SPM series. Inductors for Power Circuits. Wound Metallic Magnetic Material
|
|
|
- Bertina Owens
- 7 years ago
- Views:
Transcription
1 September 2014 Inductors for Power Circuits Wound Metallic Magnetic Material SPM series SPM3012 SPM3015 SPM3020 SPM4012 SPM4015 SPM4020 SPM5012 SPM5015 SPM5020 SPM5030 SPM6530
2 (2/49) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40 C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
3 (3/49) Inductors for Power Circuits Wound Metallic Magnetic Material Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Overview of the SPM Series FEATURES Magnetic shield type wound inductor for power circuits using a metallic magnetic material. Low-profile product lineup with max. heights of 1.2mm, 1.5mm, 2.0mm and 3.0mm allowing for different usages. Compared to ferrite wound type inductors, it is possible to achieve large current, low Rdc, and compactness. Low inductance variance in high-temperature environments with good DC superimposition characteristics. Metallic magnetic material is used, and the structure has an integrated molded coil, so hum noise is lower than with core adhesive coils. APPLICATION Smart phones, tablet terminals, laptop computers, HDDs, servers, VRMs, compact power supply modules, other PART NUMBER CONSTRUCTION SPM 3012 T - 1R0 M Series name L W H Dimensions (mm max.) Packaging style Inductance Inductance (μh) tolerance T Taping 1R0 1.0 M ±20% 1R R SPM 6530 T - R25 M 230 Series name L W H Dimensions Inductance Inductance Packaging style (mm max.) (μh) tolerance T Taping R M ±20% 1R R7 4.7 Internal code OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Temperature range Operating temperature Storage temperature Package quantity C C (pieces/reel) g Individual weight SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to SPM to to Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
4 (4/49) Overview of the SPM Series RECOMMENDED REFLOW PROFILE Preheating Soldering Peak T4 Natural cooling T: Temperature T2 T3 t3 T3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150 C 180 C 120s 230 C 30s 260 C 10s max.
5 (5/49) SPM series SPM3012 Type SHAPE & DIMENSIONS 3.2± ±0.1 (1.5) 0.85± ± ± max. 1.5±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
6 (6/49) SPM series SPM3012 Type CHARACTERISTICS SPECIFICATION TABLE L L measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc2 1.0 ±20% SPM3012T-1R0M 1.5 ±20% SPM3012T-1R5M 2.2 ±20% SPM3012T-2R2M 3.3 ±20% SPM3012T-3R3M 4.7 ±20% SPM3012T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
7 (7/49) SPM series SPM3012 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 20.0 Inductance (μh) R3M 5.0 2R2M 1R5M 1R0M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
8 (8/49) SPM series SPM3012 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4 4R7M Inductance (μh) R3M 2R2M 1R5M 1R0M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
9 (9/49) SPM series SPM3015 Type SHAPE & DIMENSIONS 3.2± ±0.1 (1.5) 0.85± ± ± max. 1.5±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
10 (10/49) SPM series SPM3015 Type CHARACTERISTICS SPECIFICATION TABLE L L measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM3015T-R47M 1.0 ±20% SPM3015T-1R0M 1.5 ±20% SPM3015T-1R5M 2.2 ±20% SPM3015T-2R2M 3.3 ±20% SPM3015T-3R3M 4.7 ±20% SPM3015T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
11 (11/49) SPM series SPM3015 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 20.0 Inductance (μh) R3M 2R2M 5.0 R47M Frequency (MHz) 1R5M 1R0M Product No. Manufacturer 4294A Agilent Technologies
12 (12/49) SPM series SPM3015 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4R7M 4 Inductance (μh) R3M 2R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
13 (13/49) SPM series SPM3020 Type SHAPE & DIMENSIONS 3.2± ±0.1 (1.5) 0.85± ± ± max. 1.5±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
14 (14/49) SPM series SPM3020 Type CHARACTERISTICS SPECIFICATION TABLE L L measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM3020T-R47M 1.0 ±20% SPM3020T-1R0M 1.5 ±20% SPM3020T-1R5M 2.2 ±20% SPM3020T-2R2M 3.3 ±20% SPM3020T-3R3M 4.7 ±20% SPM3020T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
15 (15/49) SPM series SPM3020 Type L FREQUENCY CHARACTERISTICS GRAPH R7M Inductance (μh) R3M 2R2M 5.0 1R5M R47M Frequency (MHz) 1R0M Product No. Manufacturer 4294A Agilent Technologies
16 (16/49) SPM series SPM3020 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4R7M 4 Inductance (μh) R3M 2R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
17 (17/49) SPM series SPM4012 Type SHAPE & DIMENSIONS 4.4± ±0.1 (2.6) 0.9± ± max. 4.1± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
18 (18/49) SPM series SPM4012 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM4012T-R47M 1.00 ±20% SPM4012T-1R0M 1.50 ±20% SPM4012T-1R5M 2.20 ±20% SPM4012T-2R2M 3.30 ±20% SPM4012T-3R3M 4.70 ±20% SPM4012T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
19 (19/49) SPM series SPM4012 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 15.0 Inductance (μh) R3M 2R2M 5.0 1R5M 1R0M R47M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
20 (20/49) SPM series SPM4012 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4 4R7M 3R3M Inductance (μh) R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
21 (21/49) SPM series SPM4015 Type SHAPE & DIMENSIONS 4.4± ±0.1 (2.6) 0.9± ± max. 4.1± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
22 (22/49) SPM series SPM4015 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM4015T-R47M 1.0 ±20% SPM4015T-1R0M 1.5 ±20% SPM4015T-1R5M 2.2 ±20% SPM4015T-2R2M 3.3 ±20% SPM4015T-3R3M 4.7 ±20% SPM4015T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
23 (23/49) SPM series SPM4015 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 25.0 Inductance (μh) R47M Frequency (MHz) 3R3M 2R2M 1R5M 1R0M Product No. Manufacturer 4294A Agilent Technologies
24 (24/49) SPM series SPM4015 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 6 5 4R7M Inductance (μh) R3M 2R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
25 (25/49) SPM series SPM4020 Type SHAPE & DIMENSIONS 4.4± ±0.1 (2.6) 0.9± ± max. 4.1± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
26 (26/49) SPM series SPM4020 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM4020T-R47M 1.0 ±20% SPM4020T-1R0M 1.5 ±20% SPM4020T-1R5M 2.2 ±20% SPM4020T-2R2M 3.3 ±20% SPM4020T-3R3M 4.7 ±20% SPM4020T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
27 (27/49) SPM series SPM4020 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 25.0 Inductance (μh) R3M 2R2M 1R5M 1R0M R47M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
28 (28/49) SPM series SPM4020 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4R7M 4 Inductance (μh) R3M 2R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
29 (29/49) SPM series SPM5012 Type SHAPE & DIMENSIONS 5.4± ±0.1 (3.0) 1.2± max. 5.1± ± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
30 (30/49) SPM series SPM5012 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM5012T-1R0M 2.20 ±20% SPM5012T-2R2M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
31 (31/49) SPM series SPM5012 Type L FREQUENCY CHARACTERISTICS GRAPH Inductance (μh) 4.0 2R2M 2.0 1R0M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
32 (32/49) SPM series SPM5012 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH R2M Inductance (μh) R0M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
33 (33/49) SPM series SPM5015 Type SHAPE & DIMENSIONS 5.4± ±0.1 (3.0) 1.2± max. 5.1± ± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
34 (34/49) SPM series SPM5015 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc ±20% SPM5015T-R47M 1.0 ±20% SPM5015T-1R0M 1.5 ±20% SPM5015T-1R5M 2.2 ±20% SPM5015T-2R2M 3.3 ±20% SPM5015T-3R3M 4.7 ±20% SPM5015T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
35 (35/49) SPM series SPM5015 Type L FREQUENCY CHARACTERISTICS GRAPH R7M Inductance (μh) R3M Frequency (MHz) 2R2M 1R5M 1R0M R47M Product No. Manufacturer 4294A Agilent Technologies
36 (36/49) SPM series SPM5015 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4R7M 4 3R3M Inductance (μh) R2M 1R5M 1R0M R47M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
37 (37/49) SPM series SPM5020 Type SHAPE & DIMENSIONS 5.4± ±0.1 (3.0) 1.2± max. 5.1± ± ±0.1 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
38 (38/49) SPM series SPM5020 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) max. typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc1 Idc2 1.0 ±20% SPM5020T-1R0M 1.5 ±20% SPM5020T-1R5M 2.2 ±20% SPM5020T-2R2M 3.3 ±20% SPM5020T-3R3M 4.7 ±20% SPM5020T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
39 (39/49) SPM series SPM5020 Type L FREQUENCY CHARACTERISTICS GRAPH R7M 25.0 Inductance (μh) R3M 2R2M 5.0 1R5M 1R0M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
40 (40/49) SPM series SPM5020 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 5 4 4R7M 3R3M Inductance (μh) 3 2 2R2M 1R5M 1 1R0M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
41 (41/49) SPM series SPM5030 Type SHAPE & DIMENSIONS 5.2± ±0.2 (2.9) 1.15±0.2 R20 5.0± ± max. 2.0±0.2 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
42 (42/49) SPM series SPM5030 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc ±20% SPM5030T-R20M 0.35 ±20% SPM5030T-R35M 0.75 ±20% SPM5030T-R75M 1.0 ±20% SPM5030T-1R0M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (20% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
43 (43/49) SPM series SPM5030 Type L FREQUENCY CHARACTERISTICS GRAPH Inductance (μh) 1.0 1R0M R70M 0.5 R35M R20M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
44 (44/49) SPM series SPM5030 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH R0M Inductance (μh) R75M R35M 0.2 R20M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
45 (45/49) SPM series SPM6530 Type SHAPE & DIMENSIONS 7.1± ±0.3 (3.8) 1.55±0.3 R25 6.5± ± max. 3.2±0.3 Dimensions in mm RECOMMENDED LAND PATTERN Dimensions in mm
46 (46/49) SPM series SPM6530 Type CHARACTERISTICS SPECIFICATION TABLE L Measuring DC resistance Rated current(a) frequency (m ) typ. Part No. (μh) Tolerance (khz) max. typ. Idc1 Idc ±20% SPM6530T-R25M ±20% SPM6530T-R47M ±20% SPM6530T-R68M ±20% SPM6530T-1R0M ±20% SPM6530T-1R5M ±20% SPM6530T-2R2M 3.3 ±20% SPM6530T-3R3M 4.7 ±20% SPM6530T-4R7M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (20% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40 C by self heating) The cleaning agent can not be used for these products. Measurement item Product No. Manufacturer L 4284A Agilent Technologies DC resistance AX-111A ADEX Rated current Idc1 4284A+42841A+42842C Agilent Technologies
47 (47/49) SPM series SPM6530 Type L FREQUENCY CHARACTERISTICS GRAPH R7M Inductance (μh) R25M R47M 5.0 3R3M 2R2M 1R5M 1R0M R68M Frequency (MHz) Product No. Manufacturer 4294A Agilent Technologies
48 (48/49) SPM series SPM6530 Type INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH R7M Inductance (μh) R3M R2M 2.0 1R5M 1.5 1R0M 1.0 R68M 0.5 R47M R25M DC current (A) Product No. Manufacturer 4284A+42841A+42842C Agilent Technologies
49 (49/49) SPM series Packaging Style REEL DIMENSIONS 2.0±0.5 E (1.0) N Type A W1 W2 N E SPM3012 ø ø SPM3015 ø ø SPM3020 ø ø SPM4012 ø ø SPM4015 ø ø SPM4020 ø ø SPM5012 ø ø SPM5015 ø ø SPM5020 ø ø SPM5030 ø ø SPM6530 ø ø A ø13.0±0.5 ø21.0±0.8 W1 W2 * These values are typical values. Dimensions in mm TAPE DIMENSIONS ød0 P2 P0 P1 K W B F E A t Dimensions in mm Type A B ød0 E F P0 P1 P2 W K t SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ± SPM / ± ± ± ± ± ±
50 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: SPM6530T-1R0M120 SPM6530T-1R5M100 SPM6530T-R47M170 SPM6530T-R68M140 SPM5030T-1R0MT SPM4012T-3R3M T SPM5012T-1R0MT SPM4012T-1R5M T SPM5012T-2R2MT SPM4012T-4R7MT SPM4012T- 2R2M T SPM4012T-1R0M T SPM4012T-R47M T
January 2015. Inductors for Power Circuits. Wound Ferrite. VLCF Series. VLCF5028-2 Type VLCF5028-2
January 2015 Inductors for Power Circuits Wound Ferrite VLCF Series VLCF5028-2 (2/9) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY
February 2015. Chip Beads. For power line. HF-ACC Series. HFxxACC3216. * Dimensions Code JIS[EIA]
![February 2015. Chip Beads. For power line. HF-ACC Series. HFxxACC3216. * Dimensions Code JIS[EIA]](/thumbs/19/266676.jpg "February 2015. Chip Beads. For power line. HF-ACC Series. HFxxACC3216. * Dimensions Code JIS[EIA]")
E M C C o m p o n e n t s February 2015 Chip Beads For power line HF-ACC Series HFxxACC3216 [1206 inch]* * Dimensions Code JIS[EIA] (2/8) REMINDERS FOR USING THESE PRODUCTS Before using these products,
November 2013. 3-terminal Filters. For signal line. MEM series. * Dimensions Code JIS[EIA]
![November 2013. 3-terminal Filters. For signal line. MEM series. * Dimensions Code JIS[EIA]](/thumbs/29/13476958.jpg "November 2013. 3-terminal Filters. For signal line. MEM series. * Dimensions Code JIS[EIA]")
E M C C o m p o n e n t s November 0 -terminal Filters For signal line MEM series MEM0S MEM0SC MEM0V MEM0F MEM608P 0[0805 inch]* 0[0805 inch] 0[0805 inch] 0[0805 inch] 608[060 inch] * Dimensions Code JIS[EIA]
June 2016. Magnetic Sheets for RFID. Flexield. IFL/IBF series
M A G N E T I C S H E E T June 2016 Magnetic Sheets for RFID Flexield IFL/IBF series (2/8) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications.
PCMC063T- Power Choke Coil
PCMC063T- Power Choke Coil Features Low loss realized with low DCR 100% lead (Pb) free, RoHS compliant High performance (Isat) realized by metal dust core Low profile: 12.6mm x 13.8mm x 5.0mm Capable of
WE-PD SMD Shielded Power Inductor
A Dimensions: [mm] B Recommended land pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Inductance 1 khz/ 250 mv L 100 µh ±20% Rated current T = 40 K I R 2.5 A max. Saturation
SPECIFICATION MARITEX 06/30/ 08 CHIP INDUCTORS (ROHS)
FL201209SERIESLFR FL201209SERIESLFR Scope: This specification applies to multilayer ferrite & ceramicchip inductors. 1. Part Number Key & Mechanical Drawing FL XX XX XX XXX X A B C Tolerance Inductance
WE-GFH High Frequency SMD Inductor
A Dimensions: [mm] B Recommended land pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Inductance 1.92 MHz L 100 µh ± 10% Rated current T = 40 K I R 160 ma max. DC Resistance
For high-speed differential signal line/general signal line
Common Mode Filters For high-speed differential signal line/general signal line ACM series Type: ACM0 ACM0 ACM ACM [080 inch]* [008 inch] [0 inch] [8 inch] * Dimensions Code [EIA] Issue date: September
Chip NTC Thermistor for temperature sensor and temperature compensation 0201 size
P 1 / 8 Chip NTC Thermistor for temperature sensor and temperature compensation 0201 size 1. Part Numbering (ex.) NC P 03 XH 103 F 05 RL Product ID Series Dimensions Temperature Resistance Resistance Individual
MADP-000504-10720T. Non Magnetic MELF PIN Diode
MADP-54-172T Features High Power Handling Low Loss / Low Distortion Leadless Low Inductance MELF Package Non-Magnetic Surface Mountable RoHS Compliant MSL 1 Package Style 172 Dot Denotes Cathode Description
MAPD-007530-0001TB. Low Cost Two-Way GMIC SMT Power Divider 1700 2000 MHz Rev. V2. Features. Functional Diagram. Description. Ordering Information
Features Small Size and Low Profile Typical Insertion Loss: 0.6 db Typical Amplitude Balance: 0.2 db 1 Watt Power Handling Lead-Free SOT-26 Package 100% Matte Tin Plating over Copper Halogen-Free Green
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
Types MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
0.45mm Height 0402 Package Pure Green Chip LED Technical Data Sheet. Part No.: LL-S160PGC-G5-1B
.45mm Height 42 Package Pure Green Chip LED Technical Data Sheet Part No.: LL-S16PGC-G5-1B Spec No.: S16 Rev No.: V.2 Date: Dec./6/25 Page: 1 OF 9 Features: Package in 8mm tape on 7" diameter reel. Compatible
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
4N25 Phototransistor Optocoupler General Purpose Type
4N Phototransistor Optocoupler General Purpose Type Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The 4N is an
NARROW-PITCH (0.8mm) CONNECTORS P8 SERIES
Socket Header Compliance with RoHS Directive NRROW-PITCH CONNECTORS FOR PC ORDS 3. Perfect for portable devices, the bellows-type provide a strong resistance against falling, impacts, and forced insertions
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
B Recommended land pattern: [mm] SSt. SSt 2014-07-15 2014-05-12. SSt. SSt. SSt 2014-01-07. SSt 2013-11-19. SSt. SBa. SSt 2013-04-24.
![B Recommended land pattern: [mm] SSt. SSt 2014-07-15 2014-05-12. SSt. SSt. SSt 2014-01-07. SSt 2013-11-19. SSt. SBa. SSt 2013-04-24.](/thumbs/17/124841.jpg "B Recommended land pattern: [mm] SSt. SSt 2014-07-15 2014-05-12. SSt. SSt. SSt 2014-01-07. SSt 2013-11-19. SSt. SBa. SSt 2013-04-24.")
A Dimensions: [mm] B Recommended land pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Inductance 1 khz/ 100 mv L 2x 51 µh ±30% Impedance Z max 5500 Ω typ. Rated current
WCAP-CSGP Ceramic Capacitors
A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1±0.2 Vrms, 1 khz ±10% C 15000 pf ± 10% Rated voltage Dissipation factor
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
Contents. 12. Lot Number 10. 13. Reel Packing Structure 11. 14. Precaution for Use 13. 15. Hazard Substance Analysis 14. 16. Revision History 18
Rev : 00 ISSUE NO : DATE OF ISSUE : 2009. 04. 10 S P E C I F I CATION MODEL : SLHNNWW629T1S0U0S0 [Rank : (S0), (U0), (S0)] HIGH POWER LED - SUNNIX6 CUSTOMER : CUSTOMER CHECKED CHECKED APPROVED SAMSUNG
WE-FAMI THT Power Inductor
A Dimensions: [mm] B Recommended land pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Inductance 100 khz/ 1 V L 22 µh ±20% Rated current T = 40 K I R 4.1 A max. Saturation
Product code Style Construction Inductance Packaging. Core. Core Terminal. Case. D Omission. Terminal Core. Terminal board
Choke Coils Series : Pin terminal Type : 09D, 11D, 12D, 16B, 18B, E, 12E, 15E, 18E Type 09D Type 11D Type 12D Pin terminal inductors featuring small size and high performance Features High - µ and High
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
HP1, HPH1 HP2, HPH2 HP3, HPH3 HP4, HPH4 HP5, HPH5 HP6, HPH6. Winding Layouts. One 6-filar winding
Document 63- HP, HPH HP, HPH HP3, HPH3 HP4, HPH4 HP5, HPH5 HP6, HPH6 Six : isolated windings that can be connected in series or parallel Tightly coupled windings 500 Vrms, one minute isolation between
MAAD-007084-0001TB. Digital Attenuator 15.5 db, 5-Bit, TTL Driver, DC-2.0 GHz Rev. V2. Features. Schematic with Off-Chip Components.
MAAD-007084-00000 5.5, 5-Bit, TTL Driver, DC-2.0 GHz Rev. 2 Features Attenuation: 0.5 Steps to 5.5 Low DC Power Consumption Integral TTL Driver 50 ohm Impedance Test Boards are Available Tape and Reel
Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description
MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
WE-CBF SMD EMI Suppression Ferrite Bead
A Dimensions: [mm] B Recommended land pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Impedance @ 100 MHz 100 MHz Z 600 Ω ±25% Maximum impedance 80 MHz Z 650 Ω typ. Rated
Gas Discharge Tube (GDT) Products CG5 and SL0902A Series. CG5 and SL0902A Series
Description Agency Approvals AGENCY AGENCY FILE NUMBER E128662 2 Electrode GDT Graphical Symbol Littelfuse Broadband Optimized SL0902A Series offers high surge ratings in a miniature package. Special design
Power Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet 0603 Package Chip LED (0.8 mm Height) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
1.50mm Height 2220 Package Top View Full Color Chip LEDs Technical Data Sheet. Part No.: LL-R5050RGBC-001
.5mm Height 222 Package Top View Full Color Chip LEDs Technical Data Sheet Part No.: LL-R55RGBC- Spec No.: R55 Rev No.: V.2 Date: Mar./6/26 Page: OF 2 Features: P-LCC-6 package. White package. Optical
Product Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
Features. Typical Applications G9. ProLight PEA2-3FVE 3W Warm White AC LED Technical Datasheet Version: 1.7 1 DS-0042
ProLight PEA2-3FVE 3W Warm White AC LED Technical Datasheet Version: 1.7 Features High Color rendering index Follow ANSI C78.788.2008 Chromaticity co-ordinates High flux per LED Good color uniformity Industry
USB3.0 Micro-B Connector
USB3.0 Micro-B Connector ZX360 Series General The ZX360 Series is a Micro-USB connector that is compliant with the MicroUSB 3.0 specifications and supports up to 5Gbps high speed data transmission. As
WE-LF SMD Common Mode Power Line Choke
A Dimensions: [mm] B Recommended hole pattern: [mm] D Electrical Properties: Properties Test conditions Value Unit Tol. Inductance 10 khz/ 0.1 ma L 2x 6.8 mh ±30% Rated current @ 70 C I R 1.0 A max. DC
Data Sheet, V1.1, May 2008 SMM310. Silicon MEMS Microphone. Small Signal Discretes
Data Sheet, V1.1, May 2008 SMM310 Small Signal Discretes Edition 2008-05-28 Published by Infineon Technologies AG 81726 München, Germany Infineon Technologies AG 2008. All Rights Reserved. Legal Disclaimer
EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet Chip LED with Bi-Color (Multi-Color) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
SELECTION GUIDE. Nominal Input
www.murata-ps.com NKE Series FEATURES RoHS Compliant Sub-Miniature SIP & DIP Styles 3kVDC Isolation UL Recognised Wide Temperature performance at full 1 Watt load, 40 C to 85 C Increased Power Density
CMS Common mode inductors, surface mount
Technical Data 4313 Effective October 215 Supersedes March 27 Common mode inductors, surface mount pplications EMI filters DC-DC brick power supplies Discrete output supplies Discrete and point-of-use
Ultra low ohmic Metal plate / High power type Shunt Resistors
Ultra low ohmic Metal plate / High power type Shunt Resistors PSR Series Features 1) High power class up to 4 to 5W. 2) The lineup of ultra-low resistance value : correspondence from 0.2m 3) Excellent
703-0148 InGaN / Sapphire White Water clear. Parameter Rating Unit
Package Dimensions: * All dimensions are in mm * Tolerance: ±.6mm unless otherwise noted. LED Chip Lens Colour Ant Part No. Material Colour Coordinates 73-148 InGaN / Sapphire White Water clear Absolute
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
SURFACE MOUNT LED LAMP STANDARD BRIGHT 0606
PACKAGE DIMENSIONS 0.075 (1.9) 0.063 (1.6) 0.035 (0.9) TOP 0.047 (1.2) 0.012 (0.3) 0.032 [0.8] SIDE 0.043 [1.1] 1 3 0.020 [0.5] 2 4 BOTTOM CATHODE MASK 1 2 3 4 HER / AlGaAs Red / Yellow (for-34) Green
NTCG series. NTC Thermistors SMD. Temperature Protection Devices. 0603 [0201 inch]* 1005 [0402 inch] 1608 [0603 inch] 2012 [0805 inch] September 2015
![NTCG series. NTC Thermistors SMD. Temperature Protection Devices. 0603 [0201 inch]* 1005 [0402 inch] 1608 [0603 inch] 2012 [0805 inch] September 2015](/thumbs/40/21620016.jpg "NTCG series. NTC Thermistors SMD. Temperature Protection Devices. 0603 [0201 inch]* 1005 [0402 inch] 1608 [0603 inch] 2012 [0805 inch] September 2015")
September 2015 NTC Thermistors SMD NTCG series NTCG06 NTCG10 NTCG16 NTCG20 0603 [0201 inch]* 1005 [0402 inch] 1608 [0603 inch] 2012 [0805 inch] * Dimensions Code JIS[EIA] (2/27) REMINDERS FOR USING THESE
Type EDL, Electric Double Layer Supercapacitors Ultra High Capacitance, Small Case Size Options
Ultra High Capacitance, Small Case Size Options Type EDL electric double layer supercapacitors offer extremely high capacitance values (farads) in a variety of packaging options that will satisfy, low
Data Sheet. HLMP-4700, HLMP-4719, HLMP-4740 HLMP-1700, HLMP-1719, HLMP-1790 T-1 3 / 4 (5 mm), T-1 (3 mm), Low Current LED Lamps. Description.
HLMP-4700, HLMP-4719, HLMP-4740 HLMP-1700, HLMP-1719, HLMP-1790 T-1 3 / 4 (5 mm), T-1 (3 mm), Low Current LED Lamps Data Sheet Description These tinted diffused LED lamps are designed and optimized specifically
Ceramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
CLA4607-085LF: Surface Mount Limiter Diode
DATA SHEET CLA4607-085LF: Surface Mount Limiter Diode Applications Low-loss, high-power limiters Receiver protectors Anode (Pin 1) Anode (Pin 3) Features Low thermal resistance: 55 C/W Typical threshold
3. Terminal Shape P : PCB terminals FS: Surface-mounting terminals, short FL : Surface-mounting terminals, long
Surfacemounting Relay Ultracompact and Slim DPDT Relay Suitable for highdensity mounting.(.7 mm (W). mm (L) 9 mm (H)). Dielectric strength of, VAC and an impulse withstand voltage of 2, V for 2 μs (conforms
3mm Photodiode,T-1 PD204-6C/L3
3mm Photodiode,T-1 Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high
For board-to-fpc. Narrow Pitch Connectors (0.35mm pitch)
For board-to-fpc Narrow Pitch Connectors (0.35mm pitch) S35 Series New FEATURES 1. 1.7 mm wide slim two-piece type connector Mated height 0.6 mm Smaller compared to A4F series Width: Approx. 44% down
SMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
Broadband covering primary wireless communications bands: Cellular, PCS, LTE, WiMAX
High Gain, High IP3 Monolithic Amplifier 50Ω 0.01 to 6 GHz The Big Deal High Gain Broadband High Dynamic Range without external Matching Components May be used as a replacement to RFMD SBB5089Z a,b SOT-89
General information. Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news.
DC Film Capacitors Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news. Contents Pitch Rated Voltage Capacitance Page mm Vdc range range
DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
Spezifikation für Freigabe / specification for release
Artikelnummer / part number : 82380050100 Datum / Date : 2006-08-01 ROHS Compliant A Mechanische Abmessungen / dimensions : b SIZ Size L T a b min/max min/max min/max min/max 0508 1.05/1.35 1.85 /2.15
Power Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
INTEGRATED CIRCUITS DATA SHEET. TDA7052 1 W BTL mono audio amplifier. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET TDA7052 1 W BTL mono audio amplifier File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The TDA7052 is a mono output amplifier in a 8-lead dual-in-line (DIL)
Data Sheets of AVA Technology SMD Type White LED. Model : T5050. AVA Technology Co.
Data Sheets of AVA Technology SMD Type White LED Model : AVA Technology Co. 2640 S. Myrtle Ave. Suite 6 Monrovia, CA 91016 P: 626-574-7726 F: 626-574-7732 http://www.led4light.com Top View LED with Reflector
SMT inductors. SIMID series, SIMID 1812-A. Date: March 2008
SMT inductors SIMID series, Series/Type: Data Sheet Date: March 2008 EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein
DATA SHEET. TDA1543 Dual 16-bit DAC (economy version) (I 2 S input format) INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 February 1991 FEATURES Low distortion 16-bit dynamic range 4 oversampling possible Single 5 V power supply No external components required
Cree PLCC6 3 in 1 SMD LED SLV6A-FKB
Cree PLCC6 3 in 1 SMD LED PRODUCT FAMILY DATA SHEET CLD-CT1320.001 PRODUCT DESCRIPTION These SMD LEDs are packaged in an industry standard PLCC6 package. These high performance tricolor SMT LEDs are designed
Komatsulite NR Series Breaker (Thermal Cutoff Device)
*RoHS COMPLIANT & **HALOGEN FREE Ratings 6 7 5 1 1 1 5 5 C N R 7 2 A B 0 1 2 1 5 C N R 7 7 C B 0 *RoHS COMPLIANT Features n Miniature Thermal Cutoff (TCO) device n Smallest body size, high current type
DISCONTINUED (1998) FBR46 SERIES. MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment.
Spezifikation für Freigabe / specification for release
Artikelnummer / part number : 82550350 Datum / Date : 31.07.06 description : 0805 SMD VARISTOR Lead Free SMD size: 0805 ROHS Compliant A Mechanische Abmessungen / dimensions : SIZE SIZE W L T a 0402 0.5
Features. Applications. Truth Table. Close
ASSR-8, ASSR-9 and ASSR-8 Form A, Solid State Relay (Photo MOSFET) (0V/0.A/0Ω) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically
AP1509. 150KHz, 2A PWM BUCK DC/DC CONVERTER. Description. Pin Assignments V IN. Applications. Features. (Top View) GND GND. Output AP1509 GND GND
Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 2A load without additional transistor. It saves board space. The external
VT-802 Temperature Compensated Crystal Oscillator
T-802 Temperature Compensated Crystal Oscillator T-802 Description ectron s T-802 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, CMOS output, analog temperature compensated oscillator,
0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors
0.9 0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors FH43B Series Space saving 17.8mm(81 pos. shown) 2.77 Can be mounted over conductive traces. Features 1. Low-profile, small
S112-XHS. Description. Features. Agency Approvals. Applications. Absolute Maximum Ratings. Schematic Diagram. Ordering Information
Description Features The S112-X is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. The circuit is composed of one input IR LED with a series limiting resistor
INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
SPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
HL-A-3528H308W-S1-13. Description. Applications. Recommended Soldering. Package Dimensions
RoHS Specification Client Name: Client P/N: Factory P/N: HL-A-3528H308W-S1-13 OF-SMD3528WN Sending Date: Client approval Hong li approval Approval Audit Confirmation Approval Audit Confirmation 殷 小 平 王
3W RGB High Power LED
Features: Super high flux output and high luminance Designed for high current operation Low thermal resistance No UV Package Dimensions: Typical Applications Reading lights Portable flashlight Uplighters
TLRK1100C(T11), TLRMK1100C(T11), TLSK1100C(T11), TLOK1100C(T11), TLYK1100C(T11)
TOSHIBA LED Lamps TL(RK,RMK,SK,OK,YK)C(T) TLRKC(T), TLRMKC(T), TLSKC(T), TLOKC(T), TLYKC(T) Panel Circuit Indicators Unit: mm Surface-mount devices.2 (L) mm 2.8 (W) mm.9 (H) mm Flat-top type InGaAlP LEDs
FXU P C 5 1 5 R 156.25 Frequency (in MHz) Resolutions to 6 places past the decimal point 1 = 1.8V 2 = 2.5 V 3 = 3.3 V
LVPECL 5 x 3.2mm 1.8V Oscillator Features Model: FXU-PC51 SERIES Freq: 0.016 MHz to 670 MHz Rev. 05/27/2015 ULTRA Low Jitter Low Cost XPRESS Delivery Frequency Resolution to six decimal places Stabilities
PCC-M0854M (MC) PCC-M0850M (MC) PCC-M1054M (MC) PCC-M1050M (MC) PCC-M1050ML (MC) PCC-M1060ML (MC)
Power Choke Coil for Automotive application : PCC-M7M (MC) PCC-M8M (MC) PCC-M8M (MC) PCC-M1M (MC) PCC-M1M (MC) PCC-M1ML (MC) PCC-M16ML (MC) M7M M8M M8M M1M M1M M1ML M16ML Realize high heat resistance and
MASW-007070-0001TB. GaAs SPST Switch, Absorptive, Single Supply, DC-4.0 GHz. Features. Pin Configuration 1,2,3,4. Description. Ordering Information
Features Operates DC - 4 GHz on Single Supply ASIC TTL / CMOS Driver Low DC Power Consumption 50 Ohm Nominal Impedance Test Boards are Available Tape and Reel are Available Lead-Free 4 x 6 mm PQFN Package
DSL03. Low capacitance TVS for high speed lines such as xdsl. Description. Features. Complies with the following standards
Low capacitance TVS for high speed lines such as xdsl Description Datasheet - production data Features High surge capability to comply with GR-1089 and ITU-T K20/21 Keeps its peak power capability up to
1.0A LOW DROPOUT LINEAR REGULATOR
1.0A LOW DROPOUT LINEAR REGULATOR Description Pin Assignments The is a low dropout three-terminal regulator with 1.0A output current ability, and the dropout voltage is specified at typical 1.1V at 1.0A
Suntan Technology Company Limited. Application Guidelines For Tantalum Electroilytic Capacitors
For obtaining the most stable quality and sufficient Performance of the tantalum electrolytic capacitors,appropriate use must be made.before use,confirm the use conditions and rating performance of the
P O W E R C A P A C I T O R A S S E M B L I E S
AMERICAN TECHNICAL CERAMICS P O W E R C A P A C I T O R A S S E M B L I E S ISO 9001 REGISTERED COMPANY Overview About ATC Power Assemblies ATC standard & custom Power Assemblies are fabricated from PARALLEL
SPI-8001TW. Switching Regulators. Dual 1.5 A, DC/DC Step-Down Converter. SANKEN ELECTRIC CO., LTD. http://www.sanken-ele.co.jp/en/
Data Sheet 27469.301.1 Designed to meet high-current requirements at high efficiency in industrial and consumer applications; embedded core, memory, or logic supplies; TVs, VCRs, and office equipment,
Applications SS 26 V- R 05 1170
AC Line Filters SS Coils, SS2V Type Overview The KEMET SS Coils, SS2V Type AC line filters are offered in a wide variety of sizes and specifications. Applications Consumer Electronics Common mode choke
SMD Aluminum Solid Capacitors with Conductive Polymer
SMD Aluminum Solid Capacitors with Conductive Polymer FEATURES New OS-CON series provides improved characteristics with up to 25 C temperature capability and 35 V maximum voltage rating in a SMD package
EE-SX91. Meeting Customer Needs with Compact Sensors that Mount with M3 Screws
Compact Pre-wired Photomicrosensor with Built-in Amplifier (Non-modulated) CSM DS_E_7_2 Meeting Customer Needs with Compact Sensors that Mount with M Screws Both light-on and dark-on outputs provided.
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
Type RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
ONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD. FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.
ONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD SWITCHES FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.2g) Solder terminal type with mounting holes (0.3g)
SPEC NO: DSAJ8637 REV NO: V.6B DATE: JUL/01/2016 PAGE: 1 OF 5 APPROVED:
1.0X0.5mm SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APHHS1005ZGC Green Features 1.0mmX0.5mm SMD LED, 0.5mm thickness. Low power
TPN4R712MD TPN4R712MD. 1. Applications. 2. Features. 3. Packaging and Internal Circuit. 2014-12 2015-04-21 Rev.4.0. Silicon P-Channel MOS (U-MOS )
MOSFETs Silicon P-Channel MOS (U-MOS) TPN4R712MD TPN4R712MD 1. Applications Lithium-Ion Secondary Batteries Power Management Switches 2. Features (1) Low drain-source on-resistance: R DS(ON) = 3.8 mω (typ.)
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS RL-High power series 5%, 2%, 1% sizes 0805/1206
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS series 5%, 2%, 1% sizes 005/1206 RoHS compliant Product specification Aug 27, 200 V.2 Product specification 2 SCOPE This specification describes RL005/1206
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip