In-Site Motion Webcam

Transcription

1 In-Site Motion Webcam User s Manual Model IC825C

2 FCC STATEMENT IC825C This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult a service representative for help. Properly shielded and grounded cables and connectors must be used in order to comply with FCC emission limits. Micro Innovations is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user s authority to operate the equipment. Responsible party: Micro Innovations 400 Clearview Ave. Edison, NJ Telephone: 1(877) Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme NMB-003 du Canada. 2

3 Table of Contents Welcome Page 4 Installing your Webcam..... Page 5 Capturing Still Images and Video Clips Page 6 Motion Tracking Tool. Page 7 Helpful Hints Page 8 Troubleshooting and Technical Support. Page 9 3

4 Welcome Congratulations on the purchase of your Micro Innovations IN-SITE MOTION WEBCAM. The Micro Innovations IN-SITE MOTION WEBCAM is compatible with IBM and 100% compatible computers with an available USB port, and is supported by Windows 98SE, Windows ME, Windows 2000, Windows XP and Windows Vista. Motorized Motion Tracking rotate the webcam 180º horizontally and 60º vertically to capture your movements. Package contents: Motion Track Webcam (USB) Quick Installation Guide User s Manual Installation CD Warranty Information LED Indicator Lights when camera is in use 4

5 Installing Your Webcam Install Software First before attaching the webcam to your PC. In order for your webcam to function properly, you must install the DRIVER. You can install the Ulead software at a later time. Choosing the DRIVER Only Installation. This will install the basic software to operate your webcam. This will allow you to use your webcam will many popular Internet video chat applications. After installing the DRIVER, simply launch your favorite video chat program to begin use. During the installation you will be prompted to restart your PC. When instructed to connect your webcam, insert the USB connector into an available USB port on your PC. Wait until your PC has finished detecting your webcam. Your PC will make the proper settings to operate your webcam. Complete the webcam installation. To Uninstall the DRIVER: Click Start Programs Motion Track Webcam Uninstall To view the User s Manual for the Motion Track Webcam: Click Start Programs Motion Track Webcam User s Manual Frequently check for updated webcam software by visiting our website, To use the microphone connect the 3.5 mm connector to an available audio jack. 5

6 Capturing Still Images and Video Clips To capture still images and video clips, you must install the Ulead Photo Explorer 7.0 SE program. If you did not install the application during the initial driver installation, you can install the program by inserting the installation CD into your computer s CDROM drive and select the proper title. Follow the on-screen instructions to complete the installation. Once the Ulead Photo Explorer 7.0 SE is correctly installed, click Start Programs Ulead Photo Explorer 7.0 SE or click the icon located on your desktop to launch the application. Here you can capture, edit and organize your still images and video clips. Capturing Still Images To capture still images with your webcam launch Ulead Photo Explorer 7.0 SE and select File Twain Acquire Acquire now to launch the preview screen. You can also use the CTRL + N command to launch the Acquire Now function. Another way to capture still images is to select Video Capture Still Image. Capturing Video Clips To capture video with your webcam, launch the Ulead Photo Explorer 7.0 SE program and select Video Capture Video. Note your Motion Track Webcam will automatically focus and LED indicator will illuminate when in use. 6

7 Motion Tracking Tool To use the Motion Tracking Tool, you must first launch your favorite Internet chat application, Internet messaging program or Ulead Photo Explorer 7.0 SE. Once you can preview your image using the on-screen viewer, click the Motion Tracking Tool icon located in the lower right hand corner of your screen or click Start Programs Motion Track Webcam Motion Tracking Tool Capture Button Settings Menu Using the Motion Tracking Tool, you can easily control the tracking feature by selecting either the AUTO TRACK or MANUAL TRACK buttons. Use the ZOOM slider to manually zoom in (+) or out (-) The directional arrows will manually rotate your webcam 7

8 Helpful Hints The following hints will help you achieve the best results with your webcam: Webcam placement Position the webcam so that the subject is centered. Place the webcam on a steady surface Lighting Use sufficient lighting. Place the light source behind the camera and facing the subject. Maintain a consistent lighting environment, i.e. do not mix fluorescent and other light types. Do not aim the webcam directly at the light source. Maintenance Keep the webcam away from moisture and extreme temperature. Never use harsh or abrasive cleaners or organic solvents on the webcam or on any of its parts. Never disassemble or touch the inside of the webcam. 8

9 Troubleshooting and Technical Support Problem Resolution No capture device found error Make sure you have connected the webcam correctly into an available USB or try a different USB port on your PC. Camera not connected error Try removing the previous driver and reinstalling the software. There may be a conflict with previous camera/scanner software installed on your PC. You may need to remove the previous software before using this device. Webcam image is too dark (Black or green screen) Try removing the previous driver and reinstalling the software. For technical assistance, call toll free: or visit Technical Support hours of operation: Monday - Friday 8:30am to 7:00pm E.S.T. 9