The runner is available in two versions: - fixed to the drawer by locating pin (see page 20) - fixed to the drawer by clip (see page 22)

Transcription

1

2 2

3 3

4 The Unica full extension concealed runner combines Smove decelerated closing action with both traditional opening and Push self-opening for handle-less furniture. The fully integrated operating system is completely mechanical and therefore does not require a power source. The runner is available in two versions: - fixed to the drawer by locating pin (see page 20) - fixed to the drawer by clip (see page 22) 4

5 Handle-less opening Push the frontal to open the drawer. The drawer opens approximately 5-10 cm. Open the drawer to access the inner space. Open drawer. Closing with decelerating effect. Opening with handle Pull the handle to open the drawer. Open drawer. Closing with decelerating effect. 5

6 - Fixing Fixing full-extension runner on cabinet side ø ø 3.5 ø ø 6.3 (MAX.) EUROSCREW Pre-drilling ø ø The oval slot allows the easy alignment of drawer frontals particularly in multi drawer and Push applications. Drilling positions for runner on cabinet side. Full-extension For the function Push is required an A value = 2,5 mm. This value is obtained by placing the runner at 37 mm from the edge of the cabinet A = 2,5 37 Detail of the rear additional fixing hole ø 6,3 6,75 7,15 6

7 Drawer setting Drawer setting: abbreviations Chest of drawers SP = Thickness of the drawer LN = Nominal runner length PM = Depth of the cabinet X = Internal width of the cabinet SP LN X PM Drawer dimensions LC = Runner length - 10 mm X - 41 = Internal width of the drawer LC X - 41 The drawer length is 10 mm shorter than the runner length The internal width of the drawer is 41 mm less than the internal width of the cabinet 7

8 ø 7x10 ø 7x10 - Pin fix clip - Drawer drilling ø 7x8 Drawer drilling Drawer with frontal - three-sided (view from below) Template for drawer drilling - see page ø 7x8 20 Min. 53 Min. 53 Min. 33 B 5 20 C 11 Min. 33 ø 7x106 B C 45 ø 7x106 A LN - 10 A Drawer drilling Internal drawer - four-sided (view from below) Template for drawer drilling - see page 26 B 5 20 ø 7x8 C ø 7x8 Min B C ø 7x10 SP A 11 ø 7x10 Min. 33 ø 7x10 6 SP 45 + SP 11 ø 7x LN SP 7 A Rear hook drawer locating pin security pin 8

9 Pin-fix clip - technical information Fixing of the drawer security pin Available on all runner versions This operation is tool free The device locks the drawer onto the runners 9

10 - pin-fix clip - adjustments Height adjustment + 3 mm Initial position of the lever for the height adjustment. + - Turn the lever towards the front of the drawer to achieve the height adjustment. This operation is tool free. = = + 3 mm 10

11 Pin-fix clip - adjustments Depth adjustment + 2 mm - 2 mm Rotate the black wheel towards the front of the drawer to increase the gap between the front and the side. This operation is tool free. + 2 mm Rotate the black wheel towards the back of the drawer to reduce the gap between the front and the side. This operation is tool free. - 2 mm 11

12 ø 7x10 Min. 33 ø 7x10 - Clip version - Drawer drilling Drawer drilling Drawer with frontal - three-sided (view from below) 45+SP 26 Min. 58 ø 7x10 ø 8x5 11 Min. 33 Min SP A 11 ø 6x LN - 10 Drawer drilling Internal drawer - four-sided (view from below) SP A 11 7 LN - 10 Real hook 12

13 1 way adjustable clip - Technical information - adjustment Clip fixing Drawer adjustment Drawer height adjustment (+ 2,5 mm) using the lever indicated 13

14 - With 3 way adjustable clip The 3 way adjustment allows to: - align the drawers between them; - align the drawers with the cabinet. Features and benefits of the clip: - for all versions of full-extension runners - tool free 3 way adjustment - patented removal system of the drawer, from both the front and the sides of the drawer - clip manufactured in Carbon Fibre rich material for light weight, strength and rigidity Clip assembly Position the left and the right clip at the front of the drawer. Fix with the screws on the bottom or on the front of the drawer as indicated in the images below

15 3 way adjustable clip - Removal The drawer can be removed operating from both the front and the sides. Removal from the front: position the hands under the front of the drawer and operate on the orange levers, as indicated in the drawing, sliding the drawer forward. Removal from the side: position the hands under both sides of the drawer and operate on the orange levers, as indicated in the drawing, sliding the drawer forward. 15

16 - With 3 way adjustable clip Height adjustment mm Initial position of the lever for the height adjustment + - Push the lever towards the outside of the drawer to achieve the height adjustment. This operation is tool free. = = 16

17 Sideways adjustment mm mm Rotate the white wheel towards the front of the drawer to adjust left. The clip shows the position 0. This operation is tool free. 1.5 mm Rotate the white wheel towards the back of the drawer to adjust right. The clip shows the position 0. This operation is tool free. 1.5 mm For sideways adjustment, it is recommanded that the adjusters on the clips are operated in the same direction, in order to maintain the correct alignement and movement of the runners. 17

18 - With 3 way adjustable clip Depth adjustment + 2 mm - 2 mm Rotate the black wheel towards the inside of the drawer to reduce the gap between the front and the side. The clip shows the position 0. This operation is tool free. - 2 mm Rotate the black wheel towards the ouside of the drawer to increase the gap between the front and the side. The clip shows the position 0. This operation is tool free. + 2 mm 18

19 Technical information Full-extension Drawer length = extension Industrial packing = 20 pairs Clip version Pallet: - length from 300 to 400 mm = 300 pairs - length from 450 to 500 mm = 280 pairs Pin version Pallet: - length from 300 to 400 mm = 300 pairs - length from 450 to 500 mm = 280 pairs 50 x Clip part number Packing = 100 pairs Clip part number Packing = 100 pairs X Part number composition - runners Example: BASIC PART NUMBER ARTICLE (ex. 652) ARTICLE VERSIONS: 80 = Unica PACKING: 0 = industrial FIXING ON CABINET SIDE: 0 = to be screw fixed RUNNER LENGTH (in mm) 19

20 concealed runner Full-extension runner system fixed to the drawer by locating pin. The Push self-opening system for handle-less drawers is fully integrated into the runner. A slight pressure on the drawer frontal is sufficient for the drawer to self-open. The Smove decelerated closing action is also fully integrated into the runner. Product features - Safety system that secures the drawer to the runner. - Drawer height adjustment +3 mm and depth adjustment ±2 mm. - The drawer is maintained parallel with the cabinet side during opening. - Drawer fixing without screws. - Finish: bright zinc-plated. Dimensions X Min. 5 Max. 16 ø7 ø7 9, ,5 42, X

21 Part number BASIC PART NUMBER RUNNER LENGTH (LN) = MIN. DEPTH OF THE CABINET (PM) To be screw fixed Screw TSP ø 3,5 mm Fixing the drawer onto the runners The flexibility of the system enables the locating pin to be engaged simply by placing the drawer onto the runners and closing it. Detail of the pin-fix clip premounted on the runner, with: - Tool free height and depth adjustment; - Safety device to prevent the drawers from turning over; - Locating pin. Detail of the integrated systems into the runner: - Push, which allows the opening of handle-less drawers. - Smove, which allows the decelerated closing of the drawers. 21

22 concealed runner Full-extension runner system fixed to the drawer by clip. The Push self-opening system for handle-less drawers is fully integrated into the runner. A slight pressure on the drawer frontal is sufficient for the drawer to self-open. The Smove decelerated closing action is also fully integrated into the runner. Product features - Safety system that secures the drawer to the runner. - Drawer height adjustment +2.5 mm with clip Drawer height adjustment +2.5 mm, side adjustment ±1.5 mm, depth adjustment ±2 mm with clip The drawer is maintained parallel with the cabinet side during opening. - Finish: bright zinc-plated. Dimensions X MIN. 5 MAX. 16 9, , , x

23 Part number BASIC PART NUMBER RUNNER LENGTH (LN) = MIN. DEPTH OF THE CABINET (PM) To be screw fixed Screw TSP ø 3,5 mm Fixing the drawer onto the runners Clip part number Detail of the clip with tool free integrated height adjustment. Clip part number Detail of the tool free integrated 3-way adjustment clip (height, depth and side adjustment). 23

24 24

25 Accessories 25

26 Accessories Drawer drilling templates for Unica runners Template for drawer drilling and 1 way adjustable clip fixing Clip part number Template for drawer drilling and 3 way adjustable clip fixing Clip part number Stabilizer for drawers - To be fitted on both right and left sides of the drawer - Cam adjustment to allow a perfect bearing of the wheels to the cabinet sides - Combined with Push runners it allows the opening also by pressing the extremities of the drawer - It improves the overall stability of the drawer DATA FOR ORDER PACKING Envelope with 2 pieces (2 mounting plates, 2 roller carriages and assembly instructions) PART NUMBER Box 300 pieces Ed. 01 D048DMS 26

27 Spacer for Unica runners Thickness 4,5 mm Thickness 6 mm DATA FOR ORDER Packing: 1 x 800 pieces DESCRIPTION PART NUMBER Spacer 4,5 mm Spacer 6 mm

28 ARTURO SALICE S.p.A. VIA PROVINCIALE NOVEDRATESE, NOVEDRATE (COMO) ITALIA TEL FAX DEUTSCHE SALICE GMBH RUDOLF DIESEL STR. 10 POSTFACH NECKARWESTHEIM TEL FAX DEUTSCHE SALICE GMBH VERKAUFSBÜRO NORD RINGSTRASSE 36/A30 CENTER LÖHNE TEL FAX SALICE FRANCE S.A.R.L. ROUTE DE GOA ZAC LES 3 MOULINS ANTIBES TEL FAX info.salice@salicefrance.com SALICE ESPAÑA, S.L.U. CALLE COPÉRNICO, 11 POLÍGONO INDUSTRIAL COLL DE LA MANYA GRANOLLERS (BARCELONA) TEL FAX info.salice@saliceespana.es SALICE UK LTD. KINGFISHER WAY HINCHINGBROOKE BUSINESS PARK HUNTINGDON CAMBS PE 29 6FN TEL FAX info.salice@saliceuk.co.uk SALICE AMERICA INC CROWN CENTRE DRIVE CHARLOTTE NC TEL FAX info.salice@saliceamerica.com SALICE CANADA INC SLADEVIEW CRESCENT UNIT # 7-9 MISSISSAUGA, ONTARIO L5L 5Y1 TEL FAX info.salice@salicecanada.com Ed 03-04/2013 We reserve the right to change the technical specifications.