seconds Y 2 1 Refer to P1240 Default Action ECM to throttle sensors reference voltage circuit (TPS, pedal position and [R, M] short circuit to ground mechanical guard sensors) TPS, pedal position and mechanical guard (ECM pins EM10-21, EM11-8) sensor(s) failure(s) Engine Management: V8 AJ

24 P1242 Sensor power supply high Ignition ON > 5 seconds Y 2 1 Refer to P1240 Default Action ECM to throttle sensors reference voltage circuit voltage (TPS, pedal position and [R, M] open circuit, high resistance, short circuit to mechanical guard sensors) high voltage (ECM pins EM10-21, EM11-8) TPS, pedal position and mechanical guard sensor(s) failure(s) P1243 Sensor reference ground Ignition ON > 5 seconds Y 2 1 Refer to P1240 Default Action ECM to sensors reference ground circuit malfunction (throttle sensors, [R, M] open circuit, high resistance ECTS, IATS) Throttle sensor(s), ECTS, IATS failure(s) (ECM pins EM10-20, EM11-12) P1245 Engine crank signal low voltage Start engine; idle Y 2 N None Starter relay coil to ECM / BPM circuit open circuit P1246 Engine crank signal high voltage Start engine; drive / accelerate > 13 mph Y 2 N None Starter relay coil to ECM / BPM circuit short circuit (20 km/h) rpm decelerate to to B+ voltage stop; repeat (5 times total) BPM failure P1250 Engine load malfunction Engine at normal operating temperature; N N N None Air intake leak drive vehicle; accelerate from 3500 to Engine breather leak 6000 rpm within 6 seconds; TPS circuit fault (DTC P0121) drive mph (70 95 km/h); Throttle valve spring failure rpm; > 10 seconds P1251 Throttle position malfunction Drive vehicle; N N N None TPS to ECM wiring open circuit or high resistance (engine off) decelerate to stop, ignition OFF > 5 TPS to ECM sensing circuits ( 1 or 2 ) seconds (foot off accelerator); ignition ON short circuit to high voltage TPS failure Throttle motor disconnected Throttle motor to ECM drive circuits short circuit or open circuit Throttle motor failure Throttle assembly failure Engine Management: V8 AJ

25 P1252 Mechanical guard position Drive vehicle; N N 1 When fault is detected, ECM: VSV 1,2,3 vacuum and/or electrical circuit fault(s) malfunction (cruise control) engage cruise control > 5 seconds [A, M] Inhibits cruise control open circuit, short circuit or high resistance Mechanical guard sensor to ECM sense circuit Mechanical guard sensor failure Mechanical guard actuator seized / spring broken Throttle vacuum actuator fault P1253 Mechanical guard position Engine at normal operating temperature; N N 1 When fault is detected, ECM: VSV 1,2,3 vacuum and/or electrical circuit fault(s) malfunction (engine off) drive / accelerate from 3500 to 6000 rpm [A, M] Inhibits cruise control Mechanical guard sensor to ECM sense circuit within 6 seconds; decelerate to stop, open circuit, short circuit or high resistance ignition OFF > 5 seconds (foot off Mechanical guard sensor failure accelerator); ignition ON Mechanical guard actuator seized / spring broken Throttle vacuum actuator fault P1260 Security input (not used NAS) Ignition ON > 10 seconds N N N None KTM to ECM circuit short circuit, high resistance or open circuit KTM failure P1313 Misfire rate catalyst damage Engine at idle, or steady between Y 1 1 When CK ENG MIL is activated Cylinder compression low A bank (1) rpm; > 2 minutes 30 seconds [A, M] (DTC flagged; second trip), ECM: Worn camshaft / broken valve spring(s) Limits engine speed to 3000 rpm Fuel delivery pressure (low / high) Inhibits A bank closed loop Fuel injector(s) blocked / leaking Note: This DTC will flag only Fuel injector(s) continuously open when accompanied by a random Inhibits A bank adaptive Fuel contamination or individual cylinder misfire DTC: Fuel injector circuit fault(s) P0300; P0301 P0304 Inhibits canister purge (Injector DTCs also flagged) Inhibits EGR Spark plug failure / fouled / incorrect gap ECM to ignition module primary circuit fault(s) (Cylinder misfire detected DTC also flagged) Ignition module to ignition coil primary circuit fault(s) (Cylinder misfire detected DTC also flagged) Ignition module ground circuit open circuit, high resistance Ignition coil failure Ignition module failure Engine Management: V8 AJ

26 P1314 Misfire rate catalyst damage Engine at idle, or steady between Y 1 1 When CK ENG MIL is activated Refer to P1313 Possible Causes B bank (2) rpm; > 2 minutes 30 seconds [A, M] (DTC flagged; second trip), ECM: Limits engine speed to 3000 rpm Inhibits B bank closed loop Note: This DTC will flag only when accompanied by an Inhibits B bank adaptive individual cylinder misfire DTC: P0300 P0308. Inhibits canister purge Inhibits EGR P1316 Misfire excess emission Engine at idle, or steady between Y 1 1 When CK ENG MIL is activated Refer to P1313 Possible Causes rpm; > 2 minutes 30 seconds [A, M] (DTC flagged; second trip), ECM: Limits engine speed to 3000 rpm Note: This DTC will flag only Inhibits closed loop when accompanied by an individual cylinder misfire DTC: Inhibits adaptive P0300 P0308. Inhibits canister purge Inhibits EGR P1336 CKPS / CMPS sensors Run engine > 5 seconds Y 2 N None CKPS / CMPS disconnected synchronization malfunction CKPS / CMPS gap incorrect / foreign matter on sensor face CKPS / CMPS sensing circuit open circuit, short circuit to ground, short circuit to high voltage CKPS / CMPS failure P1367 Ignition monitor Run engine > 5 seconds < 3000 rpm Y 2 1 When fault is detected, ECM: Ignition module 1 disconnected (ignition module 1) [A, M] Limits engine speed to 3000 rpm Ignition module 1 to ECM circuits open circuit, short circuit to ground or short circuit to B+ voltage Ignition module 1 ground circuit fault Ignition coil relay failure Ignition coil open / short circuit Ignition module 1 failure Engine Management: V8 AJ

27 P1368 Ignition monitor Run engine > 5 seconds < 3000 rpm Y 2 1 When fault is detected, ECM: Ignition module 2 disconnected (ignition module 2) [A, M] Limits engine speed to 3000 rpm Ignition module 2 to ECM circuits open circuit, short circuit to ground or short circuit to B+ voltage Ignition module 2 ground circuit fault Ignition coil relay failure Ignition coil open / short circuit Ignition module 2 failure P1392 VVT solenoid circuit open circuit Ignition ON > 5 seconds Y 2 N When CK ENG MIL is activated ECM to VVT solenoid valve circuit open circuit, A bank (DTC flagged; second trip), ECM: high resistance, short circuit to high voltage Inhibits VVT VVT solenoid valve failure P1393 VVT solenoid circuit short circuit Ignition ON > 5 seconds Y 2 N When CK ENG MIL is activated ECM to VVT solenoid valve short circuit to ground A bank (DTC flagged; second trip), ECM: VVT solenoid valve failure Inhibits VVT P1396 VVT solenoid malfunction Engine at normal operating temperature; Y 2 N When CK ENG MIL is activated ECM to VVT solenoid valve circuit fault B bank drive > 13 mph (20 km/h) > 1700 rpm (DTC flagged; second trip), ECM: (refer to P1392, P1393) > 5 seconds Inhibits VVT VVT solenoid valve actuator sticking Oil supply fault VVT unit fault Camshaft drive fault CKPS / CMPS circuits fault(s) (refer to P0335, P0340) P1397 VVT solenoid circuit open circuit Ignition ON > 5 seconds Y 2 N When CK ENG MIL is activated ECM to VVT solenoid valve open circuit, B bank (DTC flagged; second trip), ECM: high resistance, short circuit to high voltage Inhibits VVT VVT solenoid valve failure P1398 VVT solenoid circuit short circuit Ignition ON > 5 seconds Y 2 N When CK ENG MIL is activated ECM to VVT solenoid valve short circuit to ground B bank (DTC flagged; second trip), ECM: VVT solenoid valve failure Inhibits VVT Engine Management: V8 AJ

28 P1475 Radiator fans slow (series) circuit Engine at normal operating temperature; N N N None Radiator fan control relay module to ECM series malfunction fans cycle ON / OFF drive circuit (relay pin 9) fault Relay coil ignition power supply open circuit ECM ground circuit fault (relay coil drive) ECTS circuit malfunction (refer to P0116) P1476 Radiator fans fast (parallel) circuit Engine at normal operating temperature; N N N None Radiator fan control relay module to ECM malfunction fans cycle ON / OFF parallel drive circuit (relay pin 7) fault Relay coil ignition power supply open circuit ECM ground circuit fault (relay coil drive) ECTS circuit malfunction (refer to P0116) P1516 Gear change PARK / NEUTRAL Engine at normal operating temperature; Y 2 N None Transmission rotary switch to ECM circuit driving malfunction drive mph ( km/h) open circuit or high resistance rpm > 30 seconds Rotary switch failure D 4 switch to TCM circuit open circuit or high resistance D 4 switch fault P1517 Engine cranking PARK / NEUTRAL Start engine N N* N When fault is detected, ECM: Transmission rotary switch to ECM circuit malfunction Inhibits fuel injection open circuit or high resistance Rotary switch failure * If engine will not start, CHECK ENGINE MIL will remain on. Engine Management: V8 AJ

29 P1571 Brake switch malfunction Drive vehicle; engage cruise control N N 1 When fault is detected, ECM: Brake switch to ECM circuit open circuit, > 10 seconds disengage cruise control; [A, M] Inhibits cruise control short circuit to ground, high resistance repeat (5 total cycles) Brake switch ignition switched ground circuit open circuit Brake switch failure Brake cancel switch to ECM circuit open circuit, short circuit to ground, high resistance Brake cancel switch to cruise control switch to ECM circuit open circuit, short circuit to ground, high resistance Brake cancel switch ignition switched power supply open circuit Brake cancel switch failure Cruise control switch failure P1606 EMS control relay malfunction Ignition ON; ignition OFF; ignition ON N N None None ECM control relay failure > 5 seconds ECM control relay to ECM circuit fault ECM control relay coil power supply open circuit ECM ground circuit fault (relay coil drive) P1609 ECM microprocessor-to- Ignition ON > 5 seconds Y 2 N None ECM FCCP (programming) circuit microprocessor communication (ECM pin EM11-3) short circuit to ground failure ECM failure P1611 Throttle angle malfunction Ignition ON > 5 seconds Y 2 1 When RED MIL is activated TPS circuit fault (refer to P0121) [R, M] (first trip), ECM: Pedal position sensor circuit fault (refer to P01121) Defaults throttle to Throttle assembly failure mechanical guard mode ECM failure Inhibits idle speed control Inhibits cruise control Inhibits traction / stability control Inhibits power limiting Engine Management: V8 AJ