Operating manual SHEV-USB-100 BA-SHEV-USB E. BA-SHEV-USB E Date: Edition: Rev. 01/

Transcription

1 BA--10-E BA--10-E Operating manual Copyright by SIMON RWA Systeme GmbH Subject to technical modifications and errors. BA--10-E Date:

2 Table of contents 1. Table of contents 1. Table of contents General Installation Driver overview Install driver for Windows XP Setup Program Hyperterminal Generate connection (Icon) on the desktop Instruction Messages...8 BA--10-E Date: Page 2

3 2. General BA--10-E Operating manual General 3.2. Install driver for Windows XP The service cable () is used for visualization of operating states and messages. The Shev 3, respectively the Shev 6 can be connected via the service cable with laptop/computer and the messages can be issued. 3. Installation Attention! According to the version of the operating system or computer configuration the messages can differ from the representations. Attention! During the installation of the driver, the SHEV-USB- 100 must not yet be connected with the SHEV. Connect the USB-100 with the USB interface on your computer. The assistant for searching of new hardware starts automatically. Picture 1: 3.1. Driver overview Info For the installation of the driver, the CD has to be in the device. Driver Operating system Windows Server 2008 Windows Server 2008 x64 Windows Vista Windows Vista x64 Windows XP Windows XP x64 Windows 2000 Windows Server 2003 Windows Server 2003 x64 Choose Yes, this time only by clicking on the circle at the front. Then a black item appears in it. Picture 2: Windows 98 Windows ME Mac OS X (Intel) Mac OS X 1.0f4 Mac OS 9 Mac OS 8 Click on Next Linux Linux x86_64 BA--10-E Date: Page 3

4 Installation Choose Install from a list or specific location (Advanced). Picture 3: Now the software is going to be searched. Picture 5: Click on Next Please check if the highlighted figures in the window are choosen If the following window appears, choose the driver Picture 6: Picture 4: Click on Next. Click on Next. BA--10-E Date: Page 4

5 Installation Now the software is going to be installed. Picture 7: Accessories Communications HyperTerminal and click on Hyperterminal. As necessary the program can be set as a standard Telnetprogram. For that purpose click on Yes. If you do not want to be asked again, click on the button in front of Don t ask me this question again. If the button is activated, click on Yes. Picture 9: Picture 8: Choose the country Insert the area or city code Picture 10: Click on Finish to finish the assistant Now the software is installed Setup Program Hyperterminal Info The program hyperterminal is nonexistent at Windows Vista. Vista Users have to use an external Terminal program. Click on the button Start. Click on OK Then choose: All Programs BA--10-E Date: Page 5

6 Installation Picture 11: Info The number of the COM-Port can vary and depends on the already installed COM ports. Picture 13: Now enter the name of the connection (for example: ). And allocate any symbol to the connection by clicking (see Picture 12: ""). Approve the adjustments by clicking OK. Picture 12: Set up Baudrate of 9600 bits per second. By clicking on the bolt beside the window and choosing the 9600 in the opening menu. Check the following values: Data bits: 8 Parity: None Stop bit: 1 Flow control: Hardware Picture 14: Approve the COM device by clicking OK. Click on OK to resume the values. BA--10-E Date: Page 6

7 Instruction To finish installation, now click on the button Disconnect. Picture 15: Click on the file name.ht by holding right mouse button. Highlight in the opening menu Send to and click on Desktop (create shortcut). Close all opened windows Picture 17: Open menu item File and click on Saving. If you want to save this connection for a faster access on the desktop act as follows Generate connection (Icon) on the desktop Open menu item File and click on Open. Picture 16: 4. Instruction Connect the service cable () with the USB interface on your computer. Start the program Hyperterminal. Connect the service cable () with the pin 1 on the SHEV. Picture 18: 1 BA--10-E Date: Page 7

8 Messages Connect by pushing the icon Call. Picture 19: Every three seconds a report respectively operating state is passed. If there is no failure the message SHEV OK is indicated. 5. Messages Following messages are formed automatically depending on the operating state. The description appears bilingual: SHEV OK Alarm Stoerung / failure Empfohlene Entladeschlussspannung Akku erreicht / backup batteries achieved final discharging voltage Akku erreicht Tiefentladespannung, dies beeintraechtigt die Lebensdauer / backup batteries achieved depth discharge voltage - this influences batteries durability Ladeschaltung ausgefallen / charging circuit failure Lastsicherung ausgeloest / motor fuse failure Ueberlast am Motorkanal / overload motor output Akkuladung nicht freigegeben / backup batteries charging circuit not unlocked Ladeschaltung ausgeschaltet / charging circuit off Ueberlast Handausloesetaster / overload emergency button Ueberlast Rauchmelder / overload smoke detector Ueberlast BMZ / overload fire alarm signal Alarm von Handausloesetaster / alarm from emergency button Alarm von BMZ / alarm from fire alarm signal Alarm von Rauchmelder / alarm from smoke detector Akku defekt oder nicht angeschlossen / backup batteries failure or backup batteries are not attached Schleife Motor 1 unterbrochen / monitoring loop motor 1 failure Schleife Motor 2 unterbrochen / monitoring loop motor 2 failure Schleife Rauchmelder unterbrochen / monitoring loop smoke detector failure Schleife Handausloesetaster unterbrochen / monitoring loop emergency button failure Schleife BMZ unterbrochen / monitoring loop alarm signal failure Motor in Richtung AUF angesteuert / motor activated in direction open Motor in Richtung ZU angesteuert / motor activated in direction close SHEV befindet sich im Programmiermodus / SHEV programming mode is activated ZU-Befehl von Wind-Regenmelder / closing signal from wind/rain detector Alarm zurueckgesetzt / alarm has been reset Warten auf 2tes Zuruecksetzen am Handausloesetaster / waiting for second reset from emergency button Single messages can be indicated as combined. BA--10-E Date: Page 8