Nelson Washbasin Pre-Install Instructions

Transcription

1 Nelson Washbasin Pre-Install Instructions Pre-Install Instructions Please see the below for instructions to prepare site for installation. This product is designed for indoor use in a wet environment, such as a bathroom or washroom. It may only be used in an environment corresponding to the system s IPX6 rating. Ensure that the installation location environment also complies with the following operating parameters: Tempreture - 5 C to 40 C, Relative humidity - 20% to 30 C (condensation free), Atmospheric pressure to 1060 hpa. Ensure a 230 volt (5 amps) fuse spur is installed by means of an approved moisture-resistant wall box (Fig 1.) or by leading an approved cable through the wall for connection outside the room (Fig 2.). The product is supplied with a plug attached, but this will need to be replaced with an IP-rated plug and socket combination appropriate to the location of the socket relative to moisture, or alternatively the product may be hardwired to a mains supply. All electrical connections are to be carried out by a qualified electrician. AC Power to be switched on in advance of OpeMed engineers arrival. All flooring must be level and complete. All walls must be decorated and complete (as per fixing instructions on page 3). Nelson Washbasin 1

2 Fig. 1 (Recommended) Fig. 2a Fig. 2b 666 (26 2 /8) Fig. 2c 170 (6 6 /8) Hot/Waste/Cold Feed Pipes (3) (3) 120 ) (46 /8 340 (13 /8 3 ) Fuse Spur Fig. 2a Fig. 2c Fig. 2b 2

3 Fixing Instructions See below for weight limits, fixing recommendations and requirements. The load on each anchor (screw) has been calculated, both for the product sustaining normal load and the product sustaining maximum load. You will find a list of different anchor types and the load they can sustain when fitted into different wall types and suggestions as to how to reinforce a plasterboard wall with plywood. Please note: These suggestions are to be considered as guidelines only. When loaded with Maximum load each anchor supports... When loaded with Maximum load incl. safety factor each anchor supports... Nelson Washbasin 150kg 20kg 225kg 30kg Maximum Load 2 - Wall Anchors Choosing the appropriate anchor for a specific type of wall Wall Type Fischer Type Anchor Type Maximum load Concrete >B25 SX12 Coach Screw 10x kg Concrete >B25 SX12 Bolt 10x kg Concrete >B kg Solid Brick >= Mz12 SX12 Coach Screw 10x80 75 kg Solid Brick >= Mz12 SX12 Bolt 10x70 75 kg Solid Brick >= Mz12 Solid Sand Lime Brick >= Hlz12 SX12 Coach Screw 10x kg Solid Sand Lime Brick >= Hlz12 SX12 Bolt 10x kg Solid Sand Lime Brick >= Hlz12 Hollow Brick >= Hlz12 SX12 Coach Screw 10x80 30 kg Hollow Brick >= Hlz12 SX12 Bolt 10x70 30 kg Hollow Brick >= Hlz12 Aerated Concrete P4 SX12 Coach Screw 10x80 50 kg Aerated Concrete P4 SX12 Bolt 10x70 50 kg Aerated Concrete P4 GB14 M10x kg Aerated Concrete P4 60 kg 3

4 Wall Anchors Continued... Hollow Sand Lime Brick >=KSL12 Hollow Sand Lime Brick >=KSL12 SX12 Coach Screw 10x80 40 kg SX12 Bolt 10x70 40 kg Plasterboard (2 x 12,5 mm) KD8 Toggle 39 kg Plasterboard (2 x 12,5 mm) water-resistant KD8 Toggle 58 kg Plasterboard (1 x 12,5 mm) re-enforced with 22 mm plywood KD8 Toggle 133 kg Plywood 22 mm KD8 Toggle 133 kg Chipboard 19 mm KD8 Toggle 86 kg Maximum Load 3 - Check List Recommended load if wall is built in compliance with national standards The OpeMed Nelson Washbasin is compatible with: Brick walls (solid brick or hollow brick) >Mz12 or >Hlz12 2 x1.5 studs, 22 mm plywood or equivalent 2x 12.5 mm plasterboard or equivalent Aerated concrete walls > G2 Concrete walls > B15 4

5 Maximum Load Reinforcements Reinforcements of walls should always comply with national standards Plasterboard 12,5 mm (x2) (water-resistant) Plywood 22 mm (x 2) Please refer to mounting instructions for indication of the placement in height of plywood plate. Plasterboard 12,5 mm (x2) Product Plywood 22 mm (x 2 so that tip of anchor is not exposed) Hollow between walls Screw to fit wall type (see page 2) Plasterboard (other side) Washer 5