How to Construct the 8-Point Star by Jay S. Helland
|
|
- Gordon Lawrence
- 7 years ago
- Views:
Transcription
1 How to Construct the 8-Point Star by Jay S. Helland The photos in these instructions were not taken to provide the reader the general idea of the processes used and does not follow the order of one medallion from start to finish. The process for constructing an 8-pt. star medallion is as follows: 1. Rip contrasting colored wood strips 3/8 to ½ wide by ¾ thick and about 12 to 24 in length (depends on how many stars you want to make). Cut and additional strip of wood for layout purposes. 2. Cut a 45 degree miter on the end of each strip of wood either on the table saw or miter box saw. 3. Layout: the 8 pt. star segments are parallelograms, so lay one of the other strips on top making sure the edges are flush with the miter cut. This is where the additional strip of wood the exact thickness is a huge help. (See Photo) 4. How to create the parallelogram segment. Scribe with a sharp pencil or knife the size of the segment, which is the width of the stock. Layout of Parallelogram Segment A pencil was used to highlight the scribed line.
2 5. There are three ways to cut out the star segments but they all start by cutting a 45 degree angle on the table saw or miter box saw. First method; cut a 45 degree angle on the end of the board. Layout the parallelogram and rough cut on of the stars segments on the band saw and grind down to the layout line using the disc sander. This method will require you to re-cut the 45 degree miter for each segment and repeat the layout. Second method uses a band saw miter gauge sled (see photo). Lightly sand the band sawed surface before gluing. Trust me you can get a very suitable surface using a band saw. Using a disc sander, sand to the layout line. Third method uses the table saw with a miter sled. Set a stop block on the wooden fence so that the cutting process is repeatable. Band Saw Sled Table Saw Sled 6. Glue two of the segments together unit there are 4 pairs. After the glue sets up, glue the two pairs together to create two halves. You should always lightly sand any glue off the surfaces to keep flush for the next glue ups.
3 7. Infill Process: Now that you have an 8 point star you are ready to begin infilling with the contrasting colored wood. Lay the star on top of the wood to be used as the infill material and scribe the joint. Rough cut the wood on the band saw and then sand to the scribed line using your disc sander. Check the accuracy of the cut by back-lighting the piece checking for gaps. If the fit of the intersection is acceptable, glue the in-fill. I use rubber bands for the clamps. Repeat the process until all gaps are in-filled. Lightly sand as needed to keep both surfaces flat throughout the process. 8. Using a compass draw a circle on the glue up onto what I call the hockey puck. Rough cut on the band saw to create the circle.. 9. Sand the top and bottom sides of the assembly on the disc sander. It s important to get the two faces parallel to each other. Use a veneer height gauge or at depth gauge to scribe the edge of the accessibly and then sand the face until it is parallel.
4 10. Using 1/8" Baltic Birch plywood, glue the plywood to both sides of the hockey puck (making a sandwich) be sure to keep the sides and edges square to each other. I use a small square and the fence of my jointer or table saw to align it. Hold the assembly by hand or a spring clamp until the glue gets tacky enough that it won t get out of square while you place some additional spring clamps on the assembly. 11. After the glue has dried, resaw on the band saw so that you have cut a 3/16" thick segmented inlay. 12. Smooth the band sawed face of the hockey puck on the disc sander keeping the two faces parallel. 13. Glue another piece of 1/8 Baltic birch plywood to the hockey puck making another sandwich and repeat steps 10 and 11. It is possible to get 3 segmented inlays pieces out of one hockey puck.
5 14. Center the medallion on the long axis of the lathe (see photo) and then draw a circle on the wooden faceplate around the rough circumference making sure that there is a registration mark. Remove the faceplate from the lathe and place two or three 1/8" glue dots (CA or yellow/white glue) on the back of the medallion. Using the layout lines, center the star on the faceplate and clamp letting the glue dry for at least 45 minutes if you used white of yellow glue. Make sure that the faceplate you are using has been faced off and is clean of debris before gluing on the medallion. Formatted: Font: (Default) +Body, 11 pt, Font color: Auto 15. Place the faceplate back on the lathe and with a parting tool or skew lathe chisel cut into the medallion from the face but not the side. Cutting from the face of the medallion will make it symmetrical without creating the shear stress that cutting from the edge will create.
6 16. Using a putty knife or 5 in 1 tool, separate the medallion from the face plate. Sand off glue from the back of the medallion. 17. Once you get the medallion round you're ready to cut the recess in the bottom to receive the medallion. The recess depth should be at least as deep as the thickness of the medallion. 18. Turn a mortise in the bowl bottom the exact same diameter of the medallion.
7 The photo below is how to registering the bowl bottom on the lathe before gluing it to the wooden faceplate.
8 19. This photo below illustrates how the bottom and the bowl match before gluing. The tenon has been turned to fit the mortise in the bottom of the bowl. Clamping Technique Using Weights
9 The photo above shows the bowl ready for facing off the top rim before the top ring is glued to the bowl. More Medallion Designs to Consider The Completed Project!
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationSEGMENTED WOODTURNING
Notes on: SEGMENTED WOODTURNING Malcolm Tibbetts www.tahoeturner.com malcolm@tahoeturner.com (530) 541-6135 MATHEMATICAL FORMULAS AND CONCEPTS: A circle contains 360 Circumference = Diameter x π(3.1416)
More informationThe tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results
Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationRaised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set
Raised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set Congratulations on your purchase of Freud s world class 2 + 2 Raised Panel Bit Set. This revolutionary design combines two small wings
More informationBuild a Precision. Crosscutting Sled
Build a Precision Crosscutting Sled On-the-money, splinter-free crosscuts are well within your grasp using most well-made tablesaws, but you do have to do a few things to ensure great results cut after
More informationSHELVES. www.tedswoodworking.com
SHELVES It's rare that bookshelves look as interesting as the objects you display on them. After all, how much can you decorate the edges of your shelves and sides? This unit is unusual because the shelves
More informationHive Top Ventilation Shims
Hive Top Ventilation Shims When preparing your bee hives for the winter, it is very important to provide for ventilation at the top of the hive. Through out the winter, the bees are expelling a lot of
More informationMaking Wooden Hinges
Making Wooden Hinges By Alex Reid - www.mokkou.jp Materials and tools used - 3.2mm straight router bit - 1/8 round-over router bit - Flush-cut straight bit (with bearing on bottom) - Finger-joint jig -
More informationThe Hive Bodies. In the Beekeeper s Work Shop. Building a Bee Hive: The Hive Bodies. by Stephen E. Tilmann
The Hive Bodies In the Beekeeper s Work Shop The hive body is the heart of a managed bee hive colony (Figure 1). It is where the queen lays her eggs, the house bees raise the brood and the workers store
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationHONING LATHE DUPLICATOR CUTTERS
Lay the flat face of the cutter or bit on the flat top surface of the hone with the rest of the cutter overhanging the edge. Rub the cutter or bit up and down the hone (Figure 24-44). Be sure to hold the
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationDining Tables by Kim Carleton Graves
This is an excerpt from the book Dining Tables by Kim Carleton Graves Copyright 2001 by The Taunton Press www.taunton.com Vineyard Table The vineyard table is almost as old a design as the trestle table,
More informationPart 1: Cut Accurate Segments. Segmented Turning School. By Jim Rodgers
Part 1: Cut Accurate Segments Segmented Turning School By Jim Rodgers 24 American Woodturner Winter 2005 Reprinted with permission American Association of Woodturners Ready to try your hand at segmented
More informationHOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY
HOW-TO HOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY Most floor coverings, if laid over uneven wooden floors, will wear unevenly and look unsightly. The answer is to cover the old boards with hardboard
More informationFREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Tools and Glue. Required Materials
Do not try to make your ornithopter using "household materials". If you want it to fly, you have to build it right. FREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Wingspan: 16 inches Weight: 1/4 ounce The Ornithopter
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationTOOLS FOR SELF RELIANCE REFURBISHING SHEET No 2. Registered Charity No 280437. Saws for Woodworking
Registered Charity No 280437 Saws for Woodworking Issued December 2002 Registered Charity No 280437 page no 1 SAW TYPES Rip saw For cutting along the grain Crosscut saw [A smaller version is known as a
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationThe Basics of Stave Segmented Turning
The Basics of Stave Segmented Turning Notes by Jim Rodgers Version 1.2 February, 2005 JL Rodgers, Incorporated 36 Briar Drive Martinez, CA 94553 9925) 229-5773 The Basics of Stave Segmented Turning Requirements
More informationThese instructions will show you how to install an internal door into a non-loadbearing partition wall. The instructions are split into three parts.
No 8 in the series of 'How to' brochures produced by PlaceMakers, New Zealand How to Frame and Hang a Door These instructions will show you how to install an internal door into a non-loadbearing partition
More informationTaking Wainscot Up Stairs
Taking Wainscot Up Stairs raised MDF panels and stock moldings bring this elegant trim detail to the rest of the house BY GARY STRIEGLER I credit a lot of the success of my business to the trimwork we
More informationSTAIR TREAD & RISER INSTALLATION GUIDELINES
STAIR TREAD & RISER INSTALLATION GUIDELINES ARTISTIC FINISHES DOES NOT WARRANTY THE COMPLETENESS OR ACCURACY OF ANY INSTALLATION. THE INSTALLATION CONTRACTER MUST HAVE THE EXPERIENCE AND KNOWLEDGE TO COMPLETE
More informationYou can copy, share or publish this document without changing this page and document content. Contact information eacubukcu@yahoo.
This is a traditional japanese puzzle box. But I prepared this document. All the copyrights of this docoments belongs to me. Document copyrights Erhan Çubukcuğlu 2015 You can copy, share or publish this
More informationAssembly Instructions Basic Folding-Leg Box Frame Style
Assembly Instructions Basic Folding-Leg Box Frame Style Basic Folding Leg Cornhole Board Concept 1 2 12 3 1 2 3 15 16 4 1 4 52 9 R1 3 4 6 21 48 12 1 4 Bolt Washer 9 13 16 35 Washer Double Nut CornholePlayers.net
More informationPicnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
More informationWine Rack & Glass Storage Bench Chris Gardner
Wine Rack & Glass Storage Bench Chris Gardner Quantity Length Width Material Part 2 48 16 3/4 birch plywood top, bottom 2 14 16 3/4 birch plywood sides 2 14 13 3/4 birch plywood support dividers 2 3 15
More informationWHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationGear PEPSI CAN STOVE INSTRUCTIONS
Gear PEPSI CAN STOVE INSTRUCTIONS [NOTE: Updated Instructions are now available. The new stove is less likely to develop flame leaks and the fuel/air mixture is improved. Instructions for a simmer ring
More informationSHOP NOTES METAL SHAPER FOR YOUR SHOP
SHOP NOTES METAL SHAPER FOR YOUR SHOP A METAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationPole Lathe and Shave Horse Design
Pole Lathe and Shave Horse Design These pictures and accompanying words are Copyright Michael Hughes February 2002. They are not to be re-produced, in part or whole, without permission from the author.
More informationDINING OUT. Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson
DINING OUT Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson http://popularmechanics.com/home_improvement/furniture/2001/4/table_and_bench_set/print.phtml
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationHow to Install Hardwood Flooring Over a Sub Floor
How to Install Hardwood Flooring Over a Sub Floor Installation Preparation Instructions Read the entire instructions before starting your project. 1) INSPECT EACH PLANK (see fig. a) Wood is a natural product
More informationPROJECT PLAN. Stackable shelves
PROJECT PLAN Stackable shelves This article originally appeared in The Family Handyman magazine. For subscription information, visit www.familyhandyman.com Please note that pages that appeared in the magazine
More informationComplete Dovetail Jig Instructions
Complete Dovetail Jig Instructions 18 15 1 12 13 8 (22818) 19 17 16 4 3 6 14 5 9 9 11 10 2 PARTS LIST - COMPLETE DOVETAIL JIG Introduction Your new dovetail jig will cut Full Through Dovetails and three
More informationShape Dictionary YR to Y6
Shape Dictionary YR to Y6 Guidance Notes The terms in this dictionary are taken from the booklet Mathematical Vocabulary produced by the National Numeracy Strategy. Children need to understand and use
More informationActivity Set 4. Trainer Guide
Geometry and Measurement of Solid Figures Activity Set 4 Trainer Guide Mid_SGe_04_TG Copyright by the McGraw-Hill Companies McGraw-Hill Professional Development GEOMETRY AND MEASUREMENT OF SOLID FIGURES
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationPanel/Hand Saw Kit Assembly Instructions
Panel/Hand Saw Kit Assembly Instructions PLEASE READ THE FOLLOWING INSTRUCTIONS BEFORE BEGINNING Brief Summary You will be performing the following Tasks: 1. Determining the degree of shaping laying out
More informationIntroduction to Door Construction
Entry Door Construction Made Simple with Freud s Entry & Interior Door Router Bit System Congratulations on your purchase of Freud s Entry & Interior Door Router Bit System. This unique set allows you
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationWoodturning Project Tutorials by Larry Hancock. 2004, 2005 Larry Hancock, turnedtreasures.com. Gavel Turning
Woodturning Project Tutorials by Larry Hancock 2004, 2005 Larry Hancock, turnedtreasures.com Gavel Turning Before you can start to turn a gavel the design, size, and wood need selected. The design I used
More information30a. 31a. 30b 12. 31b. 29a 28a 1/48SCALEHEMSDAUPHIN PAGE2/10
9 11 10 43 42 49 50 32 7 51 52 48 58 5 6 8 59 2 3 4 1 24 30a 31a 30 30b 12 31b 31 28 13 29 29a 28a 1/48SCALEHEMSDAUPHIN PAGE2/10 38 82 38f 85 84 86 83 37d 35 38a 37 60 17 21 20 16 15 87 27 34 40c 36b 36a
More informationa Wall Railing Hanging Get it at the right height and make sure it's fastened to the framing; someone's life may depend on it Handrails and code
Hanging a Wall Railing Get it at the right height and make sure it's fastened to the framing; someone's life may depend on it BY SEBASTIAN EGGERT Handrails and code A graspable handrail is required for
More informationStar Trek: The Motion Picture Tricorder
#PRP1786 Star Trek: The Motion Picture Tricorder Prop Kit Assembly Manual For the first time ever, Roddenberry.com is pleased to introduce the Star Trek: The Motion Picture Tricorder build it yourself
More informationThe "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.
The "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.com (c) 2/20/03 The David steam engine is a simple oscillating steam engine, many plans
More informationMicro. Pitts Special for the RFFS-100 by Chris O Riley
Micro Pitts Special for the RFFS-100 by Chris O Riley F1 F2 F3 F4 1 2 3 4 All wood 1/32 inch sheet unless otherwise stated. F1 F2 F3 F4 Small balsa blocks for LG reinforcement Small balsa blocks for LG
More informationSUPER SHED. Indoor shelter for your outdoor tools.
SUPER SHED Indoor shelter for your outdoor tools. Not everyone needs a garden shed. But, if you've no more space on your garage wall for that new leaf rake, if you can't find your potting trowel because
More informationPepper Mill Instructions by Fred Kachelhofer
by Fred Kachelhofer I have seen Nick Cook turn a pepper mill twice and read his article posted at http://www.nickcookwoodturner.com/articles.htm (follow link and then click on Pepper Mill ). I have had
More informationOvernight Sensations Speaker Kit
Overnight Sensations Speaker Kit Thank you for purchasing the Overnight Sensation cabinet kit. This speaker kit was precision cut using CNC machinery for the best possible fit and finish. With a little
More informationThreaded-lid. Acorn. project that won t fall far from the lathe
Threaded-lid Acorn A The fun Woodturner s project that won t fall far from the lathe By Nick Cook Above: Rich texturing to a 53 4" x 31 2" acorn box enhances the appeal of the Willard Baxter acorn shown
More informationArea of Parallelograms, Triangles, and Trapezoids (pages 314 318)
Area of Parallelograms, Triangles, and Trapezoids (pages 34 38) Any side of a parallelogram or triangle can be used as a base. The altitude of a parallelogram is a line segment perpendicular to the base
More informationAZEK Rail Install Guide
TRIM MOULDING DECK PORCH RAIL PAVERS AZEK Rail Install Guide Installing AZEK Rail with Glass Infill... 2 Installing AZEk Rail Stairs with Glass Infill... 9 Notes...14 Please read all instructions completely
More informationDuPont Surfaces DUPONT TM CORIAN SOLID SURFACE 12mm GAUGE STANDARDIZATION
DuPont Surfaces DUPONT TM CORIAN SOLID SURFACE PRODUCT ADVISORY TABLE OF CONTENTS PAGE SECTION 1 A. Introduction 2 B. Bull-nose edge treatment 3 C. Ogee edge treatment on stacked edges 4 D. Coved Backsplashes
More information3D Print Link's Hylian Shield
3D Print Link's Hylian Shield Created by Ruiz Brothers Last updated on 2015-07-14 04:20:12 PM EDT Guide Contents Guide Contents Overview Parts, Tool & Supplies 3D Printing 3D Printed Parts Slicer Settings
More informationMONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL. Craft Shop Manager Bill Clinton wclinton@montana.
MONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL Craft Shop Manager Bill Clinton wclinton@montana.edu 994 4402 1 Policies and Procedures 1. Eye Protection Eye protection must be
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationHow To Level A Subfloor
Skill Level: INTERMEDIATE Give these projects a try if you're a confident DIYer with a good working knowledge of a variety of tools. They can take a day or more to complete. If you can build a birdhouse
More informationBuilding Pluto Subwoofers with Large PVC Pipe
Building Pluto Subwoofers with Large PVC Pipe I decided to make the Pluto subwoofers from 10-12 diameter PVC pipe. It seemed to me that these would be a better visual match to the Plutos themselves. The
More informationGarage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
More informationThings you need to assemble the tube actuator. Left to right. are small piece of masking tape, super glue,pen knife and small
Things you need to assemble the tube actuator. Left to right are small piece of masking tape, super glue,pen knife and small crosspoint screwdriver. You will also need a few drops of light oil. Begin by
More informationHome Storage Projects
This is an excerpt from the book Home Storage Projects by Paul Anthony Copyright 2001 by The Taunton Press www.taunton.com KITCHEN WORK STATION IN MANY KITCHENS, counter space is at a premium. There just
More informationwith three small holes to supply an indexing head, and is prevented from slipping by means of a piece of spring wire. One feather
OR LEATHER a perfect fifty-four or take your archery with a dash of small game hunting, you will find keen enjoyment in this ancient sport. Making the tackle is simple. Size of tackle: The first thing
More informationFabricating a chassis from clad PCB board material
Fabricating a chassis from clad PCB board material How many times have you started a project and the finished appearance is based on what box you had laying around, rather than what you would like to have?
More informationALPERTON COMMUNITY SCHOOL MATHS FACULTY ACHIEVING GRADE A/A* EXAM PRACTICE BY TOPIC
ALPERTON COMMUNITY SCHOOL MATHS FACULTY ACHIEVING GRADE A/A* EXAM PRACTICE BY TOPIC WEEK Calculator paper Each set of questions is followed by solutions so you can check & mark your own work CONTENTS TOPIC
More informationBuild and Fly the Fokker D- 8
Details are carefully carried out. Note movable controls The high wing gives it unusual stability Build and Fly the Fokker D- 8 Complete Data From Which You Can Build a Successful Model of a Famous German
More informationLine Segments, Rays, and Lines
HOME LINK Line Segments, Rays, and Lines Family Note Help your child match each name below with the correct drawing of a line, ray, or line segment. Then observe as your child uses a straightedge to draw
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. GeneralShale.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide GeneralShale.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationVacuum chucking. MDAE Woodturning Center Course Number 95537001
Purpose of vacuum chucking Vacuum chucking MDAE Woodturning Center Course Number 95537001 Completing the foot of a vessel Re chucking a completed object Quick securing for additional steps (sanding) How
More informationBUILDINGA 1/10 SCALE FLATBED TRAILER
VOLUME 1, ISSUE 1 BUILDINGA 1/10 SCALE FLATBED TRAILER BUILT, DESIGNED & WRITTEN BY NATHAN MYERS MATERIALS: FEATURES: While the design was kept simple to allow anyone to be able to build their own trailer,
More informationMaking Clock Wheel & Pinion Cutters
Making Clock Wheel & Pinion Cutters When making hand made clocks or in repair work an odd size cutter is sometimes needed. Sometimes just one pinion is required and does not justify the cost of a commercial
More informationEucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in handling.
i This instruction sheet describes the proper methods for installing Eucatex decorative wall paneling. Eucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in
More informationA Simple Approach to Raised-Panel
A Simple Approach to Raised-Panel 82 FINE HOMEBUILDING Wainscot BY GARY STRIEGLER Stock molding and MDF panels transform a room 1 2 3 4 3 5 6 Raised-panel wainscot speaks of a time when craftsmen had an
More informationBLADE REPAIR INSTRUCTION BOOKLET
BLADE REPAIR INSTRUCTION BOOKLET Contents Section I: Section II: Section III: Section IV: Section V: Section VI: Removing a Blade Refer to this section if you need to remove the blade from an oar shaft.
More informationBUILD A CARPORT. 2 - Planning the carport. 3 - Designing the carport
BUILD A CARPORT You only need basic DIY and woodworking skills to build a carport. The most important part of the job is setting the supporting posts truly vertical - a job for which another pair of hands
More informationOriginal Recipe. Clermont Farms Quilted Tote Bag by Glenn Dragone
Original Recipe Clermont Farms Quilted Tote Bag by Glenn Dragone This Americana themed, multipurpose tote is suitable for the pool, the green market, or a fun day trip. 1 Clermont Farms Jelly Roll by Minick
More informationMaking Laminated Rolling Pins
Making Laminated Rolling Pins Introduction Why go to the trouble to make a rolling pin when you can go down to your local discount store and buy one that works just fine for less than $5? As wood turners,
More informationDave s Sheet Metal Bending Brake
Dave s Sheet Metal Bending Brake I started building a Zenith CH601XL from plans in mid January 2006. After several failed attempts to bend the rudder spar I ended up going to a local sheet metal shop for
More informationBalance Beam Plans. Copyright 2007 Ben MacLeod Email: sales@betterplans.net Website: www.betterplans.net
Balance Beam Plans Copyright 2007 Ben MacLeod Email: sales@betterplans.net Website: www.betterplans.net Balance Beam Plans By Ben MacLeod Copyright 2007 Tools required: -Mitre saw, circular saw, jig saw,
More informationA. Title Page. B. Project Proposal And Project Management
A. Title Page B. Project Proposal And Project Management i. Project Proposal - Identification Of Needs - Areas Of Investigation - Criteria To Evaluate Success ii. Action Plans iii. Time Plans iv. Finance
More informationDRAWING INSTRUMENTS AND THEIR USES
Chapter - A DRAWING INSTRUMENTS AND THEIR USES Drawing Instruments are used to prepare neat and accurate Drawings. To a greater extent, the accuracy of the Drawings depend on the quality of instruments
More informationREDWOOD. Adirondack Chair. Naturally beautiful Easy to use Practical and economical Durable and stable Resistant to decay and insects
B U I L D I T W I T H REDWOOD Adirondack Chair R E D W O O D Naturally beautiful Easy to use Practical and economical Durable and stable Resistant to decay and insects Adirondack Chair BUILD THE CHAIR
More information