TEST REPORT. Report nº: LABEL Date: Laboratório de Ensaios Eléctricos Page nº: 1/11

Transcription

1 Laboratório de Ensaios Eléctricos Page nº: 1/11 TESTING/ELABORATION: Hugo Santos JOB: Laboratory Technician VERIFICATION: Sónia Valério JOB: Laboratory Technician TECHNICAL APPROVAL: João Costa JOB: Technical Supervisor STANDARD/SPECIFICATION: This report is based in the following standards/specifications: EN : A1: A11: 2010 / AC:2012 clauses 7, 8, 10, 15, 16, 18, 24, 26, 27, 28, 29 and 32 EN : 2012 TYPE OF APPLIANCES: MANUFACTURER: TRADEMARK: Hair straightener Unknown Electric Co TYPE/MODEL: JDL-118 SERIAL Nº / BATCH Nº: 248/12 TESTS DEMANDED BY: JMR DATE: May 2013 CUSTOMER ADDRESS: Rua Actor António Silva, Lisboa DATE OF RECEPTION OF SAMPLES: BEGIN OF TESTS: END OF TESTS: REMARKS: ISQ Proposal nº 018/2012 Scheme C of type C test (control tests) NOTES: The results of this report are only referred to the products submitted to the tests. This report can only be reproduced in its totally. APPROVED:

2 Laboratório de Ensaios Eléctricos Page nº: 2/11 1 Scope It was supplied to the Laboratory one sample of a hair straightener,trademark Electrico Co and model JDL In order to assess the compliance of this product to the electrical safety standards in the scope of the Low Voltage Directive, it was demanded by the client the performance of the tests referred in the section 3 on this test report. 2 Identification The appliance supplied to laboratory can be seen in the following photos: General View

3 Laboratório de Ensaios Eléctricos Page nº: 3/11 Nameplate Control Knob

4 Laboratório de Ensaios Eléctricos Page nº: 4/11 Acessories 3 Tests done by the Laboratory There were made sections 7, 8, 10, 15, 16, 18, 24, 26, 27, 28, 29 and 32 of the standard. 4 Conclusions and remarks 4.1 Non compliance resume It was detected non-compliances on sections: 7.12.Z101 and 7.12.Z Remarks There are no remark on this test report. Not verified on clause: Test results

5 Laboratório de Ensaios Eléctricos Page nº: 5/11 7. Marking and instructions 7.1 Pass 7.2 Not applicable 7.3 Not applicable 7.4 Not applicable 7.5 Not applicable 7.6 Pass 7.7 Not applicable 7.8 Not applicable 7.9 Not applicable 7.10 Pass 7.11 Not applicable 7.12 Pass 7.12.Z1 Fail See clause 7.12.Z Z101 Fail The instructions must also available in an alternative format, e.g. or a website Not applicable Not applicable Not applicable Not applicable Pass Not applicable Not applicable Not applicable

6 Laboratório de Ensaios Eléctricos Page nº: 6/ Pass 7.14 Pass 7.15 Pass 7.16 Not applicable 8. Protection against access to live parts 8.1 Pass Pass Pass Not applicable Not applicable Not applicable 8.2 Pass 10. Power input and current 10.1 Pass U e = 230 V => P_rated = 25 W => P_measured = W => P = + 9 % 10.2 Not applicable 15 Moisture resistance 15.1 Pass Not applicable Not applicable 15.2 Not applicable

7 Laboratório de Ensaios Eléctricos Page nº: 7/ Pass Test conditions: -Detachable parts are removed; -Duration: 48 h; - HR = 93 ± 3%; - T = 25 ± 5 ºC 16 Leakage current and electric strength 16.1 Pass 16.2 Pass 16.3 Pass Leakage current I between: I (ma) Required I (ma) L/N and control knobs (metallic foil) < Test voltage applied between: Test voltage (V) Breakdown Live parts and control knobs (metallic foil) 3000 No 18 Endurance Not applicable 24. Components Object/part No. Manufacturer/ trademark Type/model Technical data Mark(s) of conformity Plug WS WS A 250V~ VDE Supply cord ZHEJIANG WANGSHI ELECTRICAL APPLIANCE CO., LTD H03VVH2-F 2x0.75mm 2 VDE Switch GORBO SLJ 3(1)A 250Vac 1EA 6A 125Vac T125 CQC, TUV

8 Laboratório de Ensaios Eléctricos Page nº: 8/11 Object/part No. Manufacturer/ trademark Type/model Technical data Mark(s) of conformity Sheat of internal wiring WOER RSFR-H VW-1 125ºC H(Ø2.0) TESTED ON THE APPLIANCE Internal wiring FENG TAI FENG TAI 22AWG ºC 300/300V 250ºC 250/500V TESTED ON THE APPLIANCE VDE PWB WS J86-KG1-02C 94V-0 UL(E157634) Heating element TESTED ON THE APPLIANCE 24.1 Pass Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable 24.2 Pass 24.3 Not applicable 24.4 Not applicable 24.5 Not applicable 24.6 Not applicable 24.7 Not applicable 24.8 Not applicable

9 Laboratório de Ensaios Eléctricos Page nº: 9/11 24.Z1 Not applicable 26. Terminals for external conductors 26.1 Pass 26.2 Not applicable 26.3 Not applicable 26.4 Not applicable 26.5 Not applicable 26.6 Not applicable 26.7 Not applicable 26.8 Not applicable 26.9 Not applicable Not applicable Pass 27. Provision for earthing 27.1 Pass 27.2 Not applicable 27.3 Not applicable 27.4 Not applicable 27.5 Not applicable 27.6 Not applicable 28. Screws and connections 28.1 Pass 28.2 Not applicable 28.3 Not applicable

10 Laboratório de Ensaios Eléctricos Page nº: 10/ Not applicable 29. Clearances, creepage distances and solid insulation 29.1 Pass Overvoltage category: 2500 V Not applicable Pass Pass Pass Minimum specified clearance: 1.5 mm Clearance measured between wiring basic insulation and cable inlet: >15 mm Minimum specified clearance: 3.0 mm Clearance measured at live parts of heating element and the surface: > 5 mm Minimum specified clearance: 1.5 mm Clearance measured at the live parts of swivel connection:> 2.8 mm Not applicable 29.2 Pass Pollution degree: 2 Material group IIIa: 175 CTI < Not applicable Pass Pass Pass Minimum creepage distance specified: 2.5 mm Creepage between wiring basic insulation and cable inlet: > 15 mm Minimum creepage distance specified: 5.0 mm Creepage measured at live parts of heating element and the surface: > 5 mm Minimum creepage distance specified: 2.0 mm Creepage measured at the pwb: 3.4 mm

11 Laboratório de Ensaios Eléctricos Page nº: 11/ Pass Pass Compliance checked by measurement of clause Minimum thickness specified for supplementary insulation: 1 mm Thickness measured on enclosure: 3.1 mm Not applicable Not applicable Not applicable 29.3.Z1 Not applicable 32. Radiation, toxiticy and similar hazards Not verified The laboratory currently don t have the equipment available to perform the test.