Multilayer Ceramic Chip Capacitors

Transcription

1 Middle & high voltage MLCC is a kind of special design special technology MLCC that bases on the technology of general MLCC. This kind of MLCC has stable high voltage reliability and suitable to SMT. Middle & high MLCC is widely applicable for many direct high voltage circuits in which it can improve the performance of the circuit. Features Series size from 060~2225 Working from 100V~5000V Surface mount suited for wave and reflow soldering Wide Operating temperature range from Good Coefficient High reliability Dimension How To Order HC 1206 X7R 105 K 500 P Product Code HV=High Size Dielectric C0G=NPO X7R X5R Unit : pf 0R5=0.5pF Tolerance A=±0.1pF B=±0.2pF C=±0.25pF Rated 6R=6.6V 500=50V Termination P:Ag/Ni/Sn S:Ag/Pd/Pt 1210 Y5V D=±0.5pF 102=1000V 2R5=2.5pF HA=Safety 1808 Z5U F=±1% 202=2000V Capacitors HC=High = G=±2% J=±5% 502=5000V 2225 K=±10% M=±20% Z=+80%/-20% CHIPTCR ELECTRONICS CO.,LTD Tel: (+86) , , Fax: (+86) Page 1 of 5

2 Range Size Rated Range Inch(mm) C0G(nF) X5R(nF) X7R(nF) Y5V(nF) 6.V 1,000~2,200(225) 1,000(105) 1,000(105) V 1,000(105) 100(104) 1,000(105) (1005) 16V 1,000(105) 100(104) 6.V 1~22(22) 1,000~10,000(106) 1,000~2,200(225) 1,000~4,700(475) V 1~10(10) 1,000~4,700(475) 1,000~2,200(225) 1,000~4,700(475) (1608) 16V 1~.(2) 1,000~2,200(225) 1,000(105) 1,000~2,200(225) 25V 1~.(2) 1,000(105) 1,000(105) 6.V 1,000~47,000(476) 1,000~10,000(106) 1,000~22,000(226) 10V 1~100(104) 1,000~22,000(226) 1,000~10,000(106) 1,000~10,000(106) V 1~() 1,000~10,000(106) 1,000~4,700(475) 1,000~10,000(106) (2012) 25V 1~22(22) 1,000~4,700(475) 1,000(105) 1,000~4,700(475) 50V 1~10(10) 1,000(105) 1,000(105) 1,000~2,200(225) 6.V 1,000~10,000(107) 1,000~100,000(107) 10V 1,000~47,000(476) 1,000~22,000(226) 1,000~47,000(476) V 10~100(104) 1,000~22,000(226) 1,000~10,000(106) 1,000~22,000(226) (216) 25V 10~47(47) 1,000~10,000(106) 1,000~10,000(106) 1,000~10,000(106) 5V 1,000~4,700(475) 1,000~4,700(475) 1,000~10,000(106) 50V 1~() 1,000~4,700(475) 1,000~4,700(475) 1,000~10,000(106) 6.V 1,000~100,000(107) 1,000~100,000(107) 10V 1,000~47,000(476) 1,000~47,000(476) 1,000~47,000(476) V 1,000~47,000(476) 1,000~22,000(226) 1,000~47,000(476) (225) 25V 10~100(104) 1,000~22,000(226) 1,000~10,000(106) 1,000~22,000(226) 5V 1000~10,000(106) 1,000~10,000(106) 1,000~10,000(106) 50V 10~47(47) 1,000~10,000(106) 1,000~10,000(106) 1,000~10,000(106) 6.V 1,000~100,000(107) 1,000~100,000(107) 10V 1,000~100,000(107) 1,000~47,000(476) 1,000~100,000(107) V 10~220(224) 1,000~47,000(476) 1,000~47,000(476) 1,000~47,000(476) (452) 25V 10~120(124) 1,000~22,000(226) 1,000~22,000(226) 1,000~22,000(226) 50V 10~100(104) 1,000~10,000(106) 1,000~10,000(106) 1,000~10,000(106) 6.V 1,000~100,000(107) 10V 1,000~100,000(107) V 1,000~47,000(476) 1,000~47,000(476) 1,000~100,000(107) (5750) 25V 1,000~22,000(226) 1,000~22,000(226) 1,000~47,000(476) 50V 1,000~10,000(106) 1,000~10,000(106) 1,000~22,000(226) We can design according to customer special requirements CHIPTCR ELECTRONICS CO.,LTD Tel: (+86) , , Fax: (+86) Page 2 of 5

3 HV Series & Operation -55 to +125 Visual No abnormal exterior appearance Visual Inspection Within The Specified Tolerance Class Frequency Quality Factor Dissipation Factor More Than 0pF : Q pF & Below: Q C Maximum (C:Cap., pf) NPO C 100pF C>100pF X7R 1MHz±10% 1KHz±10% 1KHz±10% Perform a heat temperature at 150±5 for 0min. then place room temp. for 24±2hr. 1.0±0.2Vrms 1.0±0.2Vrms Withstanding 10,000MΩ or 500/C Ω whichever is smaller. No dielectric breakdown or mechanical breakdown V 500V, Rated V> 500V, Applied 500Vdc Charge Time : 60sec. Is applied less than 50mA current. 200V V<500V : 200% Rated 500V V<1000V: 150% Rated 1000 V :120% Rated for 1~5 sec. Current is limited to less than 50mA. Withstanding voltage testing requires immersion of the element in a isolation fluid prevent arcing on the chip surface, at voltage over 1000Vdc. Coefficient Char. NPO(N) X7R (X) Temp. Range -55 ~ ~ +125 Cap. Change ± 0ppm/ ± 15% ClassΙ: [C2-C1/C1(T2-T1)] 100% ClassⅡ: (C2-C1)/C1 100% T1:Standard (25 ) T2:Test C1: At Standard C2: At Test Adhesive Strength of Termination No indication of peeling shall on the terminal electrode. 5N f A 5N f( 0.5Kg f) pull force shall be applied for 10±1 sec. to Flexure of Substrate No mechanical damage or capacitance change more than the following table. Char. NPO(N) X7R (X) Change ± 5.0% of initial ± 12.5% of initial The board shall be bend 1.0mm with a rate of 1.0 mm/sec. C Meter R20 Bending Limit 45±1mm 45±1mm Solderability More than 90% of the terminal surface is to be soldered newly, so metal part does not come out or dissolve. Solder : 245±5 Dip Time : 5 ± 0.5 sec. Immersing Speed : 25±10% mm/s Solder Flux Preheat : H6A :Rosin : At 80~120 For 10~0sec. CHIPTCR ELECTRONICS CO.,LTD Tel: (+86) , , Fax: (+86) Page of 5

4 HV Series & to Soldering Heat ClassⅡcapacitor shall be set for 48± 4 hours at room temperature after one hour heat treatment Within 2.5% or ±0.25pF whichever is larger of initial at /-10 before initial measure. Preheat : at 150±10 C for 60~120sec. Dip : solder temperature of 260±5 Dip Time : 10 ± 1sec. Within ±10% of initial Immersing Speed : 25±10% mm/s Solder Flux : H6A : Rosin Class Ⅰ: 24 ± 2 Hours Class Ⅱ: 48 ± 4 Hours Cycle ClassⅡ capacitor shall be set for 48±4 hours at room temperature after one hour heat Within 2.5% or ±0.25pF whichever is larger of initial treatment at /-10 before initial measure. Capacitor shall be subjected to five cycles of the temperature cycle as following: Within ±7.5% of initial Step Temp.( ) Time(min) 1 2 Min Rated Temp.+0/- (-55) 25 Max Rated Temp.+/-0 (125) ClassⅠ: 24 ± 2 Hours ClassⅡ: 48 ± 4 Hours Humidity Within 5% or ±0.5pF whichever is larger of initial Within ±15% of initial ClassⅡ capacitor shall be set for 48±4 hours at room temperature after one hour heat treatment at /-10 before initial measure. : 40± 2 Relative Humidity : 90 ~95%RH Test Time : /-0 hr More Than 0pF : Q 50 0pF & Below: Q C Maximum ±5.0% ClassⅠ: 24 ± 2 Hours ClassⅡ: 48 ± 4 Hours 1,000MΩ or 50/C Ω whichever is smaller. CHIPTCR ELECTRONICS CO.,LTD Tel: (+86) , , Fax: (+86) Page 4 of 5

5 HV Series & High Load (Life Test) No mechanica damage shall Class Ⅱ capacitors applied DC voltage (following table) is applied for one hour at maximum operation temperature ± then shall be set for 48±4 hours at room temperature and the initial Within % or ±0.pF whichever is larger of initial measurement shall be conducted. Applied : Within ±15% of initial More Than 0pF : Q 50 Rated 250Vdc >250Vdc < 1KVdc 1KVdc Applied 150%Rated 120%Rated 100%Rated 0pF & Below: Q C Maximum ±5% 1,000MΩ or 50/C Ω whichever is smaller. : max. operation temperature Test Time : /-0Hr Current Applied : 50 ma Max. Class Ⅰ: 24 ± 2 Hours Class Ⅱ: 48 ± 4 Hours Vibration Solder the capacitor on P.C. board. Vibrate the capacitor with amplitude of Within the specified tolerance 1.5mm P-P changing the frequencies from 10Hz to 55Hz and back to 10Hz in about 1 min. Repeat this for 2 hours each in perpendicular directions. CHIPTCR ELECTRONICS CO.,LTD Tel: (+86) , , Fax: (+86) Page 5 of 5