CR /Fusion. BEETLE /FUSION Side Combo. Operating Manual

Transcription

1 CR /Fusion BEETLE /FUSION Side Combo Operating Manual

2 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability; technical modifications possible. Copyright Wincor Nixdorf International GmbH, 2011

3 CR /Fusion BEETLE /FUSION Side Combo Operating Manual Edition Sept 2011

4 Contents Contents Manufacturer s Certification... 1 Tested Safety... 1 FCC-Class A Declaration... 2 BSMI (EMC for Taiwan)... 2 Introduction... 2 Symbols used in this guide... 2 Important safety precautions... 3 Installation notes... 3 General safety precautions... 3 Installation... 5 Removing the packaging... 5 Installing side combo onto panel PC module... 5 Installation instruction # Installation instruction # Smart card reader Card Insertion Cleaning Magnetic swipe card reader Swiping the card Cleaning Fingerprint reader Operating fingerprint reader Cleaning BEETLE /FUSION Side Combo Operating Manual C

5 Contents Specifications C BEETLE /FUSION Side Combo Operating Manual

6

7 Manufacturer s Certification Manufacturer s Certification The device complies with the requirements of the EEC directive 2004/108/EC with regard to Electromagnetic compatibility and 2006/95/EC Low Voltage Directive. Therefore, you will find the CE mark on the device or packaging. Tested Safety The POS system has been provided with the symbol for Tested Safety. In addition, the device has received the UL symbol and cul symbol. This product is intended to be Listed Accessory, supplied by a UL Listed product, POS Terminal model BEETLE series C BEETLE /FUSION Side Combo Operating Manual 1

8 Manufacturer s certification FCC-Class A Declaration This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Modifications not authorized by the manufacturer may void user s authority to operate this device. This class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme à la norme NMB- 003 du Canada. BSMI (EMC for Taiwan) The device complies with the requirements of the BSMI (Bureau of Standards, Metrology and Inspection, Ministry of Economic Affairs) directive CNS14348 with regard to Electromagnetic compatibility with the limits for a Class B product. 2 BEETLE /FUSION Side Combo Operating Manual C

9 Introduction Introduction This operating manual provides you with the information you require to install the side combo onto the Beetle /Fusion system as well as the instruction to operate the side combo. Symbols used in this guide - Text following this mark represents an item in a list. Text in quotation marks contains references to other chapters or sections in this document. Paragraphs following this symbol are actions to be performed in the specific order. Text following this symbol has to be given special attention in order to avoid damage or injury. i This symbol identifies paragraphs which contain general notes to facilitate use of the device and help avoid operating errors. 2 BEETLE /FUSION Side Combo Operating Manual C

10 Introduction Important safety precautions Please read the following notes carefully before doing any work on the device. Installation notes - When installing the device and/or doing any work on it, make sure that it is disconnected from the power. General safety precautions This device complies with the relevant safety regulations for information processing equipment. - Note the warning and information labels on the device. - The device is equipped with a safety-tested power cable, which must be connected only to a grounded outlet. - Always hold the plug when removing the power cable. Never pull the cable itself. - Have damaged power cables replaced immediately. - If the display element is damaged and the liquid crystal solution leaks out onto your hands or clothing, please wash your hands or clothing immediately under running water for at least 15 minutes, using soap or alcohol. If the liquid comes into contact with your eyes, consult a medical doctor immediately. - Make sure that there is always free access to sockets used or to the electrical circuit-breakers of the house installation C BEETLE /FUSION Side Combo Operating Manual 3

11 Introduction - In case of an emergency (e.g. damaged cabinets, control or power cables, liquids or foreign objects in the device), switch off the device immediately and inform the customer service responsible for you. - During the thunderstorm, data transmission lines must not be connected or disconnected. - Only use accessories and extension components that have been approved by us. Nonobservance can result in damage to the system or violations of regulations concerning safety, radio interference and ergonomical requirements. - To clean the device only use cleaning agents approved by Wincor Nixdorf International GmbH. Repairs Repair work may only be carried out by authorized personnel. Unauthorized opening of the device or repair work carried out improperly could result in considerable danger to the user. In case of noncompliance, Wincor Nixdorf International GmbH excludes all liability. 4 BEETLE /FUSION Side Combo Operating Manual C

12

13 Installation Installation This chapter describes the steps to be taken to install the side combo onto the system. Removing the packaging Remove the packing material of the system or the modules ordered. Dispose of the packaging which is no longer needed according to the regulations of your country. Installing side combo onto panel PC module Side combo module C BEETLE /FUSION Side Combo Operating Manual 5

14 Installation There are 2 sets of installation instructions to install the side combo, please ensure that you are following the correct installation instructions!! To determine which set of installation instructions to be referred to, please check if the following cable is inclusive in the side combo kit that you purchased: If the cable is inclusive as part of the side combo kit, refer to installation instruction #1 If the cable is not inclusive as part of the side combo kit, refer to installation instruction #2 6 BEETLE /FUSION Side Combo Operating Manual C

15 Installation Installation instruction #1 Pry at the location å and gently push the side cover downward ç to disengage the side cover from the panel PC (see picture below). Side cover ç å C BEETLE /FUSION Side Combo Operating Manual 7

16 Installation Turn the panel PC to assess its rear, slide the cable cover to the right to remove the cover (see picture below). Connect the side combo cable to the RJ45 connector å at the rear panel and route the cable from the rear panel from inside out to the side combo in order to connect the power connector ç and data connector é to their respective connectors on the side combo. Power connector ç Data connector é RJ45 connector å 8 BEETLE /FUSION Side Combo Operating Manual C

17 Installation RJ45 connector å Opening to route the power connector ç and data connector é to side combo C BEETLE /FUSION Side Combo Operating Manual 9

18 Installation Ensure that the power connector and data connector are connected correctly on the side combo (see picture below). Data connector Power connector 10 BEETLE /FUSION Side Combo Operating Manual C

19 Installation Insert the side combo onto the side opening of the panel PCå, secure the 2 screws from the back of the system ç (see picture below). Front view å ç C BEETLE /FUSION Side Combo Operating Manual 11

20 Installation Rear view 12 BEETLE /FUSION Side Combo Operating Manual C

21 Installation Installation instruction #2 Pry at the location å and gently push the side cover downward ç to disengage the side cover from the panel PC (see picture below). Side cover ç å C BEETLE /FUSION Side Combo Operating Manual 13

22 Installation When the side cover is disengaged, you will be able to locate the combo reader cable as installed in the system (see picture below). Combo reader cable Pull out the combo reader cable from the bezel (see picture below). Pull out the combo reader cable 14 BEETLE /FUSION Side Combo Operating Manual C

23 Installation Untwist the cable before connecting the cable into side combo (see picture below) C BEETLE /FUSION Side Combo Operating Manual 15

24 Installation Connect cable onto side combo (see picture below). Connect cable onto side combo 16 BEETLE /FUSION Side Combo Operating Manual C

25 Installation Mount the side combo onto the system and tighten the 2 screws (see picture below). Tighten 2 screws C BEETLE /FUSION Side Combo Operating Manual 17

26 Smart card reader Smart card reader Card Insertion When you insert the card, you should make sure that the card is in the correct position (see arrow in picture below). Insert the card completely with the smart chip facing up, until the green light of the LED on the side combo turns red. LED light 18 BEETLE /FUSION Side Combo Operating Manual C

27 Smart card reader Cleaning The cleaning of the smart card reader has to be done with the help of a cleaning card. Make sure that no dirt arrears are in the card introduction slot. Otherwise clean the card introduction slot with a soft brush. Depending on the site conditions, it is suggested that a cleaning is required after approximately transactions. If it is necessary, clean it more frequently. Take the cleaning card out off the packing and drip off the cleaning card (this cleaning card is only usable for a short time)! Insert half the cleaning card into the card s slot as shown in the picture below. The arrow on the cleaning card should show forward so that the magnet head reader will be cleaned. The chip unit is maintenance-free and need not to be cleaned. Take out the cleaning card. Repeat this procedure several times. The smart card reader will be damaged if cleaned incorrectly C BEETLE /FUSION Side Combo Operating Manual 19

28 Magnetic swipe card reader Magnetic swipe card reader Swiping the card When you insert the card, you should make sure that the magnetic stripe is in the correct position. Ensure that the card is aligned to the magnetic swipe card reader s slot. 20 BEETLE /FUSION Side Combo Operating Manual C

29 Magnetic swipe card reader Swipe the card in top down direction with the magnetic stripe facing backwards and the left edge of the card constantly sliding against the guide of the reader. Card guide Swipe card in this direction The magnetic card reader cannot read the card information unless you swipe the card through the slot in one smooth and quick motion C BEETLE /FUSION Side Combo Operating Manual 21

30 Magnetic swipe card reader Cleaning The magnetic card reader is cleaned with a cleaning card. Make sure that no dirt remains in the card insertion slot. (If necessary, clean the card insertion slot with a brush). You can clean the read head when the device is switch on or switch off. Cleaning interval: every 20,000 transactions Cleaning material: Cleaning card Universal or ID card reader Cleaning process: Remove the cleaning ID card from its packaging. The cleaning card can only be used for a brief period as it is pre-saturated cleaning card which dries out after removal from its packaging. Swipe the cleaning card through the card slot like the regular ID card. Repeat this a few times. Dispose of the cleaning card. 22 BEETLE /FUSION Side Combo Operating Manual C

31 Fingerprint reader Fingerprint reader Operating fingerprint reader Place your finger on the surface of the fingerprint reader (see picture below). Scanning of fingerprint Hold and follow the instruction on the screen to complete the fingerprint scanning process C BEETLE /FUSION Side Combo Operating Manual 23

32 Fingerprint reader To achieve optimal fingerprint recognition accuracy when enrolling and authenticating, 1. Place the entire pad of your finger -- not just the tip or the side of your finger -- in the center of the oval window of the fingerprint reader, as shown in the picture above. 2. Apply steady, even pressure on the oval window. Do not roll or swipe your finger. 3. Hold your finger on the oval window until you see the light under the window blink. This indicates that the fingerprint reader has scanned your fingerprint. (You may find that this process takes longer than normal when your skin is dry). 4. When the light blinks, lift your finger from the oval window. Depending on how your fingerprint reader is configured, you may also hear a sound along with the blink of the light. To protect against the risk of bodily injury, fire, or damage to the fingerprint reader: o o o o o Do not rub the oval window with an abrasive material, including paper. Do not poke the oval window coating with your fingernail or with any other item, such as a pen. Do not submerge the fingerprint reader in liquid. Do not spray liquid on the fingerprint reader or allow liquid to drip inside. Do not use the fingerprint reader if it has incurred damage, such as a cracked. 24 BEETLE /FUSION Side Combo Operating Manual C

33 Fingerprint reader Cleaning The condition of the fingerprint reader affects its ability to obtain a good quality scan of a fingerprint. To maintain the fingerprint reader, the oval window should be cleaned periodically as follows: Press the sticky side of a piece of adhesive cellophane tape across the oval window, and then peel it away, as shown in the picture above C BEETLE /FUSION Side Combo Operating Manual 25

34 Fingerprint reader Specifications General Model Name CR /Fusion Electrical Voltage 5V ±5% Current 500mA (maximum) Interface Type USB 2.0 Connector RJ45 (proprietary) Environmental Operating +5 to +40 o C, Transport -25 to +60 o C, Storage +5 to +40 o C, Certifications EMC Product Safety CE CB, UL, GS-TUV 26 BEETLE /FUSION Side Combo Operating Manual C

35 Fingerprint reader Magnetic Swipe Reader Card Standard 1) ISO7811 2) ISO JIS X6301/X6302 Coercivity Card feed direction Card operation speed 300 Oe ~ 4000 Oe Forward only 10cm ~ 140 cm/sec (4 ~ 55 ips) Card thickness 0.25 to 1.25 mm Number of tracks 1) Track 1,2 & 3 (single-head) 2) Track 1 & 2, JIS2 (dual-head) Smart Card Reader Card Acceptor IC Card Standard Friction type CPU card: Comply with ISO7816-1,2,3 T=1 and T=0 protocol Approval PC/SC 1.0 Fingerprint Reader Memory card: 4404, 4418/28, 4432/42, 4406/36/5536, I2C Pixel resolution Scan data 512 dpi 8-bit grayscale C BEETLE /FUSION Side Combo Operating Manual 27

36 Published by Wincor Nixdorf Pte Ltd 2, Kallang Sector Singapore Part No.: C