SPECIFICATION 宏致電子股份有限公司 桃園縣中壢市東園路 13 號. No.13, Dongyuan Rd., Jhongli City, Taoyuan County 320, Taiwan (R.O.C.)

Transcription

1 SPECIFICATION 宏致電子股份有限公司 桃園縣中壢市東園路 13 號 No.13, Dongyuan Rd., Jhongli City, Taoyuan County 320, Taiwan (R.O.C.) TEL: FAX: SPEC. NO.: PS XXXXX-XXX REVISION: B PRODUCT NAME: MICROWAVE COAXIAL CONNECTORS WITCH SWITCH SWD TYPE PRODUCT NO: PREPARED: CHECKED: APPROVED: MARK TUAN ERIC KUO JASON CHEN DATE: 2014/11/07 DATE: 2014/11/07 DATE: 2014/11/07

2 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 2 OF 9 1 REVISION HISTORY SCOPE APPLICABLE DOCUMENTS REQUIREMENTS PERFORMANCE INFRARED REFLOW CONDITION PRODUCT QUALIFICATION AND TEST SEQUENCE...9 Page 2

3 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 3 OF 9 1 Revision History Rev. ECN # Revision Description Approved Date 1 ECN NEW MARK O ECN RELEASE MARK A ECN ADD Working voltage JASON 2014/01/09 B ECN ADD Contact Retention Force MARK 2014/11/07 Page 3

4 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 4 OF 9 2 SCOPE This specification covers performance, tests and quality requirements for the Microwave coaxial Connectors Witch Switch SWD Type 3 APPLICABLE DOCUMENTS EIA-364 : ELECTRONICS INDUSTRIES ASSOCIATION 4 REQUIREMENTS 4.1 Design and Construction Product shall be of design, construction and physical dimensions specified on applicable product drawing. 4.2 Materials and Finish Housing: Thermoplastic, High temp. UL94V-0, Halogen Free Color: Black Contact: High performance copper alloy Plated: (a) Finish: See order information (b) Under plate: Nickel-plated allover Shell : High performance copper alloy Plated: 4.3 Ratings (a) Finish: See order information (b) Under plate: Nickel-plated allover Working voltage less than 36 volts AC(per pin) Rated Voltage: AC 250 Vrms Nominal characteristic impedance: 50Ω Frequency: DC~6GHz VSWR: 1.2 MAX. at 0.1~3.0 GHz 1.3 MAX. at 3.0~6 GHz (Not mated) VSWR: 1.4 MAX. at 0.1~3.0 GHz 1.8 MAX. at 3.0~6 GHz (Mated) Service temperature: -40 ~ +85 C Page 4

5 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 5 OF 9 5 Performance 5.1. Test Requirements and Procedures Summary Item Requirement Standard Product shall meet requirements of Visual, dimensional and functional Examination of Product applicable product drawing and per applicable quality inspection specification. plan. Contact Resistance ELECTRICAL Open circuit voltage : 20mV Max. Circuit current : 100mA Max.(DC or AC1KHz) (EIA ) Insulation Resistance Initial 500 M Ω Min. after testing 100 M Ω Min. Unmated connectors, apply 100 V DC between adjacent terminals. (EIA ) Dielectric Withstanding Voltage AC 300 VAC Min. at sea level for 1 minute. No discharge, flashover or breakdown. Test between adjacent contacts of unmated connectors. (EIA ) Frequency : 0.1~6GHz Not mated 1.2 Max. at 0.1~3.0GHz 1.3 Max. at 3.0~6.0GHz VSWR Mated 1.4 Max. at 0.1~3.0GHz 1.8 Max. at 3.0~6.0GHz Page 5

6 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 6 OF 9 MECHANICAL Item Requirement Standard Durability (mating/unmating, with corresponding plug Plug 100 cycles (EIA ) Vibration Electrical discontinuity : No electrical discontinuity grater than 1µs or more Frequency : 10Hz 55Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 axis. (EIA , test conditions VII, test condition letter D) Shock Contact Retention Force Electrical discontinuity : No electrical discontinuity grater than 1µs or more 0.25 Kgf Min. Acceleration of 490 m/s 2 (50G), 6 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. (EIA , test condition H) Operation Speed : 25.4 ± 3 mm/min. Measure the contact retention force with Tensile strength tester. Page 6

7 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 7 OF 9 ENVIRONMENTAL Item Requirement Standard Thermal Shock Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Insulation resistance : initial 500 mega-ohm Min. after testing 100 mega-ohm Min. Apply the following environment to the mating connector. Temperature, duration. -55 (30min.) +5~35 (5min.) +85 (30min.) +5~35 (5min.) No. of cycles : 5 cycles (EIA ) Humidity Appearance : Looseness between the parts, chipping, breakage or Apply the following environment to other abnormality shall not occur. the mating connector. Temperature : 40±2 Humidity : 90~95%RH Insulation resistance : initial 500 Duration : 96 hours mega-ohm Min. after testing 100 (EIA , Test condition A) mega-ohm Min. Salt spray High temperature life Appearance no abnormality adversely affecting the performance shall occur. Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Apply the following environment to the mating connector. Temperature : 35±2 Salt water density by weight : 5±1% Duration : 8 hours Apply the following environment to the mating connector. Temperature : 85±2 Duration : 96 hours (EIA , Test condition III Method A ) Solder ability Solder able area shall have minimum of 95% solder coverage. Subject the test area of contacts into the flux for 5-10 sec. And then into solder bath, Temperature at 245 ±5, for 4-5 sec. (EIA ) Page 7

8 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 8 OF 9 6 INFRARED REFLOW CONDITION 6.1. Lead-free Process Page 8

9 RELEASE DATE: 2014/11/07 REVISION: B ECN No: ECN PAGE: 9 OF 9 7 PRODUCT QUALIFICATION AND TEST SEQUENCE Test Group Test or Examination Test Sequence Examination of Product Contact Resistance Insulation Resistance 3 8 Dielectric Withstanding Voltage 4 9 VSWR 1 Durability 3 Vibration 3 Shock 4 Contact Retention Force 1 Thermal Shock 5 Humidity 6 Salt spray 3 High temperature life 3 Solder ability 1 Resistance to Soldering Heat 2 Sample Size Page 9