Messerschmitt Me-410 Hornisse
|
|
- Cornelia Walton
- 7 years ago
- Views:
Transcription
1 Messerschmitt Me-410 Hornisse Manual Version 1.0 July 2009 Scale: 1/12 Wingspan: 51.6 in Area: 387 sq in Weight: Power: 2x C3536 Brushless Outrunner Motors Original Design By and Copyright of Timo Starkloff
2 Introduction The Me 410 features simple, robust construction and fast, nimble flight that make it an ideal combat model. It isn t a beginner s model though. For strength, white glue or aliphatic resin should be used throughout. Construction Fuselage: Each main fuselage side is made of four parts: FS1, FS2, FS3 and FS4. Glue the four parts together, noting the grain orientation of FS4. Builder-supplied parts: 2 each 3/8 x 3/4 x 24 Balsa sticks 6 each 3/16 square x 24 Balsa sticks 6 each 1/16 x 4 x 24 Balsa sheets 4 each 3/16 x 3 x 24 Balsa sheets 1 each 3/16 x 4 Hardwood dowel 1/4" Nylon bolt Flexible pushrods as desired Finishing materials Glue the wing saddle doublers F3, tail doublers F14 and the 3/16 square stringers to the fuselage sides. Be sure to make a left and a right side. Taper the tail doublers F14 until they will fit according to the plan top view. Version 1.0 Page 2
3 Glue a 3/16 stringer across the front of former F9, aligning it with the bottom edge of the former. Glue formers F8, F9 and F10 between the two fuselage sides. Glue the servo tray F14 in place. Glue doubler F8A in place. Moisten the fuselage sides at FS4 and glue former F7 in place. Glue formers F11, F12 and F13 in place, and glue formers F14 together. Make a wing mounting plate from 1/8 ply, about 2-3/4 x 1-1/2 inches. Trim to fit and glue it in place in the notches in wing saddle doublers F3. Install flexible cables or pushrods for the rudder and elevators as desired. For best control install a separate pushrod for each elevator. Plank the fuselage top and bottom with cross-grain 3/16 balsa. Glue former F6 to the nose of the fuselage. Add two pieces of scrap 1/4 balsa to round out the nose as shown on the plan. Carve and sand the fuselage to the shape shown on the cross section views. Version 1.0 Page 3
4 Make four nacelle skins from 3/16 balsa, 10 inches by 1-1/2 inches. Again, make them cross grain so that they will bend to fit the bottom curve of the nacelle. Glue a 1-3/4 inch wide nacelle skin to the bottom of the nacelle, centered on the keel N3 and running to the forward edge of N4. When that nacelle skin has dried, use a sanding block to sand 45-degree edges into the bottom skin and the nacelle sides N1 and N2. Refer to the cross section view on the plan. Nacelles: Glue formers N4, N5 and N6 to keel N3. Glue a 1-1/2 inch wide nacelle skin across N1 and the bottom skin. Glue another across N2 and the bottom skin. Carve and sand per the cross section shown on the plan. Glue nacelle sides N1 and N2 to the formers N4, N5 and N6. Note that N1 must be on the inner side of the nacelle, nearest the fuselage. Be sure to make a right nacelle and a left nacelle! Glue a 3/16 square balsa strip into the corners where N1 and N2 meet N4. Also glue a 3/16 square strip to the insides of N1 and N2, aligning the strip with the top edge of the nacelle sides. Make two nacelle skins from 3/16 balsa. The skins should be 10 inches by 1-3/4 inches, with cross grain so that the skins will bend along N3. Version 1.0 Page 4
5 Motor Mounts: Each motor mount consists of six 1/16 plywood parts. Glue the two sides and a top and bottom together. Glue the motor mount to the sides, top and bottom. Glue the motor mount doubler to the inside of the motor mount. Glue the motor mount assembly to N4. Version 1.0 Page 5
6 Wing: Edge-glue the three piece bottom wing skin together. Make up a top wing skin to match, but make it about 1/8 inch wider chord. Glue the aileron servo mount in place. Pin the bottom wing skin to a flat building board. Pin just in front of the spar position. Don t pin the fore or aft portions in place. Glue the main spar W13 and spar doubler W14 together. Put false leading edge W12 in place on top of the bottom wing skin(but do not glue) and hold it there by pinning the leading edge stick against it. Fit ribs W2 through W9 to the spar. Then set the assembled ribs and spar in place on the bottom wing skin. Push the ribs forward into contact with the false leading edge, and align the ribs with the etched marks on the bottom skin. Now glue the spar to the bottom wing skin, and glue the ribs to the spar. Install the wing jig under the rear of the bottom wing skin as shown on the plan. Pin the bottom wing skin and the wing jig in place. Unpin the leading edge stick and remove the false leading edge. Use scrap balsa under the skin to raise the wing bottom skin into contact with the ribs forward of the spar. Glue the ribs to the wing bottom skin. Glue the false leading edge in place. Glue ribs W1 and W10 in place. Glue the aileron leading edge in place. Glue false ribs in place at each end of the aileron. Remove any pins that would be inside the finished wing. Gently press the aft ends of the ribs against the bottom wing skin and glue the ribs to the bottom wing skin from the spar to the trailing edge. Version 1.0 Page 6
7 Construction Manual: Messerschmitt Me 410 Hornisse K Glue the top wing skin to the assembled ribs, spar and bottom skin. Pin and apply weights to hold it firmly in place until the glue sets. K Glue the 3/8 x 3/4 balsa leading edge in place. Carve and sand to the correct contour. Make sure the nacelles fit correctly. K Glue the wing tips in place. Carve and sand to the correct contour. K Cut out the aileron. Trim 1/8 inch from the leading edge of the aileron. Cut an aileron leading edge from scrap 1/8 balsa and glue it in place. K Hinge the aileron to the wing panel. K Build the other wing panel. K Glue the wing panels together. Reinforce the joint with fiberglass tape and epoxy. K Fit the 3/16 dowel in the leading edge of the wing. Install the wing in the fuselage. Mark the location of the wing mounting bolt and drill a hole for it through the wing and the wing mounting plate. K Glue the nacelles in place. Version 1.0 Page 7
8 Bring the motor wiring through the wing and nacelles. Trim and fit the plastic nacelle covers. Trim and fit the plastic cowlings. Use small wood screws such as servo mounting screws to hold the nacelle covers and cowlings in place. Inlay small hardwood block at the screw locations for more secure mounting. Canopy: Make a cockpit floor from 1/8 sheet balsa. Add a piece of 3/16 balsa at the rear for the canopy frame. You can make the canopy removable for access to the interior of the fuselage. Glue lengths of 1/8 square balsa along the sides of the cockpit floor. Glue a 3/4 wide strip of 1/8 balsa across the nose of the cockpit floor. Sand the cockpit floor to shape. Paint the cockpit floor black or dark grey. Version 1.0 Page 8
9 Empennage: Cut and fit all hinge slots before installing the fin and horizontal stabilizer. Mark and cut the fuselage top planking to permit installation of the fin. Slide the horizontal stabilizer in place in the fuselage slot. When satisfied with its alignment, glue it in place. Glue the fin in place. Trim and fit the plastic canopy. Glue the plastic canopy to the cockpit floor. Hinge the rudder and elevators and glue in place. Version 1.0 Page 9
10 Gun Barbettes: Assemble the gun barbettes from parts B1, B2 and B3. Sand to correct shape. Make gun breeches from scrap balsa wood. Paint and glue in place. Install lengths of 1/16 aluminum tube to simulate gun barrels. Use a short length of toothpick or 1/16 dowel to mount the barbette onto the fuselage in the hole provided. This is a photo of a full-scale gun barbette on an actual Me 410: Finish: We suggest that you cover the entire model with lightweight iron-on plastic covering. Fiberglass cloth and thinned finishing resin can be used to reinforce the bottom of the fuselage and the nacelles, but be careful not to let the weight build up. Control Surface Deflections: Use the suggested control surface deflections for the first flight! Aileron +/- 3/8 inch Elevator +/- 3/8 inch Rudder +/- 1-1/4 inch Version 1.0 Page 10
Junkers Ju 88 Manual Version 1.2 13 March 2008
Junkers Ju 88 Manual Version 1.2 13 March 2008 Specifications Wingspan: 49.75 inches Area: 339 square inches Length: 36.12 inches Power: 2x BP21 Brushless 2x Speed-400 Copyright 2007 Thomas A. Jacoby and
More informationCOMPLETE KIT PARTS LIST
Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction. Wood Bag: COMPLETE KIT PARTS LIST 1 LC-504-01 3/32"x4"x24" Laser Cut Balsa Sheet
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More information98 Turbine Vulcan Build photos
98 Turbine Vulcan Build photos Just some of the useful tools needed plus a quality razor plane FUSELAGE Note: Fitting parts back to front is an easy mistake to make with this build, so mark all part with
More informationBuild and Fly the Fokker D- 8
Details are carefully carried out. Note movable controls The high wing gives it unusual stability Build and Fly the Fokker D- 8 Complete Data From Which You Can Build a Successful Model of a Famous German
More informationLightening Holes. Plastics and Fiberglass. Engine Options. Retract Options. CAD Design. CAD Drawn Plans. Flaps. Cockpit Detail.
messerschmitt ME109E The ME109 was the standard by which all other fighters of WWII were judged. It served the Luftwaffe in almost every capacity, from interceptor to night-fighter to ground attack and
More informationMicro. Pitts Special for the RFFS-100 by Chris O Riley
Micro Pitts Special for the RFFS-100 by Chris O Riley F1 F2 F3 F4 1 2 3 4 All wood 1/32 inch sheet unless otherwise stated. F1 F2 F3 F4 Small balsa blocks for LG reinforcement Small balsa blocks for LG
More informationFront landing gear legs. Carve from balsa block
0 Carve these parts from balsa blocks C-1(2) C-2(3) Note: these cross pieces do not have formers attached. They help establish the proper curve of each fuselage side. Front landing gear legs Carve from
More informationTechnical data. Assembly: Introduction. Before starting construction. Equipment needed. Glider or Electro Glider?
Palio pro S2084 Technical data Wing span: Lenght: Weight: Wing area: Wing loading: El. Motor/ no. of cells: Controls: Introduction 2150 mm 1150 mm 1120 g 1860 g 42 dm2 27 g/dm2 44 g/dm2 600 / 7-8 cells
More informationDL50 Discus Launch Glider
DL50 Discus Launch Glider DL50 Specifications Length: 39 in. (99 cm.) Wingspan: 50in. (127 cm.) Wing Area: 275in 2 (1774 cm 2 ) Weight: 8oz. (227 g.) Revision History Date Revision Notes/Comments 6/12/2004
More informationBUILDING INSTRUCTION SAL-DLG MINI-FIREWORKS. MINI-Fireworks building instruction May 2015. www.pcm.at 1
Wingspan [mm]: 950 Aspect ratio: 7,7 Wing area [dm2]: 11,7 Wing loading [g/dm²] : 12-13 Takeoff weight [g]: 155 (Mini-S), 165 (Mini-Q) Airfoil: AG03 mod 3-side-view version with ailerons BUILDING INSTRUCTION
More informationSILVER WINGS 1/32 GLOSTer gladiator Mk1/mk2 build guide
SILVER WINGS 1/32 GLOSTer gladiator Mk1/mk2 build guide Parts Cleanup As with other Silver Wings kits, parts cleanup is fairly simple, and due to the soft resin they use for their kit, a sprue cutter can
More informationSkywalker X8. Assembly manual January 2013
Skywalker X8 Assembly manual January 2013 This Manual Was Created by Ray Grauberger www.raygrauberger.com Technical Data This is the X-8 FPV wing from Skywalker Technology. The BIG FPV wing! The X-8 has
More informationAssembly and Operating Manual Nano warbirds FW 190 Specification: *Length: 18 1/2"(470mm) *Wing Span: 21 7/10"(550mm)
Assembly and Operating Manual Nano warbirds FW 190 Specification: *Length: 18 1/2"(470mm) *Wing Span: 21 7/10"(550mm) *Flying Weight: 6 1/2 oz (185g) Dear customer, Congratulations on your choice of a
More informationFREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Tools and Glue. Required Materials
Do not try to make your ornithopter using "household materials". If you want it to fly, you have to build it right. FREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Wingspan: 16 inches Weight: 1/4 ounce The Ornithopter
More informationHow To Build A Plane From Scratch
BUILDING INSTRUCTIONS FOR THE SOLANGE (SUN ANGEL) The Solange has had a very long period in which to develop. It was originally designed for flying from the Bwlch in South Wales during 1993 as a glider
More informationWE GET PEOPLE FLYING INSTRUCTION MANUAL
TM WE GET PEOPLE FLYING INSTRUCTION MANUAL 90% prebuilt Great sport scale appearance Factory installed retracts Precovered in genuine UltraCote Prepainted fiberglass cowl Specifications Wingspan:... 65.5
More informationIntroduction. Table of Contents. Specifications
Assembly Manual Table of Contents Introduction...2 Table of Contents...2 Warning...3 Additional Required Equipment...3 Additional Tools and Adhesives...3 Contents of Kit/Parts Layout...4 Warranty Information...5
More information60 Sbach 342 Electric Aerobatic Aircraft
60 Sbach 342 Electric Aerobatic Aircraft Specifications: Wing Span: 60 inches Length: 58 inches Power: Hacker A50-14S (or equivalent) Battery: 3800 5-cell LiPo ESC: 60-70 amp Flying Weight: 4.75-5.25 lbs
More informationWine Rack & Glass Storage Bench Chris Gardner
Wine Rack & Glass Storage Bench Chris Gardner Quantity Length Width Material Part 2 48 16 3/4 birch plywood top, bottom 2 14 16 3/4 birch plywood sides 2 14 13 3/4 birch plywood support dividers 2 3 15
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationREALISTIC FUN SCALE MODEL HUGE, 84 WINGSPAN (IMAA Legal) 1/4 SCALE MODEL BUILDS QUICKLY
84" Fun Scale Fly Baby REALISTIC FUN SCALE MODEL HUGE, 84 WINGSPAN (IMAA Legal) 1/4 SCALE MODEL BUILDS QUICKLY READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS
More informationKatana EP. Specifications. 301 sq in / 19.4 sq dm. * Specifications are subject to change without notice.*
INSTRUCTION MANUAL Katana EP Outrunner Motor Requires: -channel radio w/ micro servos, 0A Brushless ESC, 3 cells.v 00mAh Li-Po battery & charger. Wing Span Wing Area Flying Weight Fuselage Length HIGH
More informationAIRCRAFT GENERAL www.theaviatornetwork.com GTM 1.1 2005 1-30-05 CONTENTS
www.theaviatornetwork.com GTM 1.1 CONTENTS INTRODUCTION... 1.2 GENERAL AIRPLANE... 1.2 Fuselage... 1.2 Wing... 1.2 Tail... 1.2 PROPELLER TIP CLEARANCE... 1.2 LANDING GEAR STRUT EXTENSION (NORMAL)... 1.2
More information1/5 PIPER J-3 CUB. Before commencing assembly,please read these instructions thoroughly. Wing Span:84. 0 in / 2130 mm
INSTRUCTION MANUAL Before commencing assembly,please read these instructions thoroughly. 1/5 PIPER J-3 CUB 1/5 PIPER J-3 CUB Wing Span:8. 0 in / 130 mm Wing Area:968 sq in / 6. 5 sq dm Flying Weight:8.
More informationMS:158 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
MS:158 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------70.9in (180cm). Wing area -----------------644.8sq.in (41.6sq dm).
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationSpecifications. *Specifications are subject to change without notice.*
INSTRUCTION MANUAL Extra 300 EP (0) 50W Motor System Requires : -channel radio w/ mini servos, Outrunner Motor KM37810, w/ Propeller Adaptor HW3010, 0A Brushless ESC with 11x8E proepller, cells 1.8V 300mAh
More informationHave fun, nevertheless!
Nanomum The Nanomum is a small pusher gyro for flying indoors or outdoors in very calm weather. It's got a dc head and is easy to build and easy to fly - I hope. Specs: AUW 70 g / 2.5 oz. Rotor diameter:
More informationNote there are many options for how this model can be built, including:
Page 1 Introduction Welcome to the Su-37 park jet! This model was designed for twin Littlescreamers Park Jet (LSPJ) motors and features a working 3- axis thrust vectoring (TV) system, just like the real
More informationSo begin by making up the two fuselage halves known as FS1 & FS2.
72 MOSQUITO BUILD ARTICLE FUSELAGE Before you start thinking about building the fuselage, you will need the assistance of a building jig otherwise a twisted or distorted fuselage will be net result i can
More informationHow To Build A Roc Plane
SebArt professional line AngelS EVO 50E ARF ASSEMBLY MANUAL The new AngelS EVO 50E ARF, was designed by the 10 times F3A Italian Champion Sebastiano Silvestri, it is the replica of his 2 meter size F3A
More informationBUILDING INSTRUCTION ERWIN XL slope ERWIN XL ultralight - ERWIN XL ultralight Elektro. Erwin XL building Instruction October 2012. www.pcm.
Wing span [mm]: 3000 Aspect ratio: 14,67 Wing area [dm2]: 61,33 Wing loading: Erwin XL slope: 45,6-70,1 Erwin XL ultralight: 20,4 Erwin XL ultralight Elektro: 23,6-24,5 Weight [g]: Erwin XL slope: 2800-4300
More informationSebArt professional line
SebArt professional line New Sukhoi 29S 50E ARF ASSEMBLY MANUAL The new Sukhoi 29S 50E ARF was designed by Italy aerobatic pilot, Sebastiano Silvestri and the design is based on of his new Tournament Of
More informationINSTRUCTION MANUAL. 90% Pre-Built Build as Tail dragger or Tricycle Landing Gear System All Hardware Included
90% Pre-Built Build as Tail dragger or Tricycle Landing Gear System All Hardware Included INSTRUCTION MANUAL Specifications for.40 Wingspan: 52-3/4" Length: 48" Wing Area: 593 sq. in. Weight (Approx):
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationFocke-Wulf Fw 190 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Focke-Wulf Fw 90 Specification: Length :9 mm(57") Wing Span :00 mm(70.9") Wing Area :5. sq. dm.0 sq. ft Wing Loading :0. g/sq. dm.7 oz/sq. ft Flying Weight :5. kg(. lbs) Radio :ch& servos Engine :0 -cycle
More informationDave s Sheet Metal Bending Brake
Dave s Sheet Metal Bending Brake I started building a Zenith CH601XL from plans in mid January 2006. After several failed attempts to bend the rudder spar I ended up going to a local sheet metal shop for
More informationP-40B Warhawk 50 ARF Assembly Manual
P-40B Warhawk 50 ARF Assembly Manual NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature,
More informationRudder Repair and refinish
Rudder Repair and refinish Montgomery 23 Dauntless The before photograph A receipt found inside the boat showed a previous owner had enlisted a boat yard to perform maintenance on the rudder by shortening
More information40% EXTRA 330L ARF Manual
40% EXTRA 330L ARF Manual Please read through the entire manual first. It contains important instructions and warnings concerning the finishing of the model. WARRANTY AND PRODUCT DISCLAIMER Radiowave Hobby
More informationThe. FockeWulf FW-190. Phoenix Part 2 (refinishing) Roy Vaillancourt. By:
The Phoenix Part 2 (refinishing) FockeWulf FW-190 By: Roy Vaillancourt Overview: This is part 2 of the continuing story of the resurrection, rebuilding and restoration of my latest Focke Wulf FW-190. In
More informationAssembly Manual For. Dolphine Jet. Wingspan: 88 in Wingarea: 1479.8 sp in Length: 78.8 in Engine: 50CC. www.pilot-rc.com
Assembly Manual For Dolphine Jet Wingspan: 88 in Wingarea: 1479.8 sp in Length: 78.8 in Engine: 50CC www.pilot-rc.com INTRODUCTION Thank you for purchasing our Dolphin Jet. we strive to achieve the real
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationINSTRUCTION MANUAL TOOLS NEEDED FOR ASSEMBLY: OPTIONAL FINISHING MATERIALS: Champaign, Illinois (217) 398-8970 E-mail: partssupport@hobbico.
INSTRUCTION MANUAL Thank you for purchasing the Hobbico Ultra-Tote! You have purchased one of the finest values available in field support equipment. We think you will be impressed with the design and
More informationO P E R A T I N G I N S T R U C T I O N S
O P E R A T I N G I N S T R U C T I O N S CAUTION The Phase 3 Models Fantom is designed for intermediate to advanced pilots. It's not intended for beginners. It is not a trainer! Specifications AND Features:
More informationSundowner 36 ARF Assembly Manual
Sundowner 36 ARF Assembly Manual Notice All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature,
More informationAssembly Manual For. 30cc 88 Skywolf. www.pilot-rc.com. Note: some photos on the manual is not from Skywolf. But the installation way is the same.
Assembly Manual For 30cc 88 Skywolf Wingspan: 88 in www.pilot-rc.com Wingarea: 1479.8 sp in Length: 78.8 in Engine: 50CC Note: some photos on the manual is not from Skywolf. But the installation way is
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationRETRACTABLE LANDING GEAR
HUGHES H-1 RETRACTABLE LANDING GEAR INSTALLATION INSTRUCTIONS Congratulations on your decision to add retractable landing gear to your RC model of the Hughes H-1. Though originally conceived simply for
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationAlenia Experiences on Composite Structures Repairs Benedetto Gambino
Alenia Experiences on Composite Structures Repairs Benedetto Gambino Amsterdam, 10 May 2007 ALENIA OVERVIEW CFRP roadmap - Wing mouv. Parts -Empennage mouv. parts (H/C sandwich and full depth) -Vertical
More informationMini Edge 540 3D. Assembly Manual
Mini Edge 540 3D Assembly Manual 2 Table of Contents Introduction...2 Specifications...2 Contents of Kit/Parts Layout...3 Required Electronics & Accessories...4 Recommended High Performance Motor Setup*...4
More informationAstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
More informationSuper Stunts 60. Specifications. * Specifications are subject to change without notice.*
A L M O S T- R E A D Y- T O - F LY INSTRUCTION MANUAL Super Stunts 60 0.60-0.75 cu. in. displacement 2-stroke Requires : 4- channel radio w / Specifications 5 standard servos Wing Span Wing Area Flying
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationYou have downloaded this plan+instructions+articles as a kind of freeware. To use it, you must accept the following:
Spitfire Created by: Martin Elmberg (C) 1997 and 2013 Scale 1/12th Made for 1/12th scale combat - Aircombat Engine:.15 IC or 200-400W electro 3-4 servos, 3 channel (aileron, elevator, engine) You have
More informationINSTRUCTION MANUAL. Black Angel. www.copterx.com. Features. Kit Helicopter. Copyright 2009 KY MODEL Company Limited.
INSTRUCTION MANUAL Features - Carbon fiber main blade, tail blade, fly paddle, tail fin for extra weight saving and durability. - CNC machined high grade aluminum rotor head and tail gear box to ensure
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationStandard Sleep Pod Side Entry Assembly Instructions
Standard Sleep Pod Side Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod Pod assembly onsite is a relatively simple exercise for two people
More informationP-51 Mustang 60 ARF Assembly Manual
P-51 Mustang 60 ARF Assembly Manual Specifications Wingspan: 65 in (1653mm) Length: 57 in (1448mm) Wing Area: 743 sq in (47.9 sq dm) Weight: 9.25 10.0 lb (4.2 4.5 kg) Wing Loading: 29 31 oz per sq ft Radio:
More information30a. 31a. 30b 12. 31b. 29a 28a 1/48SCALEHEMSDAUPHIN PAGE2/10
9 11 10 43 42 49 50 32 7 51 52 48 58 5 6 8 59 2 3 4 1 24 30a 31a 30 30b 12 31b 31 28 13 29 29a 28a 1/48SCALEHEMSDAUPHIN PAGE2/10 38 82 38f 85 84 86 83 37d 35 38a 37 60 17 21 20 16 15 87 27 34 40c 36b 36a
More informationBrief introduction----------------------------------------------------------------------------03
A-1 skyraider Brief introduction----------------------------------------------------------------------------03 Specification----------------------------------------------------------------------------------03
More informationBUILDINGA 1/10 SCALE FLATBED TRAILER
VOLUME 1, ISSUE 1 BUILDINGA 1/10 SCALE FLATBED TRAILER BUILT, DESIGNED & WRITTEN BY NATHAN MYERS MATERIALS: FEATURES: While the design was kept simple to allow anyone to be able to build their own trailer,
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More informationBuild a Precision. Crosscutting Sled
Build a Precision Crosscutting Sled On-the-money, splinter-free crosscuts are well within your grasp using most well-made tablesaws, but you do have to do a few things to ensure great results cut after
More informationThese instructions will show you how to install an internal door into a non-loadbearing partition wall. The instructions are split into three parts.
No 8 in the series of 'How to' brochures produced by PlaceMakers, New Zealand How to Frame and Hang a Door These instructions will show you how to install an internal door into a non-loadbearing partition
More information50cc Edge 540T ARF. Instruction Manual. Copyright 2009 Extreme Flight RC
50cc Edge 540T ARF Instruction Manual Copyright 2009 Extreme Flight RC 1 Please take a few moments to read this instruction manual before beginning assembly. We have outlined a fast, clear and easy method
More informationSebArt professional line AngelS 30E ARF
SebArt professional line AngelS 30E ARF ASSEMBLY MANUAL The new AngelS 30E ARF, was designed by the 10 times F3A Italian Champion Sebastiano Silvestri, it is the replica of his 2 meter size F3A competition
More informationBill of Materials: Line Follower: A Zippy Robot That Senses Where to Go PART NO. 2170783
Line Follower: A Zippy Robot That Senses Where to Go PART NO. 2170783 This kit has the parts you'll need with the exception of a few craft items sold separately to make a line-following cart. It uses a
More informationSopwith Camel 60 ARF
Sopwith Camel 60 ARF Assembly manual Specifications Wingspan... 61 in (1551mm) Wing Area... 1236 sq in (79.7 sq dm) Length... 41.3 in (1050mm) Weight... 7.25 8.75 lb (3.3kg 4.0kg) Table of Contents Contents
More informationSIDE CURTAIN COVERING KITS for MG TC, TD & TF
Created on 11/18/2005 4:15:00 PM Created by grantm Page 1 of 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 SIDE CURTAIN COVERING KITS
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationSIG MFG. CO., INC. PO Box 520 Montezuma, IA 50171-0520 www.sigmfg.com
KIT NO.: SIGRC76EGARFG - (Green and White) SIGRC76EGARFR - (Red and White) SPECIFICATIONS: Wing Span: 51.5 in. (1308 mm) Wing Area: 725 sq. in. (46.7 dm 2 ) Length: 48.25 in. (1226 mm) Flying Weight: 5-5.5
More informationNow if I wanted to make life easier, I should have picked only a couple on the wish list, namely a 50 span and a pusher configuration.
49 VULCAN So here we are, one year on from the 2013 RCM&E Special and another war bird to whet your appetite. Now as many of you may remember, we always tried to keep the subject matter for the free plan,
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More information1 Door Tall Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Tall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationmajestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base
majestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base These Instructions are for a left and right handed unit. The diagrams show a left
More informationharbor cub Electric Remote Control Airplane Model 92906 assembly & Operating Instructions
harbor cub Electric Remote Control Airplane Model 92906 assembly & Operating Instructions IMPORTANT: If damage is caused due to a crash, your warranty is void. Visit our website at: http://www.harborfreight.com
More informationCETAC Z-Drive Assembly
CETAC Z-Drive Assembly Replacement Guide Manual Part Number 610144 Rev 1, 2012 CETAC Technologies, Printed in USA Overview This guide describes the necessary steps to replace the Z-drive assembly on your
More informationNavico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement
Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations
More informationWren Kitchens Installation Tips... 3. Carefully check your kitchen delivery... 4. Measuring out and marking up... 5. Fitting the base cabinets...
tra 1 Index Wren Kitchens Installation Tips... 3 Carefully check your kitchen delivery... 4 Measuring out and marking up... 5 Fitting the base cabinets... 6 Fitting the corner cabinets... 7 The 972mm or
More informationSkirt 1 / 4. The Skirt. The skirt patterns were downloaded from Mark's site but they need expanding before they can be used.
Skirt 1 / 4 The Patterns The Skirt The skirt patterns were downloaded from Mark's site but they need expanding before they can be used. I used Corel Draw's real world dimensions to expand the patterns
More informationBUILDING THE PIPER J-3 CUB
BUILDING THE PIPER J-3 CUB INTRODUCTION Top Flite is proud to present it's large, scale version of the legendary J-3 PIPER CUB. Few aircraft in the history of aviation have had the overall appeal of this
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationwith three small holes to supply an indexing head, and is prevented from slipping by means of a piece of spring wire. One feather
OR LEATHER a perfect fifty-four or take your archery with a dash of small game hunting, you will find keen enjoyment in this ancient sport. Making the tackle is simple. Size of tackle: The first thing
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationAir Conditioner Duct Construction & Repair
PROPER ROOF AIR CONDITIONER MOUNTING At Newmar, there are two different models of air conditioners available on all towable and motorized units. The different models are the Dometic Brisk and Penguin models,
More informationLYCOMING O-360. Engine Installation
Engine Installation SECTION 4 Carburetor Heat Box Carb. Heat Box, hole at the bottom is the hot air exit when carb heat is not used. SECTION 4 - Page 1 of 13 Push Pull cable P/N 05-14084 Qty = 1 Length=7ft.
More informationBuild Your Own Solar Car Teach build learn renewable Energy! Page 1 of 1
Solar Car Teach build learn renewable Energy! Page 1 of 1 Background Not only is the sun a source of heat and light, it s a source of electricity too! Solar cells, also called photovoltaic cells, are used
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationINSTRUCTION MANUAL. 254 cm 154 cm 3429 sq cm 5.9-7.3 kg
TM INSTRUCTION MANUAL 100" Wingspan 90% pre-built Covered in Cub yellow WorldTex fabric covering Includes Scale detailing instructions Cub yellow fiberglass cowl included IMAA legal All hardware included
More informationAssembly Manual For. Wingspan: 88 in Wingarea: 1479.8 sp in Length: 78.8 in Engine: 50CC
Assembly Manual For 50cc aerobatic plane Wingspan: 88 in Wingarea: 1479.8 sp in Length: 78.8 in Engine: 50CC www.pilot-rc.com INTRODUCTION Thank you for purchasing our new 50cc aerobatic plane. we strive
More information