SIMULATION PRE-INSTALLATION GUIDELINES CONTRACTOR REQUIREMENTS FOR ROOM PREPARATION
|
|
|
- David Lester
- 8 years ago
- Views:
Transcription
1 SIMULATION PRE-INSTALLATION GUIDELINES CONTRACTOR REQUIREMENTS FOR ROOM PREPARATION version 1.0_
2 TABLE OF CONTENTS INTRODUCTION 1 COMPONENTS-AT-A-GLANCE 2 SPACE DIMENSIONS 3 BACK WALL ASSESSMENT 4 PROJECTOR MOUNTING (CEILING) 5 PROJECTOR MOUNTING (SHELF) 6 PROJECTOR ELECTRICAL 7 CONDUIT PLACEMENT & INSTALLATION 8 COMPUTER ELECTRICAL 9 CLIENT / CONTRACTOR CHECKLIST 10
3 INSURING A SUCCESSFUL SIMULATION INSTALLATION This document is designed to provide a simple, visual overview of the key components necessary for completion in the designated simulation area BEFORE the installation of Foresight Sports Performance Simulator. Please provide this document to the contractor(s) responsible for all prepatory work that will be completed prior to the installation of the Foresight Sports Performance Simulator. Foresight Sports SIMULATION SOFTWARE INSTALLATION + QUICK START 1
4 ROOM COMPONENTS AT-A-GLANCE Pre-installation preparation work for the Foresight Sports Performance Simulator includes the following: Confirmation of the physical space DIMENSIONS for the Designated Simulation Area Assessment of BACK WALL structure Placement and Installation of the PROJECTOR MOUNT Placement and Installation of PROJECTOR ELECTRICAL service Placement and Installation of CONDUIT for video cords running from projector to computer Placement and Installation of WALL ELECTRICAL service for the computer that will run the Foresight Sports Simulation Software 2 FORESIGHT SPORTS
5 CONFIRMATION OF SPACE DIMENSIONS BACK WALL To properly and safely accommodate the Foresight Sports Performance Simulator, the intended area should have the following minimum dimensions: A HEIGHT MINIMUM of: A DEPTH MINIMUM of: A WIDTH MINIMUM of: 12 FEET 22 FEET 16 FEET These minimum requirements insure that all proper components can be correctly installed and safely utilized. PLEASE CONFIRM THESE ROOM DIMENSIONS PRIOR TO PROCEEDING. PRE-INSTALLATION SET-UP GUIDELINES 3
6 BACK WALL ASSESSMENT Back wall is made of: BACK WALL wood stud with drywall steel stud with drywall cinder block / concrete masonry / brick other: Depending on the nature of the simulation installation, the wall located directly behind the intended area for the simulation screen (BACK WALL) may be used for providing support and/or structural integrity to the simulation bay. To properly and safely accommodate the Foresight Sports Performance Simulator, the back wall should be assessed for structural integrity. PLEASE DETERMINE THE STRUCTURAL NATURE OF THE BACK WALL AND PROVIDE THIS INFORMATION TO FORESIGHT SPORTS PRIOR TO SIMULATOR INSTALLATION. 4 FORESIGHT SPORTS
7 PROJECTOR MOUNT PLACEMENT & INSTALLATION CEILING OPTION 1 foot from back wall to projector screen Must be RIGIDLY FIXED when installed feet from projector screen to front edge of mounting rod Mounting Rod pipe with 1.5 NPT Aligned to center of projection screen 10 feet from floor to bottom edge of mounting rod Proper placement and installation of the PROJECTOR MOUNT is critical to the utilization, accuracy and safety of the Foresight Sports Performance Simulator. To properly CEILING MOUNT the projector being utilized (Foresight Sports suggested projector is strongly recommended): follow the measurements for placement shown above. utilize the appropriate mounting pipe PIPE with 1.5 NPT (NATIONAL PIPE THREAD) insure that the installed pipe is RIGIDLY MOUNTED and PERPENDICULAR ( 90 ) to the floor. PRE-INSTALLATION SET-UP GUIDELINES 5
8 PROJECTOR MOUNT PLACEMENT & INSTALLATION SHELF OPTION 1 foot from back wall to projector screen feet from projector screen to front edge of shelf Must be RIGIDLY MOUNTED when installed 10 feet from floor to top edge of shelf Aligned to center of projection screen Proper placement and installation of the PROJECTOR MOUNT is critical to the utilization, accuracy and safety of the Foresight Sports Performance Simulator. To properly SHELF MOUNT the projector being utilized (Foresight Sports suggested projector is strongly recommended): follow the measurements for placement shown above. utilize a structurally appropriate 24 wide by 18 deep shelf insure that the installed shelf is safely secured and level. 6 FORESIGHT SPORTS
9 PROJECTOR ELECTRICAL NEEDS 110v outlet within 3 feet from projector mount The installed projector requires a 110v Outlet for power. A standard 110v outlet is recommended within 3 FEET of the projector mount for optimal safety and operation. PRE-INSTALLATION SET-UP GUIDELINES 7
10 CONDUIT PLACEMENT & INSTALLATION Conduit from projector mount to wall terminal near computer To manage the DVI cables that connect the projector to the computer that will run the simulation software, a CONDUIT LINE is required. The conduit line should follow these guidelines: the conduit line should be at least 2 IN DIAMETER the conduit line should terminate within 1 FOOT of the projector mount and computer area. should not exceed more than 40 LINEAR FEET in total length if installed within new construction, the conduit line should terminate in 4S TYPE JUNCTION BOXES no smaller than 4x4 in width/height. Junction boxes should accommodate a 2 conduit connection and fit within a 2x4 wall 8 FORESIGHT SPORTS
11 COMPUTER ELECTRICAL NEEDS two 110v x 15amp outlets within 6 FEET of computer area The COMPUTER area requires two 110v x 15amp outlets for power. These outlets are recommended within 6 FEET of the computer for optimal safety and operation. PRE-INSTALLATION SET-UP GUIDELINES 9
12 PRE-INSTALLATION CHECKLIST The following is a pre-installation checklist to ensure a quality installation. Please read the entire document carefully and sign and initials each item to confirm your compliance with the requirements. FORESIGHT SPORTS MUST RECEIVE THIS ENDORSED (INITIALED AND SIGNED) CHECKLIST BEFORE YOUR INSTALLATION CAN BE SCHEDULED. Client has confirmed the dimensions of the dedicated installation space. These dimensions are: Space width = ft in Space depth = ft in Space height = ft in Client has attached a diagram and photographs of the dedicated installation space. Client acknowledges responsibility for the removal of any suspended ceilings, display stands or any items or protrusions located in the dedicated space where the booth is to be assembled, prior to the arrival of the Foresight Sports installer. Client understands that a dedicated internet connection to the simulator computer is required to receive online technical support. Client understands that a dedicated 110volt x 15amp x 2 outlet power circuit must be within 6 (six) feet of the proposed placement of the simulator computer. Client understands that the simulation components will be delivered up to one week prior to the scheduled installation date. The freight company will call with an estimated delivery time. The customer/site manager is responsible for unloading the freight. Delivery drivers generally do not assist in the unloading of freight. The Client/site manager will provide 2 sturdy 6 ft. ladders (225 lbs rating) and 1 labor assistant with the ability to lift 50 lbs overhead. The Client/site manager acknowledges responsibility for all trash removal related to the completed installation. Customer Printed Name Customer Signature Date PLEASE SIGN AND FAX THIS PAGE TO FORESIGHT SPORTS AT If you have any questions regarding the aforementioned, do not hesitate to contact Foresight Sports. We will do our very best to provide you with all the information you may need to make your installation a success.
13 FS-SIM-IPG
14a. Hanging Sign Information. It Is The Responsibility Of The Exhibitor To Ensure Your Sign Conforms To All Published Rules And Regulations.
It Is The Responsibility Of The Exhibitor To Ensure Your Sign Conforms To All Published Rules And Regulations. 14a 1 Important Defined as any materials, including but not limited to, signs and machinery,
SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications includes all labor necessary to perform and complete such
Steel Door Frame Installation in Steel Stud Construction
Steel Door Frame Installation in Steel Stud Construction For use with the Steel Door Institute (SDI) video How to Install a Steel Door Frames in Steel Stud Construction This manual gives you step-by-step
installation guide ACTIV-1
installation guide ACTIV- Base foot. Leg x columns - right & left Motor unit. Work surface supporting bracket (Cantilever) x Control. box Base foot x Handset 4. Phase Motor unit Materials and Tools Hardware
FREEMAN LABOR JURISDICTIONS
UNION JURISDICTIONS for TAMPA, florida To assist you in planning for your participation in this upcoming exposition, we are certain you will appreciate knowing in advance that union labor may be required
ECM-D70T / ECM-D70T1.5
Elliptical Ceiling Dual Mount for 37 to 50 Flat Panels INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES 9531-041-001-01 Contents ECM-D70T / ECM-D70T1.5 Installation Tools... 3 Parts List...
TCTC Cabling Specifications
TCTC Cabling Specifications Purpose: To provide a standard specification that will be used for all Tri County Technical College (TCTC) facilities requiring structured cabling installation. Product specifications,
SECTION 02530 STORM DRAINAGE STRUCTURES. 1. Trench excavation, backfill, and compaction; Section 02250.
02530-1 of 5 SECTION 02530 STORM DRAINAGE STRUCTURES 02530.01 GENERAL A. Description Storm drainage structure construction shall include, but not necessarily be limited to, furnishing and installing or
GENERAL ELECTRICAL REQUIREMENTS
GENERAL ELECTRICAL REQUIREMENTS RECEPTACLE SPACING Within 6-feet of the edge of any door HABITABLE Not more than 12-feet apart along wall ROOMS: At all wall spaces 24 or more wide Within 24 of edge of
Lower Level (Level L) Exhibit Halls A, B & C
Floor Plans Wal t e r E. Was h i n g ton Con v e n t i on C e n t e r Lower Level (Level L) Exhibit Halls A, B & C Lower Level (Level L) Lower Level (Level L) Halls A, B & C Hall A 151,000 square feet
INSTALLATION GUIDELINES for SOLAR PHOTOVOLTAIC SYSTEMS 1
City of Cotati Building Division 201 W. Sierra Ave. Cotati, CA 94931 707 665-3637 Fax 792-4604 INSTALLATION GUIDELINES for SOLAR PHOTOVOLTAIC SYSTEMS 1 Any PV system on a new structures should be included
GENERAL WIRING RULES FOR HOUSES
GENERAL WIRING RULES FOR HOUSES 1. Romex has to be installed in drilled holes in joists or studs even above suspended ceilings - No stapling to bottom edges of joists or studs. You may staple wire to flat
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
EXHIBITOR BOOTH DISPLAY GUIDELINES
EXHIBITOR BOOTH DISPLAY GUIDELINES NAPE strives to provide each exhibitor with a reasonable sight line from the aisle. To help accomplish this, the following Guidelines for Booth Displays have been taken
BOOTH DESIGN RULES NEW! mgerald@eventsdc.com
BOOTH DESIGN RULES All exhibits must conform to the dimensions outlined below in order to assure ease of movement of participants and clear lines of visibility in the exhibit hall. For more information
Chapter 5 FLOOR LOADING AND WEIGHTS
Chapter 5 FLOOR LOADING AND WEIGHTS Section 1.0 Floor Loading Section 2.0 Seismic Data The CT system has a total floor load of approximately 6660 lbs (3021 kg). About 5050 lbs (2291 kg), including patient
ATS Overhead Table Shelf System INSTRUCTION MANUAL
ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship
Report on. Wind Resistance of Signs supported by. Glass Fiber Reinforced Concrete (GFRC) Pillars
Report on Wind Resistance of Signs supported by Glass Fiber Reinforced Concrete (GFRC) Pillars Prepared for US Sign and Fabrication Corporation January, 2006 SUMMARY This study found the attachment of
Minimum Standards for Data/Voice Infrastructure in New Building Construction
UNIVERSITY OF WATERLOO Minimum Standards for Data/Voice Infrastructure in New Building Construction 12/17/2012 Offices 1. Two Work Area Outlets (WAO) on opposite walls, each with 2 jacks 2. Each WAO shall
2. What building projects are exempted? (permit not required)
BUILDING AND SAFETY DEPARTMENT 1. What building projects require a permit? Following is a list of projects that require building permits based on Appendix chapter 1 of the California Building Code and
FREEMAN ELECTRICAL SERVICES FAQ s
FREEMAN ELECTRICAL SERVICES FAQ s From under carpet wiring to overhead lighting, Freeman has the power to simplify your electrical needs and installation. We ve answered your most common questions below
*Note: This document is an electronic (scanned) version of the original paper report and formatting may vary somewhat from the original.
Guideline No. 97-05 January 19, 1998 Version 1.0 Guideline for Stack Sampling Facilities* Prepared By: Kevin Reeve, B. Sc. Air Emission Specialist Environmental Operations Division Art Schultz, C.E.T.
IMPORTANT INSTRUCTIONS & OPERATING MANUAL. Houston 50 Inch Electric Wall Mounted Fireplace Black / White
IMPORTANT INSTRUCTIONS & OPERATING MANUAL Houston 50 Inch Electric Wall Mounted Fireplace Black / White Model Number:MFE5050BK Model Number:MFE5050WH Read these instructions carefully before attempting
Cabinets 101: Configuring A Network Or Server Cabinet
Cabinets 101: Configuring A Network Or Server Cabinet North, South and Central America White Paper May 2012 www.commscope.com Contents Background Information 3 What is a network or server cabinet? 3 What
EXHIBITION DISPLAY RULES
RULES AND REGULATIONS It is the responsibility of the exhibiting company to comply with SPIE rules and regulations Non-compliance may require modifications at the exhibitor s expense SPIE Exhibition Management
Cooktop Low-Profile Ventilation Hoods
INSTALLATION GUIDE Cooktop Low-Profile Ventilation Hoods Contents Wolf Cooktop Low-Profile Ventilation Hoods........ 3 Cooktop Low-Profile Hood Specifications.......... 4 Cooktop Low-Profile Hood Installation............
Electrical. This section applies to the design and installation of building power distribution systems.
Basis of Design This section applies to the design and installation of building power distribution systems. Design Criteria This section contains the architectural, structural and mechanical provisions
Anthro Tablet Charging Cabinets
Owner's Manual for Anthro Tablet Charging Cabinets Covers part numbers beginning TAB16 and TAB20. Components at a Glance The open views of the front and side of the cabinet below are for the TAB20 cabinet.
Laboratory Construction Guidelines Vicon MX Systems
Laboratory Construction Guidelines Vicon MX Systems These Vicon MX Laboratory Construction Guidelines illustrate how to prepare a life sciences laboratory for installation of your new Vicon MX motion measurement
EXHIBITION DISPLAY RULES
RULES AND REGULATIONS Responsibility of the exhibiting company to comply with SPIE rules and regulations. Non-compliance may require modifications at the exhibitor s expense SPIE Exhibition Management
EXHIBIT DISPLAY GUIDELINES
EXHIBIT DISPLAY GUIDELINES The following Guidelines for Display Rules and Regulations have been established by the International Association of Exhibitions and Events (IAEE). Guidelines for Display Rules
CABLE SUPPORT SYSTEMS
CABLE SUPPORT SYSTEMS eaturing the CADDY CAT HP J-Hook System Why CADDY CAT HP? Why Choose CADDY CAT HP over tray? ast and Easy to Install Much faster installation compared to conventional cable or ladder
SMEMA Surface Mount Equtpment Manufacturers Association
SMEMA Surface Mount Equtpment Manufacturers Association SMEMA Mechanical Equipment Interface Standard Introduction The SMEMA machine interface standards were developed to facilitate the interface of equipment
Standard electrical will be provided by the Gaylord National; however, extension cords or power strips are highly reccomended.
SERVICE INFORMATION BOOTH EQUIPMENT HIMSS MEDIA - BIG DATA & HEALTHCARE ANALYTICS FORUM JUNE 4-5, 2013 GAYLORD NATIONAL RESORT & CONVENTION CENTER NATIONAL HARBOR, MARYLAND Each 8' x 10' booth will be
March 14, 2007. Installation of Bay, Bow and Garden Windows
March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed
EXHIBIT/BOOTH SPECIFICATIONS
BOOTH SPECIFICATIONS Please review the following booth specifications to ensure that your display meets the Exhibit/Booth Guidelines. All booths, regardless of size, are required to follow these guidelines.
JELCO EZ-LIFT & RotoLift Lift Cases
JELCO EZ-LIFT & RotoLift Lift Cases RENTAL TRADE SHOWS EVENT MARKETING HOTEL SERVICES CORPORATE GOVERNMENT EDUCATION MILITARY WORSHIP SPORTS COMMAND CENTERS DIGITAL SIGNAGE TRAINING ROOMS VIDEO CONFERENCING
Chapter 36 - STRAW BALE CONSTRUCTION SECTION 3601 - PURPOSE. SECTION 3602 - SCOPE. SECTION 3603 - DEFINITIONS.
Austin City Code - Volume II TITLE 25 LAND DEVELOPMENT\CHAPTER 25-12 TECHNICAL CODES\ARTICLE 1: UNIFORM BUILDING CODE\25-12-3 LOCAL AMENDMENTS TO THE BUILDING CODE Chapter 36 - STRAW BALE CONSTRUCTION
SAME JETC May 22-25, 2012. St. Louis, Missouri IMPORTANT
18a Electrical Terms and Conditions IMPORTANT Please read the list of work below. If you require any of this work to be performed in your booth space, it must be performed by a show electrician. This work
Builder Specifications for Solar Ready Homes
Builder Specifications for Solar Ready Homes This document specifies the essential elements required to make a new home ready for the future installation of roof-mounted solar domestic hot water and photovoltaic
GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables
Engineering Department SEPTEMBER, 2007 GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables General Requirements This section applies to all public and private utilities,
Kitchen & Bath Measurements Guide
Kitchen & Bath Measurements Guide High End design without High End pricing Kitchen & Bath Measurement Guide ABOUT US Interstock Premium Cabinetry (IPC) is a manufacturer and importer of kitchen cabinets
SITE REQUIREMENTS AND INSTALLATION INSTRUCTIONS
ADVANTAGE PLUS SITE REQUIREMENTS SITE REQUIREMENTS AND INSTALLATION INSTRUCTIONS 50096-927 Rev A For additional information contact your Medivators Pg 1 of 18 SITE REQUIREMENTS The purpose of this section
AMS 120. EFT Guest Card Terminal & Refund unit
AMS 120 EFT Guest Card Terminal & Refund unit ACCOUNT MANAGEMENT STATIONS Wall mounted kiosk offering Visitor card purchase and refund Card deposit EFT purchase, refund and loading Full statement facilities
Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors
Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...
Trundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds)
Bunk Beds Unlimited Trundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds) On the following pages we have included all of the necessary drawings and requirements for a Modified twin-size
UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video
UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video http://bit.ly/9ywwh! CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL
Art Basel Miami Beach Dec 3 6 2015 Booth Design Regulations
1 6 1 BOOTH CONSTRUCTION The Art Basel in Miami Beach form an integral part of the contract between the exhibitor and Art Basel U.S. Corp. (see Art Basel in Miami Beach Exhibition Regulations). The following
necessary for years of satisfactory service. SmartBlock insulating form concrete walls share the
Chapter 7 PLUMBING AND ELECTRICAL 7.1 Introduction to Plumbing and Electrical Consideration of support services such as plumbing and electrical systems from the preliminary schematics phase through final
FIX TURE CARRI ERS. 140(a) MPB-2011-USA
FIXTURE CARRIERS STRUCTURAL FEET The feet are heavy duty cast ductile iron and invertible. No distinction is necessary between right and left hand. Each foot wraps around the specially formed edge of the
Vision Engravers and Routers PRE-Installation Guide. 2015 Vision Engraving & Routing Systems
Vision Engravers and Routers PRE-Installation Guide Revised: 8/19/2015 Vision Engravers and Routers PRE-Installation Guide All rights reserved. No parts of this work may be reproduced in any form or by
WHY CABLE TRAY? BECAUSE A CABLE TRAY WIRING SYSTEM PROVIDES SAFE AND DEPENDABLE WAYS TO SAVE NOW AND LATER
Large numbers of electrical engineers have limited detail knowledge concerning wiring systems. There is the tendency by engineers to avoid becoming involved in the details of wiring systems, leaving the
HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES
HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES 101 Retrofits Required. Pursuant to Section 553.844 553.884, Florida Statutes, strengthening of existing site-built,
DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION 17650 SECURITY SYSTEMS
PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. Inspections and observations by the Owner do not relieve the A/E of contract responsibilities. B. Chain of command 1. The DPS Project Manager is
10' 16' Maximum. Backwall 5' 5'
Peninsula December 11 13, * ALL PENINSULA EXHIBITORS ARE REQUIRED TO SUBMIT ACCURATE RENDERINGS AND DIMENSIONS OF THE PENINSULA EXHIBIT TO TRADE SHOW MANAGEMENT FOR APPROVAL PRIOR TO THE SHOW. (For questions,
CHAPTER 2 QUANTITY TAKE-OFF
CHAPTER 2 QUANTITY TAKEOFF The quantity takeoff is an important part of the cost estimate. It must be as accurate as possible and should be based on all available engineering and design data. Use of appropriate
Batibox TM flush-mounting boxes for dry partitions
flush-mounting boxes for dry partitions 800 51 800 42 800 53 800 54 800 42 + 800 71 800 77 Cat.Nos 1-gang boxes For 1 module 20 800 40 Drilling diameter 32 mm Depth 40 mm For 1 gang or 2 modules For wiring
2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property
2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property A brief summary of the most used code references for residential wiring State of Idaho Division of Building Safety Electrical
Mobile Home Pre-Inspection Checklist
Mobile Home Pre-Inspection Checklist TWO (2) STEP INSPECTION PROCESS STEP ONE: CALL FOR THE FIRST INSPECTION WHEN THESE ITEMS ARE COMPLETE. 1. Septic tank installed and plumbing complete. (SEE PLUMBING
Electrical for Detached Garages: Updated Feb 19, 2016 for 2015 CE Code in force Jan. 1, 2016. Underground branch circuit feeding a detached garage:
Electrical for Detached Garages: Updated Feb 19, 2016 for 2015 CE Code in force Jan. 1, 2016 * Garage construction requires permits (electrical, building) * Permits must be applied for at the time. * Dial
Materials. Estimating Steel. Players. Materials. Shop Drawings. Detailing Process. Standard shapes. Fabricated members, Built-up sections
Materials Standard shapes W sections, C channels, Structural T, Angles, Pipes, Tubes, Rods and Plates Fabricated members, Built-up sections Adding plates to beam flanges, Stiffeners to beam webs Built
UL 580 TEST REPORT. Rendered to: ARMSTRONG WORLD INDUSTRIES. SERIES/MODEL: MW Vector PRODUCT TYPE: Ceiling System, 3' OC
UL 580 TEST REPORT Rendered to: ARMSTRONG WORLD INDUSTRIES SERIES/MODEL: MW Vector PRODUCT TYPE: Ceiling System, 3' OC Report No.: Test Dates: 12/14/09 Through: 12/22/09 Report Date: 03/12/10 Expiration
Production Services Department
Production Services Department Welcome to the Bellagio Meeting and Convention Center. As you begin planning for your event, allow Bellagio s Production Services Department to assist you with all of your
Pro-Lift Steel Pile Foundation Repair
Pro-Lift Steel Pile Foundation Repair Pro-Lift Steel Pile Foundation Repair System Pro-lift steel piles are designed for the stresses of Texas soils. They can have multiple steel walls, depending on the
[see Figure 3 below] Ferrite tile walls and ceiling RF Absorber parcel walls and ceiling Removable floor section to make fully anechoic
![[see Figure 3 below] Ferrite tile walls and ceiling RF Absorber parcel walls and ceiling Removable floor section to make fully anechoic](/thumbs/32/15421143.jpg "[see Figure 3 below] Ferrite tile walls and ceiling RF Absorber parcel walls and ceiling Removable floor section to make fully anechoic")
Test Room ID: R21F Description: SEMI ANECHOIC SHIELDED TEST ENCLOSURE Primary Testing Uses: FCC, CE Mark Dimensions: 9.75m x 6.10m x 5.49m (32ft. x 20ft. x 18ft.) [see Figure 3 below] Construction: Galvanized
Gas Meter Clearances and Service Installation Requirements
March 2016 Gas Meter Clearances and Service Installation Requirements Builder/Owner/Developer Requirements Call PSE's Customer Construction Services 1 888 321 7779 or visit PSE.com/CustomerConstruction
DESIGN GUIDELINES. Local Area Network
DESIGN GUIDELINES Local Area Network The total oversight and management responsibilities for information assurance (IA) and protection of DoDEA s critical infrastructure fall under the purview of the DoDEA
RESOURCES. Telehealth. Provincial Health Services Authority. Telehealth & General Meeting Room Design Requirements
RESOURCES Telehealth Provincial Health Services Authority Telehealth & General Meeting Room Design Requirements Prepared by IMITS, LMC Telehealth and C&W Media Services December, 2013 Revised, August 2014
ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start. Unitec www.startwithunitec.com
ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start Unitec www.startwithunitec.com Proprietary Information and Materials of Unitec, Inc. Such proprietary information and materials
Installation Instructions For Slider Casement Air Conditioners
Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT
ELECTRICAL GUIDELINES FOR SINGLE-FAMILY HOME OWNERS:
ELECTRICAL GUIDELINES FOR SINGLE-FAMILY HOME OWNERS: Chapter 12 of the Burlington Code of ordinances allows owner occupants of single family homes to do their own wiring if they choose. If you choose to
MHI. Overview of Manufactured Home Installation MANUFACTURED HOUSING INSTITUTE. This guide contains an overview. of the HUD-Code manufactured home
MANUFACTURED HOUSING INSTITUTE Overview of Manufactured Home Installation This guide contains an overview of the HUD-Code manufactured home installation process. This is only a guide, and it is recommended
PUBLIC RESTROOMS, DESIGN INTENT
PUBLIC RESTROOMS, DESIGN INTENT 1.01 STRUCTURAL A. Where feasible, metal stud partitions will be constructed on a 6 high concrete curb. 1.02 MECHANICAL A. Restrooms will have a minimum of 15 air changes
Seven. Easy Steps. Your Own Walkway, Without Mortar. or Concrete. to Installing. Driveway and Patio
Seven Easy Steps to Installing Your Own Walkway, Driveway and Patio Without Mortar or Concrete Brick is one of the world s oldest and most enduring building materials. Those same qualities also make it
City of Riverside Building & Safety Division Residential Electric Vehicle (EV) Charger Guidelines
Western Riverside County Code Uniformity Program City of Riverside Building & Safety Division Residential Electric Vehicle (EV) Charger Guidelines PHONE (951) 826-5697 3900 Main Street, Riverside, CA 92522
Truck Company Operations
Truck Company Operations Instructor Guide Session Reference: 1-1 Topic: Salvage Level of Instruction: Time Required: 2 Hours Materials: Various Items of Salvage Equipment Salvage Covers References: Ladder
GROWTH MANAGEMENT DEPARTMENT 201 SE 3 rd ST, (Second Floor), Ocala, FL 34471 (352) 629-8421; FAX: (352) 629-8264
BUILDING CODE GUIDELINES FOR ELECTRICAL INSPECTIONS Building Code compliance is the obligation of design professionals and/or contractors. Plan Review and Inspection Guidelines are intended to be used
Lighthouse Engineering, L.L.C.
Registered Engineering Firm (F: 9334) Phone: 214-577-1077 Fax: 214-224-0549 Website: www.lighthouseeng.com Email: Office@LighthouseEng.com Thursday, September 04, 2014 TO: Our Client RE: Initial Engineering
Gas Meter Clearances and Service Installation Requirements
March 2015 Gas Meter Clearances and Service Installation Requirements Builder/Owner/Developer Requirements Call PSE s Customer Construction Services 1-888-321-7779 or visit PSE.com/CustomerConstruction
Whitepaper. Modular Substation Cable Termination Design. Author: Allan Bozek P.Eng, MBA, EngWorks Inc, Calgary, Canada
Whitepaper Modular Substation Cable Termination Design Author: Allan Bozek P.Eng, MBA, EngWorks Inc, Calgary, Canada Abstract The methods for cable penetrations into modular industrial substations are
P KILNS BUILT TO LAST DELIVERY AND INSTALLATION CHECKLIST AND ACCEPTANCE FORM FOR HERCULES & EASY-LOAD FRONT-LOADING KILNS
P KILNS BUILT TO LAST L&L Kiln Mfg. Inc. 505 Sharptown Rd. Swedesboro, NJ 08085 856.294.0077 Fax: 856.294.0070 sales@hotkilns.com Web: hotkilns.com DELIVERY AND INSTALLATION CHECKLIST AND ACCEPTANCE FORM
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
Detection System Model 3800 Series
Detection System Model 3800 Series Architect/Contractor Information Package 3M Library Systems 3M Center, Building 225-4N-14 St. Paul, Minnesota 55144-1000 Copyright 2001-2006 3M. All rights reserved.
INSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
Guidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
SPECIFICATIONS FOR THE INSTALLATION OF FIRE ALARM SYSTEMS, SPRINKLER SYSTEMS, AND MASTER BOXES IN THE POQUONNOCK BRIDGE FIRE DISTRICT
SPECIFICATIONS FOR THE INSTALLATION OF FIRE ALARM SYSTEMS, SPRINKLER SYSTEMS, AND MASTER BOXES IN THE POQUONNOCK BRIDGE FIRE DISTRICT The purpose of these specifications is to insure that there are minimum
Envelope INSULATION BATT (2) Avoid Using Batt Insulation With Metal Framing. Pressure or Friction Fit
R-H-DI1 INSULATION BATT NR-E-IB1 Avoid Using Batt Insulation With Metal Framing Batt insulation should not be used with metal framing systems. Although it is common to see fiberglass batt insulation installed
800 Communications Circuits
ARTICLE 800 Communications Circuits INTRODUCTION TO ARTICLE 800 COMMUNICATIONS CIRCUITS This article has its roots in telephone technology. Consequently, it addresses telephone and related systems that
InstaPATCH ZERO Solution Guide
SYSTIMAX Solutions InstaPATCH ZERO Solution Guide Rapid Server Deployment and Change Management North, South and Central Americas 1 As data centers face ever-increasing IT demands, growth demands and evolving
Architect/Contractor Information Package
Architect/Contractor Information Package 3M SelfCheck System C-Series C1 Model 877 This package provides architects and contractors with the information necessary for the successful installation of the
Utility Department 317-262-3467 utilities@icclos.com. City/ Province. State, ZIP, Country
Utility Department 317-262-3467 utilities@icclos.com Order Online at http://www.icclos.com or FAX with complete credit card information or purchase order to 317-262-3419 OR Mail completed form with check,
Solar Panel Installations
Solar Panel Installations Page 1 of 6 SINGLE-FAMILY RESIDENTIAL CHECKLIST City of Hayward Development Services Department Revised: 7-09-15 PERMIT REQUIREMENTS Permits are required for all solar panel installations.
Electrical Wiring Technical Bulletin
Electrical Wiring Technical Bulletin Overview In general, SIP construction is easier and more cost effective when things are planned and thought out before the panels are manufactured. This process will
7. PRINCIPAL STEPS 8. POTENTIAL HAZARDS 9. RECOMMENDED CONTROLS
ACTIVITY HAZARD ANALYSIS (AHA) 1. Contract Number: 2. Contractor Name: 3. Date prepared: 4. Title/Activity Performed: FIXED SCAFFOLDING 5. Location: 6. Estimated Date of Completion: 7. PRINCIPAL STEPS
EXHIBIT CONSTRUCTION GUIDELINES
EXHIBIT CONSTRUCTION GUIDELINES STANDARD BOOTH DEFINITIoN: Exhibit consisting of one or more standard units in a straight line. be permitted to a maximum height of 8 3 (2.5m). INTENT If a portion of an
SECTION 02150 REMOVAL OR ABANDONMENT OF EXISTING UTILITIES AND UNDERGROUND STRUCTURES. 1. Trench excavation, backfill, and compaction; Section 02250.
02150-1 of 6 SECTION 02150 REMOVAL OR ABANDONMENT OF EXISTING 02150.01 GENERAL A. Description Removal or abandonment of existing utilities and underground structures shall include, but not necessarily
Component Series Racks... 1 2 Component Series Rack Plus Bundles...3 Component Series stackable skeleton Racks...4
SANUS RACKS Table of Contents Component Series Racks... 1 2 Component Series Rack Plus Bundles...3 Component Series stackable skeleton Racks...4 sanus EcoSystem... 5 6 sanus EcoSystem Bundles...7 Rack
2. Division 05 Structural Steel Framing for steel framework requirements
SECTION 131200 - CLIMBING WALLS PART 1 GENERAL 1.1 SUMMARY A. This section includes the following: 1. GFRC Rock Realistic Climbing Wall System B. Related Sections 1. Division 04 Unit Masonry 2. Division
GE Lighting Solutions. Albeo LED Luminaire. Modular High & Low Bay Lighting. (ABHX - Series) imagination at work
GE Lighting Solutions Albeo LED Luminaire Modular High & Low Bay Lighting (ABHX - Series) imagination at work Product Features The award winning Albeo ABHX-series LED Luminaire utilizes innovative heat-sinking
CERTIFICATE OF APPROVAL No CF 5055 ARABIAN VERMICULITE INDUSTRIES
CERTIFICATE OF APPROVAL No CF 5055 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of 1 st Industrial Area,