European Technical Approval ETA-12/0481

Transcription

1 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel ax Internet Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products MEMBER O EOTA European Technical Approval ETA-12/0481 Trade name: Holder of approval: RAMPA Inserts Type SKL and BL Hans Brügmann GmbH & Co. Auf der Heide 8 DE Büchen Tel. +49 (0) ax +49 (0) Internet Generic type and use of construction product: Valid from: to: Manufacturing plant: This European Technical Approval contains: Self-tapping screws for use in timber structures Hans Brügmann GmbH & Co. Auf der Heide 8 DE Büchen 12 pages including 2 annexes which form an integral part of the document

2 Page 2 of 12 of European Technical Approval no. ETA-12/0481 I LEGAL BASIS AND GENERAL CONDITIONS 1 This European Technical Approval is issued by ETA-Danmark A/S in accordance with: - Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products 1), as amended by Council Directive 93/68/EEC of 22 July ). - Bekendtgørelse 559 af (afløser bekendtgørelse 480 af ) om ikrafttræden af E direktiv af 21. december 1988 om indbyrdes tilnærmelse af medlemsstaternes love og administrative bestemmelser om byggevarer. 5 Reproduction of this European Technical Approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of ETA-Danmark A/S. In this case partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European Technical Approval. 6 This European Technical Approval is issued by ETA- Danmark A/S in English. This version corresponds fully to the version circulated within EOTA. Translations into other languages have to be designated as such. - Common Procedural Rules for Requesting, Preparing and the Granting of European Technical Approvals set out in the Annex to Commission Decision 94/23/EC 3). 2 ETA-Danmark A/S is authorized to check whether the provisions of this European Technical Approval are met. Checking may take place in the manufacturing plant. Nevertheless, the responsibility for the conformity of the products to the European Technical Approval and for their fitness for the intended use remains with the holder of the European Technical Approval. 3 This European Technical Approval is not to be transferred to manufacturers or agents of manufacturers other than those indicated on page 1, or manufacturing plants other than those indicated on page 1 of this European Technical Approval. 4 This European Technical Approval may be withdrawn by ETA-Danmark A/S pursuant to Article 5(1) of Council Directive89/106/EEC. 1) Official Journal of the European Communities N o L40, 11 eb 1989, p 12. 2) Official Journal of the European Communities N o L220, 30 Aug 1993, p 1. 3) Official Journal of the European Communities N o L 17, 20 Jan 1994, p 34.

3 Page 3 of 12 of European Technical Approval no. ETA-12/0481 II SPECIAL CONDITIONS O THE EUROPEAN TECHNICAL APPROVAL Definition of the product RAMPA BL and SKL inserts are self-tapping screws to be used in timber structures. RAMPA BL and SKL screws shall be threaded over the full length. The inserts are produced from carbon steel No according to EN or stainless steel No according to EN , No or according to EN Where corrosion protection is required, the material or coating shall be declared in accordance with the relevant specification given in Annex A of EN Geometry and Material The nominal diameter (outer thread diameter), d, shall not be less than 10,0 mm and shall not be greater than 25,0 mm. The overall length, L, of inserts shall not be less than 30 mm and shall not be greater than 100 mm. Other dimensions are given in Annex A. The ratio of inner thread diameter to outer thread diameter d i /d ranges from 0,75 to 0,86. The screws are threaded over the total length l = l g (i.e. l g > 3 d). The lead p (distance between two adjacent thread flanks) ranges from 0,2 d to 0,33 d. No breaking of screws shall be observed at a bend angle, α, of less than (45/d 0,7 + 20) degrees. Note. The RAMPA inserts with a threaded length of 3 d are considered as having an effective minimum thread length of 4 d compared to conventional self-tapping screws. This is due to the fact that conventional self-tapping screws have a minimum threaded length of 4 d includes the point which does only partly contribute to the withdrawal capacity. Intended use The inserts are used for connections in load bearing timber structures between members of solid timber (softwood), glued laminated timber, cross-laminated timber, and laminated veneer lumber, similar glued members, woodbased panels or steel. Steel plates and wood-based panels except solid wood panels, laminated veneer lumber and cross laminated timber shall only be located on the side of the metric bolt acting as screw head. The following wood-based panels may be used: - Plywood according to EN 636 or European Technical Approval - Particleboard according to EN 312 or European Technical Approval - Oriented Strand Board according to EN 300 or European Technical Approval - ibreboard according to EN and or European Technical Approval (minimum density 650 kg/m³) - Cement bonded particleboard according to European Technical Approval - Solid wood panels according to EN and cross laminated timber according to European Technical Approval - Laminated Veneer Lumber according to EN or European Technical Approval - Engineered wood products according to European Technical Approval, provided that the ETA for the product provides provisions for the use of self-tapping screws and these provisions are applied The inserts shall be driven into the wood after pre-drilling with a diameter corresponding to the inner thread diameter for the total length of the insert. The inserts are intended to be used in timber connections for which requirements for mechanical resistance and stability and safety in use in the sense of the Essential Requirements 1 and 4 of Council Directive 89/106/EEC shall be fulfilled. The design of the connections shall be based on the characteristic load-carrying capacities of the inserts. The design capacities shall be derived from the characteristic capacities in accordance with Eurocode 5 or an appropriate national code. The inserts are intended for use for connections subject to static or quasi static loading. The scope of the inserts regarding resistance to corrosion shall be defined according to national provisions that apply at the installation site considering environmental conditions. Section 2.7 of this ETA contains the corrosion protection for RAMPA BL and SKL inserts made from carbon steel and the material number of the stainless steel. Assumed working life The assumed intended working life of the screws for the intended use is 50 years, provided that they are subject to appropriate use and maintenance. The information on the working life should not be regarded as a guarantee provided by the manufacturer or the approval body issuing the ETA. An assumed intended working life means that it is expected that, when this working life has elapsed, the real working life may be, in normal use conditions, considerably longer without major degradation affecting the essential requirements.

4 Page 4 of 12 of European Technical Approval no. ETA-12/ Characteristics of product and assessment Characteristic Assessment of characteristic 2.1 Mechanical resistance and stability*) Tensile strength Characteristic value f tens,k : d = 10,0 mm: d = 12,0 mm: d = 16,0 mm: d = 18,5 mm: d = 22,0 mm: d = 25,0 mm: 8,8 kn 13 kn 23 kn 31 kn 41 kn 41 kn Insertion moment Ratio of the characteristic torsional strength to the mean insertion moment: f tor,k / R tor,mean > 1, Torsional strength Characteristic value f tor,k : d = 10,0 mm: d = 12,0 mm: d = 16,0 mm: d = 18,5 mm: d = 22,0 mm: d = 25,0 mm: 9,0 Nm 25 Nm 40 Nm 80 Nm 130 Nm 180 Nm 2.2 Safety in case of fire Reaction to fire The screws are made from steel classified as Euroclass A1 in accordance with EN and EC decision 96/603/EC, amended by EC Decision 2000/605/EC 2.3 Hygiene, health and the environment Influence on air quality No dangerous materials **) 2.4 Safety in use Not relevant 2.5 Protection against noise 2.6 Energy economy and heat retention Not relevant Not relevant 2.7 Related aspects of serviceability Durability The screws have been assessed as having Serviceability satisfactory durability and serviceability when used in timber structures using the timber species described in Eurocode 5 and subject to the conditions defined by service classes 1. 2 and Identification See Annex A *) See page 7 of this ETA **) In accordance with In addition to the specific clauses relating to dangerous substances contained in this European Technical Approval, there may be other requirements applicable to the products falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction Products Directive, these requirements need also to be complied with, when and where they apply.

5 Page 5 of 12 of European Technical Approval no. ETA-12/ Mechanical resistance and stability The load-carrying capacities for RAMPA inserts are applicable to the wood-based materials mentioned in paragraph 1 even though the term timber has been used in the following. The characteristic lateral load-carrying capacities and the characteristic axial withdrawal capacities of RAMPA screws should be used for designs in accordance with Eurocode 5 or an appropriate national code. Point side penetration length must be l ef > 3 d, where d is the outer thread diameter of the insert. European Technical Approvals for structural members or wood-based panels must be considered where applicable. Lateral load-carrying capacity The characteristic lateral load-carrying capacity of RAMPA inserts shall be calculated according to EN :2008 (Eurocode 5) using the outer thread diameter d as the nominal diameter of the screw. The contribution from the rope effect may be considered. The characteristic yield moment shall be calculated from: Insert d = 10,0 mm: Insert d = 12,0 mm: Insert d = 16,0 mm: Insert d = 18,5 mm: Insert d = 22,0 mm: Insert d = 25,0 mm: M y,k = 17 Nm M y,k = 29 Nm M y,k = 65 Nm M y,k = 104 Nm M y,k = 156 Nm M y,k = 182 Nm The embedding strength for inserts in pre-drilled holes arranged at an angle between screw axis and grain direction, 0 α 90 is: 0,082 ρk (1 0,01 d) fh,k = [N/mm²] 2 2 2,5 cos α + sin α Where ρ k characteristic timber density [kg/m³]; d outer thread diameter [mm]; α angle between screw axis and grain direction. The embedding strength for inserts arranged parallel to the plane of cross laminated timber, independent of the angle between screw axis and grain direction, 0 α 90, shall be calculated from: fh,k 0,5 = 20 d [N/mm²] cross laminated timber should be assumed as for solid timber based on the characteristic density of the outer layer. If relevant, the angle between force and grain direction of the outer layer should be taken into account. The direction of the lateral force component shall be perpendicular to the screw axis and parallel to the wide face of the cross laminated timber. Axial withdrawal capacity The characteristic axial withdrawal capacity of RAMPA inserts in solid timber (softwood), glued laminated timber, cross-laminated timber or laminated veneer lumber members at an angle of 30 < α < 90 to the grain shall be calculated according to EN :2008 from: n 9 d l ρ = 1, 2 cos α + sin α 350 ef ef k ax, α,rk 2 2 Where ax,α,rk n ef d l ef characteristic withdrawal capacity of the inserts at an angle α to the grain [N] effective number of inserts according to EN :2008 outer thread diameter [mm] Penetration length of the threaded part according to EN :2008 [mm] α Angle between grain and screw axis (α > 30 ) ρ k Characteristic density [kg/m³] 0,8 [N] or inserts penetrating more than one layer of cross laminated timber, the different layers may be taken into account proportionally. The axial withdrawal capacity for screws arranged parallel to the plane of laminated veneer lumber and at an angle of 30 < α < 90 to the grain shall be reduced by 20 %. The axial withdrawal capacity is limited by the head pullthrough capacity of the metric bolt or washer and the tensile capacity of the insert. The axial slip modulus K ser of the threaded part of a screw for the serviceability limit state should be taken independent of angle α to the grain as: K ser = 780 d 0,2 l ef 0,4 [N/mm], Where d outer thread diameter [mm] penetration length in the timber member [mm] l ef Where d outer thread diameter [mm] The embedding strength for inserts in the wide face of

6 Page 6 of 12 of European Technical Approval no. ETA-12/0481 Tensile capacity The characteristic tensile strength f tens,k of RAMPA inserts is: d = 10,0 mm: d = 12,0 mm: d = 16,0 mm: d = 18,5 mm: d = 22,0 mm: d = 25,0 mm: f tens,k = 8,8 kn f tens,k = 13 kn f tens,k = 23 kn f tens,k = 31 kn f tens,k = 41 kn f tens,k = 41 kn and e.g. yellow or blue chromated. The mean thickness of the zinc coating is 5µm. Steel no according to EN , no or according to EN is used for screws made from stainless steel. The characteristic tensile capacity of RAMPA inserts shall be calculated according to EN :2008 from: { } = n min f ; 0,9 f A [N] tens,rk ef tens,k ub s Where tens,rk n ef f tens,k f ub A s Characteristic tensile capacity of the inserts [N] Effective number of inserts according to EN :2008 Characteristic tensile strength of a RAMPA insert [N] Characteristic tensile strength of the metric bolt inserted in the RAMPA insert [N/mm²] Tensile stress area of the bolt [mm²] Note. The values for the characteristic tensile strength and tensile stress area of the metric bolt depend on the metric bolt used in the specific application and therefore the characteristic tensile capacity of RAMPA inserts with metric bolts will be calculated on a case by case basis depending on the metric bolt used Combined laterally and axially loaded screws or connections subjected to a combination of axial and lateral load, the following expression should be satisfied: 2 2 ax,ed v,ed + 1 ax,rd v,rd where ax,ed axial design load of the insert v,ed lateral design load of the insert ax,rd design load-carrying capacity of an axially loaded insert v,rd design load-carrying capacity of a laterally loaded insert 2.7 Related aspects of serviceability Corrosion protection in service class 1, 2 and 3. The RAMPA inserts are produced from carbon steel wire no according to EN They are brassplated, nickel-plated bronze finished or electrogalvanised

7 Page 7 of 12 of European Technical Approval no. ETA-12/ Attestation of Conformity and CE marking 3.1 Attestation of Conformity system The system of attestation of conformity is 2+ described in Council Directive 89/106/EEC (Construction Products Directive) Annex III. a) Tasks for the manufacturer: (1) actory production control, (2) Initial type testing of the product, b) Tasks for the notified body: 3.2 Responsibilities (1) Initial inspection of the factory and the factory production control, (2) Continuous surveillance Tasks of the manufacturer actory production control The manufacturer has a factory production control system in the plant and exercises permanent internal control of production. All the elements, requirements and provisions adopted by the manufacturer are documented in a systematic manner in the form of written policies and procedures. This production control system ensures that the product is in conformity with the European Technical Approval. The manufacturer shall only use raw materials supplied with the relevant inspection documents as laid down in the control plan 4. The incoming raw materials shall be subject to controls and tests by the manufacturer before acceptance. Check of materials, such as sheet metal, shall include control of the inspection documents presented by suppliers (comparison with nominal values) by verifying dimension and determining material properties, e.g. chemical composition, mechanical properties and zinc coating thickness. The manufactured components shall be subject to the following checks: - Raw material specification; - Dimension of the screws; - Characteristic tensile strength f tens,k ; - Characteristic torsional strength f tor,k ; - Characteristic insertion moment R tor,k ; - Durability; - Marking. The control plan, which is part of the technical documentation of this European Technical Approval, includes details of the extent, nature and frequency of testing and controls to be performed within the factory production control and has been agreed between the approval holder and ETA Danmark. The results of factory production control are recorded and evaluated. The records include at least the following information: - Designation of the product, basic material and components; - Type of control or testing; - Date of manufacture of the product and date of testing of the product or basic material and components; - Result of control and testing and, if appropriate, comparison with requirements; - Signature of person responsible for factory production control. The records shall be presented to ETA Danmark on request Initial type testing of the product or initial type testing the results of the tests performed as part of the assessment for the European Technical Approval shall be used unless there are changes in the production line or plant. In such cases the necessary initial type testing has to be agreed between the approval body issuing the ETA and the notified body. The initial type testing shall be subject to the following checks: - Raw material specification; - Dimension of the inserts; - Characteristic withdrawal parameter f ax,k ; - Characteristic head pull-through parameter f head,k ; - Characteristic tensile strength f tens,k ; - Characteristic yield strength if relevant; - Characteristic torsional strength f tor,k ; - Characteristic insertion moment R tor,k ; - Durability. 4 The control plan has been deposited at ETA-Danmark and is only made available to the approved bodies involved in the conformity attestation procedure.

8 Tasks of notified bodies Page 8 of 12 of European Technical Approval no. ETA-12/ Initial inspection of the factory and the factory production control The approved body should ascertain that, in accordance with the control plan, the factory, in particular the staff and equipment, and the factory production control, are suitable to ensure a continuous and orderly manufacturing of the screws with the specifications given in part Continuous surveillance The approved body shall visit the factory at least twice a year for routine inspections. It shall be verified that the system of factory production control and the specified manufacturing processes are maintained, taking account of the control plan. The results of product certification and continuous surveillance shall be made available on demand by the certification body to ETA Danmark. Where the provisions of the European Technical Approval and the control plan are no longer fulfilled, the certificate of conformity shall be withdrawn by the approved body. 3.3 CE marking The CE marking shall be affixed on each packaging of screws. The initials "CE" shall be followed by the identification number of the notified body and shall be accompanied by the following information: - Name or identifying mark of the manufacturer - The last two digits of the year in which the marking was affixed - Number of the European Technical Approval - Name of product - Outer thread diameter and length of the self-tapping screws - Type and mean thickness of the corrosion protection - Stainless steel including the material number - Reaction to fire - Number of the EC Certificate of Conformity

9 Page 9 of 12 of European Technical Approval no. ETA-12/ Assumptions under which the fitness of the product for the intended use was favourably assessed 4.1 Manufacturing The inserts are manufactured in accordance with the provisions of the European Technical Approval using the automated manufacturing process as identified during the inspection of the plant by the approval body issuing the ETA and the approved body and laid down in the technical documentation. 4.2 Installation The installation shall be carried out in accordance with Eurocode 5 or an appropriate national code unless otherwise is defined in the following. Instructions from Hans Brügmann GmbH & Co. KG should be considered for installation The inserts are used for connections in load bearing timber structures between members of solid timber (softwood), glued laminated timber, cross-laminated timber, and laminated veneer lumber, similar glued members, woodbased panels or steel members. The inserts may be used for connections in load bearing timber structures with structural members according to an associated European Technical Approval, if according to the associated European Technical Approval of the structural member a connection in load bearing timber structures with screws according to a European Technical Approval is allowed. A minimum of two inserts should in general be used for connections in load bearing timber structures. The minimum penetration depth in structural members made of solid, glued or cross-laminated timber is 3 d. Wood-based panels and steel plates should only be arranged on the side of the metric bolt head. The minimum thickness of wood-based panels should be 1,2 d. or structural members according to European Technical Approvals the terms of the European Technical Approvals must be considered. The minimum angle between the screw axis and the grain direction is α = The screws shall be driven into the wood with predrilling. The maximum pre-drilling diameter is the inner thread diameter. The hole diameter in steel members must be predrilled with a suitable diameter. Only the equipment prescribed by Hans Brügmann GmbH & Co. KG shall be used for driving the screws or structural timber members, minimum spacing and distances for inserts in predrilled holes are given in EN :2008 (Eurocode 5) clause and table 8.2 as for nails in predrilled holes. Here, the outer thread diameter d must be considered. Minimum distances and spacing for inserts in the plane surface of cross laminated timber members with a minimum thickness t = 10 d may be taken as (see Annex B): Spacing a 1 parallel to the grain a 1 = 4 d Spacing a 2 perpendicular to the grain a 2 = 2,5 d Distance a 3,c from centre of the screw-part in timber to the unloaded end grain a 3,c = 6 d Distance a 3,t from centre of the screw-part in timber to the loaded end grain a 3,t = 6 d Distance a 4,c from centre of the screw-part in timber to the unloaded edge a 4,c = 2,5 d Distance a 4,t from centre of the screw-part in timber to the loaded edge a 4,t = 6 d Minimum distances and spacing for inserts in the edge surface of cross laminated timber members with a minimum thickness t = 10 d and a minimum penetration depth perpendicular to the edge surface may be taken as (see Annex B): Spacing a 1 parallel to the CLT plane a 1 = 10 d Spacing a 2 perpendicular to the CLT plane a 2 = 4 d Distance a 3,c from centre of the screw-part in timber to the unloaded end a 3,c = 7 d Distance a 3,t from centre of the screw-part in timber to the loaded end a 3,t = 12 d Distance a 4,c from centre of the screw-part in timber to the unloaded edge a 4,c = 3 d Distance a 4,t from centre of the screw-part in timber to the loaded edge a 4,t = 6 d Minimum distances and spacing for RAMPA screws in cross laminated timber are given in Annex B. 4.3 Maintenance and repair Maintenance is not required during the assumed intended working life. Should repair prove necessary, it is normal to replace the insert. Thomas Bruun Manager, ETA-Danmark

10 Page 10 of 12 of European Technical Approval no. ETA-12/0481 Annex A Drawings of RAMPA inserts Table A.1: Installation parameters Insert size M4 M5 M6 M8 M10 M12 M16 Drill hole diameter in timber d 1 = [mm] Minimum screw-in depth in the insert L min = [mm] Additional installation parameters: Minimum depth of drill hole in timber = L Available thread length in the insert = L 2 Requirements of the fastening screw or the threaded rod and nut according to the engineering documents: Steel, zinc-plated Property class 4.6 / 5.6 / 5.8 or 8.8 according to EN ISO or EN Stainless steel, A2 or A4 Material ; ; ; ; ; according to EN Property class 50, 70 or 80 according to EN ISO 3506

11 Page 11 of 12 of European Technical Approval no. ETA-12/0481 Table A.2: Installation parameters Insert size M6 M8 M10 M12 M16 Drill hole diameter in timber d 1 =[mm] Minimum screw-in depth in the insert L min =[mm] Additional installation parameters: Minimum depth of drill hole in timber = L Available thread length in the insert = L 2 Requirements of the fastening screw or the threaded rod and nut according to the engineering documents: Steel, zinc-plated Property class 4.6 / 5.6 / 5.8 or 8.8 according to EN ISO or EN Stainless steel, A2 or A4 Material ; ; ; ; ; according to EN Property class 50, 70 or 80 according to EN ISO 3506

12 Page 12 of 12 of European Technical Approval no. ETA-12/0481 Annex B Minimum distances and spacing Axially or laterally loaded screws in the plane or edge surface of cross laminated timber Definition of spacing, end and edge distances in the plane surface: a1 a2 a2 a2 a1,t a1,c a2,c α α α a2,t Definition of spacing, end and edge distances in the edge surface: a2,c a2,c a2,c a2,t a1,t a1,c a1 a1 a1,c a1,c ti ti tclt tclt Minimum spacing, end and edge distances of inserts in the plane or edge surfaces of cross laminated timber Plane surface Edge surface a1 4 d 10 d a1,t 6 d 12 d a1,c 6 d 7 d a2 2,5 d 4 d a2,t 6 d 6 d a2,c 2,5 d 3 d