Installation instructions for latex and vinyl wall mural
|
|
- Dulcie Atkins
- 7 years ago
- Views:
Transcription
1 Installation instructions for latex and vinyl wall mural How to prepare the ground? The walls must be clean and dry before you start wallpapering. All cavities and holes need to be supplemented and corrected. You should also remove the striking boards, nails, switches and sockets. Which tools are needed? a brush a wallpaper knife a press roll a wallpapering brush wallpaper paste a paint film moreover: a plastic bucket, a level, a plumb, a ladder
2 At least 2 people are recommended to stick a wall mural. How to stick? After receiving a wall mural you have to expand it and put it on a clean and dry surface (face up). In the case of wall mural consisting of several ply (belts) all of them should be expanded. Then you have to check if printing has no manufacturing defects (discoloration, deformation, the differences in sizes and weights of individual elements or non graphic motif of their joints). 1. When the wall is prepared determine lightly in pencil the vertical lines. They will symbolize the edges of wall mural. Use a plumb or a level. 2. Take the glue we recommend Metylan Normal glue for wall murals for latex backing and Metylan Special glue for wall murals for vinyl backing (a wall mural paste should be applied according to manufacturer s instructions and recommendations). 3. Wall mural always should be stick from the window side in the order of its elements. 4. Start pushing the wall mural from the top getting rid of the bubbles air. 5. Use a press roll for pressing the wall mural. 6. Carefully push and smooth wall mural paying particular attention to the fact that the edges should be well pressed to the wall. 7. Gently remove the excess glue with a damp soft cloth or sponge. 8. The next belts (if wall mural consists of several elements) should be placed in the same way. We stick them next to each other precisely (edge in the edge in the case of vinyl wall mural and with maximum two centimeters long tab in the case of latex wall mural*). 9. Leave a wall mural to dry for about 1-3 hours. *NOTE. If you have chosen a latex wall mural with plastic coating as an option, you have to stick it edge in the edge.
3 How to stick an adhesive wall mural? How to prepare the ground? The walls must be clean and dry before you start wallpapering. All cavities and holes need to be supplemented and corrected. You should also remove the striking boards, nails, switches and sockets. Which tools are needed? a knife a felt squeegee a spray with water a petroleum ether At least 2 people are recommended to stick a wall mural. How to stick? After receiving a wall mural you have to expand it and put it on a clean and dry surface (face up). In the case of wall mural consisting of several ply (belts) all of them should be expanded.
4 Then you have to check if printing has no manufacturing defects (discoloration, deformation, the differences in sizes and weights of individual elements or non graphic motif of their joints). Technique of dry (on the materials such as: a plasterboard panel, a sliding, a concrete etc.) 1. Remember: technique of dry can be used only on dry surfaces: plasterboard panel, sliding, concrete, walls. 2. Wall mural always should be stick from the window side in the order of its elements. If you stick a wall mural on vertical surfaces, it is recommended to start from the top. If you stick a wall mural on a flat or horizontal surfaces, it doesn t matter which side you choose for the start. 3. When the wall is prepared determine lightly in pencil the vertical lines. They will symbolize the edges of wall mural. Use a plumb or a level. 4. Then you have to peel centimeters of wall mural off. Wrap backing paper underneath. WARNING! DON T SPRAY GROUND BY THE WATER. 5. We put the film evenly. First person smoothes sticking surface by a felt squeegee pushing air bubbles out. Second person pulls the whole belt and folds the backing paper. 6. The next belts (if wall mural consists of several elements) should be placed edge in the edge. Wet technique (on the materials such as: a glass, a wood, a metal etc.) 1. Remember: Wet technique can be used only on surfaces which can be wet: a glass, a wood, a metal etc. which mean furniture, windows, fridges, plastic trim. 2. Wall mural always should be stick from the window side in the order of its elements. If you stick a wall mural on vertical surfaces, it is recommended to start from the top. If you stick a wall mural on a flat or horizontal surfaces, it doesn t
5 matter which side you choose for the start. 3. When the wall is prepared determine lightly in pencil the vertical lines. They will symbolize the edges of wall mural. Use a plumb or a level. 4. Then you have to peel centimeters of wall mural off. Wrap backing paper underneath. The paint film should be sprayed by the water on the adhesive surface. You should spray the begging of the sticking ground too. 5. We put the film evenly. First person smoothes sticking surface by a felt squeegee pushing air bubbles out. Second person pulls the whole belt and folds the backing paper. Each time you peel off the backing paper you should spray by the water both surfaces: wall mural and sticking ground. 6. The next belts (if wall mural consists of several elements) should be placed edge in the edge. Compliance with the instructions above should prevent you from the air bubbles under the photo wall mural. But when they are formed it is easy to puncture them by a sharp needle and smoothes them by a felt squeegee. How to stick a Smart Stick wall mural? How to prepare the ground? The walls must be clean and dry before you start wallpapering. All cavities and holes need to be supplemented and corrected. You should also remove the striking boards, nails, switches and sockets.
6 Which tools are needed? a level a pencil At least 2 people are recommended to stick a wall mural. How to stick? After receiving a wall mural you have to expand it and put it on a clean and dry surface (face up). In the case of wall mural consisting of several ply (belts) all of them should be expanded. Then you have to check if printing has no manufacturing defects (discoloration, deformation, the differences in sizes and weights of individual elements or non graphic motif of their joints). 1. When the wall is prepared determine lightly in pencil the vertical lines. They will symbolize the edges of wall mural. Use a level. 2. Photo wall mural always should be stick from the window side in the order of its elements. 3. We put the film evenly. First person smoothes sticking surface by a felt squeegee pushing air bubbles out. Second person pulls the whole belt. If you have wrinkles or bubbles peel wall mural off and stick it again. This is possible with Smart Stick! 4. The next belts (if photo wall mural consists of several elements) should be placed in the same way precisely edge in the edge. 5. You can stick Smart Stick repeatedly! Here you ll find a short instructional videos:
7 How to stick a wall sticker? The wall must be clean and dry before you start wallpapering. Without dust and trace of fat. Don t stick on the raw plaster. You should 3-4 days after a new painting to fully dry paint. Surfaces such as a glass or a metal which mean furniture, windows or refrigerators should be degreased with water mixed with dishwashing liquid. Which tools are needed? a knife a flat squeegee or a paper towel Only 1 person is required to stick a small wall sticker. Bigger stickers require at least 2 people. How to stick? Wall sticker consists of three layers: silicone backing paper appropriate adhesive sticker with a cut pattern with powerful bond transport adhesive film with low bonding strength* *Transport film is present only with the sticker cut along the contour (so-called wall tattoo)
8 1. After receiving the wall sticker you expand it and put it on the clean, dry and hard surface (preferably on the table). Transport film to the bottom. 2. Before sticking you should smooth a sticker by a flat squeegee or by rolled-up paper towel to push each other three layers. 3. Then you have to peel the backing paper off (at an angle close to 180 degrees). The short side should always be first (the sticker must stay on the transport film). If any of the elements didn t want to move away from the paper press it to the transport film. 4. Try a motif on the wall, gently stick and the press to the wall by a flat squeegee or by a rolled-up paper towel getting rid of air bubbles. 5. Another piece of backing paper should be peeled off slowly and in stages under the angle close to 180 degrees. Stick to the wall and press in the same way as in the previous step. 6. Repeat it until you get rid of the whole backing paper. 7. Smooth the whole again for best fitting (before peeling the transport film off). 8. Then you have to begin peeling the transport film off slowly. Always from the shorter side at angle close to 180 degrees. 9. After peeling the transport film off each element of the sticker should be smoothed in order to increase the adhesion. Here you ll find a short instructional videos: a small sticker a big sticker
DIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationVC 104+ Rigid Grade / Rigid Grade Imagine VC 104 Rigid Grade Commercial Customised
Page 1 of 6 instructions VC 104+ Rigid Grade / VC 104+ Rigid Grade Imagine / (for the rest of this document referred to as VC 104) can be applied to new and used trucks and trailers with painted rigid
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationDASH KIT INSTALLATION
ÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿ ÿÿÿÿÿ ÿÿ ÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿ ÿÿÿÿ ÿÿ ÿÿÿÿÿ ÿÿÿÿÿÿÿÿ PROUDLY MADE IN THE USA DASH KIT INSTALLATION These instructions are aimed at the do-it-yourself installer. Read
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationHendricks 40m 15m SOTA EFHW Tuner
Hendricks 40m 15m SOTA EFHW Tuner First, familiarize yourself with the parts and check for all the components. Parts Inventory 1 - Tayloe SWR Indicator kit 1 - T50-6 core (yellow), T94-2 (red) core not
More informationBLADE REPAIR INSTRUCTION BOOKLET
BLADE REPAIR INSTRUCTION BOOKLET Contents Section I: Section II: Section III: Section IV: Section V: Section VI: Removing a Blade Refer to this section if you need to remove the blade from an oar shaft.
More informationSurface Decoration. Design techniques used to put on the surface of the pottery. Slip Oxides Glaze Embossed Incised Wax on wet Altered from the wheel
Surface Decoration Design techniques used to put on the surface of the pottery. Slip Oxides Glaze Embossed Incised Wax on wet Altered from the wheel Slip How to apply slip Colored slip is intended to add
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationAspect Metal Peel & Stick Tile Installation Guide
Aspect Metal Peel & Stick Tile Installation Guide Proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty Read
More informationSelection, Use, and Care of Brushes
Wood Finishing & Refinishing Fact Sheet #2 Selection, Use, and Care of Brushes Dr. Leona K. Hawks Home Furnishings and Housing Specialist 1995 HI 22 Good results in wood refinishing depend to a large extent
More informationApplication Instructions for Avery Dennison Films SF100-843-S LTR EZ RS, Conform Chrome
Application Instructions for Avery Dennison Films SF100-843-S LTR EZ RS, Conform Chrome Instructional Bulletin #4.00.2 (Revision 0) Dated: 04/05/2012 1.0 Consult Product Data Bulletin Before starting application,
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationMaking A Mirror Grinding Tool By Allen Malsburry
Making A Mirror Grinding Tool By Allen Malsburry The average person would never think, I can make my own telescope. Most amateur astronomers believe, I can buy a better telescope than I can build. Neither
More informationBlack Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Black Wolf TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905710-000 SEPTEMBER 2010 NOTE: Please use the instructions in this
More informationAcrylic Walls Installation Instructions
Acrylic Walls Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower acrylic walls. If you have any questions on this shower acrylic walls installation
More informationBrisa UV Gel Enhancements Sculpted on a Tip
Step-by-Step Guide Brisa UV Gel Enhancements Sculpted on a Tip 90 MIN A service designed for problem nails with no natural nail extension edge, requiring length and re-design. STEP 1: P.R.E.P. f. Apply
More informationArmstrong Do-It-Yourself Tile Installation System
Armstrong Do-It-Yourself Tile Installation System What tools will I need to install my tile floor? You'll need just the basics: - floor tile (make sure you have enough tile to finish the job) - adhesive
More informationFabric Replacement Top Installation Instructions
Replacement Top Installation Instructions For: Wrangler/YJ 88-95 Part Number: 51120 Special Note: If your Wrangler is a 1986 or 1987 model, this kit is not the correct product. Please order Part Number
More informationFAQs. 19. Does the sub floor need to be level before I install my new direct-to-stud bathtub or shower base?
1. Where is the serial number of my tub located? 2. What can I use to clean my tub or shower? 3. What is an Above Floor Rough-in? 4. Can I replace my towel bar? 5. What are grommets? 6. Why do some bathing
More informationScotchgard Multi-Layer Protective Film 1004
Scotchgard Multi-Layer Protective Film 1004 3 Technical Bulletin September, 2008 Scotchgard Multi-Layer Protective Film 1004 Application Kit (3M Part No. 70-0710-4666-1) includes: (clockwise) Heavy Duty
More informationTrūShine Gel Enamel FAQs
Q. Is TrūShine Gel Enamel 5-Free? TrūShine Gel Enamel FAQs Yes. All TrūShine Gel Enamel formulas are without DBP, Formaldehyde, Toluene, Formaldehyde Resin, and Camphor. Q. Can Host Rewards be applied
More informationBALLOON & PAPER MACHE LANTERN
BALLOON & PAPER MACHE LANTERN Need: Balloon, blown up to desired size Glue & water mixture, 50/50 mix Tissue paper, torn or cut into small pieces Small paint brush 1 works well Thin bendable wire or string
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. GeneralShale.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide GeneralShale.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationLay blocks with mortar
Student Lay blocks with mortar What you will learn When you have fi nished this section, you should be able to: Mix mortar Lay blocks with correct mortar joints. How do I mix mortar? Mortar is a wet paste
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationCordlessPleated FabricShade including Top-Down/Bottom-Up. owner's handbook
CordlessPleated FabricShade including Top-Down/Bottom-Up owner's handbook July, 2013 español página 9 2 INSTALLATION INSTRUCTIONS Step 1. Check Package Contents Missing part? Call 1-800-264-1190 Mounting
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationTHINGS YOU SHOULD KNOW
INSTALLATION INSTRUCTIONS Value Sized Roll The quickest, easiest, cleanest way to install tile. No Mortar, No Mixing, No Mess Complete Your Project in a Day No Waiting Between Setting and Grouting THINGS
More informationSterile Dressing Change with Tegaderm CHG for Central Venous Catheter (CVC)
Sterile Dressing Change with Tegaderm CHG for Central Venous Catheter (CVC) The dressing protects your catheter site. It also helps prevent infection at the site. Keep your dressing clean and dry at all
More informationLesson One: Etching with Vinyl
Lesson One: Have you ever wanted to learn the art of glass etching but aren t sure where to start? Are you etching but not getting the finish you d like? We ll explore how to use the Silhouette Cutting
More informationLaminate Flooring T-Lock Angle-Drop Installation Instructions
TECHNICAL SERVICE Laminate Flooring T-Lock Angle-Drop Installation Instructions March 23, 2012 Read all instructions carefully before beginning installation. Make sure that the instructions are the most
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationBUNK BED. Model No.: DA3797E - Espresso DA3797P- Pine. UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: Lot number: Date of purchase:
BUNK BED Model No.: DA3797E - Espresso DA3797P- Pine UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
More informationWall Mount Installation and Use
Wall Mount Installation and Use 1. Introduction The Wall Mount works the same way for all Touchfire cases - the one or two row magnet strip on the back of the case is magnetically attracted to the Wall
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationClay Feature Tutorial
Clay Feature Tutorial This tutorial can be used to apply any type of feature to a vinyl doll. Keep in mind that baked clay will be NON-flexible whereas, vinyl will remain flexible. In the following photos,
More informationTable of Contents Markers...1
Table of Contents Markers...1 Introduction...1 Color Surge Paper...2 Color Surge\Neon Explosion/Glow Board/Color Wave Markers...3 Dry Erase Markers...9 Erasable Markers...15 Ice Markers...23 Markers...34
More informationSPM-2 PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
SPM-2 PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE. CONGRATULATIONS You are now the proud, new owner of a SMART PLANET Mini SUPERPRETZEL Soft Pretzels Maker with Melting Pod
More informationHow to Fill a Cavity WHEN NOT TO PLACE A FILLING CHAPTER10
143 How to Fill a Cavity CHAPTER10 When someone s tooth hurts, you do not always need to take it out. There may be a way to treat it and keep it. Always ask yourself whether a bad tooth really needs to
More informationBeadboard Wall Bookcase
Beadboard Wall Bookcase Note: The maximum load for each shelf is 30lbs.This hanging system is meant for drywall/wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
More informationSHELLAC Brand Application & Removal
Step-by-Step Guide SHELLAC Brand & Removal 45 MIN SHELLAC Brand 14+ Day Nail Color combines the ease of polish with incomparable high-performance wear and stunning crystal shine. A true innovation in chip-free,
More informationHow to Install Drop Ceiling Panels
How to Install Drop Ceiling Panels Both Ceilume s 0.013 thick Feather-Light and 0.030 thick Signature Ceiling Tiles can be installed in an approved ceiling suspension system using standard 15/16 face T-bar
More informationStep-by-Step Guide. ENHANCEMENTS Brisa UV Gel Enhancements Rebalancing. STEP 1: Cleanse
Step-by-Step Guide ENHANCEMENTS Brisa UV Gel Enhancements Rebalancing 1 HOUR Rebalancing is a method of maintaining the balance and beauty of the enhancement while the natural nail grows. Proper rebalancing
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationIMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Step 1:
IMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Thank you for purchasing your new replacement windows from Great Lakes Window. The following instructions will help remove the old windows
More informationContents. Introduction... A Note About Heatsinks... Precautions...
Contents Introduction... A Note About Heatsinks... Precautions... Application Instructions... Heatsink Preparation... CPU Preparation... Tinting the Heatsink and Metal cap... Applying Thermal Compound...
More informationSite sampling and testing of concrete
Sampling amended booklet amended:layout 1 4/8/09 14:14 Page 1 A practical guide for site personnel Site sampling and testing of concrete Cubes have a vital role to test that the concrete strength meets
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationBasement Window Installation Guide Hopper and Sliding
Basement Window Installation Guide Hopper and Sliding americancraftsmanwindows.com Project Requirements: Installation must comply with all applicable building codes. Existing window frame, wall and weatherresistant
More informationGARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS
GARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS DE-GLAZING 1.) If there is any PVC cement covering the joints where external glazing bead strips meet, cut through the cement with a utility knife. 2.)
More informationHow To Level A Subfloor
Skill Level: INTERMEDIATE Give these projects a try if you're a confident DIYer with a good working knowledge of a variety of tools. They can take a day or more to complete. If you can build a birdhouse
More informationBarewood Octagon and Elongated Windows Installation Instructions
Step-by-step instructions to a beautiful window. Measuring and Installation of your new window from Century Specialty Windows couldn't be easier with our step-by-step instructions. Quality, function and
More informationJOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING. Test Code: 2060 Version: 01
JOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING Test Code: 2060 Version: 01 Specific Competencies and Skills Tested in this Assessment: Wood Finishes Identify thinning products Identify wood finish
More informationThis topic explores the key concepts of magnetism as they relate to: the phenomenon of magnetism magnetic forces and fields a theory of magnetism.
Magnetism Introduction This topic explores the key concepts of magnetism as they relate to: the phenomenon of magnetism magnetic forces and fields a theory of magnetism. Key concepts of magnetism The activities
More informationReplacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin americancraftsmanwindows.com Project Requirements: Failure to follow these instructions may void product
More informationThe Hive Bodies. In the Beekeeper s Work Shop. Building a Bee Hive: The Hive Bodies. by Stephen E. Tilmann
The Hive Bodies In the Beekeeper s Work Shop The hive body is the heart of a managed bee hive colony (Figure 1). It is where the queen lays her eggs, the house bees raise the brood and the workers store
More informationXPULT INSTRUCTIONS BASIC VERSION
XPULT INSTRUCTIONS BASIC VERSION The Xpult is a device for launching table tennis balls or other light plastic balls. Most likely, you will have received the Xpult from your teacher or somebody else who
More informationPATIENT GUIDE. Care and Maintenance Drainage Frequency: Max. Drainage Volume: Dressing Option: Clinician s Signature: Every drainage Weekly
PATIENT GUIDE Care and Maintenance Drainage Frequency: Max. Drainage Volume: Dressing Option: Every drainage Weekly Clinician s Signature: ACCESS SYSTEMS Pleural Space Insertion Site Cuff Exit Site Catheter
More informationPAINT. PAINTING WALLS... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP... 118
PAINT PAINTING WALLS...... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP....... 118 112 Basic Construction Safety SAFETY TALK #1: Drink plenty of water and watch for dehydration! When
More informationGear PEPSI CAN STOVE INSTRUCTIONS
Gear PEPSI CAN STOVE INSTRUCTIONS [NOTE: Updated Instructions are now available. The new stove is less likely to develop flame leaks and the fuel/air mixture is improved. Instructions for a simmer ring
More informationBydureon 2 mg powder and solvent for prolonged-release suspension for injection in pre-filled pen How to use Bydureon pre-filled pen
INSTRUCTIONS FOR THE USER Read these instructions carefully before use Bydureon 2 mg powder and solvent for prolonged-release suspension for injection in pre-filled pen How to use Bydureon pre-filled pen
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationRecord Cleaning Machine
Record Cleaning Machine Owner s Manual UK December 2010 Photo 1 Photo 2 IMPORTANT! READ THIS OWNER S MANUAL CAREFULLY, BEFORE USING THE MACHINE! Introduction You are now the proud owner of an Okki Nokki
More informationSEE HOW TO MAKE LIME PLASTER WHY USE LIME? PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013
SEE HOW TO MAKE LIME PLASTER PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013 WHY USE LIME? Lime plaster forms a light, clean, and durable surface that is resistant to weather and mold. A thin layer attaches
More informationChoosing the Right Floor Protectors
Choosing the Right Floor Protectors You ve made the investment in new flooring for your home. So what can you do to help ensure your flooring stays looking like new? One of the biggest flooring maintenance
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationGelatin Bubbles. Tami Utley. www.sugarartbytami.com. Materials:
Gelatin Bubbles By Tami Utley www.sugarartbytami.com Materials: Water Balloons Unflavored Gelatin Luster Dust (Super pearl or others) Toothpick or tweezers Small microwave safe bowl Duct tape Styrofoam
More informationEtching using chemicals
Etching using chemicals Free tutorial Artsandtechniques.com Arts and Techniques School RJDS inc. Etching using chemicals There are several ways to etch metal, this technique uses a chemical. The etching
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationThe tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results
Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs
More informationBathroom Installation Guide
Bathroom Installation Guide Step-by-step installation of your cabinets We do a lot of groundwork to make it as simple as possible for you to assemble and install your new bathroom furniture yourself. We
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationIMAGINE trying to paint a picture without a canvas or a
Identifying Floral Design Tools and Supplies IMAGINE trying to paint a picture without a canvas or a brush. Even with a wide variety of paints with which to work, you could not create the artwork without
More informationSCENIC VIEW SV 10 SECTION 08 87 13 SOLAR CONTROL FILMS
PART 1 GENERAL SCENIC VIEW SV 10 SECTION 08 87 13 SOLAR CONTROL FILMS 1.1 SUMMARY A. Optically clear dual reflective, neutral sputtered and aluminum metallized polyester film for solar control. 1.2 RELATED
More informationDriveCam Installation
www.lytx.com DriveCam Installation DriveCam VER Mounting Guidelines This document provides detailed instructions for mounting the DriveCam DC3/DC3P Video Event Recorder (VER) in a variety of vehicle types
More informationINSTALLATION RECOMMENDATIONS. Outdoor Rubber Tiles
INSTALLATION RECOMMENDATIONS Outdoor Rubber Tiles Prior to Installation: The Outdoor Rubber Tiles and accessory transition pieces intended for this installation have been shipped to you via a freight carrier
More informationHeavy Glass Frameless Shower Door With Return Panel
202 Anderson Ave., elvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com Heavy Glass Frameless Shower Door With Return Panel Full Showers with Return ench Seat with Return FRLSDRPL-0116
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW
Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Lea las instrucciones en español en el reverso.
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationVideo Killed the Radio Star! Watch a video of me explaining the difference between static and kinetic friction by clicking here.
Lesson 26: Friction Friction is a force that always exists between any two surfaces in contact with each other. There is no such thing as a perfectly frictionless environment. Even in deep space, bits
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationHow to become an Operation Christmas Child Shoe Box Character
How to become an Operation Christmas Child Shoe Box Character SUPPLIES A large rectangular box (to look like a shoe box) Cardboard or foam strips, 2 wide, for the lid Large printed Boy or Girl shoe box
More informationHow to build a Pizza Oven in 4 days
How to build a Pizza Oven in 4 days Preparation day (slab) 1. Foundation 1500 deep x 1300 wide x 75mm deep Required 20 bags cement pre mix. If you already have a concrete base, you save this prep day DAY
More informationMicro. Pitts Special for the RFFS-100 by Chris O Riley
Micro Pitts Special for the RFFS-100 by Chris O Riley F1 F2 F3 F4 1 2 3 4 All wood 1/32 inch sheet unless otherwise stated. F1 F2 F3 F4 Small balsa blocks for LG reinforcement Small balsa blocks for LG
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationwww.odometergears.com Ford Ranger and Mazda Pickup Odometer Worm Gear Replacement
www.odometergears.com Ford Ranger and Mazda Pickup Odometer Worm Gear Replacement http://www.therangerstation.com/magazine/fall2008/odometer_worm_gear.htm ****************************************************************************************************
More informationThe Enbrel SureClick autoinjector is a single-use prefilled autoinjector. It contains one 50-mg dose of Enbrel.
Instructions for Use Welcome! The Enbrel SureClick autoinjector is a single-use prefilled autoinjector. It contains one 50-mg dose of Enbrel. Your healthcare provider has prescribed Enbrel SureClick autoinjector
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (748-547) Chrysler 300 2005 10, Dodge Magnum 2005 08, Dodge Charger 2006 09 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not
More informationMcDonald s Kitchen Cleaning Instructions. Prepared for: Employees of McDonald s
McDonald s Kitchen Cleaning Instructions Prepared for: Employees of McDonald s Prepared By: Aracelly Arana TECM 2700 MWF 10-10:50 May 9, 2014 Table of Contents Table of Contents Table of Contents... iii
More informationOperator Quick Guide EC SENSOR
Operator Quick Guide EC SENSOR Revision G - 24/04/2008 General Information About This Guide The information in this guide has been carefully checked and is believed to be accurate. However, Hach Ultra
More informationA. Work on this project shall consist of, but is not limited to, the following:
PART 1 - GENERAL CLEANING AND RESTORATION OF SECTION 05900-1 1.1 SUMMARY A. Work on this project shall consist of, but is not limited to, the following: 1. Clean and treat all exposed anodized architectural
More informationCosmetics Case with Vinyl Interior Skill Level: Intermediate
Cosmetics Case with Vinyl Interior Skill Level: Intermediate Designed By Lindsey Rhodes Sewn By Lindsey Rhodes http://lrstitched.com Use this step by step tutorial to create a roll-up cosmetics case with
More informationRemoving paint. Project Guide. Difficulty. Experience/Time. Novice: 60 min. Experienced: 35 min. Pro: 20 min.
Removing paint Difficulty Experience/Time Novice: 60 min. Experienced: 35 min. Pro: 20 min. Removing old paint can be challenging, however there are several options available to help make the process easier
More informationINSTRUCTIONS FOR USE HUMIRA 40 MG/0.8 ML, 20 MG/0.4 ML AND 10 MG/0.2 ML SINGLE-USE PREFILLED SYRINGE
INSTRUCTIONS FOR USE HUMIRA (Hu-MARE-ah) (adalimumab) 40 MG/0.8 ML, 20 MG/0.4 ML AND 10 MG/0.2 ML SINGLE-USE PREFILLED SYRINGE Do not try to inject HUMIRA yourself until you have been shown the right way
More informationFrequently Asked Questions
What materials can I cut with the ScanNCut machine? The ScanNCut machine was developed with fabric cutting in mind. However, it is great for paper, cellophane, acetate, leather, craft vinyl, wood veneer,
More informationSEQUEL ASSEMBLY INSTRUCTIONS. 6003 Compact Desk CUSTOMERSERVICE@BDIUSA.COM
BIUSA.COM CUSTOMERSERVICE@BIUSA.COM Component List Sequel is engineered for easy assembly. Carefully follow this procedure to prevent any damage. A - 4mm Hex Wrench B - 1/4-20 x 12 mm Flat Head Machine
More information