TEST REPORT EN Information technology equipment Safety Part 1: General requirements

Transcription

1

2 Report Reference No. Compiled by (+ signature) Approved by (+ signature) age 2 of 78 TEST REORT Information technology equipment Safety art 1: General requirements See cover sheet See cover sheet Date of issue November 16, 2011 Testing laboratory Name Address Testing location Address Client Name Bureau Veritas Consumer roducts Services (H.K.) Ltd., Taoyuan Branch No. 47, 14th Ling, Chia au Vil., Lin Kou Dist.,New Taipei City, Taiwan ( R.O.C ) Bureau Veritas Consumer roducts Services (H.K.) Ltd., Taoyuan Branch No. 19, Hwa Ya 2nd Rd, Kueishan Taoyuan, Taiwan, R.O.C. Shin Chuan Computer Co., Ltd. Address 6F.-2, No.68, Liancheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) Test specification Standard : A11: A1:2010 Test procedure Non-standard test method Test Report Form/blank test report Test Report Form No. TRF originator. CE Marking serial in LVD. IECEN60950_1C SGS Fimko Ltd Master TRF Dated Test item Description Trademark ortable Data Terminal Model and/or type reference Manufacturer Rating(s) SC900, M1000 Shin Chuan Computer Co., Ltd. Optional; 5Vdc, 1A for adapter or 1.5A for Docking

3 age 3 of 78 Copy of marking plate and summary of test results (information/comments): For model SC900: For model M1000: Laser marking: For Laser scan engine (Optoelectronics Co., Ltd., model: MDL-1000) For Battery ack: This is a reference label. Final label shall be including the content of it.

4 age 4 of 78 Test item particulars Equipment mobility [] movable [X] hand-held [] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains Operating condition Access location [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [X] not directly connected to the mains [X] continuous [] rated operating / resting time: [X] operator accessible [] restricted access location Over voltage category (OVC) [] OVC I [] OVC II [] OVC III [] OVC IV [X] other: DC Supply. Mains supply tolerance (%) or absolute mains supply values Tested for IT power systems [] Yes [X] No IT testing, phase-phase voltage (V) Class of equipment [] Class I [] Class II [X] Class III [] Not classified Considered current rating (A) See page 2 Ratings ollution degree (D) [] D 1 [X] D 2 [] D 3 I protection class Altitude during operation (m) Altitude of test laboratory (m) Mass of equipment (kg) ossible test case verdicts: IX0 < 2000m 250m 0.24 kg - test case does not apply to the test object - test object does meet the requirement (ass) - test object does not meet the requirement F (Fail) Testing Date of receipt of test item July 07, 2011 Date(s) of performance of tests July 07, 2011 to August 01, 2011 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator.

5 age 5 of 78 General product information: 1) The equipment is a hand held of ortable Data Terminal. 2) Dimension of EUT: 144 by 62 by 35.8 mm. 3) The ortable Data Terminal has Bar Code scanning function, provided with Class 2 laser scan engine and battery pack which charged by power adapter or docking. 4) The maximum ambient temperature is specified as 50 5) The maximum ambient temperature at adapter report is specified as 40, however after additional test the maximum ambient temperature can reach to 50. 6) The model B battery pack top and bottom enclosure are secured together by ultrasonic welded. 7) The power from external docking is not evaluated in this report. However, for acceptance of the accessory docking output shall comply with LS requirements according to IEC/EN clause 2.5, docking with output rating (5Vdc, 1.5A), maximum temperature 50 C. 8) All testing were conducted on Model SC900 to represent other series. 9) The model M1000 sound pressure test (Sub-clause 1.3.z1) complied with the requirements of EN (tested in this report). For EN standard., the tests data as below: Channel Measured voltage (mv) Limits Channel L mV Channel R mV Model Difference Trademark roduct name Model mane ower with Input current Communication orts Remark ortable Data Terminal SC900 Adapter or Docking With adapter 1 A With docking 1.5 A USB port M1000 Docking 1.5A Headset port For marketing purpose Test condition: Temperature: 25 o C Relative humidity: 60% Air pressure: 950 mbar The test sample was a pre-production sample without serial number.

6 age 6 of 78 1 GENERAL 1.5 Components General Components, which were found to affect safety aspects, are conformed to the relevant IEC component standards and/or comply with the requirements of this standard. Comply with IEC or relevant component standard (see appended table 1.5.1) Evaluation and testing of components Components which are certified to IEC and/or national standards are used correctly within their ratings. Components not covered by IEC standards are tested under the conditions presented in the equipment Thermal controls No thermal controls used Transformers Class III equipment, supplied by the SELV provided by the certified power adapter Interconnecting cables Interconnecting cable for Interconnection is carrying only SELV voltages with power consumption below 240 VA Capacitors bridging insulation Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems Surge suppressors General No such varistor used rotection of VDRs No such varistor used Bridging of functional insulation by a VDR No such varistor used Bridging of basic insulation by a VDR No such varistor used Bridging of supplementary, double or reinforced insulation by a VDR No such varistor used.

7 age 7 of ower interface AC power distribution systems Class III equipment, supplied by the SELV provided by the certified power adapter Input current (See appended table 1.6.2) Voltage limit of hand-held equipment The rated voltage of ortable Data Terminal not exceed 250V Neutral conductor Class III equipment, supplied by the SELV provided by the certified power adapter. 1.7 Marking and instructions ower rating See below. Rated voltage(s) or voltage range(s) (V)...: DC 5V Symbol for nature of supply, for d.c. only...: Symbol IEC-5031 used. Rated frequency or rated frequency range (Hz)...: The EUT is supplied by DC Rated current (ma or A)...: 1A for adapter, 1.5A for docking Manufacturer s name or trade-mark or Manufacturer s name: Shin identification mark...: Chuan Computer Co., Ltd. or Trade-mark: Model identification or type reference...: SC900, M1000 Symbol for Class II equipment only...: Class III equipment, supplied by the SELV provided by the certified power adapter. Other markings and symbols... : Additional symbols or markings do not give risk to misunderstanding Safety instructions and marking Safety related information in English has been evaluated. The manufacturer commits to provide them in the language of the countries where the product will be distributed General See below Disconnect devices Class III equipment, supplied by the SELV provided by the certified power adapter Overcurrent protective device No such device.

8 age 8 of IT power distribution systems Class III equipment, supplied by the SELV provided by the certified power adapter Operator access with a tool No tool is necessary when operating this product Ozone This EUT is not intended to produce the ozone Short duty cycles This EUT is a continuous operation equipment Supply voltage adjustment...: No such device Methods and means of adjustment; reference to installation instructions...: No such device ower outlets on the equipment...: No power outlets Fuse identification (marking, special fusing characteristics, cross-reference)...: Class III equipment, supplied by the SELV provided by the certified power adapter Wiring terminals See below rotective earthing and bonding terminals...: Class III equipment, no protective earthing Terminals for a.c. mains supply conductors Class III equipment. Not connected to the a.c. mains directly Terminals for d.c. mains supply conductors The EUT is not intended to be connected to the d.c. mains Controls and indicators No safety relevant switch or control Identification, location and marking...: See below Colours...: No safety relevant control or indicator Symbols according to IEC : No safety relevant control or indicator Markings using figures... : No safety relevant switch Isolation of multiple power sources... : Not used Thermostats and other regulating devices... : No thermostat or other regulating devices Durability After this test there was no damage to the label. The marking on the label did not fade. There was no curling or lifting on the label edge Removable parts No removable parts Replaceable batteries... : rovided in the user manual.

9 age 9 of 78 Language(s)... : Only verified the English version Equipment for restricted access locations... : This product is not intended to be used in the restricted access locations. 2 ROTECTION FROM HAZARDS 2.1 rotection from electric shock and energy hazards rotection in operator access areas See below Access to energized parts Class III equipment, there are no hazardous voltages generated inside the EUT. Test by inspection...: The inspection was conducted as below. Test with test finger (Figure 2A)...: There is no hazardous voltage generated inside the EUT. Test with test pin (Figure 2B)...: There is no hazardous voltage generated inside the EUT. Test with test probe (Figure 2C)...: No TNV circuit in the EUT Battery compartments No TNV circuit in the equipment Access to ELV wiring No ELV wiring in operator accessible area. Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) Access to hazardous voltage circuit wiring No hazardous voltage wiring in operator accessible area Energy hazards...: Class III equipment, supplied by the SELV provided by certified power adapter. And there is no hazardous energy generating in the EUT Manual controls No such device Discharge of capacitors in equipment Class III equipment. This clause has been considered during the certified power adapter approvals. Measured voltage (V); time-constant (s)...: Energy hazards d.c. mains supply This product is not intended to be connected to the d.c. mains supply. a) Capacitor connected to the d.c. mains supply..:

10 age 10 of 78 b) Internal battery connected to the d.c. mains supply...: Audio amplifiers...: There is no audio output connector in this product rotection in service access areas No maintenance works necessary in operation mode rotection in restricted access locations It is not intended to be used in restricted locations. 2.2 SELV circuits General requirements Class III equipment, supplied by SELV Voltages under normal conditions (V)...: Class III equipment, supplied by SELV Voltages under fault conditions (V)...: Class III equipment, no hazardous voltage generated inside the EUT Connection of SELV circuits to other circuits... : SELV circuit only connected to the SELV circuit. 2.3 TNV circuits Limits No TNV circuits inside the EUT. Type of TNV circuits...: Separation from other circuits and from accessible parts General requirements rotection by basic insulation rotection by earthing rotection by other constructions...: Separation from hazardous voltages Insulation employed...: Connection of TNV circuits to other circuits Insulation employed...: Test for operating voltages generated externally 2.4 Limited current circuits General requirements No limited current circuit inside it Limit values

11 age 11 of 78 Frequency (Hz)...: Measured current (ma)...: Measured voltage (V)...: Measured circuit capacitance (nf or µf)...: Connection of limited current circuits to other circuits 2.5 Limited power sources a) Inherently limited output b) Impedance limited output The output of the battery pack & backup battery pack was in compliance with the value in Table 2B for both normal and abnormal condition. c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), For battery pack & backup max. apparent power (VA)...: battery pack, see appended table 2.5. Current rating of overcurrent protective device (A).: 2.6 rovisions for earthing and bonding rotective earthing Class III equipment, no protective earthing inside the EUT Functional earthing rotective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG...: Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG...: rotective current rating (A), cross-sectional area (mm 2 ), AWG...:

12 age 12 of Resistance of earthing conductors and their terminations; resistance (Ω), voltage drop (V), test current (A), duration (min)...: Colour of insulation...: Terminals General rotective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)...: Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth arts that can be removed by an operator arts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Class III equipment. Not connected to the a.c. mains directly. Instructions when protection relies on building installation Faults not simulated in Short-circuit backup protection Number and location of protective devices...: rotection by several devices Warning to service personnel...: No service work was necessary. 2.8 Safety interlocks General principles There is no safety interlock in the EUT.

13 age 13 of rotection requirements Inadvertent reactivation Fail-safe operation Moving parts Overriding Switches and relays Contact gaps (mm)... : Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation roperties of insulating materials Natural rubber, asbestos or hygroscopic materials are not used Humidity conditioning Class III equipment, no critical insulation in the EUT. Relative humidity (%), temperature ( C)......: Grade of insulation Only the functional Insulation inside the EUT Separation from hazardous voltages Class III equipment, supplied by the SELV provided by certified power adapter. Method(s) used...: 2.10 Clearances, creepage distances and distances through insulation General Class III equipment, no critical insulation in the EUT Frequency...: Class III equipment ollution degrees...: This report considered the pollution degree II Reduced values for functional insualtion Considered c) Intervening unconnected conductive parts Class III equipment, no critical insulation in the EUT Insulation with varying dimensions Class III equipment, no critical insulation in the EUT Special separation requirements Class III equipment, no critical insulation in the EUT.

14 age 14 of Insulation in circuits generating starting pulses No such circuit in the equipment Determination of working voltage Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT General Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT RMS working voltage eak working voltage Clearances General Mains transient voltages Class III equipment. Not connected to the a.c. mains directly. a) AC mains supply...: Class III equipment. Not connected to the a.c. mains directly. b) Earthed d.c. mains supplies...: The equipment is not intended to be supplied by the d.c. mains. c) Unearthed d.c. mains supplies...: The equipment is not intended to be supplied by the d.c. mains. d) Battery operation...: The equipment is not intended to be supplied by the battery Clearances in primary circuits Class III equipment, no critical insulation in the EUT Clearances in secondary circuits Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Clearances in circuits having starting pulses No such circuit Transients from a.c. mains supply...: Class III equipment. Not connected to the a.c. mains directly Transients from d.c. mains supply...: The EUT is not intended to be connected to the d.c. mains Transients from telecommunication networks and The EUT is not connected to cable distribution systems...: the telecommunication network and cable distribution system.

15 age 15 of Measurement of transient voltage levels Class III equipment. Not connected to the mains directly. a) Transients from a mains suplply Class III equipment. Not connected to the mains directly. For an a.c. mains supply...: Class III equipment. Not connected to the a.c. mains directly. For a d.c. mains supply...: Class III equipment. Not connected to the d.c. mains directly. b) Transients from a telecommunication network : Class III equipment. Not connected to the mains directly Creepage distances Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT General Material group and caomparative tracking index CTI tests...: Minimum creepage distances Solid insulation General Distances through insulation Insulating compound as solid insulation Semiconductor devices Cemented joints Thin sheet material General Separable thin sheet material Number of layers (pcs)...: Non-separable thin sheet material Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Thin sheet material standard test procedure Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT. Electric strength test

16 age 16 of Thin sheet material alternative test procedure Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT. Electric strength test Insulation in wound components Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Wire in wound components Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT. Working voltage...: a) Basic insulation not under stress...: b) Basic, supplemetary, reinforced insulation...: c) Compliance with Annex U...: Two wires in contact inside wound component; angle between 45 and 90...: Wire with solvent-based enamel in wound components Electric strength test Routine test Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Additional insulation in wound components Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT. Working voltage...: - Basic insulation not under stress...: - Supplemetary, reinforced insulation...: Construction of printed boards See below Uncoated printed boards Only the functional Insulation inside the EUT. See sub-clause Coated printed boards No coated printed boards Insulation between conductors on the same inner surface of a printed board Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT.

17 age 17 of Insulation between conductors on different layers of a printed board Distance through insulation Number of insulation layers (pcs)...: Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Component external terminations Tests on coated printed boards and coated components No such construction Sample preparation and preliminary inspection No such construction Thermal conditioning No such construction Electric strength test No such construction Abrasion resistance test No such construction Thermal cycling No such construction Test for ollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints No such construction. ollution degree 2 is considered. Class III equipment, no critical insulation in the EUT. Only the functional Insulation inside the EUT Enclosed and sealed parts No hermetically sealed component. 3 WIRING, CONNECTIONS AND SULY 3.1 General Current rating and overcurrent protection Internal wiring gauge is suitable for current intended to be carried rotection against mechanical damage Wire ways are smooth and free from edges. Wires are adequately fixed to prevent excessive strain on wire and terminals and avoiding damage to the insulation of the conductors Securing of internal wiring Internal wiring is secured against excessive strain, loosening of terminals and damage to the conductor insulation.

18 age 18 of Insulation of conductors The insulation of the individual conductors is suitable for the application and the working voltage Beads and ceramic insulators Not used Screws for electrical contact pressure No screws of insulating material for electrical connections, or where supplementary or reinforced insulation could be impaired by a metal replacement Insulating materials in electrical connections No non-metallic materials in electrical connections Self-tapping and spaced thread screws No self tapping screws are used Termination of conductors All conductors are reliable secured. 10 N pull test 10 N pull tests performed for all relevant conductors. No hazards caused hereby Sleeving on wiring No such sleeves or tubing used. 3.2 Connection to a mains supply Means of connection See below Connection to an a.c. mains supply Class III equipment. Not directly connected to the a.c. mains Connection to a d.c. mains supply Class III equipment. Not directly connected to d.c. mains Multiple supply connections Class III equipment. Not directly connected to the mains ermanently connected equipment Not a permanently connected equipment. Number of conductors, diameter of cable and conduits (mm)...: Appliance inlets ower supply cords AC power supply cords Type...:

19 age 19 of 78 Rated current (A), cross-sectional area (mm 2 ), AWG...: DC power supply cords Class III equipment. Not directly connected to d.c. mains Cord anchorages and strain relief Mass of equipment (kg), pull (N)...: Longitudinal displacement (mm)...: rotection against mechanical damage Cord guards Diameter or minor dimension D (mm); test mass (g)...: Radius of curvature of cord (mm)...: Supply wiring space 3.3 Wiring terminals for connection of external conductors Wiring terminals Class III equipment. Not directly connected to the mains Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, crosssectional area (mm 2 )...: Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm)...: Wiring terminal design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the mains supply General requirement Class III equipment. Not directly connected to the mains Disconnect devices ermanently connected equipment The EUT is not permanently connected equipment arts which remain energized

20 age 20 of Switches in flexible cords Number of poles - single-phase and d.c. equipment Number of poles - three-phase equipment Switches as disconnect devices lugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements See below Types of interconnection circuits...: SELV circuit only connected to SELV circuit ELV circuits as interconnection circuits No ELV interconnection circuits Data ports for additional equipment The data ports were not intended to supply the power to other accessory. 4 HYSICAL REQUIREMENTS 4.1 Stability Angle of 10 Mass less than 7kg. Test force (N)...: Not floor standing equipment. 4.2 Mechanical strength General See below Steady force test, 10 N After test, no safety relevant damages Steady force test, 30 N No door or cover in the operator access area Steady force test, 250 N 250N applied to enclosure of battery pack & backup battery pack, no energy or other hazards Impact test There is no hazardous voltage and energy inside it. The test is not considered necessary. Fall test There is no hazardous voltage and energy inside it. The test is not considered necessary.

21 age 21 of 78 Swing test There is no hazardous voltage and energy inside it. The test is not considered necessary Drop test; height (mm)...: No safety relevant damages Stress relief test The test was conducted at 83.4 C environments for 7hrs. After the test, no safety relevant damage Cathode ray tubes No CRT inside the EUT. icture tube separately certified...: No CRT inside the EUT High pressure lamps No high pressure lamps Wall or ceiling mounted equipment; force (N)...: No wall mount or ceiling mounted function for the EUT. 4.3 Design and construction Edges and corners Edges and corners of the enclosure are rounded Handles and manual controls; force (N)... : No such device Adjustable controls No such device Securing of parts Electrical and mechanical connections and parts expected to withstand usual mechanical stress Connection by plugs and sockets No mismatch of connectors, plugs or sockets possible Direct plug-in equipment Class III equipment. Torque...: Compliance with the relevant mains plug standard...: Class III equipment Heating elements in earthed equipment No heating element Batteries After testing, no chemical leak, explosion, and emission of flame of the EUT, see appended table. - Overcharging of a rechargeable battery See appended table. - Unintentional charging of a non-rechargeable battery Rechargeable battery used. - Reverse charging of a rechargeable battery Not possible to reverse in battery compartment. - Excessive discharging rate for any battery (See appended table and 5.3)

22 age 22 of Oil and grease No oil and grease inside the equipment Dust, powders, liquids and gases The equipment is not intended to be exposed to dust, powers, liquids and gases Containers for liquids or gases No container for liquids or gases provided Flammable liquids...: No flammable liquids in the equipment. Quantity of liquid (l)...: No flammable liquids in the equipment. Flash point ( C)...: No flammable liquids in the equipment Radiation See below General The energy of the Laser scan engine is Laser class 1 or Laser class 2 and see for detail Ionizing radiation No ionizing radiation. Measured radiation (pa/kg)...: No ionizing radiation. Measured high-voltage (kv)...: No ionizing radiation. Measured focus voltage (kv)...: No ionizing radiation. CRT markings...: No ionizing radiation Effect of ultraviolet (UV) radiation on materials No UV radiation. art, property, retention after test, flammability classification...: No UV radiation Human exposure to ultraviolet (UV) radiation...: No UV radiation Laser (including LEDs) Considered in Laser scan engine which is UL Demko certified according to IEC :2007. Laser warning labels are marked on the EUT external enclosure. Laser class...: Laser class 2 (for Laser scan engine: Optoelectronics Co., Ltd., model: MDL-1000) Other types...: No other type radiation. 4.4 rotection against hazardous moving parts General No hazardous moving part in operator access areas.

23 age 23 of rotection in operator access areas...: No hazardous moving part in operator access areas rotection in restricted access locations...: No hazardous moving part in restricted access areas rotection in service access areas No hazardous moving in the service access area 4.5 Thermal requirements General See below Temperature tests (See appended table 4.5.1) Normal load condition per Annex L...: (See appended table 1.6.2) Temperature limits for materials (See appended table 4.5.1) Touch temperature limits (See appended table 4.5.1) Resistance to abnormal heat...: No such construction inside EUT. This clause has been considered during the certified power adapter approvals. 4.6 Openings in enclosures Top and side openings See Clause Dimensions (mm)...: Bottoms of fire enclosures See Clause Construction of the bottomm, dimensions (mm)..: Doors or covers in fire enclosures No such parts Openings in transportable equipment No openings provided Constructional design measures No openings provided. Dimensions (mm)...: Evaluation measures for larger openings No such openings Use of metallized parts No metalized parts Adhesives for constructional purposes No adhesives for construction purposes. Conditioning temperature ( C), time (weeks)...: 4.7 Resistance to fire Reducing the risk of ignition and spread of flame See below. Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests (See appended table 5.3)

24 age 24 of Conditions for a fire enclosure With having the following components: -components with windings -semiconductor devices, transistors, diodes, integrated circuits. -resistors, capacitors, inductors arts requiring a fire enclosure arts not requiring a fire enclosure (See appended table 5.3) Materials General (See appended table 5.3) Materials for fire enclosures HB or better Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures No such parts Materials for air filter assemblies No air filter provided Materials used in high-voltage components No high-voltage component inside the equipment. 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General Class III equipment, supplied by SELV Configuration of equipment under test (EUT) Class III equipment, supplied by SELV Single connection to an a.c. mains supply Class III equipment. Not connected to the a.c. mains directly Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply No such construction. No such construction Test circuit Class III equipment, supplied by SELV Application of measuring instrument Class III equipment, supplied by SELV Test procedure Class III equipment, supplied by SELV.

25 age 25 of Test measurements Class III equipment, supplied by SELV. Supply voltage (V)...: Measured touch current (ma)...: Max. allowed touch current (ma)...: Measured protective conductor current (ma)...: Max. allowed protective conductor current (ma)...: Equipment with touch current exceeding 3,5 ma Class III equipment, supplied by SELV and no direct connection to the mains General...: Class III equipment, supplied by SELV and no direct connection to the mains Simultaneous multiple connections to the supply Class III equipment, supplied by SELV and no direct connection to the mains Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system Supply voltage (V)...: Measured touch current (ma)...: Max. allowed touch current (ma)...: Summation of touch currents from telecommunication networks EUT is not connected to a telecommunication system and a cable distribution system. EUT is not connected to a telecommunication system and a cable distribution system. Not connected to the telecommunication networks. a) EUT with earthed telecommunication ports...: b) EUT whose telecommunication ports have no reference to protective earth 5.2 Electric strength General Class III equipment, supplied by SELV and not directly connected to the mains Test procedure Class III equipment, supplied by SELV and not directly connected to the mains.

26 age 26 of Abnormal operating and fault conditions rotection against overload and abnormal operation (See appended table 5.3) Motors (see appended table 5.3) Transformers No transformers Functional insulation...: Method c) used. Result see appended table Electromechanical components No electromechanical component Audio amplifiers in ITE...: There is no audio output connector in this product Simulation of faults See appended table Unattended equipment The equipment was not for unattended use Compliance criteria for abnormal operating and fault conditions See below During the tests No fire propagated beyond the equipment. No molten metal was emitted After the tests No consequent testing necessary. 6 CONNECTION TO TELECOMMUNICATION NETWORKS 6.1 rotection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment rotection from hazardous voltages Separation of the telecommunication network from earth Requirements No connection to the telecommunication network. Supply voltage (V)...: Current in the test circuit (ma)...: Exclusions...: 6.2 rotection of equipment users from overvoltages on telecommunication networks Separation requirements No connection to the telecommunication network Electric strength test procedure Impulse test Steady-state test Compliance criteria

27 age 27 of rotection of the telecommunication wiring system from overheating Max. output current (A)...: The EUT is not intended to supply other units via telecommunication line. Current limiting method...: 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS 7.1 General No connection to the cable distribution system. 7.2 rotection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 rotection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test

28 age 28 of 78 A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) The mass of the EUT is less than 18 kg. A.1.1 Samples...: Wall thickness (mm)...: A.1.2 Conditioning of samples; temperature ( C)...: A.1.3 Mounting of samples...: A.1.4 Test flame (see IEC ) Flame A, B, C or D...: A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material...: Wall thickness (mm)...: A.2.2 Conditioning of samples; temperature ( C)......: A.2.3 Mounting of samples...: A.2.4 Test flame (see IEC ) Flame A, B or C...: A.2.5 Test procedure A.2.6 Compliance criteria A.2.7 Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples A.3.2 Test procedure

29 age 29 of 78 A.3.3 Compliance criterion B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.2) B.1 General requirements The vibrator was in compliance with the requirement. osition...: See appended table Manufacturer...: See appended table Type...: See appended table Rated values...: See appended table B.2 Test conditions The tests were carried out under simulated conditions on the bench. B.3 Maximum temperatures See appended table 5.3. B.4 Running overload test Not carried out due to the design of electronic drive circuit. B.5 Locked-rotor overload test The motor is the secondary motor. Test duration (days)...: Electric strength test: test voltage (V)...: B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)...: B.7 Locked-rotor overload test for d.c. motors in secondary circuits See below. B.7.1 General See below. B.7.2 Test procedure See below, the alternative test procedure used. B.7.3 Alternative test procedure See appended table 5.3. No ignition of the wrapping tissue and cheesecloth. B.7.4 Electric strength test; test voltage (V)... : B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors

30 age 30 of 78 Operating voltage (V)...: C ANNEX C, TRANSFORMERS (see and 5.3.3) osition...: Class III equipment, supplied by the SELV provided by the certified power adapter. Manufacturer...: Type...: Rated values...: Method of protection...: C.1 Overload test C.2 Insulation rotection from displacement of windings...: D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) D.1 Measuring instrument Class III equipment, supplied by SELV and no direct connection to the mains. D.2 Alternative measuring instrument E ANNEX E, TEMERATURE RISE OF A WINDING (see ) F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEAGE DISTANCES (see 2.10 and Annex G) G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES G.1 Clearances Not used. G.1.1 General G.1.2 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V) G.2.1 AC mains supply...: G.2.2 Earthed d.c. mains supplies...: G.2.3 Unearthed d.c. mains supplies...: G.2.4 Battery operation...:

31 age 31 of 78 G.3 Determination of telecommunication network transient voltage (V)...: G.4 Determination of required withstand voltage (V) G.4.1 Mains transients and internal repetitive peaks...: G.4.2 Transients from telecommunication networks...: G.4.3 Combination of transients G.4.4 Transients from cable distribution systems G.5 Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network G.6 Determination of minimum clearances...: H ANNEX H, IONIZING RADIATION (see ) J ANNEX J, TABLE OF ELECTROCHEMICAL OTENTIALS (see ) Metal(s) used...: K ANNEX K, THERMAL CONTROLS (see and 5.3.8) K.1 Making and breaking capacity No thermal control inside the EUT. K.2 Thermostat reliability; operating voltage (V)...: K.3 Thermostat endurance test; operating voltage (V)...: K.4 Temperature limiter endurance; operating voltage (V)...: K.5 Thermal cut-out reliability K.6 Stability of operation L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYES OF ELECTRICAL BUSINESS EQUIMENT (see and 4.5.2) L.1 Typewriters No such device in the EUT. L.2 Adding machines and cash registers L.3 Erasers L.4 encil sharpeners L.5 Duplicators and copy machines

32 age 32 of 78 L.6 Motor-operated files L.7 Other business equipment M ANNEX M, CRITERIA FOR TELEHONE RINGING SIGNALS (see 2.3.1) M.1 Introduction No phone ringing was generated in the EUT. M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)...: M Voltage (V)...: M Cadence; time (s), voltage (V)...: M Single fault current (ma)...: M.3.2 Tripping device and monitoring voltage...: M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)...: N ANNEX N, IMULSE TEST GENERATORS (see , , , , 7.3.2, and Clause G.5) N.1 ITU-T impulse test generators Not used. N.2 IEC impulse test generator ANNEX, NORMATIVE REFERENCES Q ANNEX Q, Voltage dependent resistors (VDRs) (see ) a) referred climatic categories...: No such component. b) Maximum continuous voltage...: c) ulse current...: R ANNEX R, EXAMLES OF REQUIREMENTS FOR QUALITY CONTROL ROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) Not used. R.2 Reduced clearances (see )

33 age 33 of 78 S ANNEX S, ROCEDURE FOR IMULSE TESTING (see ) S.1 Test equipment No connection to the telecommunication network. S.2 Test procedure S.3 Examples of waveforms during impulse testing T ANNEX T, GUIDANCE ON ROTECTION AGAINST INGRESS OF WATER (see 1.1.2) U ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION (see ) Class III equipment. V ANNEX V, AC OWER DISTRIBUTION SYSTEMS (see 1.6.1) V.1 Introduction Class III equipment, supplied by the SELV provided by the certified power adapter. V.2 TN power distribution systems W ANNEX W, SUMMATION OF TOUCH CURRENTS W.1 Touch current from electronic circuits No touch current summation. W.1.1 Floating circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause C.1) X.1 Determination of maximum input current Class III equipment. X.2 Overload test procedure Y ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see ) Y.1 Test apparatus...: Not used. Y.2 Mounting of test samples...: Y.3 Carbon-arc light-exposure apparatus...:

34 age 34 of 78 Y.4 Xenon-arc light exposure apparatus...: Z ANNEX Z, OVERVOLTAGE CATEGORIES (see and Clause G.2) AA ANNEX AA, MANDREL TEST (see ) BB ANNEX BB, CHANGES IN THE SECOND EDITION

35 age 35 of 78 Contents General : A11: A1:2010 CENELEC COMMON MODIFICATIONS Add the following annexes: Annex ZA (normative) Normative references to international publications with their corresponding European publications Annex ZB (normative) Special national conditions Delete all the country notes in the reference document according to the following list: Note Note 2 & Note Note Note Note 4, 5 & Note Note Note Note Note Note 2 & Note Note Note Note Note Note Note 1 & Note Note Note Note 3 & Note 1 6 Note 2 & Note Note Note Note Note 7.1 Note Note 7.3 Note 1 & 2 G.2.1 Note 2 Annex H Note 2 General Delete all the country notes in the reference document (IEC :2005/A1:2010) according to the following list: 1.3.Z Note Note Note 2 EE.3 Note Add the following subclause: 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. NOTE Z1 A new method of measurement is described in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 1: General method for one package equipment, and in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Guidelines to associate sets with headphones coming from different manufacturers Add the following NOTE: NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC In addition, for a ORTABLE SOUND SYSTEM, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss.

36 age 36 of Replace the subclause as follows: Basic requirements To protect against excessive current, short-circuits and earth faults in RIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault protection may be provided by protective devices in the building installation; c) it is permitted for LUGGABLE EQUIMENT TYE B or ERMANENTLY CONNECTED EQUIMENT, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for LUGGABLE EQUIMENT TYE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet This subclause has been declared void Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in parentheses Replace IEC 53 by H05 RR-F ; IEC 52 by H03 VV-F or H03 VVH2-F ; IEC 53 by H05 VV-F or H05 VVH2-F2. In Table 3B, replace the first four lines by the following: Up to and including 6 0,75 a) Over 6 up to and including 10 (0,75) b) 1,0 Over 10 up to and including 16 (1,0) c) 1,5 In the conditions applicable to Table 3B delete the words in some countries in condition a). In NOTE 1, applicable to Table 3B, delete the second sentence In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Over 10 up to and including 16 1,5 to 2,5 1,5 to 4 Delete the fifth line: conductor sizes for 13 to 16 A Replace the existing NOTE by the following: NOTE Z1 Attention is drawn to: 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artifical optical radiation). Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC.

37 age 37 of 78 Annex H Bibliography Replace the last paragraph of this annex by: At any point 10 cm from the surface of the OERATOR ACCESS AREA, the dose rate shall not exceed 1 µsv/h (0,1 mr/h) (see NOTE). Account is taken of the background level. Replace the notes as follows: NOTE These values appear in Directive 96/29/Euratom. Delete NOTE 2. Additional EN standards. ZA NORMATIVE REFERENCES TO INTERNATIONAL UBLICATIONS WITH THEIR CORRESONDING EUROEAN UBLICATIONS

38 age 38 of 78

39 age 39 of 78

40 age 40 of 78

41 age 41 of 78 ZB SECIAL NATIONAL CONDITIONS In Denmark, certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socketoutlets In Norway and Sweden, for requirements see and 7.3 of this annex In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in CLASS I LUGGABLE EQUIMENT TYE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) In Finland, Norway and Sweden, the third dashed sentence is applicable only to equipment as defined in of this annex In Finland, Norway and Sweden, CLASS I LUGGABLE EQUIMENT TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan" In Norway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag

42 age 42 of 78 In Norway and Sweden, the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in Norwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN ). NOTE In Norway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kv r.m.s., 50 Hz or 60 Hz, for 1 min. Translation to Norwegian (the Swedish text will also be accepted in Norway): Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr og er tilkoplet et kabel-tv nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-tv nettet installeres en galvanisk isolator mellom utstyret og kabel- TV nettet. Translation to Swedish: Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-tv nät kan i vissa fall medfıra risk fır brand. Fır att undvika detta skall vid anslutning av utrustningen till kabel-tv nät galvanisk isolator finnas mellan utrustningen och kabel-tv nätet In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIONARY EQUIMENT the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a. For CLASS II EQUIMENT the socket outlet shall be in accordance with Standard Sheet DKA 1-4a In Norway, for requirements see , and of this annex In Finland, Norway and Sweden there are additional requirements for the insulation. See and of this annex In Norway, for requirements see , and of this annex In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A.

43 age 43 of In the United Kingdom, to protect against excessive currents and short-circuits in the RIMARY CIRCUIT of DIRECT LUG-IN EQUIMENT, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT LUG-IN EQUIMENT, so that the requirements of 5.3 are met In Finland, Norway and Sweden, there are additional requirements for the insulation, see and of this annex In Switzerland, supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV lug Type 15 3+N+E 250/400 V, 10 A SEV lug Type 11 L+N 250 V, 10 A SEV lug Type 12 L+N+E 250 V, 10 A In general, EN applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV lug Type 25 3L+N+E 230/400 V, 16 A SEV lug Type 21 L+N 250 V, 16 A SEV lug Type 23 L+N+E 250 V, 16 A In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or EN In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIMENT provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN

44 age 44 of In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a standard plug in accordance with Statutory Instrument 1768: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. NOTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525: National Standards Authority of Ireland (section 28) (13 A lugs and Conversion Adaptors for Domestic Use) Regulations In Switzerland, for requirements see of this annex In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is: 1,25 mm 2 to 1,5 mm 2 nominal cross-sectional area In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT LUG-IN EQUIMENT shall be assessed to BS 1363: art 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, and 12.17, except that the test of is performed at not less than 125 C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply In Ireland, DIRECT LUG-IN EQUIMENT is known as plug similar devices. Such devices shall comply with Statutory Instrument 526: National Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, In Finland, Norway and Sweden TOUCH CURRENT measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIONARY LUGGABLE EQUIMENT TYE A that is intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected ROTECTIVE EARTHING CONDUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE ERSON; STATIONARY LUGGABLE EQUIMENT TYE B; STATIONARY ERMANENTLY CONNECTED EQUIMENT.

45 age 45 of In Finland, Norway and Sweden, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirements for the insulation consisting of an insulating compound completely filling the casing, so that CLEARANCES and CREEAGE DISTANCES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTINE TESTING for electric strength during manufacturing, using a test voltage of 1,5 kv In Finland, Norway and Sweden, the exclusions are applicable for ERMANENTLY CONNECTED EQUIMENT, LUGGABLE EQUIMENT TYE B and equipment intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected ROTECTIVE EARTHING CONDUCTOR and is provided with instructions for the installation of that conductor by a SERVICE ERSON. 7.2 In Finland, Norway and Sweden, for requirements see and of this annex. The term TELECOMMUNICATION NETWORK in being replaced by the term CABLE DISTRIBUTION SYSTEM. 7.3 In Norway and Sweden, for requirements see and of this annex. 7.3 In Norway, for installation conditions see EN :2005.

46 age 46 of TABLE: List of critical components Object/part No. ower adapter (for model SC900) Manufacturer/ trademark owertron Electronics Corp. Type/model Technical data Standard (Edition / year) A SI100 Input: Vac, 50-60Hz, 0.3A MAX., Class II, Tma: 40 C. Output: 5Vdc, 1A., The output complied with LS. IEC :2005 (2nd Edition) Mark(s) of conformity 1 ) CB (issue by TUV Rheinland, CB Ref Certificate No.: JTUV ) Docking (Optional) a) Various Various O/: 5Vdc, 1.5A, Tma: 50 C. The output complied with L..S. Laser Scanner Module LCD module Optoelectronics Co., Ltd. owertip Tech. Corp. Vibration Motor Chongqing Linglong Electronic Co.,Ltd. MDL-1000 H240320T- 031-L49Q Y0411A Vdc, 0.87 mw, Wavelength 650 nm Laser class 1 2.8, a-si "TFT type, with LED backlight design. 3Vdc, 90mA max.. EN : A11, IEC : 2005 (2nd Edition) IEC : 2007 TUV or CB or equivalent CB by UL Tested in the appliance. Tested in the appliance. Speaker Ω, 1 W Tested in the appliance. Enclosure Material Various Various HB or better. UL 94 UL WB Various Various V-1 min, min. 105 C. Backup battery (one provided) RC Corporation AE H 3.7V, 75mAh (Typical) / 70mAh (Minimum), Lithium-ion olymer UL 796 UL Tested in the appliance.

47 age 47 of 78 - Cell Advanced Electronics Energy Ltd - MOSFET Sino-Mos Technology Crop. - rotection IC Seiko Instruments Inc. AE Max Charging Voltage:4.5V, Max Charging Current: 58mA. SMS8205 VDSS: 20V, ID: 4A S-8261ABJMD- G3J-T2G V DSO1 : 8V max., V DSO2 : 28V max., I OE : 7uA, max.. I DN : 0.1uA max.. - WB Various Various V-1 min, min. 105 C. Battery ack - Cell (two provided) ETI CA Battery Inc. Sanyo Energy (U S A) Corp - MOSFET Alpha & Omega Semiconductor, Ltd. - rotection IC Seiko Instruments Inc. - TC (olyswitch) - Enclosure of battery pack Fuzetec Technology Co., Ltd. B UF463450F AON5802B S-8211C FLT70F 3.7Vdc, 1840mAh/6.8Wh Lithium-ion olymer Max Charging Voltage: 4.4V, Max Charging Current: 1940mA. V DS : 30Vdc, ID: 7.2A V DSO1 : 8V max., V DSO2 : 28V max., I OE : 5.5uA, max.. I DN : 0.2uA max.. 0.7A, 24Vdc, Tripping current 1.5A UL 1642 UL 796 UL 1642 EN Various Various HB or better. UL 94 UL - WB Various Various V-1 min, min. 105 C. UL ) An asterisk indicates a mark which assures the agreed level of surveillance Supplementary information: a) see acceptance conditions in General product information page 5. UL Tested in the appliance. Tested in the appliance. UL Tested in the appliance. UL Tested in the appliance. Tested in the appliance. TUV UL

48 age 48 of TABLE: Electrical data (in normal conditions) U (V) I (A) Irated (A) (W) Fuse # Ifuse (A) Condition/status Test on model SC900 5Vdc Vdc Vdc Test on model M1000 5Vdc Vdc Supplementary information: Maximum normal load (ower from adapter with battery charge for EUT) Maximum normal load (ower from docking with battery charge for EUT) Maximum normal load (ower from battery discharge) Maximum normal load (ower from docking with battery charge for EUT) Maximum normal load (ower from battery discharge) TABLE: discharge test Condition τ calculated (s) τ measured (s) t u 0V Comments TABLE: hazardous voltage (circuit) measurement test Transformer Location Maximum Voltage Voltage Limiting peak DC Component TABLE: SELV reliability test From Accessible art To Voltage Limiting Component Fault Maximum V pk / dc Duration (ms)

49 age 49 of TABLE: limited current circuit measurement Location Voltage (V) Current (ma) Comments TABLE: limited power source measurement Location Limits Measured Comments Backup battery Battery ack output (Normal) 100VA, 8A 2.934VA, 0.9A Uoc = 4.25V Battery ack output (B- to - short) Battery ack 100VA, 8A 5.372VA, 1.7A Uoc = 4.25V Battery ack output (Normal) 100VA, 8A 7.464VA, 2.4A Uoc = 4.25V Battery ack output (B- to - short) 100VA, 8A 9.693VA, 2.7A Uoc = 4.25V and TABLE: ground continue test Location resistant measures (Ω) comments TABLE: working voltage measurement test Location rms voltage peak voltage (V) Comments

50 age 50 of and TABLE: Clearance and creepage distance measurements Clearance (cl) and creepage distance (cr) at/of/between: Functional: U peak (V) U r.m.s. (V) Required cl (mm) cl (mm) Required cr (mm) Basic/supplementary: Reinforced: Supplementary information: cr (mm) TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: U peak (V) U rms (V) Test voltage (V) Required DTI (mm) Supplementary information: DTI (mm)

51 age 51 of TABLE: Batteries The tests of are applicable only when appropriate battery data is not available -- Is it possible to install the battery in a reverse polarity position? Customized connector used for battery pack. Backup battery Max. current during normal condition Max. current during fault condition main board (Bto - short) Max. current during fault condition (U1105 in 4 to in 3 short) Battery ack Max. current during normal condition Max. current during fault condition main board (U2 in 1, 2 to 5, 6 short) Non-rechargeable batteries Meas. current Manuf. Specs. Rechargeable batteries Discharging Unintentional Charging Discharging Reversed charging charging Meas. current Manuf. Specs. Meas. current Manuf. Specs. Meas. current Manuf. Specs A 0.07 A A 0.14 A A 0.07 A A 0.14 A A 0.07 A A 1.1 A A 0.92 A A 1.1 A A 0.92 A -- --

52 age 52 of TABLE: Batteries The tests of are applicable only when appropriate battery data is not available -- Is it possible to install the battery in a reverse polarity position? Customized connector used for battery pack. Max. current during fault condition (U1101 in 5 to in 15 short) Non-rechargeable batteries Meas. current Manuf. Specs. Rechargeable batteries Discharging Unintentional Charging Discharging Reversed charging charging Meas. current Manuf. Specs. Meas. current Manuf. Specs. Meas. current Manuf. Specs A 1.1 A Note: See appended table 5.3 in detail. Test results: - Chemical leaks No Chemical leaks. - Explosion of the battery No Explosion. - Emission of flame or expulsion of molten metal No flam or molten. Verdict - Electric strength tests of equipment after completion of tests No isolation requirement. Supplementary information:

53 age 53 of TABLE: Thermal requirements Supply voltage (V)... See below. Ambient T min ( C) Ambient T max ( C) Maximum measured temperature T of part/at: T ( C) Allowed T max ( C) 1) for EUT (ower from power adapter with battery pack charging) 2) for EUT (ower from docking with battery pack charging) 3) for EUT (ower from battery pack) Supply voltage (V) 5Vdc 5Vdc 3.7Vdc -- Ambiemt 1) Tma=50 o C (24.3 o C) 2) Tma=50 o C (23.2 o C) 3) Tma=50 o C (24.4 o C) WB under U WB under U WB under U anel body Motor body Battery pack body Backup pack bady Enclosure inside near battery Enclosure outside near battery ower Adapter Supply voltage (V) 90Vac 264Vac -- Ambiemt Tma=50 o C (25.3 o C) Tma=50 o C (25.3 o C) -- WB under U C1 body T1 coil T1 core CY1 body Enclosure inside near T Enclosure outside near T Supplementary information: Temperature T of winding: t 1 ( C) R 1 (Ω) t 2 ( C) R 2 (Ω) T ( C) Allowed T max ( C) -- Insulation class Supplementary information:

54 age 54 of 78 Comments The temperatures were measured under worst case normal mode defined in and as described in subclause and at voltage as described above. The max. ambient temperature T max is defined at 50.Therefore the maximum temperatures measured are recalculated Winding components: ower adapter - Class A Tmax = 120 C - 10 C = 110 C (T1) EUT Components with: User accessible area: - max. absolute temp. of 105 Tmax (Battery pack & Backup pack) = max. absolute temp. of 105 Tmax (WB, Motor) = 105 ower adapter - max. absolute temp. of 105 Tmax (WB, Capacitor) = max. absolute temp. of 125 Tmax (Capacitor) = 125 EUT User accessible area: - External enclosure which may be touch temp. 95 Tmax = 95 ower adapter - External enclosure which may be touch temp. 75 Tmax = TABLE: Ball pressure test of thermoplastic parts art Allowed impression diameter (mm)...: 2 mm Test temperature ( C) Impression diameter (mm) Supplementary information: 4.7 TABLE: Resistance to fire art Manufacturer of material Type of material Thickness (mm) Flammability class Evidence Supplementary information:

55 age 55 of TABLE: touch current test Condition switch e switch on switch off reverse on reverse off Comment TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Functional: Voltage shape (AC, DC, impulse, surge) Test voltage (V) Breakdow n Yes / No Basic/supplementary: Reinforced: Supplementary information: 5.3 TABLE: Fault condition tests Component No. Vibration Motor Backup pack bady Battery pack V+ to V- Cell V+ to V- Overdischarge Test Battery pack B- to - Overcharge Test Ambient temperature ( C)... : 23 ower source for EUT: Manufacturer, model/type, output rating... : Fault Supply voltage (Vdc) Test time Fuse # Refer to Fuse current (A) Observation Locked 3V 7hrs No hazard, damage. Temperature varied during testing on: Coil = 52.4 C, Ambient = 23.9 C. Short 3.7V 30min Unit shutdown, no hazard, no damage. Short 3.7V 7hrs No hazard, Cell damage. Short 3.7V 7hrs No hazard, no damage. Battery pack -- 5V 7hrs No hazard, no damage.

56 age 56 of 78 Battery pack B- to - Main board U1105 pin 4 to 3 Battery pack body Battery pack V+ to V- Cell V+ to V- Overdischarge Test Battery pack U2 in 1, 2 to 5, 6 Overcharge Test Short 5V 7hrs No hazard, no damage. Short 5V 7hrs No hazard, no damage. Short 3.7V 30min Unit shutdown, no hazard, no damage. Short 3.7V 7hrs No hazard, Cell damage. Short 3.7V 7hrs No hazard, no damage. Battery pack -- 5V 7hrs No hazard, no damage. Battery pack U2 in 1, 2 to 5, 6 Main board U1101 in 5 to 15 Supplementary information: Short 5V 7hrs No hazard, no damage. Short 5V 7hrs No hazard, no damage.

57 age 57 of 78 hotos: Model SC900 & M1000

58 age 58 of 78 Model SC900 Model M1000

59 age 59 of 78 Model SC900 & M1000

60 age 60 of 78 Model SC900

61 age 61 of 78

62 age 62 of 78

63 age 63 of 78

64 age 64 of 78

65 age 65 of 78 Model M1000

66 age 66 of 78

67 age 67 of 78

68 age 68 of 78

69 age 69 of 78 Model SC900 & M1000

70 age 70 of 78 Laser Scanner Module

71 age 71 of 78

72 age 72 of 78 Backup Battery

73 age 73 of 78

74 age 74 of 78 Battery ack

75 age 75 of 78

76 age 76 of 78

77 age 77 of 78

78 age 78 of 78