HUS-HR, CR Screw anchor, stainless steel

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "HUS-HR, CR Screw anchor, stainless steel"

Transcription

1 HUS-HR, CR Screw anchor, Anchor version HUS-HR 6 / 8 / 10 / 14 Stainless steel concrete Screw with hexagonal head HUS-CR 10 Stainless steel concrete screw with countersunk head Benefits - High productivity less drilling and fewer operations than with conventional anchors - ETA approval for cracked and non-cracked concrete - Seismic approval ETA C1 - Small edge and spacing distances Concrete Tensile zone Solid brick Autoclaved aerated concrete Seismic ETA-C1 Small edge distance and spacing Fire resistance Corrosion Resistance Sprinkler approved European Technical Approval CE conformity PROFIS Anchor design software Approvals / certificates Description Authority / Laboratory No, / date of issue European technical approval a) DIBt, Berlin ETA-08/0307 / Fire test report DIBt, Berlin ETA-08/0307 / Fire test report ZTV Tunnel (EBA) MFPA, Leipzig PB III / / a) Data for HUS-HR with standard and reduced embedment depth is given in this section according ETA-08/0307 issue , Basic loading data All data in this section applies to - Correct setting (See setting instruction) - No edge distance and spacing influence - Concrete as specified in the table - Steel failure - Minimum base material thickness - Concrete C 20/25, f ck,cube = 25 N/mm² For details see Simplified design method 252

2 Mean ultimate resistance Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Tensile N Ru,m [kn] - a) 12,0 16,0 - - a) 6,7 10,0 - Shear V Ru,m [kn] - a) 31,5 41,9 - - a) 22,5 30,0 - Reduced embedment (ETA-08/0307) Tensile N Ru,m [kn] - 16,0 21,3 25,2-8,0 12,0 16,0 Shear V Ru,m [kn] - 34,7 44,0 50,4-30,9 38,1 36,0 Standard embedment (ETA-08/0307) Tensile N Ru,m [kn] 12,0 21,3 33,3 53,6 6,7 16,0 21,3 33,3 Shear V Ru,m [kn] 22,7 34,7 44,0 102,7 21,7 34,7 44,0 76,6 a) Please refer to resistance table in all load directions for multiple use fastenings in section HUS 6 screw anchor for redundant fastening, Characteristic resistance Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Tensile N Rk [kn] - a) 9,0 12,0 - - a) 5,0 7,5 - Shear V Rk [kn] - a) 23,6 31,4 - - a) 16,9 22,5 - Reduced embedment (ETA-08/0307) Tensile N Rk [kn] - 12,0 16,0 18,9-6,0 9,0 12,0 Shear V Rk [kn] - 26,0 33,0 37,8-23,2 28,6 27,0 Standard embedment (ETA-08/0307) Tensile N Rk [kn] 9,0 16,0 25,0 40,2 5,0 12,0 16,0 25,0 Shear V Rk [kn] 17,0 26,0 33,0 77,0 16,3 26,0 33,0 57,4 a) Please refer to resistance table in all load directions for multiple use fastenings in section HUS 6 screw anchor for redundant fastening, 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

3 Design resistance Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Tensile N Rd [kn] - a) 5,0 6,7 - - a) 2,8 4,2 - Shear V Rd [kn] - a) 15,7 21,0 - - a) 11,2 15,0 - Reduced embedment (ETA-08/0307) Tensile N Rd [kn] - 6,7 8,9 10,5-3,3 5,0 6,7 Shear V Rd [kn] - 17,3 22,0 25,2-15,5 19,0 18,0 Standard embedment (ETA-08/0307) Tensile N Rd [kn] 4,3 8,9 13,9 22,3 2,4 6,7 8,9 13,9 Shear V Rd [kn] 11,3 17,3 22,0 51,3 10,9 17,3 22,0 38,3 a) Please refer to resistance table in all load directions for multiple use fastenings in section HUS 6 screw anchor for redundant fastening, Recommended loads Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Tensile N a) rec [kn] - b) 3,6 4,8 - - b) 2,0 3,0 - a) Shear V rec [kn] - b) 11,2 15,0 - - b) 8,0 10,7 - Reduced embedment (ETA-08/0307) a) Tensile N rec [kn] - 4,8 6,3 7,5-2,4 3,6 4,8 a) Shear V rec [kn] - 12,4 15,7 18,0-11,0 13,6 12,9 Standard embedment (ETA-08/0307) a) Tensile N rec [kn] 3,1 6,3 9,9 16,0 1,7 4,8 6,3 9,9 a) Shear V rec [kn] 8,1 12,4 15,7 36,7 7,8 12,4 15,7 27,3 a) With overall partial safety factor for action = 1,4, The partial safety factors for action depend on the type of loading and shall be taken from national regulations, b) Please refer to resistance table in all load directions for multiple use fastenings in section HUS 6 screw anchor for redundant fastening, 254

4 Materials Mechanical properties Anchor size Type HUS-HR HUS-HR HUS-HR,CR HUS-HR Nominal tensile strength f uk [N/mm²] Nominal yield strength f y k [N/mm²] Stressed cross-section A s [mm²] 22,9 39,0 55,4 143,1 Moment of resistance W [mm³] Design bending resistance M Rd,s [Nm] Part Stainless steel hexagonal head concrete screw Material Stainless steel (grade A4) Anchor dimensions Dimensions Anchor version d s [mm] d k [mm] A s [mm 2 ] HUS-HR 6 7,6 5,4 22,9 HUS-HR 8 10,1 7,05 39,0 HUS-HR 10 12,3 8,40 55,4 HUS-CR 10 12,3 8,40 55,4 HUS-HR 14 16,6 12,6 143,1 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

5 Screw length and thickness of fixture for HUS-HR (hex head) Anchor size HUS HR h nom h nom h nom h nom h nom h nom h nom h nom h nom Nominal anchorage depth [mm] Length of anchor [mm] h nom 110 Thickness of fixture [mm] t fix1 t fix2 t fix1 t fix2 t fix3 t fix1 t fix2 t fix3 t fix1 t fix Screw length and thickness of fixture for HUS-CR (countersunk head) Anchor size HUS HR 10 h nom h nom h nom Nominal anchorage depth [mm] Thickness of fixture [mm] Length of anchor [mm] t fix1 t fix2 t fix

6 Setting Recommended installation equipment Anchor size HUS Rotary hammer Hilti TE 2 TE 30 Hilti TE 2 TE 30 Hilti TE 2 TE 30 Hilti TE 2 TE 30 drill bit TE-C3X 6/17 TE-C3X 8/17 TE-C3X 10/22 TE-C3X 14/22 Socket wrench insert S-NSD 13 ½ (L) S-NSD 13 ½ (L) S-NSD 15 ½ (L) S-NSD 21 ½ Torx (CR type only) - - S-SY TX50 - Impact screw driver Hilti SIW 14-A, 22-A Hilti SIW 22 T-A Setting instruction For detailed information on installation see instruction for use given with the package of the product, Setting details: depth of drill hole h 1 and effective anchorage depth h ef 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

7 Setting details Anchor version Type HUS HR HR HR, CR a) HR Nominal embedment depth h nom [mm] Nominal diameter of drill bit d o [mm] Cutting diameter of drill bit d cut [mm] 6,4 8,45 10,45 14,5 Depth of drill hole h 1 [mm] Diameter of countersunk head d h [mm] Diameter of clearance hole in the d fixture f [mm] Effective anchorage depth h ef [mm] Max, installation torque Concrete T inst [Nm] 20 - a) 35 - a) - a) 45 c) 65 Solid m, Mz 12 T inst [Nm] - b) 10 - b) b) - b) Solid m, KS 12 T inst [Nm] - b) 10 - b) b) - b) Aerated conc, T inst [Nm] - b) 4 - b) b) - b) a) Hilti recommends machine setting only in concrete b) Hilti does not recommend this setting process for this application, c) Intallation torque refer to HUS-HR only Base material thickness, anchor spacing and edge distance Anchor size Type HUS-HR HUS-HR HUS-HR, CR HUS-HR Nominal embedment depth Minimum base material thickness non-cracked concrete h nom [mm] h min [mm] Minimum spacing s min [mm] Minimum edge distance Critical spacing for concrete cone and splitting failure Critical edge distance for concrete cone and splitting failure c min [mm] s cr,n = s cr,sp c cr,n = c cr,sp [mm] [mm] For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be reduced (see system design resistance), Critical spacing and critical edge distance for splitting failure apply only for non-cracked concrete, For cracked concrete only the critical spacing and critical edge distance for concrete cone failure are decisive, 258

8 Simplified design method Simplified version of the design method according ETAG 001, Annex C, Design resistance according data given in ETA-08/0307 issue 2011,01,21, Influence of concrete strength Influence of edge distance Influence of spacing Valid for a group of two anchors, (The method may also be applied for anchor groups with more than two anchors or more than one edge, The influencing factors must then be considered for each edge distance and spacing, The calculated design loads are then on the save side: They will be lower than the exact values according ETAG 001, Annex C, To avoid this, it is recommended to use the anchor design software PROFIS anchor) The design method is based on the following simplification: No different loads are acting on individual anchors (no eccentricity) The values are valid for one anchor (single point fastening), multiple use applications are not part of this design method, For more complex fastening applications please use the anchor design software PROFIS Anchor, Tension loading The design tensile resistance is the lower value of - Steel resistance: N Rd,s - Concrete pull-out resistance: N Rd,p = N 0 Rd,p f B - Concrete cone resistance: N Rd,c = N 0 Rd,c f B f 1,N f 2,N f 3,N f re,n - Concrete splitting resistance (only non-cracked concrete): N Rd,sp = N 0 Rd,c f B f 1,sp f 2,sp f 3,sp f re,n Basic design tensile resistance Design steel resistance N Rd,s Anchor size Type HUS-HR HUS-HR HUS-HR, CR HUS-HR N Rd,s [kn] 17,0 24,3 37,6 73,0 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

9 Design pull-out resistance N Rd,p = N 0 Rd,p f B Extra reduced embedment (Hilti Tech Data) Tensile N Rd [kn] - 5,0 6, ,8 4,2 - Reduced embedment Tensile N Rd [kn] - 6,7 8,9 10,5-3,3 5,0 6,7 Standard embedment Tensile N Rd [kn] 4,3 8,9 13,9 22,3 2,4 6,7 8,9 13,9 Design concrete cone N Rd,c = N 0 Rd,c f B f 1,N f 2,N f 3,N f re,n Design splitting resistance* N Rd,sp = N 0 Rd,c f B f 1,sp f 2,sp f 3,sp f re,n Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) N 0 Rd,c [kn] - 6,6 8, ,7 6,2 - Reduced embedment N 0 Rd,c [kn] - 9,0 11,1 10,5-6,4 7,9 7,5 Standard embedment N 0 Rd,c [kn] 7,2 14,3 16,8 22,3 5,2 10,2 12,0 16,0 a) Splitting resistance must only be considered for non-cracked concrete ETA: Data according ETA-08/0307 issue Hilti: Additional Hilti technical data Influencing factors Influence of concrete strength Concrete strength designation (ENV 206) C 20/25 C 25/30 C 30/37 C 35/45 C 40/50 C 45/55 C 50/60 f B = (f ck,cube /25N/mm²) 0,5 a) 1 1,1 1,22 1,34 1,41 1,48 1,55 a) f ck,cube = concrete compressive strength, measured on cubes with 150 mm side length 260

10 Influence of edge distance a) c/c cr,n c/c cr,sp f 1,N = 0,7 + 0,3 c/c cr,n 1 f 1,sp = 0,7 + 0,3 c/c cr,sp 1 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,73 0,76 0,79 0,82 0,85 0,88 0,91 0,94 0,97 1 f 2,N = 0,5 (1 + c/c cr,n ) 1 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1 f 2,sp = 0,5 (1 + c/c cr,sp ) 1 a) The edge distance shall not be smaller than the minimum edge distance c min given in the table with the setting details, These influencing factors must be considered for every edge distance, Influence of anchor spacing a) s/s cr,n s/s cr,sp 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 f 3,N = 0,5 (1 + s/s cr,n ) 1 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1 f 3,sp = 0,5 (1 + s/s cr,sp ) 1 a) The anchor spacing shall not be smaller than the minimum anchor spacing s min given in the table with the setting details, This influencing factor must be considered for every anchor spacing, Influence of base material thickness h/h ef 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,68 f h,sp = [h/(2 h ef )] 2/3 1 1,07 1,13 1,19 1,25 1,31 1,37 1,42 1,48 1,5 Influence of reinforcement Anchor size Type HUS HR HR HR, CR HR h nom [mm] h ef [mm] f re,n = 0,5 + h ef /200mm 1 0,62 0,73 0,69 0,74 0,82 0,73 0,77 0,86 0,76 0,93 a) This factor applies only for dense reinforcement, If in the area of anchorage there is reinforcement with a spacing 150 mm (any diameter) or with a diameter 10 mm and a spacing 100 mm, then a factor f re,n = 1 may be applied, Shear loading The design shear resistance is the lower value of - Steel resistance: V Rd,s - Concrete pryout resistance: V Rd,cp = k N Rd,c - Concrete edge resistance: V Rd,c = V 0 Rd,c f B f ß f h f 4 f hef f c 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

11 Basic design shear resistance Design steel resistance V Rd,s Anchor size Type HUS HR HR HR, CR HR Extra reduced embedment V Rd,s [kn] 11,3 17,3 22,0 - Reduced embedment V Rd,s [kn] - 17,3 22,0 36,7 Standard embedment V Rd,s [kn] 11,3 17,3 22,0 51,3 Design concrete pryout resistance V Rd,cp = k N Rd,c a) Anchor size Type HUS HR HR HR, CR HR h nom [mm] k 1,0 1,5 2,0 a) N Rd,c : Design concrete cone resistance Design concrete edge resistance V Rd,c = V 0 Rd,c f B f ß f h f 4 f hef f c Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) V 0 Rd,c [kn] - 5,9 8, ,2 6,1 - Reduced embedment V 0 Rd,c [kn] - 5,9 8,6 15-4,2 6,1 10,6 Standard embedment V 0 Rd,c [kn] 3,6 5,9 8,6 15,1 2,6 4,2 6,1 10,7 Influencing factors Influence of concrete strength Concrete strength designation (ENV 206) C 20/25 C 25/30 C 30/37 C 35/45 C 40/50 C 45/55 C 50/60 f B = (f ck,cube /25N/mm²) 0,5 a) 1 1,1 1,22 1,34 1,41 1,48 1,55 a) f ck,cube = concrete compressive strength, measured on cubes with 150 mm side length 262

12 Influence of angle between load applied and the direction perpendicular to the free edge Angle ß f cos V sin V 2,5 1 1,01 1,05 1,13 1,24 1,40 1,64 1,97 2,32 2,50 Influence of base material thickness h/c 0,15 0,3 0,45 0,6 0,75 0,9 1,05 1,2 1,35 1,5 f h = {h/(1,5 c)} 1/2 1 0,32 0,45 0,55 0,63 0,71 0,77 0,84 0,89 0,95 1,00 Influence of anchor spacing and edge distance a) for concrete edge resistance: f 4 c/h ef Single anchor Group of two anchors s/h ef 0,75 1,50 2,25 3,00 3,75 4,50 5,25 6,00 6,75 7,50 8,25 9,00 9,75 10,50 11,25 0,50 0,35 0,27 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,75 0,65 0,43 0,54 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 1,00 1,00 0,63 0,75 0,88 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,25 1,40 0,84 0,98 1,12 1,26 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,50 1,84 1,07 1,22 1,38 1,53 1,68 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,75 2,32 1,32 1,49 1,65 1,82 1,98 2,15 2,32 2,32 2,32 2,32 2,32 2,32 2,32 2,32 2,32 2,00 2,83 1,59 1,77 1,94 2,12 2,30 2,47 2,65 2,83 2,83 2,83 2,83 2,83 2,83 2,83 2,83 2,25 3,38 1,88 2,06 2,25 2,44 2,63 2,81 3,00 3,19 3,38 3,38 3,38 3,38 3,38 3,38 3,38 2,50 3,95 2,17 2,37 2,57 2,77 2,96 3,16 3,36 3,56 3,76 3,95 3,95 3,95 3,95 3,95 3,95 2,75 4,56 2,49 2,69 2,90 3,11 3,32 3,52 3,73 3,94 4,15 4,35 4,56 4,56 4,56 4,56 4,56 3,00 5,20 2,81 3,03 3,25 3,46 3,68 3,90 4,11 4,33 4,55 4,76 4,98 5,20 5,20 5,20 5,20 3,25 5,86 3,15 3,38 3,61 3,83 4,06 4,28 4,51 4,73 4,96 5,18 5,41 5,63 5,86 5,86 5,86 3,50 6,55 3,51 3,74 3,98 4,21 4,44 4,68 4,91 5,14 5,38 5,61 5,85 6,08 6,31 6,55 6,55 3,75 7,26 3,87 4,12 4,36 4,60 4,84 5,08 5,33 5,57 5,81 6,05 6,29 6,54 6,78 7,02 7,26 4,00 8,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00 6,25 6,50 6,75 7,00 7,25 7,50 7,75 4,25 8,76 4,64 4,90 5,15 5,41 5,67 5,93 6,18 6,44 6,70 6,96 7,22 7,47 7,73 7,99 8,25 4,50 9,55 5,04 5,30 5,57 5,83 6,10 6,36 6,63 6,89 7,16 7,42 7,69 7,95 8,22 8,49 8,75 4,75 10,35 5,45 5,72 5,99 6,27 6,54 6,81 7,08 7,36 7,63 7,90 8,17 8,45 8,72 8,99 9,26 5,00 11,18 5,87 6,15 6,43 6,71 6,99 7,27 7,55 7,83 8,11 8,39 8,66 8,94 9,22 9,50 9,78 5,25 12,03 6,30 6,59 6,87 7,16 7,45 7,73 8,02 8,31 8,59 8,88 9,17 9,45 9,74 10,02 10,31 5,50 12,90 6,74 7,04 7,33 7,62 7,92 8,21 8,50 8,79 9,09 9,38 9,67 9,97 10,26 10,55 10,85 a) The anchor spacing and the edge distance shall not be smaller than the minimum anchor spacing s min and the minimum edge distance c min, Influence of embedment depth Anchor size Type HUS HR HR HR, CR HR h nom [mm] f hef = 0,05 (h ef / d) 1,68-1,48 0,69 0,98 1,64 0,65 0,85 1,35 0,45 1,06 Influence of edge distance a) c/d f c = (d / c) 0,19 0,77 0,71 0,67 0,65 0,60 0,57 0,52 0,50 a) The edge distance shall not be smaller than the minimum edge distance c min, 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

13 Combined tension and shear loading For combined tension and shear loading see section Anchor Design, Precalculated values Design resistance calculated according ETAG 001, Annex C and data given in ETA-08/0307, issue 2011,01,21, All data applies to concrete C 20/25 f ck,cube =25 N/mm², Hilti technical data for the extra reduced embedment depth is not part of the approval, Recommended loads can be calculated by dividing the design resistance by an overall partial safety factor for action = 1,4, The partial safety factors for action depend on the type of loading and shall be taken from national regulations, Design resistance Single anchor, no edge effects (c c cr ), shear without lever arm Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Min, base material thickness h min [mm] Tensile N Rd [kn] - 5,0 6, ,8 4,2 - Shear V Rd [kn] - 15,7 21, ,2 15,0 - Reduced embedment Min, base material thickness h min [mm] Tensile N Rd [kn] - 6,7 8,9 10,5-3,3 5,0 6,7 Shear V Rd [kn] - 17,3 22,0 25,2-15,5 19,0 18,0 Standard embedment Min, base material thickness h min [mm] Tensile N Rd [kn] 4,3 8,9 13,9 22,3 2,4 6,7 8,9 13,9 Shear V Rd [kn] 11,3 17,3 22,0 51,3 10,9 17,3 22,0 38,3 264

14 Single anchor, min, edge distance (c = c min ), shear without lever arm Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Min, base material thickness h min [mm] Min, edge distance c min [mm] Tensile N Rd [kn] - 5,0 6, ,8 4,2 - Shear V Rd [kn] - 3,8 4, ,7 3,3 - Reduced embedment Min, base material thickness h min [mm] Min, edge distance c min [mm] Tensile N Rd [kn] - 6,6 8,0 7,7-3,3 5,0 4,9 Shear V Rd [kn] - 3,9 4,8 5,0-2,8 3,4 3,6 Standard embedment Min, base material thickness h min [mm] Min, edge distance c min [mm] Tensile N Rd [kn] 4,3 8,9 10,4 13,8 2,4 6,7 6,8 9,0 Shear V Rd [kn] 3,2 4,8 5,1 7,1 2,2 3,4 3,6 5,0 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

15 Double anchor, no edge effects (c c cr ), min, spacing (s = s min ), shear without lever arm (load values are valid for one anchor) Type HUS HR HR HR,CR HR HR HR HR,CR HR Extra reduced embedment (Hilti Tech Data) Min, base material thickness h min [mm] Min, spacing s min [mm] Tensile N Rd [kn] - 4,6 6, ,3 4,3 - Shear V Rd [kn] - 11,0 14, ,8 10,2 - Reduced embedment Min, base material thickness h min [mm] Min, spacing s min [mm] Tensile N Rd [kn] - 6,0 7,3 6,9-4,3 5,2 5,0 Shear V Rd [kn] - 14,3 17,5 16,7-10,2 12,5 11,9 Standard embedment Min, base material thickness h min [mm] Min, spacing s min [mm] Tensile N Rd [kn] 4,7 9,1 10,4 13,8 3,4 6,5 7,4 9,8 Shear V Rd [kn] 9,9 17,3 22,0 33,1 7,0 15,5 17,7 23,6 266

16 Fire resistance Basic loading data for concrete C20/25 C50/60 All data in this section applies to: - Correct setting (see setting instruction) - No edge distance and spacing influence - Minimum base material thickness The following technical data are based on: ETA-08/0307 issue Characteristic loads under fire exposure Anchor Size Type HUS HR HR HR, CR HR, CR h nom h nom h nom h nom h nom h nom h nom Nominal embedment depth h nom [mm] Steel failure for tension and shear load (F Rec,s,fi = N Rec,s,fi = V Rec,s,fi ) Recommended tensile and shear load Pull out failure Recommended resistance R30 F Rec,s,fi [kn] 2,3 4,4 8,8 19,9 R60 F Rec,s,fi [kn] 1,6 3,0 5,7 12,8 R90 F Rec,s,fi [kn] 0,9 1,5 2,6 5,8 R120 F Rec,s,fi [kn] 0,5 0,8 1,1 2,6 R30 M 0 Rec,s,fi [Nm] 1,9 3,9 9,2 31,2 R60 M 0 Rec,s,fi [Nm] 1,3 2,6 6,0 20,2 R90 M 0 Rec,s,fi [Nm] 0,7 1,3 2,7 9,1 R120 M 0 Rec,s,fi [Nm] 0,4 0,7 1,2 4,0 R30 R60 R90 Concrete cone failure Edge distance N Rec,p,fi [kn] 0,6 0,7 1,4 1,1 1,9 1,4 3,0 R120 N Rec,p,fi [kn] 0,5 0,6 1,1 0,9 1,5 1,1 2,4 Spacing R30 to R120 c cr,n [mm] 2h ef R30 to R120 s cr,n [mm] 4h ef Concrete pry-out failure R30 to R120 k [-] 1,5 2,0 2,0 2,0 b) gthe recommended loads under fire exposure include a safety factor for resistance under fire exposure M,fi = 1,0 and the partial safety factor for action F,fi = 1,0, The partial safety factors for action shall be taken from national regulations, 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

17 Seismic design Basic loading data for concrete C20/25 C50/60 All data in this section applies to: - Seismic design according to TR045 The following technical data are based on: ETA-08/0307 issue Anchorage depth range Anchor size Type HUS HR HR, CR HR Nominal anchorage depth range h nom [mm] Tension resistance in case of seismic performance category C1 Anchor size Type HUS HR HR, CR HR Characteristic tension resistance to steel failure N Rk,s,seis [kn] 34,0 52,6 102,2 Partial safety factor Ms,seis [-] 1,4 Characteristic pull-out resistance in cracked concrete C20/25 to C50/60 N Rk,p,seis [kn] 7,7 12,5 17,5 Partial safety factor Mp,seis [-] 1,8 Concrete cone resistance and splitting resistance Partial safety factor Mc,seis = Msp,seis [-] 1,8 Displacement under tension load in case of seismic performance category C1 1) Anchor size Type HUS HR HR, CR HR Displacement N,seis [mm] 1,2 1,2 0,4 1) Maximum displacement during cycling (seismic event), Shear resistance in case of seismic performance category C1 1) Anchor size Type HUS HR HR, CR HR Characteristic shear resistance to steel failure V Rk,s,seis [kn] 11,1 17,9 53,9 Partial safety factor Ms,seis [-] 1,5 Concrete pryout resistance and concrete edge resistance Partial safety factor Mc,seis [-] 1,5 1) Reduction factor gap = 1,0 when using the Hilti Dynamic Set Displacement under tension load in case of seismic performance category C1 1) Anchor size Type HUS HR HR, CR HR Displacement V,seis [mm] 4,8 5,3 7,6 1) Maximum displacement during cycling (seismic event) 268

18 Basic loading data for single anchor in solid masonry units All data in this section applies to - Load values valid for holes drilled with TE rotary hammers in hammering mod - Correct anchor setting (see instruction for use, setting details) - The core / material ratio may not exceed 15% of a bed joint area, - The brim area around holes must be at least 70mm - Edge distances, spacing and other influences, see below Recommended loads Hilti Base material Anchor size Type 6 HUS-HR 8 HUS-HR 10 HUS-HR, CR Germany, Austria, Switzerland h nom [mm] Solid clay brick Mz12/2,0 DIN 105/ EN f b a) 12 N/mm² Tensile N rec [kn] 0,9 1,0 1,1 Shear V rec [kn] 1,4 2,0 2,3 Solid sand-lime brick KS 12/2,0 DIN 106/ EN a) f b 12 N/mm² Tensile N rec Shear V rec [kn] [kn] 0,6 0,6 1,0 0,9 1,1 1,7 Aerated concrete PPW 6-0,4 DIN 4165/ EN f b a) 6 N/mm² Tensile N rec Shear V rec [kn] [kn] 0,2 0,2 0,4 0,4 0,4 0,9 a) f b = brick strength 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

19 Permissible anchor location in brick and block walls Edge distance and spacing influences The technical data for the HUS-HR anchors are reference loads for MZ 12 and KS 12, Due to the large variation of natural stone solid bricks, on site anchor testing is recommended to validate technical data, The HUS-HR anchor was installed and tested in center of solid bricks as shown, The HUS-HR anchor was not tested in the mortar joint between solid bricks or in hollow bricks; however a load reduction is expected, For brick walls where anchor position in brick can not be determined, 100% anchor testing is recommended, Distance to free edge free edge to solid masonry (Mz and KS) units 200 mm Distance to free edge free edge to solid masonry (autoclaved aerated gas concrete) units 170 mm The minimum distance to horizontal and vertical mortar joint (c min ) is stated in drawing above, Minimum anchor spacing (s min ) in one brick/block is 2*c min Limits Applied load to individual bricks may not exceed 1,0 kn without compression or 1,4 kn with compression All data is for multiple use for non structural applications Plaster, graveling, lining or levelling courses are regarded as non-bearing and may not be taken into account for the calculation of embedment depth, 270

HVU with HAS/HAS-E rod adhesive anchor

HVU with HAS/HAS-E rod adhesive anchor HVU with HAS/HAS-E rod HVU with HAS/HAS-E rod adhesive anchor Mortar system Benefits Hilti HVU foil capsule HAS HAS-R HAS-HCR rod - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity

More information

EUROPEAN ORGANISATION FOR TECHNICAL APPROVALS

EUROPEAN ORGANISATION FOR TECHNICAL APPROVALS E TA TECHNICAL REPORT Design of Bonded Anchors TR 29 Edition June 27 EUROPEAN ORGANISATION FOR TECHNICAL APPROVALS TABLE OF CONTENTS Design method for bonded anchors Introduction..4 1 Scope...2 1.1 Type

More information

English translation prepared by DIBt Original version in German language

English translation prepared by DIBt Original version in German language Date: Reference: 14.05.2013 I 22-1.21.1-87/12 (73/13) English translation prepared by DIBt Original version in German language Approval number: Validity Z-21.1-1987 from: 14 May 2013 Applicant: Hilti Deutschland

More information

(English language translation, the original version is in French language) Injection system Hilti HIT-HY 150 MAX

(English language translation, the original version is in French language) Injection system Hilti HIT-HY 150 MAX Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 Autorisé et notifié conformément

More information

Bonded Anchors & Mechanical Anchors

Bonded Anchors & Mechanical Anchors Bonded Anchors & Mechanical Anchors 1980 s and R-HPT mechanical anchors 2007 1887-1897 RAWLINGS BROTHERS started out in London 1912 RAWLPLUG Trademark registration 1919 Rawlings Brothers THE RAWLPLUG COMPANY

More information

European Technical Assessment. ETA-02/0020 of 22 September 2015. English translation prepared by DIBt - Original version in German language

European Technical Assessment. ETA-02/0020 of 22 September 2015. English translation prepared by DIBt - Original version in German language European Technical Assessment ETA-02/0020 of 22 September 2015 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the

More information

Ermächtigt u n d n o t i f i z i e r t gemäß Artikel 10 der Richtlinie des Rates vom 21. Dezember 1988 zur Angleichung

Ermächtigt u n d n o t i f i z i e r t gemäß Artikel 10 der Richtlinie des Rates vom 21. Dezember 1988 zur Angleichung Zavod za gradbeništvo Slovenije Slovenian National Building and Civil Engineering Institute Dimičeva 12, 1000 Ljubljana, Slovenija Tel.: +386 (0)1-280 44 72 Fax: +386 (0)1-436 74 49 e-mail: info.ta@zag.si

More information

DIVISION: 04 00 00 MASONRY SECTION: 04 05 19.16 MASONRY ANCHORS REPORT HOLDER: HILTI, INC. 7250 DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: 04 00 00 MASONRY SECTION: 04 05 19.16 MASONRY ANCHORS REPORT HOLDER: HILTI, INC. 7250 DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3342 Reissued 08/2015 This report is subject to renewal 08/2017. DIVISION: 04 00 00 MASONRY

More information

LOAD-CARRYING CAPACITY OF AXIALLY LOADED RODS GLUED-IN PERPENDICULAR TO THE GRAIN

LOAD-CARRYING CAPACITY OF AXIALLY LOADED RODS GLUED-IN PERPENDICULAR TO THE GRAIN LOAD-CARRYING CAPACITY OF AXIALLY LOADED RODS GLUED-IN PERPENDICULAR TO TE GRAIN Prof. Dr.-Ing..J. Blaß, Dipl.-Ing. B. Laskewitz Universität Karlsruhe (T), Germany Abstract Glued-in rods have been used

More information

PC-Concrete Injectable Concrete Anchoring and Repair System

PC-Concrete Injectable Concrete Anchoring and Repair System PC-Concrete Injectable Concrete Anchoring and Repair System DESCRIPTION: PC-Concrete is a two component (1:1 ratio), 100% solids, high modulus, structural epoxy paste. PC-Concrete is a solvent free, no

More information

SMART PLUG TYPE BP AND LBP

SMART PLUG TYPE BP AND LBP SMART PLUG TYPE BP AND LBP PLUG + SCREW SMART wall plug BP with hex lag screw DIN 571 ETA-10/0392 SMPZS 8 x 70 8 x 80 8 x 90 12 x 60 8 x 100 8 x 120 8 x 140 8 x 160 10 x 80 10 x 100 10 x 120 14 x 70 10

More information

Technical Application Document. Hilti HIT-RE 500-SD

Technical Application Document. Hilti HIT-RE 500-SD Technical Application Document Technical Evaluation Report 3/10-649 Injection system for rebar connections Hilti HIT-RE 500-SD Subject to European Technical Approval ATE-09/0295 Holder of approval: HILTI

More information

Guidelines for Earthquake Bracing of Residential Water Heaters

Guidelines for Earthquake Bracing of Residential Water Heaters Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)

More information

European Technical Approval ETA-09/0040

European Technical Approval ETA-09/0040 European Technical Approval ETA-09/0040 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and

More information

Machine devices, jig devices

Machine devices, jig devices Machine devices, jig devices 853 K0697 Rolled thread studs DIN 6379 Material: Tempered steel. KIPP Rolled thread studs DIN 6379 Order No. D L B1 B2 Approx. weight g Surface finish: Thread rolled. Class

More information

PART E SPECIFICATIONS

PART E SPECIFICATIONS PART E SPECIFICATIONS Page 1 of 5 PART E - SPECIFICATIONS GENERAL E1. APPLICABLE SPECIFICATIONS, STANDARD DETAILS AND DRAWINGS E1.1 The City of Winnipeg Works and Operations Division Standard Construction

More information

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for electrical

More information

EJOT Spiralform. The thread formers for metal. EJOT The Quality Connection

EJOT Spiralform. The thread formers for metal. EJOT The Quality Connection EJOT Spiralform The thread formers for metal EJOT The Quality Connection Imprint Editor: EJOT GmbH & Co. KG Industrial Fasteners Division D 57319 Bad Berleburg Layout and Realisation: EJOT GmbH & Co. KG

More information

European Technical Approval ETA-11/0024

European Technical Approval ETA-11/0024 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

Hollow or Cinder Block Wall Mount Job Aid

Hollow or Cinder Block Wall Mount Job Aid Summary This Job Aid covers: Hollow or Cinder Block Wall Mount Job Aid Hollow or Cinder Block wall Mount Bracket Installing the Mount Bracket into Cinder Block This Job Aid supports the Technician audience.

More information

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900

More information

System. Stability. Security. Integrity. 150 Helical Anchor

System. Stability. Security. Integrity. 150 Helical Anchor Model 150 HELICAL ANCHOR System PN #MBHAT Stability. Security. Integrity. 150 Helical Anchor System About Foundation Supportworks is a network of the most experienced and knowledgeable foundation repair

More information

European Technical Approval ETA-10/0200

European Technical Approval ETA-10/0200 Deutsches Institut für Bautechnik Anstalt des öffentlichen Rechts Kolonnenstr. 30 B 10829 Berlin Germany Tel.: +49(0)30 787 30 0 Fax: +49(0)30 787 30 320 E-mail: dibt@dibt.de Internet: www.dibt.de Mitglied

More information

DE Frame with C Series Sidelight

DE Frame with C Series Sidelight TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder

More information

KIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices

KIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices 04000 Clamps Clamping devices 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 297 04010 Adjustable straps Tempered steel 1.1191 Black oxide finish nlm 04010-101 Suitable thrust

More information

PRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE. By H P Gupta & D K Gupta

PRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE. By H P Gupta & D K Gupta PRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE By H P Gupta & D K Gupta DIFFERENT TYPES OF DAMAGES 1.Minor cracks 0.5 to 5 mm wide in load or non-load bearing walls 2.Major

More information

Machine Screws, Dowel Pins and Hardware

Machine Screws, Dowel Pins and Hardware Machine Screws, Dowel Pins and Section Contents Plain Socket Head Screws...Page 13-2 Wire Locking Screws...Page 13-3 Captive Screws...Page 13- Ventilation Screws...Page 13- Shoulder Screws...Page 13-

More information

Report on. Wind Resistance of Signs supported by. Glass Fiber Reinforced Concrete (GFRC) Pillars

Report on. Wind Resistance of Signs supported by. Glass Fiber Reinforced Concrete (GFRC) Pillars Report on Wind Resistance of Signs supported by Glass Fiber Reinforced Concrete (GFRC) Pillars Prepared for US Sign and Fabrication Corporation January, 2006 SUMMARY This study found the attachment of

More information

DIVISION: 31 00 00 EARTHWORK SECTION: 31 63 00 BORED PILES REPORT HOLDER: HUBBELL POWER SYSTEMS, INC.

DIVISION: 31 00 00 EARTHWORK SECTION: 31 63 00 BORED PILES REPORT HOLDER: HUBBELL POWER SYSTEMS, INC. 0 ICC ES Report ICC ES (800) 4 6587 (56) 699 054 www.icc es.org 000 Most Widely Accepted and Trusted ESR 794 Reissued 05/05 This report is subject to renewal 05/06. DIVISION: 00 00 EARTHWORK SECTION: 6

More information

Lightweight aggregate concrete (LAC) Vertical coring reference bricks (Hlz) ÖNORM B 6124. Autoclaved aerated concrete P2 - P7

Lightweight aggregate concrete (LAC) Vertical coring reference bricks (Hlz) ÖNORM B 6124. Autoclaved aerated concrete P2 - P7 Anchor table ejotherm anchors with European Technical Approval (ETA) Fasteners for insulation boards Rail systems ejotherm ejotherm ejotherm ejotherm ejotherm ejotherm STR U STR H NT U NTK U SDK U NK U

More information

Connection Solutions

Connection Solutions Connection Solutions DESIGN BUILD SYSTEM Connection Solutions for Cold formed Steel Construction Complies with; AS/NZS 4600:2005 AISI S100:2007 AS/NZ 1397 ASTM A653 DESIGN & BUILD SYSTEM FRAMECAD Construction

More information

Design and Construction of Cantilevered Reinforced Concrete Structures

Design and Construction of Cantilevered Reinforced Concrete Structures Buildings Department Practice Note for Authorized Persons, Registered Structural Engineers and Registered Geotechnical Engineers APP-68 Design and Construction of Cantilevered Reinforced Concrete Structures

More information

The Stabilizer TM. Benefits. www.griptite.com. Supplemental support system for sagging beams and floor joists within a crawl space

The Stabilizer TM. Benefits. www.griptite.com. Supplemental support system for sagging beams and floor joists within a crawl space The Stabilizer TM Supplemental support system for sagging beams and floor joists within a crawl space Pre-drilled holes in steel plate allow for connection to beam or floor joists. Benefits Levels and

More information

THE DEVELOPMENT OF DESIGN METHODS FOR REINFORCED AND UNREINFORCED MASONRY BASEMENT WALLS J.J. ROBERTS

THE DEVELOPMENT OF DESIGN METHODS FOR REINFORCED AND UNREINFORCED MASONRY BASEMENT WALLS J.J. ROBERTS THE DEVELOPMENT OF DESIGN METHODS FOR REINFORCED AND UNREINFORCED MASONRY BASEMENT WALLS J.J. ROBERTS Technical Innovation Consultancy Emeritus Professor of Civil Engineering Kingston University, London.

More information

Armanet BEKAERT. Armanet THE CONSTRUCTIVE IDEA. Render & plaster reinforcing mesh @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@

Armanet BEKAERT. Armanet THE CONSTRUCTIVE IDEA. Render & plaster reinforcing mesh @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ BEKAERT Armanet THE CONSTRUCTIVE IDEA Armanet Render & plaster reinforcing mesh Armanet Renovation Product specification Insulation Reinforcing Mesh Armanet is a heavily galvanized welded mesh used for

More information

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...

More information

Always. Reliable. Tight. Wall sleeves Versatile solutions for building entries. cablepipebuildingentry+

Always. Reliable. Tight. Wall sleeves Versatile solutions for building entries. cablepipebuildingentry+ Always. Reliable. Tight. Wall sleeves Versatile solutions for building entries. cablepipebuildingentry+ The wall sleeve The wall sleeve a largely unnoticed but very important sealing part. Wall sleeves

More information

Concrete Design to Eurocode 2

Concrete Design to Eurocode 2 Concrete Design to Eurocode 2 Jenny Burridge MA CEng MICE MIStructE Head of Structural Engineering Introduction to the Eurocodes Eurocode Eurocode 1 Eurocode 2 Materials Cover Flexure Shear Deflection

More information

CITY OF LOS ANGELES CALIFORNIA

CITY OF LOS ANGELES CALIFORNIA BOARD OF BUILDING AND SAFETY COMMISSIONERS HELENA JUBANY PRESIDENT VAN AMBATIELOS VICE-PRESIDENT E. FELICIA BRANNON VICTOR H. CUEVAS GEORGE HOVAGUIMIAN CITY OF LOS ANGELES CALIFORNIA ERIC GARCETTI MAYOR

More information

Structural Failures Cost Lives and Time

Structural Failures Cost Lives and Time Structural Failures Cost Lives and Time Recent failures of storage bins, silos and other structures highlight the need to increase awareness of hazards associated with these structures. Since 2010, one

More information

INDIRECT METHODS SOUNDING OR PENETRATION TESTS. Dr. K. M. Kouzer, Associate Professor in Civil Engineering, GEC Kozhikode

INDIRECT METHODS SOUNDING OR PENETRATION TESTS. Dr. K. M. Kouzer, Associate Professor in Civil Engineering, GEC Kozhikode INDIRECT METHODS SOUNDING OR PENETRATION TESTS STANDARD PENETRATION TEST (SPT) Reference can be made to IS 2131 1981 for details on SPT. It is a field edtest to estimate e the penetration e resistance

More information

INSITU TESTS! Shear Vanes! Shear Vanes! Shear Vane Test! Sensitive Soils! Insitu testing is used for two reasons:!

INSITU TESTS! Shear Vanes! Shear Vanes! Shear Vane Test! Sensitive Soils! Insitu testing is used for two reasons:! In-situ Testing! Insitu Testing! Insitu testing is used for two reasons:! To allow the determination of shear strength or penetration resistance or permeability of soils that would be difficult or impossible

More information

METHOD OF STATEMENT FOR STATIC LOADING TEST

METHOD OF STATEMENT FOR STATIC LOADING TEST Compression Test, METHOD OF STATEMENT FOR STATIC LOADING TEST Tension Test and Lateral Test According to the American Standards ASTM D1143 07, ASTM D3689 07, ASTM D3966 07 and Euro Codes EC7 Table of Contents

More information

Metal Pressfitting Pipe Systems

Metal Pressfitting Pipe Systems VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing

More information

HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES

HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES 101 Retrofits Required. Pursuant to Section 553.844 553.884, Florida Statutes, strengthening of existing site-built,

More information

Advanced bolt assessment through process automation

Advanced bolt assessment through process automation Titelmasterformat Bolt Assessment inside durch ANSYS Klicken bearbeiten Advanced bolt assessment through process automation Contents Short presentation of VDI 2230 Workflow with Bolt Assessment inside

More information

TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE

TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION PART 8000 - PRECAST CONCRETE TABLE OF CONTENTS Item Number Page 8100 PRECAST CONCRETE CONSTRUCTION - GENERAL 8-3 8101 General

More information

PART TWO GEOSYNTHETIC SOIL REINFORCEMENT. Martin Street Improvements, Fredonia, Wisconsin; Keystone Compac Hewnstone

PART TWO GEOSYNTHETIC SOIL REINFORCEMENT. Martin Street Improvements, Fredonia, Wisconsin; Keystone Compac Hewnstone GEOSYNTHETIC SOIL REINFORCEMENT Martin Street Improvements, Fredonia, Wisconsin; Keystone Compac Hewnstone DESIGN MANUAL & KEYWALL OPERATING GUIDE GEOSYNTHETIC SOIL REINFORCEMENT Keystone retaining walls

More information

Chapter 3 DESIGN AND CONSTRUCTION FEATURES IMPORTANT TO SEISMIC PERFORMANCE

Chapter 3 DESIGN AND CONSTRUCTION FEATURES IMPORTANT TO SEISMIC PERFORMANCE Chapter 3 DESIGN AND CONSTRUCTION FEATURES IMPORTANT TO SEISMIC PERFORMANCE To satisfy the performance goals of the NEHRP Recommended Seismic Provisions, a number of characteristics are important to the

More information

Solid shape molding is not desired in injection molding due to following reasons.

Solid shape molding is not desired in injection molding due to following reasons. PLASTICS PART DESIGN and MOULDABILITY Injection molding is popular manufacturing method because of its high-speed production capability. Performance of plastics part is limited by its properties which

More information

Saferand easierinstallation

Saferand easierinstallation EN 85-07 Saferand easierinstallation IföSigninstallationsystem andifösignbuilt-incistern www.ifosanitar.com/sign Aneffectivesolution withmanyadvantages. Ifö Sign installation system makes life a little

More information

Österreichisches Institut für Bautechnik Schenkenstrasse 4 1010 Vienna Austria T +43 1 533 65 50 F +43 1 533 64 23 mail@oib.or.at www.oib.or.

Österreichisches Institut für Bautechnik Schenkenstrasse 4 1010 Vienna Austria T +43 1 533 65 50 F +43 1 533 64 23 mail@oib.or.at www.oib.or. Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating

More information

CF-Mesa, CF-Light Mesa, CF-Flute, CF-Metl-Plank, CF-Striated, CF-Santa Fe, CF-Architectural Flat, CF...

CF-Mesa, CF-Light Mesa, CF-Flute, CF-Metl-Plank, CF-Striated, CF-Santa Fe, CF-Architectural Flat, CF... Building Insulations - Walls and Ceilings (FM Approval Numbers 4411, 4651, 4880, 4881, 4882) Insulating materials may occur in building construction to reduce heat or sound transmission through a wall,

More information

Tubular connection elements

Tubular connection elements KIRÁY TRING KFT H-1151 udapest Mogyoród útja 12 14tel: 061307-3801 Tubular connection elements 429 KIRÁY TRING KFT H-1151 udapest Mogyoród útja 12 14tel: 061307-3801 Technical information on the tubular

More information

Residential Deck Safety, Construction, and Repair

Residential Deck Safety, Construction, and Repair Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the

More information

Lenntech. 1000 psi End port pressure vessels 2.5. User s Guide to: Phoenix Vessel Technology Limited. Model number: 1503

Lenntech. 1000 psi End port pressure vessels 2.5. User s Guide to: Phoenix Vessel Technology Limited. Model number: 1503 1 User s Guide to: Phoenix Vessel Technology Limited 1000 psi End port pressure vessels 2.5. Model number: 1503 Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Phoenix

More information

19 DYNAmax Free Standing Server C A B I N E T s

19 DYNAmax Free Standing Server C A B I N E T s 9 DYNAmax Free Standing Server C A B I N E T s 9 DYNAmax Free Standing Server Cabinets FAMILY W=600mm and W=800mm DYNAmax Series Free Standing Server Cabinets DYNAmax series Servering Enclosures, provide

More information

DESS. Screws. Tijuana Ventas: (664) 685 6294/95 hirambogarin@dabocorp.com. For all major implant systems!! www.dabocorp.com

DESS. Screws. Tijuana Ventas: (664) 685 6294/95 hirambogarin@dabocorp.com. For all major implant systems!! www.dabocorp.com Screws Screws for definitive use. Made from medical grade 5 ELI Titanium Integrity and soundness guaranteed by stress tests of up to 150% of their nominal torques. Their designs ensure a perfect fit with

More information

The Work at Height Safety Association. Guidance on inspecting eyebolts used for personal fall protection purposes

The Work at Height Safety Association. Guidance on inspecting eyebolts used for personal fall protection purposes The Work at Height Safety Association Technical Guidance Note 6 Guidance on inspecting eyebolts used for personal fall protection purposes A series of informative notes for all industries involved with

More information

DYWIDAG-SYSTEMS INTERNATIONAL. DYWIDAG Barrier Cable System. Glendale Galleria Parking Structure, Glendale, California

DYWIDAG-SYSTEMS INTERNATIONAL. DYWIDAG Barrier Cable System. Glendale Galleria Parking Structure, Glendale, California DYWIDA Barrier Cable System lendale alleria Parking Structure, lendale, California COMPONENTS AND STRAND PROPERTIES Barrier Cable System Components Monostrand Anchorage and Pocket Former Barrel & Wedge

More information

Stability. Security. Integrity.

Stability. Security. Integrity. Stability. Security. Integrity. PN #MBHPT Foundation Supportworks provides quality helical pile systems for both new construction and retrofit applications. 288 Helical Pile System About Foundation Supportworks

More information

Chapter. Restoration of Damaged Structures

Chapter. Restoration of Damaged Structures 5 Chapter Restoration of Damaged Structures Bringing back a damaged structure to its pre-earthquake state and original strength is called restoration. This is the first step of building rehabilitation.

More information

B.TECH. (AEROSPACE ENGINEERING) PROGRAMME (BTAE) Term-End Examination December, 2011 BAS-010 : MACHINE DESIGN

B.TECH. (AEROSPACE ENGINEERING) PROGRAMME (BTAE) Term-End Examination December, 2011 BAS-010 : MACHINE DESIGN No. of Printed Pages : 7 BAS-01.0 B.TECH. (AEROSPACE ENGINEERING) PROGRAMME (BTAE) CV CA CV C:) O Term-End Examination December, 2011 BAS-010 : MACHINE DESIGN Time : 3 hours Maximum Marks : 70 Note : (1)

More information

RPS - sales@rpssolar.com - 858 755 4505-12478 San Bruno Cove, San Diego, CA 92130

RPS - sales@rpssolar.com - 858 755 4505-12478 San Bruno Cove, San Diego, CA 92130 RPS - sales@rpssolar.com - 858 755 4505-2478 San Bruno Cove, San Diego, CA 9230 SWH Solar Mount Rail R-MR-SW-SR-0.5, R-MR-SW-SR-2, R-MR-SW-SR-4, R-MR-SW-SR-4B, R-MR-SW-SR-7 Part No. MR-SW-SR-0.5, MR-SW-SR-2,

More information

Chapter 6 ROOF-CEILING SYSTEMS

Chapter 6 ROOF-CEILING SYSTEMS Chapter 6 ROOF-CEILING SYSTEMS Woodframe roof-ceiling systems are the focus of this chapter. Cold-formed steel framing for a roof-ceiling system also is permitted by the IRC but will not be discussed;

More information

Rehabilitation of Existing Foundation Building to Resist Lateral and Vertical Loads

Rehabilitation of Existing Foundation Building to Resist Lateral and Vertical Loads International Journal of Current Microbiology and Applied Sciences ISSN: 2319-7706 Volume 3 Number 12 (2014) pp. 950-961 http://www.ijcmas.com Original Research Article Rehabilitation of Existing Foundation

More information

Uncovered Decks & Porches

Uncovered Decks & Porches Uncovered Decks & Porches Building Guides for Homeowners Why Do I need a Permit? D I D Y O U K N O W? As owner-builder you are the responsible party of record on such a permit. If your work is being performed

More information

Product Catalogue HW-B150H

Product Catalogue HW-B150H Product Catalogue Content 1 Coverage and Terminology... 4 1.1 Design Standards... 4 1.2 Load Criteria... 5 1.3 Definition of Terms... 6 1.3.1 Flood Barrier... 6 1.3.2 Flood Height, effective Flood Height,

More information

60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING

60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING 60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed

More information

VdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)

VdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01) VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,

More information

WHI 90-Minute Rated Veneered Door Frame Installation Instructions

WHI 90-Minute Rated Veneered Door Frame Installation Instructions No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,

More information

INSTRUCTIONS: LocknCharge Laptop Carts

INSTRUCTIONS: LocknCharge Laptop Carts INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes

More information

CITY OF LOS ANGELES CALIFORNIA

CITY OF LOS ANGELES CALIFORNIA BOARD OF BUILDING AND SAFETY COMMISSIONERS VAN AMBATIELOS PRESIDENT E. FELICIA BRANNON VICE PRESIDENT JOSELYN GEAGA-ROSENTHAL GEORGE HOVAGUIMIAN JAVIER NUNEZ CITY OF LOS ANGELES CALIFORNIA ERIC GARCETTI

More information

6 RETROFITTING POST & PIER HOUSES

6 RETROFITTING POST & PIER HOUSES Retrofitting Post & Pier Houses 71 6 RETROFITTING POST & PIER HOUSES by James E. Russell, P.E. 72 Retrofitting Post & Pier Houses Retrofitting Post & Pier Houses 73 RETROFITTING POST AND PIER HOUSES This

More information

MILMAN & ASSOCIATES STRUCTURAL CONSULTING ENGINEERS/ PROJECT MANAGERS

MILMAN & ASSOCIATES STRUCTURAL CONSULTING ENGINEERS/ PROJECT MANAGERS MILMAN & ASSOCIATES STRUCTURAL CONSULTING ENGINEERS/ PROJECT MANAGERS May 29, 2013 Revision B Structural Guideline for Design and Installation Holes in Composite Floor Slab Terminal 3, Departure Level

More information

SUBMITTAL 10 FEET. Cast Iron Soil Pipe Products Hubless Pipe & Fittings HUBLESS PIPE 10 FEET*

SUBMITTAL 10 FEET. Cast Iron Soil Pipe Products Hubless Pipe & Fittings HUBLESS PIPE 10 FEET* QUALITY SYSTEM SUBMITTAL Hubless Pipe & Fittings R E G I S T R AT I O N Manufacturer s T J B 10 FEET HUBLESS PIPE 10 FEET* NOM. SIZE B INSIDE DIAMETER J OUTSIDE DIAMETER 1 1/2 1.50 1.90 0.16 0.13 28.4

More information

Precision Miniature Load Cell. Models 8431, 8432 with Overload Protection

Precision Miniature Load Cell. Models 8431, 8432 with Overload Protection w Technical Product Information Precision Miniature Load Cell with Overload Protection 1. Introduction The load cells in the model 8431 and 8432 series are primarily designed for the measurement of force

More information

Wrap-N-Drain X CCMC 13094-R. EVALUATION DIVISION 07111 REPORT Issued 2002-11-15 Revised 2003-01-08 Re-evaluation due 2005-11-15

Wrap-N-Drain X CCMC 13094-R. EVALUATION DIVISION 07111 REPORT Issued 2002-11-15 Revised 2003-01-08 Re-evaluation due 2005-11-15 National Research Council Canada Institute for Research in Construction Conseil national de recherches Canada Institut de recherche en construction CCMC 13094-R &&0& EVALUATION DIVISION 07111 REPORT Issued

More information

HALFEN UNIVERSAL CONNECTION HUC 12-E CONCRETE. NEW! HALFEN HSCC type tested steel corbels

HALFEN UNIVERSAL CONNECTION HUC 12-E CONCRETE. NEW! HALFEN HSCC type tested steel corbels HALFEN UNIVERSAL CONNECTION HUC 12-E CONCRETE NEW! HALFEN HSCC type tested steel corbels H A L F E N H U C U N I V E R S A L CO N N E C T I O N System Description HSC-B Concrete steel connection Cast in

More information

Field Damage Inspection and Static Load Test Analysis of Jiamusi Highway Prestressed Concrete Bridge in China

Field Damage Inspection and Static Load Test Analysis of Jiamusi Highway Prestressed Concrete Bridge in China Advanced Materials Research Vols. 163-167 (2011) pp 1147-1156 Online available since 2010/Dec/06 at www.scientific.net (2011) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amr.163-167.1147

More information

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing Substrate, structural panel, bonded waterproofing The universal substrate for tiles Perfect covering No matter whether you work with mosaics or large format tiles, an absolutely level substrate with straight

More information

Foundation Experts, LLC Specializes in Foundation Repair and Waterproofing

Foundation Experts, LLC Specializes in Foundation Repair and Waterproofing 1 Most basements show some signs of leaking and cracking. Through the years, problems with water, poor soils, grading, drainage and possible settling affect the integrity of a basement. Being able to recognize

More information

Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille

Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille Text example Compile and tender according to requirements. Please refer to technical data below for respective

More information

RISABase. Rapid Interactive Structural Analysis Base Plate and Anchorage Analysis & Design. Version 2.1 - General Reference

RISABase. Rapid Interactive Structural Analysis Base Plate and Anchorage Analysis & Design. Version 2.1 - General Reference RISABase Rapid Interactive Structural Analysis Base Plate and Anchorage Analysis & Design Version 2.1 - General Reference 26632 Towne Centre Drive, Suite 210 Foothill Ranch, California 92610 (949) 951-5815

More information

Chapter 3 FOUNDATIONS AND FOUNDATION WALLS

Chapter 3 FOUNDATIONS AND FOUNDATION WALLS Chapter 3 FOUNDATIONS AND FOUNDATION WALLS This chapter discusses foundations and foundation walls constructed using the two most common foundation materials concrete and masonry. Although the IRC permits

More information

NEW CONNECTION INDUSTRIAL PRODUCTS NC.10V NC.20V NC.30V. NC. SD.10 NC. SD.20 NC. F.Clamp

NEW CONNECTION INDUSTRIAL PRODUCTS NC.10V NC.20V NC.30V. NC. SD.10 NC. SD.20 NC. F.Clamp Repair and Construction. Complete stainless steel pipe repair clamps to repair cracks, fractures, pin holes, torn sockets or welded tees, broken asbest-cement pipe coupling and more. Available for all

More information

SEISMIC VELOCITY TRANSDUCER T1-40

SEISMIC VELOCITY TRANSDUCER T1-40 SEISMIC VELOCITY TRANSDUCER T1-40 Measurement of Omnidirectional Absolute Vibrations Certified according to ATEX 94/9/CE directive OPERATION Transducer T1-40 serves for seismic measurement of the absolute

More information

Guidelines for the Design of Post-Tensioned Floors

Guidelines for the Design of Post-Tensioned Floors Guidelines for the Design of Post-Tensioned Floors BY BIJAN O. AALAMI AND JENNIFER D. JURGENS his article presents a set of guidelines intended to T assist designers in routine post-tensioning design,

More information

USP SIP Connection Manual www.uspconnectors.com

USP SIP Connection Manual www.uspconnectors.com SIP Connection Manual www.connectors.com Structural Insulated Panels (SIP) supplies quality products to build Stronger Safer Structures Los Angeles San Francisco Minneapolis Houston Tampa Charlotte Philadelphia

More information

SCS Directory Accreditation number: SCS 0115

SCS Directory Accreditation number: SCS 0115 International standard: ISO/IEC 17025:2005 Swiss standard: SN EN ISO/IEC 17025:2005 METRON SA Calibration Laboratory Via Luserte Sud 7 CH-6572 Quartino Head: Angelo Capone Responsible for MS: Angelo Capone

More information

European Technical Approval ETA 13/0384

European Technical Approval ETA 13/0384 European Technical Approval ETA 13/0384 Trade Name Holder of the approval Website Generic type and use of construction product Isobriq EU, Isobriq LE, Isobriq PA & Isobriq ZE Isobriq sa 49 Rue Slar 4801

More information

REHABILITATION OF THE FIGUEIRA DA FOZ BRIDGE

REHABILITATION OF THE FIGUEIRA DA FOZ BRIDGE REHABILITATION OF THE FIGUEIRA DA FOZ BRIDGE A.Rito Proponte, Lda, Lisbon, Portugal J. Appleton A2P Consult, Lda, Lisbon, Portugal ABSTRACT: The Figueira da Foz Bridge includes a 405 m long cable stayed

More information

Excerpts from the Canadian National Building Code (NBC)

Excerpts from the Canadian National Building Code (NBC) Excerpts from the Canadian National Building Code (NBC) Reproduced here with Permission of the Copyright Owner, the National Research Council of Canada, Institute for Research in Construction. For more

More information

EAST LYME HIGH SCHOOL

EAST LYME HIGH SCHOOL Overview: 1971 N 1966 GYM 1966 CLASSROOM WING 1966 AUD. 1971 GYM 1998 1998 POOL EAST LYME HIGH SCHOOL Original 1966 Building: The original East Lyme High School was constructed in 1966 and was composed

More information

IPR-02-64. Äspö Hard Rock Laboratory. International Progress Report. Temperature Buffer Test. Report for retaining plug and anchoring

IPR-02-64. Äspö Hard Rock Laboratory. International Progress Report. Temperature Buffer Test. Report for retaining plug and anchoring International Progress Report IPR-02-64 Äspö Hard Rock Laboratory Temperature Buffer Test Report for retaining plug and anchoring Richard Bäck Äspö HRL September 2002 Svensk Kärnbränslehantering AB Swedish

More information

EXTeRUS. EXTeRUS - With patented design, able to join technology. and quality of materials with a charming shape. Unique

EXTeRUS. EXTeRUS - With patented design, able to join technology. and quality of materials with a charming shape. Unique EXTeR US G L A S S - With patented design, able to join technology and quality of materials with a charming shape. Unique thanks to its outstanding loading capability with 150 kg maximum weight and height

More information

The WANZ Guide to Window Installation

The WANZ Guide to Window Installation The WANZ Guide to Window Installation as described in E2/AS1 Amendment 5 Ver. 1.1 Page 2 of 74 Contents Overview Page 5 Objective Page 5 Scope Page 5 Opening Preparation Page 7 Step P1 Preliminary Check

More information

Slides and Drawers. The right collection

Slides and Drawers. The right collection Slides and Drawers The right collection 1Technical Details Drawer Runners Carrying capacity Kg. Static load Dynamic load Pag. 01 Concealed Runners Excel N Excel N Excel N Excel N650 Excel N Excel PlugIn,

More information

CRITERIA FOR PRELOADED BOLTS

CRITERIA FOR PRELOADED BOLTS National Aeronautics and Space Administration Lyndon B. Johnson Space Center Houston, Texas 77058 REVISION A JULY 6, 1998 REPLACES BASELINE SPACE SHUTTLE CRITERIA FOR PRELOADED BOLTS CONTENTS 1.0 INTRODUCTION..............................................

More information

Composite Construction with KÖCO- Stud Welding Technology IMPRESSIVE TECHNOLOGY 6/2005 1.1

Composite Construction with KÖCO- Stud Welding Technology IMPRESSIVE TECHNOLOGY 6/2005 1.1 Composite Construction with KÖCO- Stud Welding Technology IMPRESSIVE TECHNOLOGY 6/2005 1.1 Composite Construction with KÖCO Stud Welding Technology What is composite construction? An outstanding feature

More information