A Cnoidal Approximation Wave Theory
|
|
|
- Lewis Daniels
- 9 years ago
- Views:
Transcription
1 A Cnoidal Approximation Wave Theory Rodney J. Sobey Department of Civil and Environmental Engineering, Imperial College London, London SW7 AZ, UK Engineering and Computational Mechanics, 56, -6, 5 June Abstract Periodic progressive waves in shallow to transitional water are described by a Cnoidal Approximation wave theory. The formulation is analytical and largely classical. Periodic waves are assumed, so that the theory does not extend to solitary waves. The solution is completed numerically, as a problem in nonlinear optimisation. The suitability of the theory in shallow to transitional water is demonstrated to 88% of the limit wave height. Keywords Cnoidal waves, extreme wave kinematics, limit waves, nonlinear optimisation, numerical, progressive waves, short waves, steady wave theory, Stokes waves. Introduction The extreme wave credibility of analytical shallow water(cnoidal) wave theory to fifth order extends only to about 5% of the limit wave height in very shallow water, rising to about 7% in transitional water. Increasing the order of approximation is expected to result in improvements in the predictive credibility. The analytical expressions for the coefficients are already very long at fifth order, and a higher order analytical theory will further increase the opportunity for transcription errors that have so compromised analytical theories in the literature. This is not a pragmatic approach. For deep water (Stokes) waves, analytical theories to fifth order have credibility much closer to the limit wave. This credibility has been further enhanced by a hybrid analyticalnumerical extension of the Stokes approximation where the analytical formulation follows
2 z L η MWL H X=x-Ct h w U=u-C Figure : Definition sketch for steady progressive wave. the Stokes approach with the unknowns of the theory assigned numerically rather than analytically. Such a Stokes approximation has alternatively been called stream function wave theory or Fourier approximation wave theory. These Stokes approximation theories have had considerable success. By default almost, their domain of applicability has been pushed into the shallow water region through very significant increases in the order of approximation. A cnoidal approximation theory is here introduced. It is a hybrid analytical-numerical extension of the cnoidal theory where the analytical formulation follows the cnoidal approach with the unknowns of the theory assigned numerically rather than analytically. There are a number of obvious parallels with the Stokes approximation approach, but equally a number of issues unique to the shallow water context. The theory is formulated and demonstrated below. Its credibility at very moderate order extends to about 88% of the limit wave. Mathematical Formulation of Steady Wave Theory Progressive waves of permanent form are steady in a frame of reference moving with the crest at the phase speed C. Accordingly, it is convenient to adopt a moving (X = x Ct,z) reference frame (see Figure ) that is located at the mean water level (MWL) and that moves at speed C with the wave crest. In this (X,z) frame, the flow is steady, whereas in the fixed (x, z, t) reference frame, the flow is unsteady. Periodic waves and incompressible and irrotational flow are assumed. The mathematical formulation may be presented in terms of the Euler equations, the velocity potential function, the stream function or the complex potential function. The choice of the stream function Ψ(X,z) in the steady frame has some minor advantage in
3 the representation of the kinematic free surface boundary condition (as it does not require time or spatial derivatives of the primitive variables η and Ψ). In terms of the stream function, the field equation representing mass conservation and irrotational flow is the Laplace equation Ψ X + Ψ z = () where the velocity components (U = u C, w) are ( Ψ/ z, Ψ/ X). Momentum conservation throughout the fluid is represented by the irrotational Bernoulli equation in the steady frame ( U +w ) + p +gz = R () ρ where R is the Bernoulli constant in the steady frame. In terms of the stream function, the complete boundary constraints are as follows. () The bottom boundary condition (BBC), representing no flow through the horizontal bed, is Ψ(X, h) = or Ψ(X,z) = at z = h (3) () The kinematic free-surface boundary condition(kfsbc), representing no flow through the free surface at η(x), is Ψ(X,η(X)) = Q or Ψ(X,z) = Q at z = η(x) (4) where Q is the constant volume flow rate per unit width under the steady wave. Q is numerically positive and this flow is in the negative X direction. The zero datum for the stream function was established by the BBC. (3) The dynamic free surface boundary condition (DFSBC), representing constant atmospheric pressure on the free surface, is ( U +w ) +gη = R at z = η(x) (5) which follows directly from the irrotational Bernoulli equation in the steady frame. (4) The wave is periodic. The periodic lateral boundary conditions (PLBC) are Ψ(X+L,z) = Ψ(X,z), η(x+l) = η(x) (6) where L is the wave length. Solitary waves with infinite L are excluded. (5) The wave height is defined as H = η() η(l/) (7) 3
4 (6) Mass conservation requires an invariant mean water level (MWL) such that L/ η(x)dx = (8) Inprinciple,theunknownsofasteadywavesolutionwillbethestreamfunctionΨ(X,z), the water surface profile η(x), the wave length L, the current or mean fluid speed Ū at any elevation that is always submerged below the trough, the volume flux Q and the Bernoulli constant R. In specific nonlinear wave theories, the stream function, the water surface profile and the wavelength are represented in terms of other parameters, which take their place as unknowns in the theory. The given parameters defining a steady wave solution are generally the wave height H, the water depth h, the wave period T(= π/ω) and either the co-flowing Eulerian current U E or the wave-averaged mass transport velocity or Stokes drift U S. 3 Dispersion Relationship Steady wave theory seeks to predict the flow in the moving and steady flow reference frame. In this frame, it will predict both the current Ū and the volume flow rate Q under the steady wave, respectively U = L L U(X,z)dX, Q = η(x) h U(X,z)dz (9) In the U definition, the elevation z can be any elevation at or below the trough; z = h is often convenient. In the Q definition, the location X can be any location, as the flow is steady. Steady wave theory does not predict the actual speed C of this frame. C is measured in the fixed and unsteady frame, and is dependent also on background flow conditions. The current in the steady frame is U and the steady frame is moving at speed C, so that the current in the fixed and unsteady frame is U E = U+C. Similarly, the depthaveraged mass transport velocity in the steady frame is Q/h, so that the depth-averaged mass transport velocity in the fixed and unsteady frame is U S = Q/h+C. Transformation between the frames requires knowledge of both the current and the wave period. (i) Where the Eulerian current U E is known, the phase speed is C = U +U E () The depth-averaged mass transport velocity or Stokes drift U S is then available from C = Q h +U S () 4
5 (ii) Where the depth-averaged mass transport velocity U S is known, Eq. predicts the phase speed. Eq. then becomes the definition equation for the Eulerian current. These alternative coordinate transformations are often called Stokes first and second definitions of phase speed. In either case, the space and time periodicity of the progressive wave of permanent form requires C = L () T as a simultaneous equation. The wave period T is the (absolute) period measured in a fixed reference frame, e.g., by a wave staff or buoy at a fixed position. Similarly, U E is the time-mean Eulerian current in the fixed reference frame, as measured by a current meter deployed at a fixed position below the wave trough. Taken together, (i) Eqs. and where the Eulerian current is known - L T = U +U E (3) (ii) or Eqs. and where the depth-averaged mass transport velocity is known - L T = Q h +U S (4) relate the space and time periodicity. This is the dispersion relationship for the progressive wave. Whichever equation is not used becomes the definition equation for the other current. With L, U and Q predicted by a steady wave theory, the details will vary with the wave theory. 4 Kinematics Following (Lamb 93, p.43-4) and a number of subsequent analytical theories (Keller 948, Laitone 96, Fenton 979, Sobey ), a suitable shallow-water focussed solution of the field Laplace Eq. is the truncated series in which Ψ(X,z) = (gh 3 ) / N k= Ψ k (χ,ζ), Ψ k (χ,ζ) = ( ) k(+ζ)k+ f k (χ) (5) (k+)! f (χ) = f(χ) and f k (χ) = α d dχ f k, k =,... (6) and N is the truncation order. The dimensionless independent variables are χ = α X h, ζ = z h (7) 5
6 where α = K(m)h (8) L in which K(m) is the Jacobian elliptic integral of the first kind with parameter m. The shallow-water focus is explicit in the α stretching of the horizontal independent variable in Eq. 7. Note that Eq. 5 exactly satisfies the bottom boundary condition (Eq. 3). The field equation (Eq. ) becomes, non-dimensionally, α Ψ χ + Ψ ζ = Ψ Ψ Ψ Ψ α χ + ζ +α χ + ζ +...+α Ψ k Ψ k Ψ N Ψ N χ + ζ +...+α χ + ζ It follows from Eqs. 5 and 6 that Ψ / ζ = and (9) α Ψ k χ + Ψ k ζ, k =,,...N () identifying a Laplace field residual, α Ψ N / χ, at truncation. In a classical analytical small parameter expansion theory, strict truncation of all terms in the formulation at order N conveniently results in a vanishing Laplace field residual. A numerical theory imposes neither strict truncation at order N nor the expectation that contributions at progressively higher orders are routinely smaller in magnitude. A significant Laplace field residual is possible. This must be acknowledged in the problem formulation. In addition to the boundary constraints () through (6) (Eqs. 3 through 8), there must be added (7) The free surface Laplace condition Ψ X + Ψ z = U z w X = at z = η(x) () Because of the (+ζ) multiplier in the stream function (Eq. 5), the Laplace field residual is zero at the bed z = h, and largest at the water surface z = η(x). Eq. imposes a field constraint on the Laplace residual. In any steady wave theory, the most vulnerable aspect of the predicted kinematics is routinely the acceleration components Du/Dt and Dw/Dt Du Dt = U U X +w U z, Dw Dt = U w X +w w z The vulnerability stems from the quadratic terms on the right hand side together with the dependence on spatial derivatives of the velocity components, which are in turn spatial second derivatives of the stream function. These spatial derivatives are related through the mass conservation equation U X + w z = (3) 6 ()
7 and the irrotational flow constraint U z w X = (4) Eq.3isexactlysatisfiedbytheadoptionofastreamfunction. Eq.4becomestheLaplace field equation, as indicated in Eq.. A classical steady wave formulation does not include the velocity gradients. As suggested by Eq. 9 and the associated discussion, the inclusion of the irrotational flow constraint in the problem formulation (Eq. ) may benefit the predictive precision of the acceleration components for shallow water waves. Following a number of analytical theories (Keller 948, Laitone 96, Fenton 979, Sobey ), the function f(χ) in the stream function is represented as the truncated series f(χ) = A j cn j (χ;m) (5) j= and the water surface elevation as the truncated series η(χ) = B j cn j (χ;m), η(x) = hη(χ) (6) j= in which cn(χ;m) is the Jacobian elliptic cosine function. Note that the Eq. 8 definition for α results in Eqs. 5 and 6 exactly satisfying the periodic lateral boundary conditions (Eq. 6). There are peripheral suggestions in the solitary wave literature (e.g. Engevik 3) that infinite shallow water series solutions are divergent. Relevance to the present context is very tenuous. Firstly, solitary waves are specifically excluded as they are not periodic waves (Equations 6, 3, 4); solutions very close to m= are sought, but not at m= where K(m), α and L are infinite. Secondly, the adopted series (Equations 5, 5, 6) are not infinite but truncated at N. Minimising the truncation error (Equation ) is explicit in the problem formulation. The f k (χ) in Eq. 5 require recurring second derivatives, which are represented as f k (χ) = N+ j= A k j cn j (χ;m) in which [ A j] = [Aj ] and [ A k j ] [ (7) ] = α A k j F for k =...N where [ A k j] are (N+) coefficient vectors and F is a (N+) (N+) transformation matrix (see Appendix A) that provides the second derivative of cn j (χ;m). As a consequence of the analytical expression for d cn j (χ)/dχ (Eq. 56), each increment in k expands the row width of [ A k j] by one element. The first (k = ) row has active entries in columns through N+ and N+ trailing zeros, the second (k = ) row has active entries in columns through N+ and N trailing zeros,...and finally the row k = N+ has active entries in columns through N+ and no trailing zeros. 7
8 The dynamic free surface boundary condition requires also the velocity components U(X,z) = Ψ(X,z) z w(x,z) = Ψ(X,z) X = h k= = α h ( ) k(+ζ)k (k)! k= ( ) k(+ζ)k+ (k+)! and the free surface Laplace condition the velocity gradients where g k (χ) = d dχ f k(χ) = h k (χ) = d dχ f k(χ) = U z = h w X = α h j= j= A k j A k j k= f k (χ) (8) g k (χ) (9) ( ) k(+ζ)k (k )! f k(χ) (3) ( ) k(+ζ)k+ h k (χ) (3) (k+)! k= d dχ cnj (χ;m) = scd(χ;m) d dχ cnj (χ;m) = a k j cn j (χ;m) (3) j= a k j cn j (χ;m) (33) in which [ a k j] = [ A k j ] G, and [ a k j ] = [ A k j ] F (34) G has dimensions (N+) (N+) and F here has dimensions (3N+) (3N+). The function scd(χ) is scd(χ) = sn(χ) cn(χ) dn(χ) (35) The Jacobian elliptic functions sn(χ) and dn(χ) appear only in this product combination in the Cnoidal Approximation theory. The transformation matrix G is also listed in Appendix A. 5 The Cnoidal Approximation The unknown variables in a Cnoidal Approximation solution are m, α, U E or U S, Q, R, the A j coefficients for the stream function Ψ(χ,ζ) and the B j coefficients for the water surface η(χ), for j =,,...N, of which there are N+7. The problem formulation provides 3M +4 implicit algebraic and nonlinear equations in these N+7 unknowns, each equation being cast in the form j= f i (m,α,u E or U S,Q,R,A j,b j ) = (36) 8
9 in which m = m, Q = Q Uh and R = R C. The equations are those identified in Section, and additionally the Laplace residual Eq.. They define the wave height the mean water level f = η(x=) η(x=l/) H (37) f = L/ = K(m) L/ K(m) η(x) dx η(χ)dχ = j B j K(m) K(m) cn j (χ;m)dχ (38) = j B j I j the Eulerian current and the Stokes drift f 3 = L T U U E (39) f 4 = L T Q h U S (4) The kinematic free surface boundary condition (KFSBC) and the dynamic free surface boundary condition (DFSBC) are imposed along the free surface at M discrete nodes over X L/, a half wave profile. These discrete points are distributed as X i = ( ) i L, for i =,,...M (4) M to focus attention toward the crest where kinematic variations are most rapid for a cnoidal wave. The water surface elevation at X i is η i (Eq. 6). The kinematic free surface boundary condition (KFSBC) at each of the M free surface nodes is f +3i = Ψ(X i,η i )+Q for i =,,...M (4) and the dynamic free surface boundary condition (DFSBC) at each of the free surface nodes is f 3+3i = [ U (X i,η i )+w (X i,η i ) ] +gη i R for i =,,...M (43) Additionally, the free surface Laplace condition (Eq. ) at the same X i free surface nodes is f 4+3i = U w for i =,,...M (44) z X (Xi,η i ) (Xi,η i ) With U/ z w/ X scaled by the (+ζ) multiplier from zero at the bed to a maximum at the free surface, Eqs. 44 will impose the Laplace equation to excellent precision throughout the solution field. 9
10 and In the above f i equations, L = K(m)h α ([8]) U = L L = (gh) / j U(X, h)dx = (gh) / K(m) A j K(m) K(m) K(m) cn j (χ;m)dχ f(χ)dχ (45) = (gh) / j A j I j The definite integrals I j = K(m) K(m) follow analytically from the recurrence relationship cn j (χ;m)dχ (46) (j )mi j = (j )( m)i j +(j 3)( m)i j where I =, I = e+m and e = E(m) m K(m) (47) established from Gradshteyn & Ryzhik (965, 5.3()). E(m) is the Jacobian elliptic integral of the second kind with parameter m. There are 3M+4 of implicit algebraic equations in N+7 unknowns. The problem can be uniquely specified, for N=3,6,9,...for which M=3,5,7,..., but this does not provide a suitable algorithm. The choice of order N is restrictive and the spatial resolution M (through Eq. 4) of the free surface constraints is unlikely to be satisfactory. The solution of a set of 3M +4 simultaneous implicit nonlinear algebraic equations in N+7 unknowns, where M > N/3+, is a familiar problem in numerical analysis in the context of nonlinear optimisation. A solution is established by seeking a minimum value for an objective function of the N +7 unknowns. The nonlinear optimisation algorithm adopted was the trust region method (Conn et al. ), based of Equations 37 through 43. The least squares objective function was O(m,α,U E or U S,Q,R,A j,b j ) = f +...+f 4 + [ f f 3M+4] /M (48) such that each of the seven distinct physical contributions to the problem formulations (Eqs. 37 through 4 and 4 through 44) is similarly weighted. Moderately significant overspecification, choosing M principally to resolve the free surface boundary constraints, is physically advantageous. M = was routinely satisfactory. To ensure the same prominence for the separate contributions to the Equation 48 objective function, it is numerically essential that each contribution has the same physical
11 dimensions. This was achieved by non-dimensionalising every variable in the problem formulation by the shallow water length and time scales L = h, T = (h/g) / (49) respectively. A typical wave problem has 3 unknowns(at N =8, as subsequently adopted). Nonlinear optimisation in 3 dimensions may find mathematical solutions at local minima for the Equation 48 objective function. Identification of the unique physical solution requires some very careful attention to detail. Specific attention must be given to the initial solution estimate, to the convergence criterion, and to the predictions of field kinematics, especially acceleration. These issues are considered below. Routine experience consistently confirms that the dominant issue is the relative fidelity of the initial solution estimate. Numerical optimisation in so many dimensions can rarely survive a poor initial estimate. And linear or Airy wave theory provides a poor initial estimate, except for infinitesimal waves. Three strategies were adopted, in sequential order. (I) m, α, U E or U S, Q, R, and the coefficients A j,b j through A 5,B 5 were assigned from an existing analytical theory to fifth order (Sobey ). In the analytical theory, there are ij contributions at each order i, the coefficients being designated A ij and B ij respectively. The A j and B j were assigned as A j = 5 ε i A ij, B j = i= 5 ε i B ij (5) i= respectively, where ε = H/h. The initial estimates for A j,b j coefficients beyond A 5,B 5 were zero. (II) For extreme waves, the analytical theory to fifth order is not reliable and strategy I generally fails. The analytical solution will not provide reasonable initial solution estimates for wave heights in excess of about 5% of the limit wave in shallow water, rising to about 75% in transitional water (Sobey, Figure 8). For more extreme wave conditions, successful solutions were often achieved with initial solution estimates provided by prior solutions at gradually increasing wave height. Assume a sequence of solutions S(H), strictly S(H;h,T,ρ,M), where the parameters h, T, ρ and M are fixed. S represents in turn elements of the solution vector [m,α,u E or U S,Q,R,A j,b j ]. The strategy II initial solution estimate is S Initial = S (5) where S is the solution vector at the next highest wave height H at which there was a successful solution.
12 (III) Strategy II in turn also sometimes fails for the more extreme waves, especially in shallow water. The final strategy imposes a truncated Taylor series approximation. The strategy III initial solution estimate is S Initial = S + ds dh (H H ) (5) where ds/dh = (S S )/(H H ). As before the - subscript identifies the highest available successful solution. Similarly, - identifies the next to highest successful solution. Computations, at IEEE double precision, assigned convergence at a relative error in the non-dimensional objective function not exceeding, a choice suggested by preliminary numerical experiments. This is a very demanding convergence criterion, but the computational penalty was not excessive. 6 Predicted Kinematics A complete list of predictive equations for the wave kinematics is included as Appendix B. Figure compares predictions of the key kinematics from the Sobey () analytical cnoidal wave theory to fifth order (Cnoidal 5) with the present Cnoidal Approximation theory also at N=5 (Cnoidal Approximation 5 or CA 5) for a steady wave at depth h= m, period T= s, height H=.5 m and zero current, U E =. Part (a) shows the water surface elevation, part (b) the velocity components, and part (c) the acceleration components. The agreement is visually perfect, confirming the Cnoidal Approximation formulation and its coding implementation. The acceleration components are especially sensitive measures of predictive capability, as they involve double spatial differentiation of Ψ. Figure is a wave condition well within the validity range of the analytical theory (shown later in Figure 6); the dimensionless depth ω h/g is.8 and H/H Limit is.3, where H Limit is the Williams (985) prediction for the limit wave at the same dimensionless depth. There is nevertheless an important observation on the value of the Cnoidal Approximation theory, even at the same nominal order. Each theory involves compromises in the kinematic free surface boundary condition, the dynamic free surface boundary condition and the Laplacian residual. The extent of these compromises is explicitly included in the Eq. 48 objective function, or separately as the root-mean-square errors along the free surface: rms K = L/ L/ rms D = L/ L/ rms L = L/ L/ [Ψ(X,η)+Q] dx [ [ [ U (X,η)+w (X,η) ] ] +gη R dx U z w (X,η) X dx (X,η)] (53)
13 η(x) [m].4. Cnoidal 5 Cnoidal Approx (a) Water surface X [m] [u,w](x,η) [m/s] D[u,w]/Dt(X,η) [m/s ] (b) Velocity X [m] (c) Acceleration X [m] u(x,η) Analytical N=5 w(x,η) Analytical N=5 Figure : Analytical and Cnoidal Approximation Predictions at N =5 for h= m, H=.5 m, T= s, U E =. Analytical CA N=5 CA 7 CA 8 CA 9 CA rms K.93e-5 5.9e-7.48e-8.34e-8.58e e-7 rms D.e-4 3.8e-7.9e-8 6.6e-9 3.6e e-7 rms L.43e-7 5.7e-9 8.7e- 4.9e e-8 Table : Dimensionless Root-Mean-Square Errors for h= m, H=.5 m, T= s, U E =. Numerical evaluation of the integrals adopted the trapezoidal rule, over uniformly spaced points. In the analytical theory, the f k (χ) are truncated strictly at fifth order and the Laplace residual is identically zero. Table list the dimensionless rms errors for the wave conditions of Figure ; scaling adopted the Eq. 49 length and time scales. 3
14 Analytical CA N=5 CA 7 CA 8 CA 9 CA rms K.e- 4.5e e e e e-5 rms D.35e- 3.77e-4 8.3e e-5 5.5e-5 9.9e-5 rms L.4e-4 3.4e e-5.68e-5.85e-4 Table : Dimensionless Root-Mean-Square Errors for h= m, H=.5 m, T= s, U E =. Also listed in this table are the rms errors for Cnoidal Approximation solutions at N of 7 through. The numerical predictions at N of 7 through are visually identical with the N=5 solutions in Figure. The rms errors in Table are all very small and confirm the predictive capability of the analytical theory and each of the CA results. The trends nevertheless provide a useful commentary on the respective theories. As expected, the rms errors for CA 5 are significantly smaller than for the fifth-order analytical theory. For the analytical theory, the error (by definition) is of order ε 6 = (H/h) 6 =.44e-4; this is the order of magnitude for rms K and rms D. Error for the Cnoidal Approximation theory is somewhat different. In this case, order defines the truncation for f(χ)=f (χ) in the stream function (Eqs. 5 and 5) and for the water surface elevation η(x) (Eq. 6). Terms involving cn j (χ) for j exceeding N and up to N+ appear in the f k (χ), as outlined in the discussion following Eq. 7. The CA rms errors are impacted by the convergence criterion for the nonlinear optimisation only when the convergence criterion are not adequate; stable results were routinely achieved at the adopted relative error of in the objective function. The trend in the CA results in Table provides an excellent overview on the value of CA order. There is initially some apparent advantage in increasing the order, but this quickly reaches saturation. Further increases are of marginal value, and increasing rms errors become apparent. These increases are routinely associated with decreasingly robust solution convergence. Extensive numerical experience has suggested N =8 as an optimal choice for CA order. This N is deceptively small. Ψ, U and U/ z actually include terms to cn (N+), w, U/ X and w/ z terms to cn (N) and w/ X terms to cn (3N+). Figure 3 is a wave condition (h= m, H=.5 m, T= s, U E =; ω h/g=.8, H/H Limit =.79) well outside the validity range of the analytical theory (see Figure 6). As expected, the analytical predictions for velocity and especially acceleration are not credible. The Cnoidal Approximation predictions at N of 5 and 7 through were again visually identical. The CA 8 predictions are credible. They seem physically plausible and the rms errors, listed in Table, are suitably small. Note that the rms errors are rather larger for this nearer limit wave than was the case for the Figure wave, but the errors remain respectably small. The hybrid analytical-numerical Stokes/Fourier Approximation(FA) is well established, as well as the almost default extension of this FA theory into the shallow water domain at higher truncation orders. Higher orders may indeed push the apparent application of the 4
15 η(x) [m].5 Cnoidal 5 Cnoidal Approx. 8 [u,w](x,η) [m/s] (a) Water surface X [m] 4 u(x,η) Analytical N=8 w(x,η) Analytical N= (b) Velocity X [m] D[u,w]/Dt(X,η) [m/s ] (c) Acceleration X [m] Figure 3: Analytical and Cnoidal Approximation Predictions at N =8 for h= m, H=.5 m, T= s, U E =. FA theory into shallow water but it remains a Stokes approximation with optimal credibility in deeper water. Difficulties become most apparent in the extended flat trough of shallow water waves, where oscillations begin to appear in water surface predictions, rather more in velocity predictions and especially in acceleration predictions. Figure 4, for the Figure 3 wave conditions, shows these oscillations for the water surface profile predictions. Included are the CA 8 prediction from Figure 3, together with Fourier Approximation predictions (code from Sobey 989) at N= and N=5. At the scale of part (a), the oscillations are not especially visible in the η(x) predictions, though they can be detected in the FA acceleration predictions. The FA oscillations are clear in part (b) at expanded scale. The CA 8 prediction, even at expanded scale, remains well behaved and credible. The complementary roles of the present hybrid analytical-numerical Cnoidal Approximation (CA) in shallow water and the hybrid analytical-numerical Fourier Approximation (FA) in deep water was anticipated above. The temptation to push the CA theory to deeper water 5
16 η(x) [m] CA 8 FA FA X [m] (a) η(x) predictions η(x) [m] X [m] (b) η(x) at expanded vertical scale Figure 4: Cnoidal and Fourier Approximation Predictions for h= m, H=.5 m, T = s, U E =. Analytical CA N=5 CA 7 CA 8 CA 9 CA rms K 3.93e e-4.3e-4.3e e e-5 rms D 5.78e-3 7.9e-4.4e-4.4e-4 8.7e-5 5.3e-5 rms L.e-4 5.6e e-5.95e-5.48e-5 Table 3: Dimensionless Root-Mean-Square Errors for h= m, H=. m, T= s, U E =. is fortunately constrained by rapidly declining sensitivity to the Jacobian parameter m as m becomes very small. Figure 5 is a wave condition (h= m, H=. m, T= s, U E =; ω h/g=.8, H/H Limit =.85)intransitionalwaterandbeyondthevalidityrangeoftheanalyticaltheory (see Figure 6). That the analytical predictions for accelerations lack credibility requires close inspection of the acceleration traces. Du/Dt along the water surface oscillates twice below and then above the smoothly varying CA 8 prediction. Similarly Dw/Dt starts well abovetheca8traceatthecrestandthenoscillatesbelowandthenbackabove. Dw/Dtat the crest is subsequently shown to be perhaps the key indicator of the predictive capability of both the analytical and the CA theories. Again also, the Cnoidal Approximation predictions at N of 5 and 7 through were visually identical. The associated rms errors are listed in Table 3. Note that the rms errors are again rather larger than was the case for the Figure wave. This was expected as the Figure 5 wave is in much deeper water, stretching the credibility of the shallow water response implicit in the stream function representation (Eqs. 5 through 8). The wave height is also relatively extreme. Nevertheless, the errors remain respectably small. 6
17 η(x) [m] Cnoidal 5 Cnoidal Approx. 8 [u,w](x,η) [m/s] D[u,w]/Dt(X,η) [m/s ] (a) Water surface X [m] u(x,η) Analytical N=8 w(x,η) Analytical N= (b) Velocity X [m] (c) Acceleration X [m] Figure 5: Analytical and Cnoidal Approximation Predictions at N =8 for h= m, H=. m, T= s, U E =. The relationship in magnitudes between the analytical errors and the various CA errors is maintained. 7 Limits of Validity The limits of validity of the CA theory does not extend to the entire spectrum of length scales(water depth h, wave height H and wave length L). As previously outlined(equation 6 and discussion between Equations 6 and 7), solitary waves (L =, and m=) violate the CA problem formulation. In contrast, analytical theories for cnoidal waves may provide viable predictions at m=. Both analytical theories for cnoidal waves and the present CA theory experience difficulties on approach to the limit wave. It is apparent from Figures 3 and 5 that the CA theory can provide credible wave predictions for significantly higher waves than was possible with the fifth order analytical 7
18 .8 H/H Limit.6.4. CA Cnoidal ω h/g Cnoidal Stokes Figure 6: Comparative validity of analytical Cnoidal 5 theory and numerical CA theory. theory. The established (see Sobey, Figure 8) limits of validity for the analytical theory are reproduced in Figure 6, focussing on the range ω h/g.65 there suggested as appropriate for cnoidal wave theory. (Stokes-style wave theory is appropriate in deeper water.) The analytical theory seems to provide reasonable predictions up to wave heights increasingfromabout.5ofthelimitwaveinveryshallowwater(ω h/g )tomarginally above.7 of the limit wave height in transition water (ω h/g.65). The CA approach to the limit wave has been explored through a data base of solutions at depths h ranging from to 5 m at period T= s. Attention was specifically directed to the evolution with increasing wave height of the (a) Dimensionless wave length L/h A moderate increase in the domain aspect ratio L/h above the Airy (linear) wave theory prediction of L Airy h is expected as the wave height is increased. (b) Dimensionless crest elevation η Cr /H = π kh, where ω = gktanhkh,k = π/l Airy (54) η Cr = η(,) is expected to increase above H/ as H increases. At the limit wave, the crest is a stagnation point in the steady frame, so that η Cr increases toward R/g (Eq. ), which approaches closer to H as the depth decreases. (c) Dimensionless horizontal crest velocity u Cr /C u Cr = u(,) is expected to increase toward the phase speed C at the limit wave. This is a further consequence of the steady-frame stagnation point at the crest for the limit wave. 8
19 (d) Dimensionless vertical crest acceleration (Dw/Dt) Cr /g (Dw/Dt) Cr (Dw/Dt at X=,t=) is expected to decrease toward g/ at the limit wave (Longuet-Higgins & Fox 977). In each case, the progression with increasing H is expected to be smooth. Any departure from a smooth progression will identify a failure of the CA theory. But analytical continuity may result in smooth transitions to flawed predictions. Comparison with the existing fifth-order analytical theory will provide confirmation for small to moderately extreme wave heights, as suggested in Figure 6. Complementary support for moderately extreme to limit waves has been extracted from the Williams (985) tables. Direct use of these tabulated predictions requires interpolation (in h/gt and H/gT ) over a two-dimensional and irregular grid of tabulated predictions. Bi-cubic interpolation over the irregular grid was adopted, and some scatter in the predictions is expected. The Williams (985) predictions for the limit wave seem secure; interpolated values are used in the present definition of H Limit. But the transition from moderately extreme to the limit wave are rather less secure, being characterised (Williams 985, p. 6) as less than satisfactory. Of solution characteristics (a) through (d) listed above, predictions of L/h only are listed in this moderately extreme to the limit wave region. It is appropriate to note also that the Williams tables provide essentially a Stokes approximation, extended to very high order, about for deep-water waves and to 8 for shallow-water waves (Williams 985, p.6). It is not certain that the very high order in shallow water has not been impacted by limited machine precision. There is no discussion of this possibility. There is nonetheless evidence (minor profile oscillations) of declining applicability in shallow water in some of the interpolated predictions at depths approaching m. Figure 7 summarises the evolution for h= m at N=5. (Figure is a sample at H=.5 m from this sequence of solutions). Figure 7 parts (a) through (d) correspond to the listed items (a) through (d) identified for specific attention. The solid dots are the numerical CA 5 predictions, the dashed line is the analytical cnoidal 5 predictions and the solid line is the predictions interpolated from the Williams (985) tables. In each part figure, the wave height scale has been truncated at the limit wave, which is listed in the figure caption. The L/h predictions, part (a), correspond closely up to H.5 m, and the CA 5 and Cnoidal 5 predictions up to the limit wave. The η Cr /H predictions, part (b), show good agreement throughout. The CA 5 and Williams-interpolated predictions for u Cr /C, part (c), show good agreement up to H.5 m. Beyond this height, the CA 5 predictions remain smooth, as expected from analytical continuity. The Williams-interpolated predictions have a sudden trend change to u Cr /C= at the limit wave. There is clearly a rapid change expected in this region. The upper limit is secure and the lower limit is credible. As reported above, Williams table predictions in this region are not especially secure and only integral properties are listed. Without resolution of this rapid change, interpolated predictions become the sudden linear trends seen clearly in parts (c) and (d). The prediction uncertainty is clearly marked. Regardless, theca 5 prediction at the limit wave, u Cr /C.75, is not acceptable. The 9
20 Numerical, N=5 Analytical, 5th order Williams (985) (a) L/h η Cr /H (b) u /C (c) Cr (Dw/Dt) /g (d) Cr Figure 7: Solution Evolution with Wave Height at N=5 for h= m, T= s, U E =. H Limit =.59 m analytical Cnoidal 5 predictions separate at only moderate wave height, reaching u Cr /C = at H.35 m, well below the limit wave. These are unacceptable predictions, an observation strongly emphasised by part (d) where the analytical predictions are low at moderate wave heights and experience a rapid trend reversal toward zero vertical acceleration at H.35 m. This rapid trend reversal in the analytical predictions for (Dw/Dt) Cr is the clearest indication that the analytical theory has been extended beyond its region of applicability. The CA 5 and Williams-interpolated predictions closely correspond to H.5 m, beyond which the CA 5 predictions for (Dw/Dt) Cr experience a trend reversal similar to the analytical predictions. Once again, this trend reversal identifies the limit of applicability for the CA 5 predictions at h= m. The CA 8 predictions at the same depth, Figure 8, are very much more satisfactory. The response patterns in parts (a) through (d) are similar to the CA 5 predictions in Figure 7, except that the CA 8 predictions follow the Williams-interpolated predictions
21 Numerical, N=8 Analytical, 5th order Williams (985) (a) L/h η Cr /H (b) u /C (c) Cr (Dw/Dt) /g (d) Cr Figure 8: Solution Evolution with Wave Height at N=8 for h= m, T= s, U E =. H Limit =.59 m, H Valid =.38 m. now beyond H.35 m. Further increases in the truncation order N do not significantly impact this response. This was anticipated in the discussion related to Tables through 3, to the extent that order N=8 has been routinely adopted. It is clear from Figure 8(c) and (d) that the present CA formulation can not reach the limit wave. A smooth crest profile (Eq. 6) is assumed, which conflicts with the discontinuous crest with included angle π/3 expected at the limit wave. The upper limit of validity of the CA theory can be identified by the separation of the CA and Williams-interpolated predictions for u Cr and (Dw/Dt) Cr. The separation is amplified for (Dw/Dt) Cr. The upper limit of validity is identified as the wave height H Valid where H Valid is listed in the Figure 8 caption. Dw Dt CA 8 Cr Dw Dt Williams Cr =.5g (55)
22 3 3 Numerical, N=8 Analytical, 5th order Williams (985) (a) L/h η Cr /H (b) u /C (c) Cr (Dw/Dt) /g (d) Cr Figure 9: Solution Evolution with Wave Height at N=8 for h=5 m, T= s, U E =. H Limit =3.78 m, H Valid =3.3 m. Almost identical response patterns are repeated as the depth is increased, for example in Figures 9 and at depths of 5 and m respectively. Estimated values of H Valid, following the Eq. 55 definition, at depths from to m are included in Figure 6. CA 8 predictions, where appropriate (ω h/g.65), seem to be routinely valid up to about 88% of the limit wave height. The CA 8 theory extends to significantly higher wave heights than the analytical theory. There is no expectation that the present CA theory can extend closer to the limit wave. 8 Conclusions A Cnoidal Approximation (CA) wave theory for steady progressive waves in shallow water is described and explored. The formulation of the theory is analytical, building on existing
23 Numerical, N=8 Analytical, 5th order Williams (985) (a) L/h η Cr /H (b) u /C (c) Cr (Dw/Dt) /g (d) Cr Figure : Solution Evolution with Wave Height at N=8 for h= m, T= s, U E =. H Limit =.98 m, H Valid =.33 m. analytical theories for cnoidal waves. The solution is numerical, organised as a problem in nonlinear optimisation. The analytical formulation is based on the Lamb (93) series solution for the Laplace equation, which has horizontal and vertical scaling suitable for shallow water waves. The adopted solution for the stream function Ψ exactly satisfies the bottom boundary condition and the periodic lateral boundary condition. Much of the balance of the analytical formulation is classical, the kinematic free surface boundary condition, the dynamic free surface boundary condition, the definition of wave height, the mean water level constraint and the dispersion relationship. Imposition of the periodic lateral boundary condition specifically excludes solitary wave solutions. Truncation of the stream function series at order N introduces a small residual error in the field equation. This residual error is zero at the bottom and largest in magnitude at the free surface. It is accommodated through a free surface Laplace condition, along with 3
24 the traditional kinematic and dynamic free surface boundary conditions. Theanalyticalformulationiscompletedbyseriesexpansionsincn j (χ)forj=,,,...n for the function f(χ) in the stream function and for the water surface elevation η(χ). The stream function, velocity components and velocity gradients require first and second χ derivatives of cn j (χ), which are provided analytically by the definition of suitable transformation matrices. The balance of the solution is completed numerically. The problem formulation provides 3M +4 implicit and nonlinear algebraic equations in N +7 unknowns. The numerical solution is accomplished as a problem in nonlinear optimisation, based on the Eq. 48 least squares objective function. A trust region algorithm was adopted. Numerical solution issues such as variable scaling, initial solution estimation and convergence criteria are outlined in the text. The balance of the kinematics are available from predictive equations summarised in Appendix B. Confirmation of the CA-predicted kinematics is provided by comparison (Figure, Table ) with the analytical Cnoidal 5 theory, but only within the range of validity of the analytical theory. Errors in the CA theory have been characterised by the root-mean-square errors in the kinematic free surface boundary condition, the dynamic free surface boundary condition and the Laplace residual respectively. In all cases, the rms errors are very small. The optimum appears to be CA 8. Beyond N=8, there seems to be some increase in the rms error levels, presumably a consequence of the impact of finite machine precision on the convergence criteria in the nonlinear optimisation algorithm. The rms error levels at CA 8 are very acceptable, in comparison with solution unknowns that have been scaled to order one. Two further wave comparisons (Figures 3,Table in shallow water and Figures 5,Table 3 in transitional water), show moderately extreme waves beyond the validity range of the analytical Cnoidal 5 theory. In both cases, the CA 8 predictions seem appropriate. There is subsequent confirmation in Figures 8 and. Exploration of the CA theory concludes with an investigation of the limits of validity of the CA predictions. The predictions are compared (Figures 7 through ) with the analytical Cnoidal 5 theory and also predictions interpolated from the Williams tables, an extremely high order Stokes approximation. As expected, satisfactory response is demonstrated by the Cnoidal 5 theory only for small to moderate wave heights. The CA predictions extend the validity to higher waves, and the benefit of increasing the truncation order is clear. The upper wave hight limit of validity of the CA 8 theory is identified at significant departure of the CA 8 predictions from the William-interpolated predictions. This H Valid can not reach the limit wave H Limit, as the discontinuous crest of the limit wave is precluded by the CA theory. The estimates for H Valid are consolidated on Figure 6. The CA theory remains valid to about 88% of the limit wave height, throughout the shallow to transitional range (ω h/g.65) of applicability. 4
25 A Cnoidal Transformation Matrices () d cn j (χ)/dχ Analytical differentiation leads to powers and products of Jacobian sn(χ), cn(χ) and dn(χ) terms. These powers and products are transformed to sums of powers of cn (χ), using identities among these functions based on sn (χ) = cn (χ) and dn (χ) = m+mcn (χ) [Gradshteyn & Ryzhik (965, 8.54(4,5))]. The generic result is d dχ cnj (χ) = j(j )( m)cn j (χ)+4j (m )cn j (χ) j(j+)mcn j+ (χ) (56) The upper left corner of the equivalent transformation matrix is... m 8m 4 6m... m 3m 6 m... F = 3 3m 7m 36 4m m 8m 64 7m (57) () dcn j (χ)/dχ In a similar manner, d dχ cnj (χ) = jscd(χ)cn j (χ) (58) The equivalent transformation matrix is G = (59) 5
26 B Complete Kinematics Given a successful Cnoidal Approximation solution, the complete kinematics are available as: Ψ(X,z) = U(X,z) = h k= U X = α (X,z) h ( ) k(+ζ)k+ (k+)! k= ( ) k(+ζ)k (k)! f k (χ) η(x) = f k (χ) ( ) k(+ζ)k g k (χ) (k)! k= w X = α ( ) k(+ζ)k+ h (X,z) h k (χ) (k+)! k= Du Dt = U U (X,z) X +w U z B j cn j (χ;m) ([5,6]) j= w(x,z) = α h U z w z Dw Dt = (X,z) h k= ( ) k(+ζ)k+ (k+)! g k (χ) ([8,9]) ( ) k(+ζ)k (k )! f k(χ) k= (6,[3]) = U (X,z) X ([3,3]) (X,z) = U w (X,z) X +w w ([]) z p d (X,z) = ρr ρ(u +w ) (6) References Conn, A. R., Gould, N. I. M. & Toint, P. L. (), Trust-Region Methods, MPS/SIAM Series on Optimization, SIAM Society for Industrial& Applied Mathematics, Philadelphia, PA. Engevik, L. (3), A comment on the series solution of the solitary-wave problem, Zeitschrift für angewandte Mathematik und Physik 54, Fenton, J. D. (979), A high-order cnoidal wave theory, Journal of Fluid Mechanics 94, 9 6. Gradshteyn, I. S.& Ryzhik, I. M.(965), Table of Integrals, Series and Products, Academic Press, New York. Keller, J. B. (948), The solitary wave and periodic waves in shallow water, Communications on Pure and Applied Mathematics, Laitone, E. V. (96), The second approximation to cnoidal and solitary waves, Journal of Fluid Mechanics 9,
27 Lamb, H. (93), Hydrodynamics, 6 edn, Cambridge University Press, Cambridge. Longuet-Higgins, M. S. & Fox, M. J. H. (977), Theory of the almost-highest wave: the inner solution, Journal of Fluid Mechanics 8, Sobey, R. J. (989), Variations on Fourier wave theory, International Journal for Numerical Methods in Fluids 9, Sobey, R. J. (), Steep progressive waves in deep and shallow water, Engineering and Computational Mechanics. In Press; accepted May. Williams, J. M. (985), Tables of Progressive Gravity Waves, Pitman, Boston. 7
WavePiston Project. Structural Concept Development Hydrodynamic Aspects. Preliminary Analytical Estimates. February 2010
WavePiston Project Structural Concept Development Hydrodynamic Aspects Preliminary Analytical Estimates February 2010 WavePiston Project Structural Concept Development Hydrodynamic Aspects Preliminary
MODULE VII LARGE BODY WAVE DIFFRACTION
MODULE VII LARGE BODY WAVE DIFFRACTION 1.0 INTRODUCTION In the wave-structure interaction problems, it is classical to divide into two major classification: slender body interaction and large body interaction.
Differential Relations for Fluid Flow. Acceleration field of a fluid. The differential equation of mass conservation
Differential Relations for Fluid Flow In this approach, we apply our four basic conservation laws to an infinitesimally small control volume. The differential approach provides point by point details of
NUMERICAL ANALYSIS OF OPEN CHANNEL STEADY GRADUALLY VARIED FLOW USING THE SIMPLIFIED SAINT-VENANT EQUATIONS
TASK QUARTERLY 15 No 3 4, 317 328 NUMERICAL ANALYSIS OF OPEN CHANNEL STEADY GRADUALLY VARIED FLOW USING THE SIMPLIFIED SAINT-VENANT EQUATIONS WOJCIECH ARTICHOWICZ Department of Hydraulic Engineering, Faculty
INTRODUCTION TO FLUID MECHANICS
INTRODUCTION TO FLUID MECHANICS SIXTH EDITION ROBERT W. FOX Purdue University ALAN T. MCDONALD Purdue University PHILIP J. PRITCHARD Manhattan College JOHN WILEY & SONS, INC. CONTENTS CHAPTER 1 INTRODUCTION
Frequency-domain and stochastic model for an articulated wave power device
Frequency-domain stochastic model for an articulated wave power device J. Cândido P.A.P. Justino Department of Renewable Energies, Instituto Nacional de Engenharia, Tecnologia e Inovação Estrada do Paço
Dimensional analysis is a method for reducing the number and complexity of experimental variables that affect a given physical phenomena.
Dimensional Analysis and Similarity Dimensional analysis is very useful for planning, presentation, and interpretation of experimental data. As discussed previously, most practical fluid mechanics problems
CHAPTER 9 CHANNELS APPENDIX A. Hydraulic Design Equations for Open Channel Flow
CHAPTER 9 CHANNELS APPENDIX A Hydraulic Design Equations for Open Channel Flow SEPTEMBER 2009 CHAPTER 9 APPENDIX A Hydraulic Design Equations for Open Channel Flow Introduction The Equations presented
Chapter 2. Derivation of the Equations of Open Channel Flow. 2.1 General Considerations
Chapter 2. Derivation of the Equations of Open Channel Flow 2.1 General Considerations Of interest is water flowing in a channel with a free surface, which is usually referred to as open channel flow.
Solving Simultaneous Equations and Matrices
Solving Simultaneous Equations and Matrices The following represents a systematic investigation for the steps used to solve two simultaneous linear equations in two unknowns. The motivation for considering
Fluids and Solids: Fundamentals
Fluids and Solids: Fundamentals We normally recognize three states of matter: solid; liquid and gas. However, liquid and gas are both fluids: in contrast to solids they lack the ability to resist deformation.
State of Stress at Point
State of Stress at Point Einstein Notation The basic idea of Einstein notation is that a covector and a vector can form a scalar: This is typically written as an explicit sum: According to this convention,
ALL GROUND-WATER HYDROLOGY WORK IS MODELING. A Model is a representation of a system.
ALL GROUND-WATER HYDROLOGY WORK IS MODELING A Model is a representation of a system. Modeling begins when one formulates a concept of a hydrologic system, continues with application of, for example, Darcy's
Basic Equations, Boundary Conditions and Dimensionless Parameters
Chapter 2 Basic Equations, Boundary Conditions and Dimensionless Parameters In the foregoing chapter, many basic concepts related to the present investigation and the associated literature survey were
Simulation of Offshore Structures in Virtual Ocean Basin (VOB)
Simulation of Offshore Structures in Virtual Ocean Basin (VOB) Dr. Wei Bai 29/06/2015 Department of Civil & Environmental Engineering National University of Singapore Outline Methodology Generation of
Nonlinear Iterative Partial Least Squares Method
Numerical Methods for Determining Principal Component Analysis Abstract Factors Béchu, S., Richard-Plouet, M., Fernandez, V., Walton, J., and Fairley, N. (2016) Developments in numerical treatments for
Høgskolen i Narvik Sivilingeniørutdanningen STE6237 ELEMENTMETODER. Oppgaver
Høgskolen i Narvik Sivilingeniørutdanningen STE637 ELEMENTMETODER Oppgaver Klasse: 4.ID, 4.IT Ekstern Professor: Gregory A. Chechkin e-mail: [email protected] Narvik 6 PART I Task. Consider two-point
Open channel flow Basic principle
Open channel flow Basic principle INTRODUCTION Flow in rivers, irrigation canals, drainage ditches and aqueducts are some examples for open channel flow. These flows occur with a free surface and the pressure
High Speed Aerodynamics Prof. K. P. Sinhamahapatra Department of Aerospace Engineering Indian Institute of Technology, Kharagpur
High Speed Aerodynamics Prof. K. P. Sinhamahapatra Department of Aerospace Engineering Indian Institute of Technology, Kharagpur Module No. # 01 Lecture No. # 06 One-dimensional Gas Dynamics (Contd.) We
TWO-DIMENSIONAL FINITE ELEMENT ANALYSIS OF FORCED CONVECTION FLOW AND HEAT TRANSFER IN A LAMINAR CHANNEL FLOW
TWO-DIMENSIONAL FINITE ELEMENT ANALYSIS OF FORCED CONVECTION FLOW AND HEAT TRANSFER IN A LAMINAR CHANNEL FLOW Rajesh Khatri 1, 1 M.Tech Scholar, Department of Mechanical Engineering, S.A.T.I., vidisha
AP1 Oscillations. 1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false?
1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false? (A) The displacement is directly related to the acceleration. (B) The
Effect of Aspect Ratio on Laminar Natural Convection in Partially Heated Enclosure
Universal Journal of Mechanical Engineering (1): 8-33, 014 DOI: 10.13189/ujme.014.00104 http://www.hrpub.org Effect of Aspect Ratio on Laminar Natural Convection in Partially Heated Enclosure Alireza Falahat
Chapter 28 Fluid Dynamics
Chapter 28 Fluid Dynamics 28.1 Ideal Fluids... 1 28.2 Velocity Vector Field... 1 28.3 Mass Continuity Equation... 3 28.4 Bernoulli s Principle... 4 28.5 Worked Examples: Bernoulli s Equation... 7 Example
ATM 316: Dynamic Meteorology I Final Review, December 2014
ATM 316: Dynamic Meteorology I Final Review, December 2014 Scalars and Vectors Scalar: magnitude, without reference to coordinate system Vector: magnitude + direction, with reference to coordinate system
Appendix 4-C. Open Channel Theory
4-C-1 Appendix 4-C Open Channel Theory 4-C-2 Appendix 4.C - Table of Contents 4.C.1 Open Channel Flow Theory 4-C-3 4.C.2 Concepts 4-C-3 4.C.2.1 Specific Energy 4-C-3 4.C.2.2 Velocity Distribution Coefficient
Linköping University Electronic Press
Linköping University Electronic Press Report Well-posed boundary conditions for the shallow water equations Sarmad Ghader and Jan Nordström Series: LiTH-MAT-R, 0348-960, No. 4 Available at: Linköping University
Lecture L3 - Vectors, Matrices and Coordinate Transformations
S. Widnall 16.07 Dynamics Fall 2009 Lecture notes based on J. Peraire Version 2.0 Lecture L3 - Vectors, Matrices and Coordinate Transformations By using vectors and defining appropriate operations between
2.016 Hydrodynamics Prof. A.H. Techet Fall 2005
.016 Hydrodynamics Reading #7.016 Hydrodynamics Prof. A.H. Techet Fall 005 Free Surface Water Waves I. Problem setu 1. Free surface water wave roblem. In order to determine an exact equation for the roblem
Physics of the Atmosphere I
Physics of the Atmosphere I WS 2008/09 Ulrich Platt Institut f. Umweltphysik R. 424 [email protected] heidelberg.de Last week The conservation of mass implies the continuity equation:
Waves. Wave Parameters. Krauss Chapter Nine
Waves Krauss Chapter Nine Wave Parameters Wavelength = λ = Length between wave crests (or troughs) Wave Number = κ = 2π/λ (units of 1/length) Wave Period = T = Time it takes a wave crest to travel one
The Fourth International DERIVE-TI92/89 Conference Liverpool, U.K., 12-15 July 2000. Derive 5: The Easiest... Just Got Better!
The Fourth International DERIVE-TI9/89 Conference Liverpool, U.K., -5 July 000 Derive 5: The Easiest... Just Got Better! Michel Beaudin École de technologie supérieure 00, rue Notre-Dame Ouest Montréal
NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES
Vol. XX 2012 No. 4 28 34 J. ŠIMIČEK O. HUBOVÁ NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES Jozef ŠIMIČEK email: [email protected] Research field: Statics and Dynamics Fluids mechanics
What is the most obvious difference between pipe flow and open channel flow????????????? (in terms of flow conditions and energy situation)
OPEN CHANNEL FLOW 1 3 Question What is the most obvious difference between pipe flow and open channel flow????????????? (in terms of flow conditions and energy situation) Typical open channel shapes Figure
Mathematical Modeling and Engineering Problem Solving
Mathematical Modeling and Engineering Problem Solving Berlin Chen Department of Computer Science & Information Engineering National Taiwan Normal University Reference: 1. Applied Numerical Methods with
Introduction to COMSOL. The Navier-Stokes Equations
Flow Between Parallel Plates Modified from the COMSOL ChE Library module rev 10/13/08 Modified by Robert P. Hesketh, Chemical Engineering, Rowan University Fall 2008 Introduction to COMSOL The following
CEE 370 Fall 2015. Laboratory #3 Open Channel Flow
CEE 70 Fall 015 Laboratory # Open Channel Flow Objective: The objective of this experiment is to measure the flow of fluid through open channels using a V-notch weir and a hydraulic jump. Introduction:
Thompson/Ocean 420/Winter 2005 Tide Dynamics 1
Thompson/Ocean 420/Winter 2005 Tide Dynamics 1 Tide Dynamics Dynamic Theory of Tides. In the equilibrium theory of tides, we assumed that the shape of the sea surface was always in equilibrium with the
du u U 0 U dy y b 0 b
BASIC CONCEPTS/DEFINITIONS OF FLUID MECHANICS (by Marios M. Fyrillas) 1. Density (πυκνότητα) Symbol: 3 Units of measure: kg / m Equation: m ( m mass, V volume) V. Pressure (πίεση) Alternative definition:
Module 1 : Conduction. Lecture 5 : 1D conduction example problems. 2D conduction
Module 1 : Conduction Lecture 5 : 1D conduction example problems. 2D conduction Objectives In this class: An example of optimization for insulation thickness is solved. The 1D conduction is considered
Mean value theorem, Taylors Theorem, Maxima and Minima.
MA 001 Preparatory Mathematics I. Complex numbers as ordered pairs. Argand s diagram. Triangle inequality. De Moivre s Theorem. Algebra: Quadratic equations and express-ions. Permutations and Combinations.
CHAPTER 8 FACTOR EXTRACTION BY MATRIX FACTORING TECHNIQUES. From Exploratory Factor Analysis Ledyard R Tucker and Robert C.
CHAPTER 8 FACTOR EXTRACTION BY MATRIX FACTORING TECHNIQUES From Exploratory Factor Analysis Ledyard R Tucker and Robert C MacCallum 1997 180 CHAPTER 8 FACTOR EXTRACTION BY MATRIX FACTORING TECHNIQUES In
Statistical Analysis of Non-stationary Waves off the Savannah Coast, Georgia, USA
1 Statistical Analysis of Non-stationary Waves off the Savannah Coast, Xiufeng Yang School of Civil and Environmental Engineering, Georgia Institute of Technology, Atlanta, GA, USA, 30332 ([email protected])
Introduction to the Finite Element Method
Introduction to the Finite Element Method 09.06.2009 Outline Motivation Partial Differential Equations (PDEs) Finite Difference Method (FDM) Finite Element Method (FEM) References Motivation Figure: cross
Lecture L2 - Degrees of Freedom and Constraints, Rectilinear Motion
S. Widnall 6.07 Dynamics Fall 009 Version.0 Lecture L - Degrees of Freedom and Constraints, Rectilinear Motion Degrees of Freedom Degrees of freedom refers to the number of independent spatial coordinates
Introduction to Engineering System Dynamics
CHAPTER 0 Introduction to Engineering System Dynamics 0.1 INTRODUCTION The objective of an engineering analysis of a dynamic system is prediction of its behaviour or performance. Real dynamic systems are
Numerical Wave Generation In OpenFOAM R
Numerical Wave Generation In OpenFOAM R Master of Science Thesis MOSTAFA AMINI AFSHAR Department of Shipping and Marine Technology CHALMERS UNIVERSITY OF TECHNOLOGY Göteborg, Sweden, 2010 Report No. X-10/252
Chapter 6: Solving Large Systems of Linear Equations
! Revised December 8, 2015 12:51 PM! 1 Chapter 6: Solving Large Systems of Linear Equations Copyright 2015, David A. Randall 6.1! Introduction Systems of linear equations frequently arise in atmospheric
Chapter 8: Flow in Pipes
Objectives 1. Have a deeper understanding of laminar and turbulent flow in pipes and the analysis of fully developed flow 2. Calculate the major and minor losses associated with pipe flow in piping networks
Analysis of Bayesian Dynamic Linear Models
Analysis of Bayesian Dynamic Linear Models Emily M. Casleton December 17, 2010 1 Introduction The main purpose of this project is to explore the Bayesian analysis of Dynamic Linear Models (DLMs). The main
Distinguished Professor George Washington University. Graw Hill
Mechanics of Fluids Fourth Edition Irving H. Shames Distinguished Professor George Washington University Graw Hill Boston Burr Ridge, IL Dubuque, IA Madison, Wl New York San Francisco St. Louis Bangkok
Numerical methods for American options
Lecture 9 Numerical methods for American options Lecture Notes by Andrzej Palczewski Computational Finance p. 1 American options The holder of an American option has the right to exercise it at any moment
Numerical Analysis An Introduction
Walter Gautschi Numerical Analysis An Introduction 1997 Birkhauser Boston Basel Berlin CONTENTS PREFACE xi CHAPTER 0. PROLOGUE 1 0.1. Overview 1 0.2. Numerical analysis software 3 0.3. Textbooks and monographs
CITY UNIVERSITY LONDON. BEng Degree in Computer Systems Engineering Part II BSc Degree in Computer Systems Engineering Part III PART 2 EXAMINATION
No: CITY UNIVERSITY LONDON BEng Degree in Computer Systems Engineering Part II BSc Degree in Computer Systems Engineering Part III PART 2 EXAMINATION ENGINEERING MATHEMATICS 2 (resit) EX2005 Date: August
Introduction to the Finite Element Method (FEM)
Introduction to the Finite Element Method (FEM) ecture First and Second Order One Dimensional Shape Functions Dr. J. Dean Discretisation Consider the temperature distribution along the one-dimensional
APPLIED MATHEMATICS ADVANCED LEVEL
APPLIED MATHEMATICS ADVANCED LEVEL INTRODUCTION This syllabus serves to examine candidates knowledge and skills in introductory mathematical and statistical methods, and their applications. For applications
Ravi Kumar Singh*, K. B. Sahu**, Thakur Debasis Mishra***
Ravi Kumar Singh, K. B. Sahu, Thakur Debasis Mishra / International Journal of Engineering Research and Applications (IJERA) ISSN: 48-96 www.ijera.com Vol. 3, Issue 3, May-Jun 3, pp.766-77 Analysis of
1 The basic equations of fluid dynamics
1 The basic equations of fluid dynamics The main task in fluid dynamics is to find the velocity field describing the flow in a given domain. To do this, one uses the basic equations of fluid flow, which
N 1. (q k+1 q k ) 2 + α 3. k=0
Teoretisk Fysik Hand-in problem B, SI1142, Spring 2010 In 1955 Fermi, Pasta and Ulam 1 numerically studied a simple model for a one dimensional chain of non-linear oscillators to see how the energy distribution
How High a Degree is High Enough for High Order Finite Elements?
This space is reserved for the Procedia header, do not use it How High a Degree is High Enough for High Order Finite Elements? William F. National Institute of Standards and Technology, Gaithersburg, Maryland,
Calculating resistance to flow in open channels
Alternative Hydraulics Paper 2, 5 April 2010 Calculating resistance to flow in open channels http://johndfenton.com/alternative-hydraulics.html [email protected] Abstract The Darcy-Weisbach formulation
- momentum conservation equation ρ = ρf. These are equivalent to four scalar equations with four unknowns: - pressure p - velocity components
J. Szantyr Lecture No. 14 The closed system of equations of the fluid mechanics The above presented equations form the closed system of the fluid mechanics equations, which may be employed for description
Numerical Methods for Engineers
Steven C. Chapra Berger Chair in Computing and Engineering Tufts University RaymondP. Canale Professor Emeritus of Civil Engineering University of Michigan Numerical Methods for Engineers With Software
. Address the following issues in your solution:
CM 3110 COMSOL INSTRUCTIONS Faith Morrison and Maria Tafur Department of Chemical Engineering Michigan Technological University, Houghton, MI USA 22 November 2012 Zhichao Wang edits 21 November 2013 revised
HIGH ORDER WENO SCHEMES ON UNSTRUCTURED TETRAHEDRAL MESHES
European Conference on Computational Fluid Dynamics ECCOMAS CFD 26 P. Wesseling, E. Oñate and J. Périaux (Eds) c TU Delft, The Netherlands, 26 HIGH ORDER WENO SCHEMES ON UNSTRUCTURED TETRAHEDRAL MESHES
Journal of Engineering Science and Technology Review 2 (1) (2009) 76-81. Lecture Note
Journal of Engineering Science and Technology Review 2 (1) (2009) 76-81 Lecture Note JOURNAL OF Engineering Science and Technology Review www.jestr.org Time of flight and range of the motion of a projectile
For example, estimate the population of the United States as 3 times 10⁸ and the
CCSS: Mathematics The Number System CCSS: Grade 8 8.NS.A. Know that there are numbers that are not rational, and approximate them by rational numbers. 8.NS.A.1. Understand informally that every number
3 The boundary layer equations
3 The boundar laer equations Having introduced the concept of the boundar laer (BL), we now turn to the task of deriving the equations that govern the flow inside it. We focus throughout on the case of
FINITE ELEMENT : MATRIX FORMULATION. Georges Cailletaud Ecole des Mines de Paris, Centre des Matériaux UMR CNRS 7633
FINITE ELEMENT : MATRIX FORMULATION Georges Cailletaud Ecole des Mines de Paris, Centre des Matériaux UMR CNRS 76 FINITE ELEMENT : MATRIX FORMULATION Discrete vs continuous Element type Polynomial approximation
MATHEMATICAL METHODS OF STATISTICS
MATHEMATICAL METHODS OF STATISTICS By HARALD CRAMER TROFESSOK IN THE UNIVERSITY OF STOCKHOLM Princeton PRINCETON UNIVERSITY PRESS 1946 TABLE OF CONTENTS. First Part. MATHEMATICAL INTRODUCTION. CHAPTERS
NUMERICAL SIMULATION OF REGULAR WAVES RUN-UP OVER SLOPPING BEACH BY OPEN FOAM
NUMERICAL SIMULATION OF REGULAR WAVES RUN-UP OVER SLOPPING BEACH BY OPEN FOAM Parviz Ghadimi 1*, Mohammad Ghandali 2, Mohammad Reza Ahmadi Balootaki 3 1*, 2, 3 Department of Marine Technology, Amirkabir
Derive 5: The Easiest... Just Got Better!
Liverpool John Moores University, 1-15 July 000 Derive 5: The Easiest... Just Got Better! Michel Beaudin École de Technologie Supérieure, Canada Email; [email protected] 1. Introduction Engineering
4.3 Results... 27 4.3.1 Drained Conditions... 27 4.3.2 Undrained Conditions... 28 4.4 References... 30 4.5 Data Files... 30 5 Undrained Analysis of
Table of Contents 1 One Dimensional Compression of a Finite Layer... 3 1.1 Problem Description... 3 1.1.1 Uniform Mesh... 3 1.1.2 Graded Mesh... 5 1.2 Analytical Solution... 6 1.3 Results... 6 1.3.1 Uniform
The Quantum Harmonic Oscillator Stephen Webb
The Quantum Harmonic Oscillator Stephen Webb The Importance of the Harmonic Oscillator The quantum harmonic oscillator holds a unique importance in quantum mechanics, as it is both one of the few problems
Elasticity Theory Basics
G22.3033-002: Topics in Computer Graphics: Lecture #7 Geometric Modeling New York University Elasticity Theory Basics Lecture #7: 20 October 2003 Lecturer: Denis Zorin Scribe: Adrian Secord, Yotam Gingold
The Fourier Analysis Tool in Microsoft Excel
The Fourier Analysis Tool in Microsoft Excel Douglas A. Kerr Issue March 4, 2009 ABSTRACT AD ITRODUCTIO The spreadsheet application Microsoft Excel includes a tool that will calculate the discrete Fourier
CBE 6333, R. Levicky 1 Differential Balance Equations
CBE 6333, R. Levicky 1 Differential Balance Equations We have previously derived integral balances for mass, momentum, and energy for a control volume. The control volume was assumed to be some large object,
Introduction to CFD Basics
Introduction to CFD Basics Rajesh Bhaskaran Lance Collins This is a quick-and-dirty introduction to the basic concepts underlying CFD. The concepts are illustrated by applying them to simple 1D model problems.
Method of Green s Functions
Method of Green s Functions 8.303 Linear Partial ifferential Equations Matthew J. Hancock Fall 006 We introduce another powerful method of solving PEs. First, we need to consider some preliminary definitions
Paper Pulp Dewatering
Paper Pulp Dewatering Dr. Stefan Rief [email protected] Flow and Transport in Industrial Porous Media November 12-16, 2007 Utrecht University Overview Introduction and Motivation Derivation
Mesh Moving Techniques for Fluid-Structure Interactions With Large Displacements
K. Stein Department of Physics, Bethel College, St. Paul, MN 55112 T. Tezduyar Mechanical Engineering, Rice University, MS 321, Houston, TX 77005 R. Benney Natick Soldier Center, Natick, MA 01760 Mesh
2.0 BASIC CONCEPTS OF OPEN CHANNEL FLOW MEASUREMENT
2.0 BASIC CONCEPTS OF OPEN CHANNEL FLOW MEASUREMENT Open channel flow is defined as flow in any channel where the liquid flows with a free surface. Open channel flow is not under pressure; gravity is the
ME6130 An introduction to CFD 1-1
ME6130 An introduction to CFD 1-1 What is CFD? Computational fluid dynamics (CFD) is the science of predicting fluid flow, heat and mass transfer, chemical reactions, and related phenomena by solving numerically
Viscous flow through pipes of various cross-sections
IOP PUBLISHING Eur. J. Phys. 28 (2007 521 527 EUROPEAN JOURNAL OF PHYSICS doi:10.1088/0143-0807/28/3/014 Viscous flow through pipes of various cross-sections John Lekner School of Chemical and Physical
Which physics for full-wavefield seismic inversion?
Which physics for full-wavefield seismic inversion? M. Warner* (Imperial College London), J. Morgan (Imperial College London), A. Umpleby (Imperial College London), I. Stekl (Imperial College London) &
Dynamics. Basilio Bona. DAUIN-Politecnico di Torino. Basilio Bona (DAUIN-Politecnico di Torino) Dynamics 2009 1 / 30
Dynamics Basilio Bona DAUIN-Politecnico di Torino 2009 Basilio Bona (DAUIN-Politecnico di Torino) Dynamics 2009 1 / 30 Dynamics - Introduction In order to determine the dynamics of a manipulator, it is
SOLID MECHANICS TUTORIAL MECHANISMS KINEMATICS - VELOCITY AND ACCELERATION DIAGRAMS
SOLID MECHANICS TUTORIAL MECHANISMS KINEMATICS - VELOCITY AND ACCELERATION DIAGRAMS This work covers elements of the syllabus for the Engineering Council exams C105 Mechanical and Structural Engineering
Second Order Linear Partial Differential Equations. Part I
Second Order Linear Partial Differential Equations Part I Second linear partial differential equations; Separation of Variables; - point boundary value problems; Eigenvalues and Eigenfunctions Introduction
Scalars, Vectors and Tensors
Scalars, Vectors and Tensors A scalar is a physical quantity that it represented by a dimensional number at a particular point in space and time. Examples are hydrostatic pressure and temperature. A vector
Hydraulic losses in pipes
Hydraulic losses in pipes Henryk Kudela Contents 1 Viscous flows in pipes 1 1.1 Moody Chart.................................... 2 1.2 Types of Fluid Flow Problems........................... 5 1.3 Minor
Stability of Evaporating Polymer Films. For: Dr. Roger Bonnecaze Surface Phenomena (ChE 385M)
Stability of Evaporating Polymer Films For: Dr. Roger Bonnecaze Surface Phenomena (ChE 385M) Submitted by: Ted Moore 4 May 2000 Motivation This problem was selected because the writer observed a dependence
2x + y = 3. Since the second equation is precisely the same as the first equation, it is enough to find x and y satisfying the system
1. Systems of linear equations We are interested in the solutions to systems of linear equations. A linear equation is of the form 3x 5y + 2z + w = 3. The key thing is that we don t multiply the variables
Model Virginia Map Accuracy Standards Guideline
Commonwealth of Virginia Model Virginia Map Accuracy Standards Guideline Virginia Information Technologies Agency (VITA) Publication Version Control Publication Version Control: It is the user's responsibility
AN INTRODUCTION TO NUMERICAL METHODS AND ANALYSIS
AN INTRODUCTION TO NUMERICAL METHODS AND ANALYSIS Revised Edition James Epperson Mathematical Reviews BICENTENNIAL 0, 1 8 0 7 z ewiley wu 2007 r71 BICENTENNIAL WILEY-INTERSCIENCE A John Wiley & Sons, Inc.,
1. Fluids Mechanics and Fluid Properties. 1.1 Objectives of this section. 1.2 Fluids
1. Fluids Mechanics and Fluid Properties What is fluid mechanics? As its name suggests it is the branch of applied mechanics concerned with the statics and dynamics of fluids - both liquids and gases.
Lecture 3. Turbulent fluxes and TKE budgets (Garratt, Ch 2)
Lecture 3. Turbulent fluxes and TKE budgets (Garratt, Ch 2) In this lecture How does turbulence affect the ensemble-mean equations of fluid motion/transport? Force balance in a quasi-steady turbulent boundary
