Sierra Pacific E-3 Clad Inswing Bi-fold Door Installation Guide
|
|
- Lucinda Wheeler
- 7 years ago
- Views:
Transcription
1 E-3 Clad Inswing Bi-fold Door Installation Guide Please read these instructions in their entirety prior to beginning the installation process. is not responsible for site measurements or the structural requirements for the installation of the Bi-fold door system. The weight of the door is carried by the header, therefore it is imperative that the top track be securely anchored to the header. We recommend the Bi-fold door system be installed with a minimum of two people; one person handling the door panels and the other person attaching and adjusting hardware. Caution panels can be extremely heavy and awkward to handle. We also recommend that all components be finished prior to installation. Otherwise special care is needed in labeling components during the un-assembling process, thus allowing ease in the reassembling process. All hardware holes have been pre-drilled. Do not drill any holes during assembly. Materials Required SPW Bi-fold Drawing Flexible Flashing 9"(Supplied by SPW) Shims Sill Pan 1-tube SM-8500 Acrylic Sealant (supplied by SPW) Batt Insulation Tools Required Tape Measure Laser Level (recommended) 3 Foot Level 6 Foot Level Ladders Screw Gun 6" Square Tip Bit (#3) Caulking Gun 10" -12" #2 Phillips Screwdriver 10" -12" 3/8" Blade Screwdriver 1. Before Frame Assembly (Preparation) Head track & jamb Install mohair weatherstrip (provided in one long length). (see drawing-1) (drawing-1) Mohair
2 Refer to your SPW Bi-fold drawing to determine your specific door set-up. Load head track: top pivot - left or right carrier sets - intermediate carrier set. (see drawing-2) PAY SPECIAL ATTENTION TO ASSURE PROPER DIRECTION WHEN INSTALLING RIGHT OR LEFT CARRIER SETS SEE THE ATTACHED ELEVATION DRAWING FOR THE SPECIFIC HARDWARE PLACEMENT OF YOUR DOOR. LEFT CARRIER RIGHT CARRIER (B) (A) INTERMEDIATE CARRIER TOP PIVOT (C) RIGHT CARRIER This edge should always be towards the exterior of the panel (drawing-2) (A) (B) (C) PANEL #1 PANEL #2 PANEL #3 PANEL #4 VIEWED FROM EXTERIOR
3 Sill No pre-assembly preparation required. Side Jambs No pre-assembly preparation required. 2. Assembling The Frame Head - (use screws from bag marked "head"). Apply SM-8500 acrylic sealant (supplied by SPW). Apply a 1/4" bead of sealant as shown. Install the corner key through the corner gasket and into the aluminum clad keyway on head and jamb cladding. Insert #6 X 1 1/2"self tapping screw into pre-drilled hole to secure the clad corner. Use #7 X 2 1/4" screws to fasten the wood portion together. (see drawing-3) SM-8500 Sealant Application Corner Gasket (factory applied) #7 x 2 1/4" Wood Screws Aluminum corner key Self-Tapping Screw (drawing-3)
4 Assembling The Frame (Continued) Sill - (use screws from bag marked "sill") Apply the double stick sill gasket. When fastening frame to sill, make sure to have solid compression of the gasket. After sill is fastened to the jamb, apply SM-8500 sealant to the underside of sill and sidejamb joint. After sealant is applied, wrap Vycor flashing around the bottom corner of the sill, covering the sealant joint (at least 4" up jamb & 4" across bottom of sill). (see drawing-4) Vycor Flashing Sealant Sill Gasket (drawing-4) Guides for Self-Tapping Screws #7 X 2 1/4" Self-Tapping Screws Head - Install head drip cap. The bottom leg of drip cap will snap into the accessory kerf on the frame. Use a rubber mallet or wood block and hammer to prevent damage to the drip cap. (see drawing-5) Apply butyl corner pad. (see drawing 6) Head Drip Cap Butyl Corner Pad (drawing-5) (drawing-6)
5 3. Installing & Flashing the Frame It is the responsibility of the installer / contractor to verify compatibility of sealants, flashing and all envelope membrane drainage system components. It is also the responsibility of the installer / contractor to verify that the floor / subfloor is flat and level prior to installation. If a metal sill pan is used, (recommended) it is the responsibility of the installer / contractor to verify compatibility of metals to eliminate the possibility of galvanic reaction. Dry fit frame to rough opening. Make sure opening specifically the sub floor, or concrete is dry, clean and free of dirt and debris. The sill should be installed flat and straight. The installation of a bi-fold door system requires that the head and jambs are square and straight. We recommend that the head be installed with a slight upward bow 1/8" at the center of door rough opening. (see drawing-7) 3" screws to be used in the head (fill every pre-drilled hole). Clean inside track along roller path. Bottom pivot screws and sealant is all that is required at sill. (Frame and Flashing installation information on the following pages) 1/8" +/- 1/8" (drawing-7) EXTERIOR VIEW
6 Clad Frame Installation & Flashing Information Please read Frame & Flashing instructions carefully and thoroughly before starting. Installation of Frame: 1. Check rough opening to insure that opening is level, plumb and square. Verify that width and height dimensions are correct. Rough opening should be ¾ wider than overall frame height and width. Sill plate or concrete slab should be flat and level. Make sure opening, specifically the sub floor (or concrete), is dry, clean and free of dirt and debris. NOTE: Flashing and/or an appropriate method of sealing shall be designed as a part of an overall weather resistive barrier system. It is not the responsibility of the door manufacturer to design or recommend a flashing system appropriate for each job condition. Fig 1 4 Apply two continuous beads of polyurethane sealant across the width of the sill, approximately ½ - 1 inch in from the interior and exterior edges of the RO (see fig 2). The sealant should extend 6 inches up each side of frame members. Set the sill pan in place (see fig 3) and make sure that it is fully seated in the sealant. Flashing material is recommended to be at least 9 wide. Any variance from this installation procedure signifies that proper waterproofing becomes the responsibility of the design professional and/or the installer. 2. Sill pan. strongly recommends the use of a sill pan. 3. An overview of the proper flashing sequence is shown in (see fig 1) Fig 2
7 6. Apply a continuous nominal bead of polyurethane sealant along the backside of the nailing flange along both side jambs and head. Run additional sealant across the 45 joint where the flanges meet (see fig 5). Make sure butyl pad is in good condition and adhering properly. Fig 3 Fig 5 7. Insert and center the bi-fold frame in the rough opening. When doing so, tilt the frame back so that the sill can be set into the opening and onto the sealant. Avoid scraping the sealant off the sill pan (see fig 6). Fig 4 5. Once in place, apply a bead of sealant just above the back corner of the sill pan. The bead should be continuous and extend across the entire length of the sill pan. A discontinuous bead should then be applied near the exterior edge of the sill pan. It is recommended that the door frame be set onto1/8 plastic shims set in the sill pan. (see fig 4) This will allow any water caught by the pan to drain out. Shims should be spaced 1-2 from each end, then approximately every 12 thereafter. Fig 6 8. With the frame set into the rough opening, check to make sure it is centered. Tack the door in place with one 1-1/2 stainless steel (non-corrosive) screw in the top nailing flange within 3-6 of each corner. Make sure that the sill is straight, flat and level. Use a tape measure to measure the horizontal and diagonal dimensions of the frame to
8 ensure the frame is plumb and square (see fig 7). These measurements should be double-checked by using a framing square and level or straight edge to ensure the jambs are straight. Shim at the side jambs as required. Fig 7 9. Once the frame is square, level and plumb, finish securing the nailing flange. 10. Secure the nailing flange to the sheathing with 1-1/2 stainless steel (noncorrosive) screws, beginning 4 inches from the corner and thereafter. Fig The length of the head flashing should equal width of RO + (2x width of the flashing material) + 2. Extend 1 beyond edge of each side flashing (see fig. 9). Attach top edge of flashing to the wall. 11. Place a small amount of polyurethane sealant over each screw head. 12. With the unit completely secured to the structure, apply a bead of polyurethane sealant at the edge of the head jamb nailing flange where it meets the sheathing. Also, apply similar beads of sealant between the edge of the side jamb nailing flange and the sheathing material. Tool the sealant into the joint to ensure the joint is filled. 13. Apply a layer of flashing over the side jamb nailing flange (see fig. 8). The length of the flashing should equal the height of the RO + (2x width of the flashing material) 1. Install the flashing so that the edge contacts the inside corner of the nailing flange. The top of the flashing should extend only 8-1/2 above the top edge of the window frame. Repeat for opposite side. Fig 9
9 4. After The Frame Has Been Installed Refer to your SPW Bi-fold drawing to determine your specific door set-up. Install Wall pivot assembly (Required only if Bi-fold is taller than 88"). Wall Pivot cylinder and screw holes are pre-drilled by SPW. (see drawing-8) You will be required to pre-drill the trimmer prior to installing the wall pivot. (see drawing -8a) Install bottom pivot block assembly. (see drawing-9) (drawing-8) Rough Opening Door Frame 1/2" (drawing-8a) WALL PIVOT ASSEMBLY Wall Framing Cylinder Hole (drawing-9) BOTTOM PIVOT BLOCK ASSEMBLY
10 5. Door Panel Preparation Panels are numbered at the top (as shown). Lay out in numerical order (always from left to right.) (see drawing-10) (drawing-10) VIEWED FROM EXTERIOR Install hinges (hinge screws holes are pre-drilled), tighten the screws on the wood side before installing the screw into the clad. Do not over tighten screws into the clad. (see drawing-11) Refer to the legend on the SPW Bi-fold drawing of your door for proper hinge type placement. Secure this screw first. (drawing-11)
11 Door Panel Preparation (Continued) Install mohair weatherstrip on bottom of panels. Slide weatherstrip in from end of aluminum track. Crimp the ends of the aluminum track once weatherstrip is in place. (see drawing 12) Install flush bolts at the top and bottom of the interior face of the panels to which they apply. (see drawing 13) (drawing-12) Bottom of Panel Flush Bolt Plate (mounted into frame head jamb) Mohair Weatherstrip (drawing-13) Flush Bolt Flush Bolt Flush Bolt Plate (mounted onto frame sill) VIEWED FROM INTERIOR
12 6. Installing the Panels Always start at the jamb and work towards the center (this may require working inward from both ends). Begin panel installation at the bottom pivot block located at sill. Place 5/16 " shim (supplied by SPW) on top of protected sill, allowing the panel to rest on shim. This helps pre-set the correct height of panel and hinge screw alignment. (see drawing-14) Continue with next panel (drawing-14) Shim 7. After All Panels are Installed Open and close very slowly for the first time! Do not force anything. Make vertical and horizontal adjustments until the panels clear any hangups. Install the weatherstripping for the individual door panels. (see drawing-15) Weatherstrip should butt up against each hinge & be cut flush with the top and bottom of the panels. After door panel has been stained or painted, apply hinge gaskets around one leaf of each hinge. (see drawing-16) Panel Weatherstip Frame Stop Weatherstrip (drawing-16) (drawing-15) Hinge Gasket
13 8. Adjust the Door Panels 3/16" gap between top of the doors, and the top track. 3/8" gap between the bottom of the doors and the bottom track (not including protective sill covering) 9/32" gap on side panels to frame. (see drawing-17) (drawing-17) 3/16" 3/8" 9/32" Horizontal adjustment is achieved by using a 10" - 12" philips head screwdriver (see drawing-18) Vertical adjustment is achieved by using a 10"-12" standard head screwdriver at the top pivots and carriers (see drawing-19) After final adjustments remove adjustment clips (save for later adjustments). Install flush bolt plates in head (E-3) Top Horizontal Adjustment Vertical Adjustment Bottom Horizontal Adjustment Adjustment Clip (drawing-19) (drawing-18)
14 9. Install Interior Stops Install exterior head stop first (stops are shipped rough cut). Place wood blocking against head track. Position exterior head stop 5/16" out from the exterior face of the panel. (see drawing-20) Install weatherstrip into head stop kerf. (see drawing-20a) Place side jamb exterior stop flush with head jamb stop. (see drawing-21) Install strike plate as required. Install door hardware as required. Weatherstrip 5/16" 1/8" Head Stop (drawing-20) (drawing-20a) Jamb Stop (drawing-21) Astragal 10. Astragal Not all doors will require an astragal. The top of the astragal should be placed flush with the top of the panel. The bottom of the astragal should be approximately 1/8" above the threshold. (see drawing-22) 5/32" 1/8" (drawing-22)
Clad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
More informationWindow Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
More informationWINDOW INSTALLATION GUIDE FOR NEW CONSTRUCTION - WOOD FRAMING
WINDOW INSTALLATION GUIDE FOR NEW CONSTRUCTION - WOOD FRAMING IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing windows. Any local building code requirements
More informationSun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationReplacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin americancraftsmanwindows.com Project Requirements: Failure to follow these instructions may void product
More informationBasement Window Installation Guide Hopper and Sliding
Basement Window Installation Guide Hopper and Sliding americancraftsmanwindows.com Project Requirements: Installation must comply with all applicable building codes. Existing window frame, wall and weatherresistant
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationINSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2009 Pella Corporation INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Part Number: 80WH0100 Installation Instructions for Typical Wood Frame Construction.
More informationInstallation Guide for Andersen Architectural Clad Outswing Commercial Doors
Installation Guide for Andersen Architectural Clad Outswing Commercial Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen Architectural Wood Inswing Entry Doors
Installation Guide for Andersen Architectural Wood Inswing Entry Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are
More informationSLIDING PATIO DOOR INSTALLATION INSTRUCTIONS USING FRAME SCREWS
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V984528 2012 Pella Corporation SLIDING PATIO DOOR INSTALLATION INSTRUCTIONS USING FRAME SCREWS Installation Instructions for Typical
More informationWHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
More informationWINDOW INSTALLATION GUIDE
WINDOW INSTALLATION GUIDE is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic information
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows without Nailing Fin (JII011) ImPOrTANT INFOrmATION & GlOssAry. rough OPeNINGs
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl windows without a nailing fin (including finless, flush fin and flange). Read these instructions
More informationINSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg
Thank you for selecting JeLd-weN products. Attached are JeLd-weN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationREDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES
REDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES Tools Required Tape Measure Hammer Slotted Screw Driver #2 & #3 Philips Screw Driver 3-4 Foot Level 12 Pry Bar Cold Chisel
More information4 5/16 Subframe Installation
4 5/16 Subframe Installation The subframe system is a great installation tool for installing windows in masonry conditions. Typically subframes are used in masonry openings so that windows can be anchored
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationWELCOME. Recommended Window Installation. 1.5 credits Minnesota Department of Labor and Industry
WELCOME Recommended Window 1.5 credits Minnesota Department of Labor and Industry In accordance with the Department of Labor and Industry s statute 326.0981, Subd. 11, This educational offering is recognized
More informationBrick Veneer Construction
Brick Veneer Construction Check list of suggested tools & support items Claw hammer Tape measure 3/4" [19 or 20] Wood chisel Wood or plastic shims Pry bar Utility knife Caulking and caulking gun Power
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationInsulView Window Installation Instructions
InsulView Window Installation Instructions 1. The entire building is normally sheeted with the 2" 2 ½ OR 3 wall panel and the windows installed at a later time. A window retrofit of an existing building
More informationTechnical data sheet PVC Bi-fold doors
Standard Specifications White internally beaded, Deceuninck 3000 series profile 28mm Low-e toughened sealed units with argon gas Open in doors with white handles and hinges Tracks are fitted to the top
More informationTundra Series Windows January 2016
Tundra Series Windows January 2016 New Construction Installation Instructions Nail Fin, J-Fin and Brickmold Aplications product. ATTENTION! Read and understand all installation instructions before installing
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW
Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Lea las instrucciones en español en el reverso.
More informationK. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11
K. D. FRAME ASSEMBLY FOR MASONRY WALLS...........................Ins 2 FRAME INSTALLATION DETAILS FOR MASONRY WALLS......................Ins 3 INSTALLING EXISTING MASONRY WALL ANCHORS IN FRAME..................Ins
More informationReplacement Installation Instructions
Sliding Door Replacement Installation Instructions Please make sure you have: Fixed 1 - Operating (X) Panel (Glazing Bead Inside, Roller Adjustment Holes Outside) 1 - Fixed (O) Panel (For 3-Panel doors,
More informationINSTALLATION INSTRUCTIONS for Swinging French and Patio Doors (JII105)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Steel, Fiberglass, Vinyl, and Wood French and Patio Doors. Read these instructions thoroughly
More informationMarch 14, 2007. Installation of Bay, Bow and Garden Windows
March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed
More informationILLUSION FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
PREPARATION Approximate Installation Time: Tools Required for Installation: 60 minutes Hacksaw Electric Drill 3/16 Masonry Bit Pencil/Felt tip pen Safety Glasses Measuring Tape Masking Tape Standard Screw
More informationINSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin (JII006)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl Patio Doors with nailing fin. Any local building code requirements supersede the recommended
More informationPANELIZED HOME INSTALLATION GUIDELINE
PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.
More informationVinyl Greenhouse Window Page 2 of 6 New Contruction Installation Instructions
New Construction Installation Instructions EPLACEMENT Installation Instructions Page 2 of 6 New Contruction Installation Instructions 1. Frame rough opening equal to window call out size. ough opening
More informationTherma-Tru Slim-Line Sliding Patio Door. Assembly and Installation
Therma-Tru Slim-Line Sliding Patio Door Assembly and Installation Read all instructions before starting. Builder or subcontractor, please forward these instructions to the homeowner. The applicable standards
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION AND GLOSSARY ROUGH OPENINGS
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nail fin. Not all window types may be installed into every wall
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More information450 SERIES SLIDING GLASS DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
450 SERIES SLIDING GLASS DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS Effective 2/12/11 Revised 7/7/15 TACOMA, WA (253) 922-6030 PORTLAND, OR (503) 682-3270 MARYSVILLE, WA (360) 659-0836 SACRAMENTO, CA
More informationAll-Season Sunroom Sliding Glass Door Installation Instructions
ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationSash Replacement Guide
for Andersen 200/400 Series Awning Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen at 1-888-888-7020
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationHinge, Blocker, and Tab Adjustment Guide
Hinge, Blocker, and Guide for Andersen A-Series Hinged Outswing; 400 Series Frenchwood Hinged Outswing Patio Doors and 400 Series Frenchwood Hinged Outswing Patio Doors with Stormwatch Protection Hinge,
More informationIMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Step 1:
IMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Thank you for purchasing your new replacement windows from Great Lakes Window. The following instructions will help remove the old windows
More informationWINDOW PANNING AND TRIMS
OCTOBER, 2010 PANNING AND TRIMS GENERAL INFORMATION 1 EXTERIOR PANNING Panning is primarily used to cover the perimeters of existing building openings prior to the installation of replacement windows.
More informationAAMA 2400-10. Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure
A M E R I C A N A R C H I T E C T U R A L AAMA 2400-10 Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure M A N U F A C T U
More informationSERIES 238 WINDOWS. NOTE: Read instructions completely before attempting any installation.
1 Installation Instructions SERIES 238 WINDOWS Page 2: Page 3-4: Page 5: Page 6: Page 7: Opening Preparation and Wood Buck Installation Installation Instructions for Series 238 WINDOWS Figure 1: Buck preparation
More informationHeavy Glass Frameless Shower Door With Return Panel
202 Anderson Ave., elvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com Heavy Glass Frameless Shower Door With Return Panel Full Showers with Return ench Seat with Return FRLSDRPL-0116
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Denver. 12'x 12' or 12'x16' Revised November 29, 2010
Best Barns USA Assembly Book Revised November 29, 2010 SAMPLE INSTRUCTIONS the Denver 12'x 12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775
More informationDESIGN AND CONSTRUCTION GUIDELINES AND STANDARDS DIVISION 8 DOORS AND WINDOWS 08 50 00 WINDOWS
SECTION INCLUDES Metal Windows Vinyl/Aluminum Clad Wood Windows Solid Fiberglass and Vinyl Windows Wood Windows (Historic Preservation only) RELATED SECTIONS 02 83 00 Lead Paint Remediation 06 10 00 Rough
More informationImportant Information for Installer & Homeowner
Important Information for Installer & Homeowner Homeowner: Please keep this information for your records, do not discard! Installation Instructions for Wood Frame Construction Replacement (See other side
More informationHinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005
Hinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005 For ease of installation and continued enjoyment of your Andersen product,
More informationHALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL
HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps
More informationISSUE 2. Installation Guide
ISSUE 2 Installation Guide Here at Slide and Fold, we LOVE our Bi-Fold Plus range of folding-sliding doors. We want to ensure that your customers love them too. So we have created a new, detailed installation
More informationBarewood Octagon and Elongated Windows Installation Instructions
Step-by-step instructions to a beautiful window. Measuring and Installation of your new window from Century Specialty Windows couldn't be easier with our step-by-step instructions. Quality, function and
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationPackaged Terminal Air Conditioner Wall Sleeve Installation
Installation & Maintenance Data IM 1196 Group: PTAC Part Number: 910141799 Date: October 2013 Packaged Terminal Air Conditioner Installation x 42" PGAN with Top-Mounted Hydronic Heat Note: Installation
More informationActive and Passive Sash Replacement
for Andersen Gliding Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete the procedure, call Andersen at 1-888-888-7020 for
More informationFree 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details
Free 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details Brought To You By: MyShedPlans Click Here To Download 12,000 Shed Plans >> 12 x 8 Basic Shed This 8 12-ft. shed features a simple
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationOwner's Manual & Assembly Instructions
Owner's Manual & Assembly Instructions PM01 BASE KIT Model No. FDN1014 717090311 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY
More informationOUTSWING & INSWING ENTRANCE DOOR
OISED OUTSWING & INSWING ENTRANCE DOOR INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING ANY INSTALLATION CAUTION Lead-based paint may be present in older homes, and the removal
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationINSTALLATION INSTRUCTIONS for Vinyl Patio Doors without Nailing Fin (JII015) IMPORTANT INFORMATION AND GLOSSARY
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl patio doors without nailing fin, including flush fin. Read these instructions thoroughly
More informationThe WANZ Guide to Window Installation
The WANZ Guide to Window Installation as described in E2/AS1 Amendment 5 Ver. 1.1 Page 2 of 74 Contents Overview Page 5 Objective Page 5 Scope Page 5 Opening Preparation Page 7 Step P1 Preliminary Check
More information300mm. 2mm MIN GAP. PLACE 100mm X 100mm. SO THAT IT IS 38mm INTO
INSTALL PEEL & STICK (P&S) GUSSETS WITH PRIMER AS PER MANUFACTURERS INSTRUCTIONS 2mm MIN GAP IN SHEATHING STEP 1 PLACE 100mm X 100mm PIECE OF P&S IN CORNER SO THAT IT IS 38mm INTO THE OPENING EACH WAY
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More information7. Installation. installation 7.1.1. CAST-IN WINDOW SYSTEM 7.1. INSTALLATION OF WINDOW MAIN FRAME
7. Installation Window involves the fixing of window frame at an earlier construction stage and subsequent of the window sashes. This is a highly workmanship dependent process. Only trained and approved
More informationINSTALLATION RECOMMENDATIONS. Outdoor Rubber Tiles
INSTALLATION RECOMMENDATIONS Outdoor Rubber Tiles Prior to Installation: The Outdoor Rubber Tiles and accessory transition pieces intended for this installation have been shipped to you via a freight carrier
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationHfHMD uses LP SmartSide siding and trim.
HfHMD uses LP SmartSide siding and trim. These products are: More durable than cement fiber board. Much more volunteer-friendly to install. When installed correctly, have a 5/50- year pro-rated warranty.
More informationSECTION 6. Glass Storefront Doors:
SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail
More informationInstallation Manual. Toilet Partitions, Dressing Compartments & Shower Stalls
Installation Manual Toilet Partitions, Dressing Compartments & Shower Stalls Metpar Corp 95 State Street, Westbury, New York, USA, 11590 Tel: 516-333-2600 Fax: 516-333-2618 Internet: http://www.metpar.com
More informationSuperform Products Ltd.
TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000
More informationGreenGuard Housewrap Installation Guide
000768PACBPHW_Flashing Bro 5/23/03 2:52 PM Page 1 For the most current product information, go to www.green-guard.com. Pactiv Building Products believes the information and recommendations herein to be
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationHow To Install Your Frameless Shower Enclosure
How To Install Your Frameless Shower Enclosure a) Installing Single Frameless Door Side Mounted Wall Hinges b) Installing Frameless Door with In-Line Panel c) Installing Frameless Door Between In-Line
More informationCable Support System Guide for Andersen Bow, Bay, and Box Projecting Window Units
for Andersen Bow, Bay, and Box Projecting Window Units Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationInstallation Instructions
Installation Instructions 1. Position the unit onto bridging packers. These keep the unit away from any water sitting inside the frame. 2. Centralise the unit within the frame and pack the edges with appropriate
More informationNew Construction Stud Frame Vinyl Window Installation Guide
New Construction Stud Frame Vinyl Window Installation Guide This manual contains procedures based on ASTM E2112 and Installation Masters Installer Training & Certification Program Manual RLC-1 The procedures
More informationTable of Contents. Western States RustWall Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide
Western States RustWall Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer /Installers.. 1 Fastener Placement and Selection.2-3
More informationMIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida
Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B8049.01-401-18 Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida PRODUCT TYPE: Aluminum Storefront with Double Doors SERIES/MODEL:
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationEntry Door System Installation Instructions
Entry Door System Installation Instructions IMPORTANT Read these instructions completely before beginning installation. Please use caution when completing any building project. Safety glasses Phillips
More informationHOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationInstallation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step
More informationmajestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base
majestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base These Instructions are for a left and right handed unit. The diagrams show a left
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationPART 1 GENERAL 1.1 SECTION INCLUDES
J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationEucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in handling.
i This instruction sheet describes the proper methods for installing Eucatex decorative wall paneling. Eucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in
More informationThe better way to build TM. Installation Manual. FOUNDATION SIPs & FROST WALLS SIPs
The better way to build TM Installation Manual FOUNDATION SIPs & FROST WALLS SIPs February 2016 PWF FOUNDATION & FROST WALL SIPs Installation Manual Table of Contents Topics General Requirements...................................
More information