Concealed Tab Mount 17.3 (.68) 11 (.44) 86 (3.38) 44 (1.72) 8 (5/16) Hex wrench opening. Receptacle panel. Latch. panel Ø 13 (.50) 44 (1.72) 19 (.

Transcription

1 306 R2 Draw Concealed Tab Mount Suited for thin panels *13 Ø5 (.196).5 (.).3 (.6) N (2000 lbf) Install assembly with M5 (No. 10) screws (not supplied).3 (5/) Hex wrench Ø 5 (.196) 4 PL.3 * Typical on latch and receptacle min. panel panel (3.) min. (.) 19 (.75) 19 (.75) mm (5/) Hex wrench R R Other options available. For complete details on variety, part numbers, installation and specification, go to

2 R2 Draw Concealed Tab Mount (1.12) Ø 5.5 (.21) (.) 30 (1.19) 3 (1.50) Ø 5.5 (.21) 4 PL 29 (1.13) Suited for thick panels * Performance details.3 panel panel (5/) Hex wrench 52 (2.03) * Typical on latch and receptacle 900N (2000 lbf) Install assembly with Ø 5 (.205) rivets or M5 (No. 10) screws (not supplied) (3.) Ø13 (.) 3 (1.50) mm (5/) Hex wrench R R Other options available. For complete details on variety, part numbers, installation and specification, go to

3 30 R2 Draw Concealed Mortise Suited for mortise or side mount installation Ø 6.6 (.26) 4 pl (.437) 900 N (2000 lbf) Install assembly with Ø 6 (1/4)rivets or M6 (1/4) screws (not supplied). A 1.6 (.06) gap should be maintained between latch and receptacle..3 panel (1.73) 2 pl (3.) ACTUAL (5/) SIZE Hex wrench panel.3 (1.27) 24 (.94).3 (1.27) 6 pl +0.1 Ø (.252 ) (.) mm (5/) Hex wrench R R

4 R2 Draw Concealed Front mount 309 Front mount installation 150 (5.).3 Ø 5.2 (.205) 2 Countersink Front Mount 151 (5.94) 1Pocket (4.3) 4 (.) 2 Countersink (5/) Hex wrench (.) 4.5 Deep recess (.1) 12 (.46) (.67) 1 (4.3) Pocket for mounting ACTUAL 46 (1.0) SIZE Mimimum Clearance for cam rotation Rear Mount 2 Countersink 4 (.) 150 (5.) Ø 5.2 (.205) 4000 N (900 lbf) : Wood application: Install assembly with M5 (No. 10) flat head screws (not supplied). Note: strength is dependant on mounting hardware and installation material Metal application: Install assembly with 5 (.196) flathead rivets or M5 (No. 10) screws. Note: Maximum metal panel thickness should be 2.5 (.10) Actuator hole for latch side only load mm (5/) Hex wrench R R

5 310 R5 Draw Concealed Mortise Mount Consistent pull-up Concealed installation,100 N (2500 lbf) 76,920 N (292 lbf) Install assembly with Ø 6 (1/4) rivets or M6 (1/4) screws (not supplied) Notes Operating force To open: 4 N m (35 in lbf) To close: 4 N m (35 in lbf) 10 (.40).3 6 Holes Ø 6.5 (.2) Recessed Pocket +0.1 Ø (.256 ) -0.0 (5/) Hex wrench Ø 12 (.47).5 panel.5.5 Hook to lock over Ø 10.3 (.40) pin 37 (1.47) 55 (2.) Radius 13.2 (.52) 94 (3.69) Ø 9.5 (.3) (.31) Travel panel.5 Side Mount Exterior of cabinet 12 (.47) 94 (3.69) Ø 6.5 (.2) (6 Holes) Frame.3 45 (1.77) 45 (1.77) mm (5/) Hex wrench R R