High Power Thick Film Chip Resistor 2512
|
|
|
- Leslie Barnett
- 7 years ago
- Views:
Transcription
1 Specifications: Type : MCHP12 Power Rating at 70 C : 2W Working Voltage : 250V Max. Overload Voltage : 500V Max. Dielectric Withstanding Voltage : 500V Temperature Range : -55 C to +155 C Ambient Temperature : 70 C Nominal Resistance : 10Ω Power Rating: Resistors shall have a power rating based on continuous load operation at an ambient temperature of C 70 C. For temperature in excess of 70 C, The load shall be derate as shown in figure. Nominal Resistance: Effective figures of nominal resistance shall be in accordance with E-96 series E-96 series for 1%. Page <1> 21/05/14 V1.0
2 Construction: Dimensions: Type L ±0.1 W ±0.15 H ±0.1 l1 ±0.25 l2 ±0.2 MCHP12 () Dimensions : Millimetres Page <2> 21/05/14 V1.0
3 Performance specification: Characteristics Limits Test Methods ( JIS C ) Dielectric withstanding voltage Temperature Coefficient Short time overload No evidence of flashover mechanical damage, arcing or insulation break down 1Ω~10Ω ± 200PPM/ C 11Ω~10MΩ ± 100PPM/ C ±1% (1% + 0.1Ω) Max. Clamped in the trough of a 90 C metallic v-block and shall be tested at ac potential respectively specified in the type for seconds Natural resistance change per temp. degree centigrade. R2-R1 R1(t2-t1) 106 (PPM/ C) R1: Resistance value at room temperature (T1) R2: Resistance value at room temp. plus 100 C(T2) Test pattern: room temp. (T1), room temp C(T2) Permanent resistance change after the application of a potential of 2.5 times RCWV for 5 seconds Wave Solder: Test temperature of solder: 245 C ±3 C dipping time in solder: 2-3 seconds. Refolw: Solderability 95% coverage Min. Soldering heat : ±(1%+0.05Ω) Max. Dip the resistor into a solder bath having a temperature of 260 C±3 C and hold it for 10±1 seconds. Resistance change after continuous 5 cycles for duty cycle specified below: Temperature cycling ±1% (0.5% Ω) Max. Temperature -55 C ± 3 C Room temp C ± 2 C Room temp. Time 30 mins 10 to 15 mins 30 mins 10 to15 mins Page <3> 21/05/14 V1.0
4 Humidity Characteristics Limits Test Methods ( JIS C ) Load life in humidity Load Life Terminal bending ±1% (0.5% + 0.1Ω) Max. ±1% (1% + 0.1Ω) Max. ±1% (1% + 0.1Ω) Max. ±(1% Ω) Max. Temporary resistance change after 240 hours exposure in a humidity test chamber controlled at 40±2 C and 90-95% relative humidity Resistance change after 1,000 hours (1.5 hours on, 0.5 hour off ) at RCWV in a humidity chamber controlled at 40 C ± 2 C and 90 to 95% relative humidity Permanent resistance change after 1,000 hours operating at RCWV, with duty cycle of (1.5 hours on, 0.5 hour off ) at 70 C ± 2 C ambient Twist of Test Board : Y/X = 3/90mm for 60 seconds Packing specification: Type A ±0.2 B ±0.2 C ±0.05 ØD E ±0.10 F ±0.05 G ±0.1 W ±0.20 ØD T ± 0.1 MCHP12 () Dimensions : Millimetres Type Quantity Per Reel A ± 0.5 B ± 0.5 C ± 0.5 D ± 1 M ± 2 W ±1 MCHP12 () 4,000 Pcs. Reel Remark: ΦM 10,000pcs. / Reel = 255 ± 2mm 20,000pcs. / Reel = 330 ± 2mm Page <4> 21/05/14 V1.0
5 Marking: A. Marking for E-96 series in size : 4 Digits *The first 3 digits are singnificant figures of resistance and the 4th digit denoted number of zeros. 100KΩ *For ohmic values below 100 Ω, letter"r" is for decimal point. 1.8Ω B. Marking for E-24 series in size : 3 Digits *The first 2 digits are singnificant figures of resistance and the 3rd digit denoted number of zeros. 1KΩ *For ohmic values below 10 Ω, letter"r" is for decimal point. 0.68Ω Page <5> 21/05/14 V1.0
6 Table Resistor, Thick Film, 10R, 2W, 1% MCHP122WF100JT4E Resistor, Thick Film, 430R, 2W, 1% MCHP122WF4300T4E Resistor, Thick Film, 11R, 2W, 1% MCHP122WF110JT4E Resistor, Thick Film, 470R, 2W, 1% MCHP122WF4700T4E Resistor, Thick Film, 12R, 2W, 1% MCHP122WF120JT4E Resistor, Thick Film, 510R, 2W, 1% MCHP122WF5100T4E Resistor, Thick Film, 13R, 2W, 1% MCHP122WF130JT4E Resistor, Thick Film, 620R, 2W, 1% MCHP122WF6200T4E Resistor, Thick Film, 15R, 2W, 1% MCHP122WF150JT4E Resistor, Thick Film, 680R, 2W, 1% MCHP122WF6800T4E Resistor, Thick Film, 16R, 2W, 1% MCHP122WF160JT4E Resistor, Thick Film, 750R, 2W, 1% MCHP122WF7500T4E Resistor, Thick Film, 18R, 2W, 1% MCHP122WF180JT4E Resistor, Thick Film, 820R, 2W, 1% MCHP122WF8200T4E Resistor, Thick Film, 20R, 2W, 1% MCHP122WF200JT4E Resistor, Thick Film, 910R, 2W, 1% MCHP122WF9100T4E Resistor, Thick Film, 22R, 2W, 1% MCHP122WF220JT4E Resistor, Thick Film, 1K, 2W, 1% MCHP122WF1001T4E Resistor, Thick Film, 24R, 2W, 1% MCHP122WF240JT4E Resistor, Thick Film, 1K1, 2W, 1% MCHP122WF1101T4E Resistor, Thick Film, 27R, 2W, 1% MCHP122WF270JT4E Resistor, Thick Film, 1K2, 2W, 1% MCHP122WF1201T4E Resistor, Thick Film, 30R, 2W, 1% MCHP122WF300JT4E Resistor, Thick Film, 1K3, 2W, 1% MCHP122WF1301T4E Resistor, Thick Film, 33R, 2W, 1% MCHP122WF330JT4E Resistor, Thick Film, 1K5, 2W, 1% MCHP122WF1501T4E Resistor, Thick Film, 36R, 2W, 1% MCHP122WF360JT4E Resistor, Thick Film, 1K6, 2W, 1% MCHP122WF1601T4E Resistor, Thick Film, 39R, 2W, 1% MCHP122WF390JT4E Resistor, Thick Film, 1K8, 2W, 1% MCHP122WF1801T4E Resistor, Thick Film, 43R, 2W, 1% MCHP122WF430JT4E Resistor, Thick Film, 2K, 2W, 1% MCHP122WF2001T4E Resistor, Thick Film, 47R, 2W, 1% MCHP122WF470JT4E Resistor, Thick Film, 2K7, 2W, 1% MCHP122WF2701T4E Resistor, Thick Film, 51R, 2W, 1% MCHP122WF510JT4E Resistor, Thick Film, 3K, 2W, 1% MCHP122WF3001T4E Resistor, Thick Film, 56R, 2W, 1% MCHP122WF560JT4E Resistor, Thick Film, 3K3, 2W, 1% MCHP122WF3301T4E Resistor, Thick Film, 62R, 2W, 1% MCHP122WF620JT4E Resistor, Thick Film, 3K6, 2W, 1% MCHP122WF3601T4E Resistor, Thick Film, 68R, 2W, 1% MCHP122WF680JT4E Resistor, Thick Film, 3K9, 2W, 1% MCHP122WF3901T4E Resistor, Thick Film, 75R, 2W, 1% MCHP122WF750JT4E Resistor, Thick Film, 4K3, 2W, 1% MCHP122WF4301T4E Resistor, Thick Film, 82R, 2W, 1% MCHP122WF820JT4E Resistor, Thick Film, 4K7, 2W, 1% MCHP122WF4701T4E Resistor, Thick Film, 91R, 2W, 1% MCHP122WF910JT4E Resistor, Thick Film, 5K1, 2W, 1% MCHP122WF5101T4E Resistor, Thick Film, 100R, 2W, 1% MCHP122WF1000T4E Resistor, Thick Film, 5K6, 2W, 1% MCHP122WF5601T4E Resistor, Thick Film, 110R, 2W, 1% MCHP122WF1100T4E Resistor, Thick Film, 6K2, 2W, 1% MCHP122WF6201T4E Resistor, Thick Film, 120R, 2W, 1% MCHP122WF1200T4E Resistor, Thick Film, 6K8, 2W, 1% MCHP122WF6801T4E Resistor, Thick Film, 130R, 2W, 1% MCHP122WF1300T4E Resistor, Thick Film, 7K5, 2W, 1% MCHP122WF7501T4E Resistor, Thick Film, 150R, 2W, 1% MCHP122WF1500T4E Resistor, Thick Film, 8K2, 2W, 1% MCHP122WF8201T4E Resistor, Thick Film, 160R, 2W, 1% MCHP122WF1600T4E Resistor, Thick Film, 9K1, 2W, 1% MCHP122WF9101T4E Resistor, Thick Film, 180R, 2W, 1% MCHP122WF1800T4E Resistor, Thick Film, 10K, 2W, 1% MCHP122WF1002T4E Resistor, Thick Film, 200R, 2W, 1% MCHP122WF2000T4E Resistor, Thick Film, 11K, 2W, 1% MCHP122WF1102T4E Resistor, Thick Film, 220R, 2W, 1% MCHP122WF2200T4E Resistor, Thick Film, 12K, 2W, 1% MCHP122WF1202T4E Resistor, Thick Film, 240R, 2W, 1% MCHP122WF2400T4E Resistor, Thick Film, 13K, 2W, 1% MCHP122WF1302T4E Resistor, Thick Film, 270R, 2W, 1% MCHP122WF2700T4E Resistor, Thick Film, 15K, 2W, 1% MCHP122WF1502T4E Resistor, Thick Film, 300R, 2W, 1% MCHP122WF3000T4E Resistor, Thick Film, 16K, 2W, 1% MCHP122WF1602T4E Resistor, Thick Film, 330R, 2W, 1% MCHP122WF3300T4E Resistor, Thick Film, 18K, 2W, 1% MCHP122WF1802T4E Resistor, Thick Film, 360R, 2W, 1% MCHP122WF3600T4E Resistor, Thick Film, 20K, 2W, 1% MCHP122WF2002T4E Resistor, Thick Film, 390R, 2W, 1% MCHP122WF3900T4E Resistor, Thick Film, 22K, 2W, 1% MCHP122WF2202T4E Page <6> 21/05/14 V1.0
7 Resistor, Thick Film, 24K, 2W, 1% MCHP122WF2402T4E Resistor, Thick Film, 180K, 2W, 1% MCHP122WF1803T4E Resistor, Thick Film, 27K, 2W, 1% MCHP122WF2702T4E Resistor, Thick Film, 200K, 2W, 1% MCHP122WF2003T4E Resistor, Thick Film, 33K, 2W, 1% MCHP122WF3302T4E Resistor, Thick Film, 220K, 2W, 1% MCHP122WF2203T4E Resistor, Thick Film, 39K, 2W, 1% MCHP122WF3902T4E Resistor, Thick Film, 240K, 2W, 1% MCHP122WF2403T4E Resistor, Thick Film, 43K, 2W, 1% MCHP122WF4302T4E Resistor, Thick Film, 300K, 2W, 1% MCHP122WF3003T4E Resistor, Thick Film, 47K, 2W, 1% MCHP122WF4702T4E Resistor, Thick Film, 330K, 2W, 1% MCHP122WF3303T4E Resistor, Thick Film, 51K, 2W, 1% MCHP122WF5102T4E Resistor, Thick Film, 360K, 2W, 1% MCHP122WF3603T4E Resistor, Thick Film, 56K, 2W, 1% MCHP122WF5602T4E Resistor, Thick Film, 390K, 2W, 1% MCHP122WF3903T4E Resistor, Thick Film, 62K, 2W, 1% MCHP122WF6202T4E Resistor, Thick Film, 430K, 2W, 1% MCHP122WF4303T4E Resistor, Thick Film, 68K, 2W, 1% MCHP122WF6802T4E Resistor, Thick Film, 470K, 2W, 1% MCHP122WF4703T4E Resistor, Thick Film, 75K, 2W, 1% MCHP122WF7502T4E Resistor, Thick Film, 510K, 2W, 1% MCHP122WF5103T4E Resistor, Thick Film, 82K, 2W, 1% MCHP122WF8202T4E Resistor, Thick Film, 560K, 2W, 1% MCHP122WF5603T4E Resistor, Thick Film, 91K, 2W, 1% MCHP122WF9102T4E Resistor, Thick Film, 620K, 2W, 1% MCHP122WF6203T4E Resistor, Thick Film, 100K, 2W, 1% MCHP122WF1003T4E Resistor, Thick Film, 680K, 2W, 1% MCHP122WF6803T4E Resistor, Thick Film, 110K, 2W, 1% MCHP122WF1103T4E Resistor, Thick Film, 750K, 2W, 1% MCHP122WF7503T4E Resistor, Thick Film, 120K, 2W, 1% MCHP122WF1203T4E Resistor, Thick Film, 820K, 2W, 1% MCHP122WF8203T4E Resistor, Thick Film, 130K, 2W, 1% MCHP122WF1303T4E Resistor, Thick Film, 910K, 2W, 1% MCHP122WF9103T4E Resistor, Thick Film, 150K, 2W, 1% MCHP122WF1503T4E Resistor, Thick Film, 1M, 2W, 1% MCHP122WF1004T4E Resistor, Thick Film, 160K, 2W, 1% MCHP122WF1603T4E Important Notice : This data sheet and its contents (the Information ) belong to the members of the Premier Farnell group of companies (the Group ) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group s liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. Premier Farnell plc Page <7> 21/05/14 V1.0
Carbon Film Fixed Resistor Axial Leaded
Features Automatically insertable High quality performance Non-Flame type available Cost effective and commonly used Too low or too high values can be supplied on case to case basis Performance Specification
SPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
Automotive and Anti-Sulfuration Chip Resistor 0402
The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top surface of the
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
Features: High reliability. Very sharp reverse characteristic. Zener voltage 3.3V to 12V. V z -tolerance ±5%.
Features: High reliability. Very sharp reverse characteristic. Zener voltage 3.3V to 12V. V z -tolerance ±5%. Applications: Voltage stabilization. Absolute Maximum Ratings Parameter Test Conditions Symbol
TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
Tri-Rated Flexible PVC Equipment Wire
Application: High temperature, flame retardant wire designed for use in the switch control, relay and instrumentation panels of power switchgear and for purposes such as internal connectors in rectifier
SMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
Type RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
PVC Insulated Mains Cable
Series - 3182Y 2 Core Plain Annealed Copper Wire, PVC Insulation, PVC Sheath Insulation \ Sheath material : PVC : Blue, Brown Voltage : 300/500V 3182Y-0.5 0.5mm 2 16/0.2mm 2.2mm 6.2mm 62mm 39Ω/km 3A 3182Y-0.75
Power chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
W- Series. Features: WOB. Mechanical Data Case : Moulded plastic. Lead : Solder plated. Weight : 1.10 grams. Page <1> 15/07/08 V1.
Features: Surge overload ratings to 40 amperes peak. Ideal for printed circuit board. Reliable low cost construction. High temperature soldering guaranteed: 260 C/10 seconds/0.375inch (9.5mm) lead lengths
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
Metal Film Resistors, Industrial, Precision
Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Available Excellent high frequency characteristics Exceptionally
DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
Precision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
Power Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
Metal Film Resistors, Industrial, Precision
CMF Industrial Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
Thick Film Resistor Networks, Dual-In-Line, Molded DIP
Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS RL-High power series 5%, 2%, 1% sizes 0805/1206
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS series 5%, 2%, 1% sizes 005/1206 RoHS compliant Product specification Aug 27, 200 V.2 Product specification 2 SCOPE This specification describes RL005/1206
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
ESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips
ESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips thick film chip resistors are specially designed to meet the requirements of the ESA 4001/026 specification. They have undergone the
Diode, Schottky SMB/DO-214AA. Page <1> 24/04/08 V1.1. Dimensions Inches (Millimeters)
Features: For surface mounted application. Metal to silicon rectifier, majority carrier conduction. Low forward voltage drop. Easy pick and place. High surge current capability. Plastic material. Epitaxial
DATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
High-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
SIL Resistor Network. Resistors. Electrical. Environmental. L Series. Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant
Resistors SIL Resistor Network Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Standard Resistance
High Ohmic/High Voltage Metal Glaze Leaded Resistors
VR37 High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded
Standard Thick Film Chip Resistors
Standard Thick Film Chip Resistors FEATURES Stability R/R = 1 % for 00 h at 70 C 2 mm pitch packaging option for size Pure tin solder contacts on Ni barrier layer provides compatibility with lead (Pb)-free
Metal Film Resistors, Non-Magnetic, Industrial, Precision
Metal Film Resistors, Non-Magnetic, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
SMD PTC - Nickel Thin Film Linear Thermistors
SMD PTC - Nickel Thin Film Linear Thermistors Notes (1) Contact if closer TCR lot tolerance is desired. (2) Other R 25 -values and tolerances are available upon request. (3) Rated continuous working voltage
High-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
High Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
High Ohmic/High Voltage Metal Film Leaded Resistors
, High Ohmic/High Voltage FEATURES Metal film technology High pulse loading (up to 10 kv) capability Small size (0207/0411) Compatible with lead (Pb)-free and lead containing soldering processes Compliant
Pulse Proof Thick Film Chip Resistors
Pulse Proof Thick Film Chip Resistors FEATURES High pulse performance, up to kw Stability R/R 1 % for h at 70 C AEC-Q200 qualified Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
BUX48 High Power Bipolar Transistor
High oltage Switching Features: Collector-Emitter sustaining voltage- CEO(sus) = 400 (Minimum) - BUX48 = 450 (Minimum) -. Collector-Emitter saturation voltage- CE(sat) = 1.5 (Maximum) at I C = 10A for
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) Rotor. Wiper. Cover. Pin S T - 2 T A 1 0 0 Ω ( 1 0 1 )
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) COPAL ELECTRONICS RoHS compliant INTERNAL STRUCTURE 8 4 7! 5! 9 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7
ST-2 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) FEATURES PART NUMBER DESIGNATION S T - 2 T A 1 0 0 Ω ( 1 0 1 ) RoHS compliant
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 8 4 7 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7 8 9!! 5 Part name Housing
BC107/ BC108/ BC109 Low Power Bipolar Transistors
TO-18 Features: NPN Silicon Planar Epitaxial Transistors. Suitable for applications requiring low noise and good h FE linearity, eg. audio pre-amplifiers, and instrumentation. TO-18 Metal Can Package Dimension
Metal Film Resistors, Industrial, Flameproof
End of Life - August 13 Metal Film Resistors, Industrial, Flameproof STANDARD ELECTRICAL SPECIFICATIONS FEATURES Small physical size Low cost resistors have the ability to withstand overloads up to times
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
DATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',
Insulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
Features: Characteristic Symbol Rating Unit. Collector-Emitter Voltage V CEO 100 Collector-Base Voltage I C
Designed for use in general purpose power amplifier and switching applications. Features: Collector-Emitter Sustaining Voltage V CEO(sus) = 100V (Minimum) - TIP35C, TIP36C DC Current Gain h FE = 25 (Minimum)
Power Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
Flat Flexible Cable 0.5mm, 1.0mm and 1.25mm Pitch
Flat Flexible Cables consist of flat tin plated copper conductors insulated between Polyester based tapes. Depending on the type of interconnection used, reinforcement tapes can be added to the cable ends
Metal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
Metal Film Resistors, Military, Qualified, Precision, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient Flame retardant
FEATURES 200 % 175 % 150 % 125 % 100 % 75 % 50 % 25 %
Ultra High Precision Z-Foil Resistor with TCR of ± 0.05 ppm/ C, PCR of 5 ppm at Rated Power, Tolerance of ± 0.005 % and Load Life Stability of ± 0.005 % INDUSTRY BREAKTHROUGH Any value at any tolerance
Pulse Proof, High Power Thick Film Chip Resistors
Pulse Proof, High Power Thick Film Chip Resistors STANDARD ELTRICAL SPIFICATIONS MODEL CASE SIZE INCH CASE SIZE METRIC POWER RATING P 70 W LIMITING ELEMENT VOLTAGE U max. AC/DC -HP e3 FTURES Excellent
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
TIP31, TIP32 High Power Bipolar Transistor
Features: Collector-Emitter sustaining voltage - V CEO(sus) = 60V (Minimum) - TIP31A, TIP32A = 100V (Minimum) - TIP31C,. Collector-Emitter saturation voltage - V CE(sat) = 1.2V (Maximum) at I C = 3.0A.
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
Silicon temperature sensors. Other special selections are available on request.
Rev. 05 25 April 2008 Product data sheet 1. Product profile 1.1 General description The temperature sensors in the have a positive temperature coefficient of resistance and are suitable for use in measurement
High Stability - High Temperature (230 C) Thin Film Wraparound Chip Resistors, Sulfur Resistant
High Stability - High Temperature (230 C) Thin Film Wraparound Chip Resistors, Sulfur Resistant INTRODUCTION For applications such as down hole applications, the need for parts able to withstand very severe
SC Series: MIS Chip Capacitors
DATA SHEET SC Series: MIS Chip Capacitors Applications Systems requiring DC blocking or RF bypassing Fixed capacitance tuning element in filters, oscillators, and matching networks Features Readily available
Product Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
Power Dissipation Considerations in High Precision Vishay Sfernice Thin Film Chips Resistors and Arrays (P, PRA etc.) (High Temperature Applications)
VISHAY SFERNICE Resistive Products Application Note ABSTRACT On our thin film chips resistors and arrays the main path for the heat, more than 90 %, is conduction through the body of the component, the
Low forward voltage High breakdown voltage Guard-ring protected Hermetically sealed glass SMD package
Rev. 6 10 September 2010 Product data sheet 1. Product profile 1.1 General description Planar with an integrated guard ring for stress protection, encapsulated in a small hermetically sealed glass SOD80C
Precision Leaded Resistors
FEATURES Approved according to CECC 40101-806 Advanced thin film technology Low TC: ± 15 to Precision tolerance of value: ± 0.1 % and ± 0.25 % Superior overall : class 0.05 Wide precision range: 10 Ω to
High Surge Axial Cemented Wirewound Resistors
High Surge Axial Cemented Wirewound Resistors FEATURES High voltage surge (up to 12 kv) withstanding capability Non flammable silicon cement coating High grade ceramic core Material categorization: for
EVERGREEN (C.P.) USA INC. TEL: (650) 952-8091 FAX: (650) 952-3629 E-MAIL: sales@evergreencpusa.com. SPECIFICATIONS Lithium Battery CR123A- 1700mAh
Voltage (V) Voltage (V) Voltage (V) EVERGREEN (C.P.) USA INC. SPECIFICATIONS Lithium Battery CR123A- 1700mAh Temperature characteristics(20ma) (mah) Pulse discharge characteristics Model CR123A Nominal
FT-63 SINGLE TURN CERMET TRIMMERS FEATURES. PART NUMBER DESIGNATION F T - 6 3 E T V 5 k Ω ( 5 0 2 ) RoHS compliant
SINGLE TURN FT-6 RoHS compliant INTERNAL STRUCTURE 4 FEATURES RoHS compliant Resistance tolerance ± 0 % O ring sealed and washable Suitable for automatic insertion and automatic adjustment Increase in
Metal Film Resistors, Military, MIL-R-10509 Qualified, Type RN and MIL-PRF-22684 Qualified, Type RL
CMF (Military RN and RL) Metal Film Resistors, Military, Qualified, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient
4 A CAPACITY, THE VARIETY OF CONTACT ARRANGEMENTS FEATURES
4 A CAPACITY, THE VARIETY OF CONTACT ARRANEMENTS S RELAYS FEATURES 28. 1.12 12..472 1.4.49 The variety of contact arrangements 2 Form A 2 Form B, 3 Form A 1 Form B, 4 Form A Latching types available High
ATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
If there is any doubt about the results, measurement shall be made within the following limits : Ambient temperature 25±3 Relative humidity 40%~70%
APPROVED : Tin SHEET : 2 of 10 Standard atmospheric conditions Unless otherwise specified, the standard range of atmospheric conditions for making measurement and tests are as follow : Ambient temperature
Metal Film Resistors, Pulse Withstanding Protective
End of Life - August 213 www.vishay.com Metal Film Resistors, Pulse Withstanding Protective STANDARD ELECTRICAL SPECIFICATIONS GLOBAL HISTORICAL POWER RATING P 7 C W FEATURES Special design provides lightning
INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
NOT RECOMMENDED FOR NEW DESIGNS
28 Volt NOT RECOMMENDED FOR NEW DESIGNS Features Attenuation 0 db from 110 khz to 0 MHz Operating temperature - to +8 C Nominal 28 V input, 0 V to 0 V operation 1.7 to A throughput current Transient suppression
Thick Film Chip Resistors, Military/Established Reliability MIL-PRF-55342 Qualified, Type RM
Thick Film Chip Resistors, Military/Established Reliability -PRF-55342 Qualified, Type RM MATERIAL SPECIFICATIONS Resistive element Ruthenium oxide Encapsulation Epoxy Substrate 96 % alumina Termination
Interference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
1/2" (12.7 mm) Conductive Plastic and Cermet Potentiometer
1/2" (12.7 mm) Conductive Plastic and Cermet Potentiometer FEATURES Robust construction High rotational life (50 000 cycles) Up to three sections PC support plates Rotary switches and solder lugs terminals
Knob Potentiometer with Switch
Knob Potentiometer with Switch The is a revolutionary concept in panel mounted potentiometers. This unique design consists of a knob driving and incorporating a cermet potentiometer. Only the mounting
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions FEATURES Polarized energy storage capacitor with high capacity and energy density Energy version with high stability available
Ultra Precision Metal Film Leaded Resistors
Ultra Precision Metal Film Leaded Resistors FEATURES Exceptional low TCR: ± 2 ppm/k to ± 10 ppm/k Super tight tolerance: ± 0.01 % to ± 0.25 % Exceptional overall stability: class 0.02 Wide resistance range:
Mounting instructions for SOT78 (TO-220AB); SOT186A (TO-220F)
Mounting instructions for SOT78 (TO-220AB); SOT186A (TO-220F) Rev. 1 29 May 2012 Application note Document information Info Keywords Abstract Content SOT78; SOT186A; TO-220AB; TO-220F This application
Schottky barrier quadruple diode
Rev. 3 8 October 2012 Product data sheet 1. Product profile 1.1 General description with an integrated guard ring for stress protection. Two electrically isolated dual Schottky barrier diodes series, encapsulated
SMS7630-061: Surface Mount, 0201 Zero Bias Silicon Schottky Detector Diode
DATA SHEET SMS7630-061: Surface Mount, 0201 Zero Bias Silicon Schottky Detector Diode Applications Sensitive RF and microwave detector circuits Sampling and mixer circuits High volume wireless systems
NTC Thermistors, Radial Leaded and Coated
M, C, T NTC Thermistors, Radial Leaded and Coated FEATURES Small size - conformally coated Wide resistance range Available in 11 different R-T curves Available in point matched and curve tracking precision
MBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Professional www.vishay.com. Professional Metal Film Leaded Resistors
,, - Professional Professional Metal Film Leaded Resistors DESCRIPTION,, and professional leaded thin film resistors are the general purpose resistor for all fields of professional electronics where reliability
High Ohmic / High Voltage Metal Glaze Leaded Resistors
High Ohmic / High Voltage Metal Glaze Leaded Resistors A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper
Medium power Schottky barrier single diode
Rev. 03 17 October 2008 Product data sheet 1. Product profile 1.1 General description Planar medium power Schottky barrier single diode with an integrated guard ring for stress protection, encapsulated
BAT54 series SOT23 Schottky barrier diodes Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description
SOT2 Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description Planar with an integrated guard ring for stress protection, encapsulated in a small SOT2 (TO-26AB) Surface-Mounted
Optocoupler, Phototransistor Output, with Base Connection
4N25, 4N26, 4N27, 4N28 Optocoupler, Phototransistor Output, FEATURES A 6 B Isolation test voltage 5000 V RMS Interfaces with common logic families C 2 5 C Input-output coupling capacitance < pf NC 3 4
Knob Potentiometer FEATURES. P16NP P16NM Panel Cutout. Thickness nut 2 mm washer 1.5 mm. Panel sealing ring 12 wrench Thread M10 x 0.75 10.2 9.
Knob Potentiometer P6, PA6 FEATURES Test according to CECC 4000 or IEC 60393- P6 - Version for professional and industrial applications (cermet) W at 40 C PA6 - Version for professional audio applications
Features. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND
DATASHEET IDT5P50901/2/3/4 Description The IDT5P50901/2/3/4 is a family of 1.8V low power, spread spectrum clock generators capable of reducing EMI radiation from an input clock. Spread spectrum technique
Part Marking Instructions Chip Resistors
Chip Resistors Part Marking Instructions Part Marking Instructions Chip Resistors 1% Marking The nominal resistance is marked on the surface of the overcoating with the use of 4 digit markings. 0201 and
DS 600. A contact free flux gate based current measurement sensor 600A rms
DS 600 A contact free flux gate based current measurement sensor 600A rms DS 600 is member of the small housing sensor family. The family includes a 200A and a 600A version. 600A rms - 900A peak Maximum
ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS514 Description The ICS514 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a 14.31818 MHz crystal or clock input. The name LOCO stands for
10 ma LED driver in SOT457
SOT457 in SOT457 Rev. 1 20 February 2014 Product data sheet 1. Product profile 1.1 General description LED driver consisting of resistor-equipped PNP transistor with two diodes on one chip in an SOT457
Silicon PIN Photodiode
Silicon PIN Photodiode DESCRIPTION 94 8583 BPW34 is a PIN photodiode with high speed and high radiant sensitivity in miniature, flat, top view, clear plastic package. It is sensitive to visible and near