Technical Data. wedi Shower Accessories

Transcription

1 Technical Data Shower Accessories

2 Technical Data Shower Accessories Overview A secret among bath design professionals is to use L- and U-shaped Building Panels to create more tileable surfaces in bathroom. To accommodate this popular trend, prefabricates many products and provides solutions for on-site customization of shapes and styles. Not only can you waterproof your tile substrates, but you can eliminate wooden framework by installing prefabricated design s tailored to fit your special needs. Prefabricated Elements include shower seats and benches, niches, curbs and ramps. Product Features Lightweight, easy to handle, cut & install Waterproof as tested and demonstrated according to ANSI A Mold/Mildew proof Thermally insulating Great for tile bonding using any cement or epoxy based thinset mortar Dimensionally stable, inert, does not deteriorate Contains no fibers or paper layers; and will not delaminate or fuel flames in fire emergencies Replace traditional cement boards and waterproof membranes in wet areas such as showers and steam showers Provides a perfect surface for tiling Prefabricated Shower Seats and Benches Create perfect waterproof seating solution for your shower. Shower Seats and Benches install much quicker and easier than metal tray or concrete seats. Plus, y are 100% waterproof due to CFC-free extruded polystyrene closed cell foam core. Full Foam Triangular Corner Seat The Full Foam Triangular Corner Seat is a fully prefabricated corner seat is 100% waterproof throughout. Unlike or systems, such as those made with non-waterproof white expanded polystyrene (EPS), Full Foam Triangular Corner Seat does not need to be treated with a waterproof membrane anymore. In addition, top surface is slightly sloped at a rate of 1/8 / ft. to allow water to run off toward floor drain. The seat can be cut to virtually any size. Where cut and blue foam is exposed, adhere, for example, an 1/8 thick panel piece to this area to recreate a perfect surface to bond tile to. This corner seat can be used in systems, conventional shower systems or even over older, existing tiles in an existing shower. The core of seat is made of extruded polystyrene foam and is coated with a rigid, sanded epoxy-based coating to accommodate for heavy duty commercial use. 2

3 Technical Data: Shower Accessories Installation of Full Foam Triangular Corner Seat 1 Dry fit seat into squared backerboard corner of your shower. Make sure it will firmly attach to two walls leaving no hollow areas between. 2 Mark seat s contact area so you know which area need to be covered with a 3/8 thinset application. 3 Apply modified thinset to both wall areas and floor area seat will touch using a 3/8 x 3/8 notch trowel. Apply more thinset in sloped shower floor area to fill voids. 4 Firmly attach seat into thinset bed and hold in position tightly using weights (tile boxes or similar leaning against seat leaning against seat until thinset can keep seat in it s position) 5 Apply a 1/2 bead of 6 Joint Sealant to all wallseat seams. The sealant will provide a waterproof and flexible seal. On bottom seam, fill gap between seat nottom and shower base slope with thinset and apply alkali resistant Mesh Tape 7 Spread Joint 8 Sealant flat over seam using a Corner Putty Knife. Cover 3/4 of eir side of seam with sealant. Your seat is ready to tile immediately once Joint Sealant is tack free. 3

4 Technical Data: Shower Accessories Assembly Instructions Assembly Instructions Floating Corner Seat corner seats not only install quicker and easier than any metal tray or concrete seat, but y are also totally unaffected by water due to ir closed cell foam base. The polyurethanebased mounting brackets allow for flexible installation and make sure that tiled seat can carry up to 300 lbs. of weight. No adddtional blocking is needed and product can even be installed against an existing tiled corner if needed. Corner Seats M, M, L L Corner Seats M, M, L L Installation Corner of Seat Seat MM Corner Seats Medium and Large x 17 x 17 (wall (wall sides), sides), thickness 4 4 (Item# (Item# ) Corner Seat Seat MM x 17 x Corner 17 (wall (wall Seat sides), Seat sides), L Lthickness 4 4 (Item# (Item# ) Corner Seat M x 24 x 24 (wall (wall sides), sides), thickness 4 4 (Item# (Item# ) Corner Seat Seat L L 17 x 17 (wall sides), thickness 4 (item # ) x 24 x 24 (wall (wall sides), sides), thickness 4 4 (Item# (Item# ) Seat Corner Seat L Seat assembly set set consists of: of: Seat 24 Seat x Seat 24 (wall sides), thickness Seat assembly set set (2) (2) 4 consists mounting (item # ) of: of: brackets (6) Seat (6) Seat fasteners Seat assembly consists (2) of: (2) mounting meshtape brackets tube (6) Seat tube (6) of fasteners of Element joint joint sealant sealant (2) mounting meshtape brackets tube (6) tube of Fasteners of joint joint sealant meshtape Installation: tube of joint sealant Installation: Apply Apply joint joint sealant on on mounting Apply Joint Sealant 1. to side of mounting bracket that 1. brackets will Apply side side be attached to joint that that joint will will sealant be be attached Building on on Panel to to wall. mounting brackets wall. wall. side side that that will will be be attached to to wall. wall Evenly Evenly distribute joint joint sealant with with a a notched Evenly trowel distribute until until until whole contact area joint is joint whole whole covered. sealant contact with with a a area area notched is is covered. trowel until until whole contact area area is is covered. Evenly distribute Joint Sealant with a notched trowel 3 Using a level, make sure you can achieve a slight pitch (1/ Use over Use a 1 level a ft.). level to to make make sure sure you you can can achieve a a slight slight Use Use a pitch pitch level a level (1/8 (1/8 to to make make over over sure 1 sure ft). 1 ft). you you can can achieve a a slight slight pitch pitch (1/8 (1/8 over over 1 ft). 1 ft). 4 Mount brackets through Building Panel wall into Mount solid 2 x 4 brackets wooden framework. through wall wall panels Mount into into brackets solid solid 2 2 through x 4 x 4 wooden framework. wall wall panels into into solid solid 2 2 x 4 x 4 wooden framework. 4

5 Technical Data: Shower Accessories 5. 5.Apply sealant to to blue foam 6. 6.Press seat into position andand Apply joint joint sealant blue foam Press seat into position of of seat that willwill contact apply a weight (i.e.tile box) so so that 5 edges 6 edges seat that contact wall apply a weight (i.e.tile box) that wall sealant can set under bond pressure. or or brackets using a notched trowel. sealant can set under bond pressure. brackets using a notched trowel. Using a notched trowel, apply Joint Sealant to blue Press seat into position and apply a weight (i.e., Apply joint to blue foam 6. tile 6. Press seat position and Apply joint sealant to blue foam Press seat position foam edges of seat that willsealant contact Building box) so that sealant caninto setinto under bondand pressure. Paneledges wall or of brackets. edges of contact apply a weight (i.e.tile so that wallwall seatseat thatthat willwill contact apply a weight (i.e.tile box)box) so that sealant under bond pressure. or brackets using a notched trowel. or brackets using a notched trowel. sealant cancan set set under bond pressure. 7 Apply Meshtape to tape transition joint between 7. 7.Apply andand tape Apply meshtape meshtape tape seat and Building Panel wall. Apply a flat transition joint between seat and transition joint seatfully thinset mortar bed over between Meshtape and embed it.and Apply a flat thinset mortar bedbed wall. wall. Apply a flat thinset mortar over meshtape andand fully embed it. it. over meshtape fully embed Apply meshtape and tape Apply meshtape and tape transition joint between transition joint between seatseat andand wall. Apply a flat thinset mortar wall. Apply a flat thinset mortar bedbed Straight Bench meshtape embed overover meshtape andand fullyfully embed it. it. This 100% waterproof bench is a prefabricated sampling of what can often be installed onsite and in custom dimensions, using our 2 building panels, which provide structural strength needed for seats and benches. Its hollow inside allows for additional installation space for plumbing and electric parts in steam showers and large spa function showers. It is sloped on top surface area at a rate of 1/8 / ft. to make sure water can run off to floor drain. 8 Step 7 now tohappens underside of seat. Apply 8. Apply same step now on on 8.TheThe same step happens now Meshtape and thinset mortar to vertical seams as well. underside of of seat where it isit is underside seat where connected to wall using mesh tape andand connected to wall using mesh tape thinset mortar. TheThe short vertical seams areare thinset mortar. short vertical seams The same step happens now The same step happens now on on taped with mesh and thinset mortar as well. taped with mesh thinset mortar asit well. underside of seat where is underside of seatand where it is connected to using mesh tape connected to wallwall using mesh tape andand thinset mortar. short vertical seams thinset mortar. TheThe short vertical seams are are taped with mesh thinset mortar as well. taped with mesh andand thinset mortar as well. Corporation Corporation Elk Grove Village, IL Landmeier Road, Suite Landmeier Road, Suite 200 Elk Grove Village, IL Fax Tel.Tel WEDI (9334) Fax WEDI (9334) info@corp.com info@corp.com Corporation Corporation Elk Grove Elk Grove Village, IL Landmeier Road, 1100 Landmeier Road, SuiteSuite Village, IL Fax. Fax WEDI (9334) Tel. Tel WEDI (9334) info@corp.com info@corp.com 5

6 Technical Data: Shower Accessories Prefabricated Niches Prefabricated Niches are fabricated from ½ Building Panels and come in three different size options. The perfect fit for all your shower necessities, our niches install quickly and safely, and integrate flush into wall panel assembly with fasteners x 8 Rectangular Niche Cut out a space of existing ½ wall panel 16 x 8 so that niche flanges can rest on 2 x 4 studs (16 o.c.) on both sides and line up flush with surrounding backerboard or drywall panels. 2 Insert niche into opening. Apply a bead of joint sealant along outside seam and smooth out with a putty knife to cover and waterproof seam. Apply a bead of joint sealant onto exposed stud, as well as along inside edges of wall panel x 12 Rectangular Niche Cut out a space of existing ½ wall panel 16 x 12 so that niche flanges can rest on 2 x 4 studs (16 o.c.) on both sides and line up flush with surrounding backerboard or drywall panels. 2 Insert niche into opening. Apply a bead of joint sealant along outside seam and smooth out with a putty knife to cover and waterproof seam. Apply a bead of joint sealant onto exposed stud, as well as along inside edges of wall panel x 16 Square Niche Cut out a space of existing ½ wall panel 16 x 16 so that niche flanges can rest on 2 x 4 studs (16 o.c.) on both sides and line up flush with surrounding backerboard or drywall panels. 2 Insert niche into opening. Apply a bead of joint sealant along outside seam and smooth out with a putty knife to cover and waterproof seam. Apply a bead of joint sealant onto exposed stud, as well as along inside edges of wall panel. 6

7 Technical Data: Shower Accessories 16 x 22 Rectangular Niche 1 Cut out a space of existing ½ wall panel 16 x 22 so that niche flanges can rest on 2 x 4 studs (16 o.c.) on both sides and line up flush with surrounding backerboard or drywall panels. Apply a bead of joint sealant onto exposed stud, as well as along inside edges of wall panel. 2 Insert niche into opening. Apply a bead of joint sealant along outside seam and smooth out with a putty knife to cover and waterproof seam. 16 x 42 Lean Combo Niche 1 Cut out a space of existing ½ wall panel 16 x 42 so that niche flanges can rest on 2 x 4 studs (16 o.c.) on both sides and line up flush with surrounding backerboard or drywall panels. Apply a bead of joint sealant onto exposed stud, as well as along inside edges of wall panel. 2 Insert niche into opening. Apply a bead of joint sealant along outside seam and smooth out with a putty knife to cover and waterproof seam. 7

8 Technical Data: Shower Accessories National Building Code Compliances Compliance with current ICC Evaluation Service standards ICC-ES PMG Listing PMG-1189 Effective Date: May 1, 2013 This listing is subject to re-examination in one year. (800) (562) A Subsidiary of International Code Council CSI: DIVISION: PLUMBING Section: Plumbing Fixtures (Shower System Kit) Product certification system: The ICC-ES product certification system includes testing samples taken from market or supplier s stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of supplier s quality system. Product: Listee: Fundo Shower System and Tile Backer Board Underlayments Corporation 1100 Landmeier Rd. Suite 200 Elk Grove Village, Illinois Compliance with following codes: Find Current Report on and 2009 International Plumbing Code (IPC) 2012 and 2009 International Residential Code (IRC) 2012 and 2009 Uniform Plumbing Code (UPC)* *Uniform Plumbing Code is a copyrighted publication if International Association of Plumbing and Mechanical Officials Compliance with following standard: Identification: Installation: Models: ANSI A , Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations a ICC-ES EG 159, Evaluation Guideline for Composite Backer Board ICC-ES AC 71, Acceptance Criteria for Foam Plastic Sheathing Panels Used as Water Resistive Barriersrs IAPMO PS ,, Field-Fabricated at ed Tiling ing Kits Packaging aging label for each system shall include manufacturer s name or trademark as well as ICC-ES PMG certification io mark. The Fundo Shower Systems s shall be installed in accordance a cordance with manufacturer s published instructions and applicable plicable code(s). Shower system components shall be assembled and can be customized in field. All shower bases and panels can be cut to size with hand saws or skill saws. Round curvy cuts can be made with a hand saw or jig saw. When provided drains must comply with ASME A as applicable. The pre-sloped, ready-to-tile shower bases may be used in lieu of an ANSI Z plastic shower receptors or any liner based shower installations. The drain units do not require weep holes. The Fundo shower bases are pre-sloped, ready-to-tile floor units. The building panels are engineered as a general purpose backer board and underlayment for tile and consist of a rigid extruded polystyrene foam covered on both sides with a cement-based resin surface and reinforcing mesh for durability and bonding with any type of thinset mortar. The systems linear drain is integrated and factory sealed into floor base. System assembly and components were proven to be waterproof and mold resistant when tested in accordance with A Shower system may include following components: shower base, building panels, curbs, niches, seats, benches, ramps, vapor barrier, fasteners, cover plates, sealants and drain. The Fundo family line includes following: Primo, Riolito, Riofino, Discreto, and ECOBATH. Conditions of Listing: 1. The Fundo Shower Systems shall be installed in accordance with manufacturer s published instructions and applicable code(s). 2. The Fundo Shower Systems are manufactured by GmbH, in Emsdetten, Germany under a quality control program with annual surveillance inspections by ICC-ES. Listings are not to be construed as representing aestics or any or attributes not specifically addressed, nor are y to be construed as an endorsement of subject of listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or or matter in this listing, or as to any product covered by listing. Copyright 2013 Page 1 of 1 8

9 Technical Data: Shower Accessories Prefabricated Curbs and Ramps Available in several options for shower entry designs where transitions are required, curbs and ramps can be installed with Fundo shower bases, as well as conventional mortar bed systems. Waterproof and versatile, Curbs and Ramps may be tiled before any glass doors, panels or glass block is installed and can carry weight of up to 480 lbs./ft. Epoxy glue is recommended instead of screw fasteners when installing shower door tracks. Full Foam Curbs Curb Over Shower Ramp Full Foam Curbs combine it all in one when compared to traditional methods of 2 x 4 wood assembly, lath, mud and waterproofing. They come presloped so water runs back into shower. Installation instructions can also be found in Fundo Primo Installation video ( com) Curb Overs are designed to water-proof over existing 2 x 4 wood constructions. A conventional PVC pan liner is sandwiched inside between 2 x 4 and Curb Over. The Curb Over will provide additional water-proofing and square corners for a perfect tile job. No fasteners should penetrate curb except on vertical outside of shower. Attach with thinset mortar only. Please install curb over in accordance with TCNA Handbook detail. Installation instructions can also be found in Curb Over Installation video ( The Shower Ramp is used to create curbless showers without recessing shower base into subfloor. The ramp provides a 1 slope over a 12 length and meets ADA requirements. The ramp should not be tiled with tiles smaller than 4 x 4 when wheelchairs are used in this shower. Installation instructions can also be found in Fundo Primo Installation video ( com) 9

10 Technical Data: Shower Accessories General Limitations In commercial applications, adequate fire barrier substrates may need to be installed behind foam products. Follow local and national building codes in all applications. Storage Store flat and keep dry with no exposure to s. Keep away from solvents and direct UV exposure. Disposal Product can be disposed with attached construction material/waste. Product will not negatively impact ground water. Product cannot decompose. Warranty Log onto to learn more about s warranty. MasterFormat 2004 Sections Section 07100: Damp-proofing & Waterproofing Section 09260: Gypsum Board Assemblies Section 09252: Cementitious backer board Section 09300: Tile 10

11 Technical Data: Shower Accessories Product Order Information Shower Seat M&L Description Width x Length x Height Unit Item # Seat M 17 x 17 (wall sides) x 4 1 pc /300 Seat L 5 x 8 x 4 1/2 1 pc /400 Bench Rectangular and Full Foam Triangle Seats Description Width x Length x Height Unit Item # Bench 16 x 32 x 20, sloped 1 pc /100 Corner Seat 23 x 23 (wall sides) x 20 1 pc /101 Rectangular ft bench made with 2 Building Panel, full; foam seat made of solid XPS foam. These units are pre-made and ready for thinset installation against walls and feature and 1/8 slope to front. Niche Square Edges Description Dimensions Unit Item # Niche Square Edges 16 x 8 1 pc /200 Niche Square Edges 16 x 12 1 pc / x 16 Niche Square Edges 16 x 16 1 pc /300 Niche Square Edges 16 x 22 incl. removable shelf 1 pc /400 Lean Combo Niche 16 x 42 incl. 2 removable shelves 1 pc /350 Installation ft over 2 x 4 s construction, 16 o.c. framework 16 x x 42 Important ft information ft Please noteft Scope of delivery ft Options ft Tileable surfaces 11

12 Technical Data: Shower Accessories Curb Over Description Width x Length x Height Unit Item # Curb Over Square Edges 5 x 5 x 4 1/2 1 pc /000 Curb Over Square Edges 5 x 8 x 4 1/2 1 pc /000 Installation over 2 x 4 construction. No fasteners should penetrate curb, except on vertical outside of shower. ft Full Foam Curb Description Width x Length x Height Unit Item # Curb Full Foam Square Edges 5 x 5 x 4 1/2 1 pc /002 Curb Full Foam Square Edges 5 x 8 x 4 1/2 1 pc /001 Sloped fton top surface Shower Ramps Description Width x Length x Height Unit Item # Shower Ramp* 12 x 5, sloped 1 1/2 to 1/4 1 pc /517 Shower Ramp* 8 x 6, sloped 1 1/2 to 1/4 1 pc /517 *ADA ftcompliant Important ft information ft Please noteft Scope of delivery ft Options ft Tileable surfaces Be sure to ask for a Certified Installer. Contact us: info@corp.com Find products & specs: corporation 1100 Landmeier Rd. Ste. 200 Elk Grove Village, IL Tel.: WEDI (9334) Fax: /13

13

14

15

16

17

18

19

20

21 Diese Zeichnung / Skizze ist Eigentum der GmbH und unterliegt dem Urheberrecht. Die Verwendung bedarf in jedem Fall der vorherigen, schriftlichen Zustimmung der GmbH this drawing and its copyrights are owned by GmbH.

22

23

24

25