Beton Trowel nv INSTRUCTION MANUAL. Wide Bay Truss SCREED BT405 - GEBABEBB BBRUBEBB BNP FORTIS: ING: BE BE

Size: px

Start display at page:

Download "Beton Trowel nv INSTRUCTION MANUAL. Wide Bay Truss SCREED BT405 - GEBABEBB BBRUBEBB BNP FORTIS: ING: BE81 0015 9813 5624 BE"

Toby Douglas
8 years ago
Views:

1 INSTRUCTION MANUAL Wide Bay Truss SCREED BT405 1/17

2 Table of contents Assembly 3 1 Section assembly 3 2 Engine assembly 6 3 End frame assembly 8 Operating instructions 9 1 Before operation 9 2 Starting 10 3 Stopping 10 4 Operating 10 5 Cleaning 11 Screed maintenance & service 12 1 A-frame replacement 12 2 Bearing replacement 13 3 Drive belt replacement 13 4 Greasing bearings 14 5 Long storage 14 Torque chart 15 1 Bearing locations 16 Parts 16/17 2/17

11 Screed maintenance & service 12 1 A-frame replacement 12 2 Bearing replacement 13 3 Drive belt

3 1 Section assembly Assembly 3/17

4 4/17

5 2 Engine assembly 5/17

6 6/17

7 3 End frame assembly 7/17

8 8/17

9 1 Before operation Operating instructions Check for damage to unit upon initial receipt and startup REMEMR! It is the owner s responsibility to communicate information on the safe use and proper operation of this unit to the operators. Before operating, review SAFETY PRECAUTIONS listed on page NO TAG of this manual. Familiarize yourself with the operation of the unit and confirm that all controls function properly FORE starting engine. Know how to STOP the unit. Make sure hands, feet and clothing are at a safe distance from any moveable parts prior to starting. Make sure winches, pulleys and cables move freely and are clean and lightly greased. OIL LEVEL Check the oil level in the engine. For more information see Engine oil in the engine Owner s Manual. AIR CLEANER Check to ensure element is in good condition and properly installed. Clean filter element if it s clogged. Replace it if it s damaged. FUEL SUPPLY The engines on BT N.V. Compaction equipment require a high grade of clean, fresh, unleaded gasoline. FUEL FILTER Check to ensure element is in good condition. Replace if if it s clogged or damaged. AIR REGULATOR UNIT Check to ensure there is an ample supply of Air Tool Oil in the oiler of the regulator unit. 9/17

Before operating, review SAFETY PRECAUTIONS listed on page NO TAG of this manual.

10 2 Starting 3 Stopping 4 Operating 10/17

11 5 Cleaning 11/17

12 1 A-frame replacement Screed maintenance & service 12/17

13 2 Bearing replacement 3 Drive belt replacement 13/17

14 4 Greasing bearings 5 Long storage Torque chart 14/17

15 1 Bearing locations 15/17

16 PARTS 16/17

17 Parts No. Desp bearing clutch assy shaft connector assy strength ring A shaft (2.54m) B shaft (1. 32m) C shaft(o. 71) eccentricity bush of shaft pulley eccentricity wheel of pulley rubber connector of shaft Winch Assy side frame assy T-plate L-plate conneet pipe tri-angle al frame(right) tri-angle al frame(left) short conneet plate adjust pipe (L, R) adjust bolt mounting plate for winch long conneet plate hole connector conneet plate of side frame Folk arm conneet assy mounting base for anti-wear plate belt cover engine mounting upper base engine mounting low base 17/17

5166001 T-plate 5166002 L-plate 5166003 conneet pipe 5166004 tri-angle al frame(right) 5166005 tri-angle al frame(left) 5166006 short conneet plate 5166007 adjust pipe 5166008(L, R) adjust bolt

Number Wheeler P/N Description Set Rex P/N Notes 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8)

Number Wheeler P/N Description Set Rex P/N Notes 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8