Balance Beam Plans. Copyright 2007 Ben MacLeod Website:
|
|
- George Golden
- 7 years ago
- Views:
Transcription
1 Balance Beam Plans Copyright 2007 Ben MacLeod Website:
2 Balance Beam Plans By Ben MacLeod Copyright 2007 Tools required: -Mitre saw, circular saw, jig saw, or hand saw -drill -tape measure -hammer -80 grit sandpaper or power sander -pencil -1 1/8 drill bit (spade type is cheapest if you are planning to buy this) -3/8 dill bit -square -9/16 socket and ratchet Materials required: -1 piece 4 x4 x16-6 pieces 3/8 x 6 galvanized lag bolts -6 pieces 3/8 galvanized flat washers -finish A couple of notes before we begin: -If you have any questions, concerns or comments please sales@betterplans.net -You will receive a response generally within a few hours. -Please consider reading the directions completely before beginning. I think you ll find if helpful to have a general idea of the whole project before you start. -The legal stuff: This balance beam has been designed to conform to Canadian and American consumer safety guidelines. Every effort has been made to ensure that this balance beam is as safe as possible, however many factors can influence the overall safety of this structure such as, but not limited to; weather, decay, rusting fasteners, improper assembly or poor wood choice. Therefore, I will assume absolutely no responsibility, legal or otherwise for any injury which may occur
3 before or during assembly or at any time during the useful life of this balance beam. By proceeding with these plans, you agree to this legal disclaimer. Thanks for understanding. Shall we get started? STEP 1: Decide on wood and finish. The first thing you need to do is make a couple of decisions. 1) What kind of wood are you going to use? While hardwoods such as cedar or redwood are excellent choices due to their nice color and grain and their superior resistance to decay, they are also very expensive. Softwoods, such as pine, fir and spruce (my personal choice) aren t quite as fancy but much less costly and with a good coat of stain or water repellent, they will hold up well for many years. Pressure treated lumber is very cost effective and very durable but I personally use caution with this wood in a child s play structure due to the harsh chemicals used in the treating process. How this affects kids, if at all, is a hotly debated issue and therefore its use is at your own discretion. 2) What kind of finish will you be applying? Even hardwood should have a water repellent sealer of some kind applied. I personally recommend a good quality outdoor stain. You can pick the color of your choice and a simple recoat every few years will ensure your balance beam remains free of decay. STEP 2: Acquire the tools required. The second step is to make sure you have all the tools required. This list is provided at the beginning of the plans. There are a couple of things to keep in mind while acquiring these items. A power mitre saw, circular saw or jig saw are the easiest but with a little more work, all the cuts can be made by hand. Also consider borrowing the larger and more expensive tools if you don t use them a lot. A power sander is fastest for the sanding but again, with a little more work, all the sanding can be done by hand.
4 STEP 3: Acquire the building materials. Acquiring the building materials can be as simple as taking my list to the building supply section of your local building supply store and letting the staff gather the items for you. I recommend picking the lumber out yourself which ensures you will be getting the quality you desire. Or you can gather everything yourself, either way, if you have everything on the list, that s all you need. STEP 4: Preparing the supports Cut three pieces of 4x4; 24 inches long and mitre the top corners about 1 ½ inches from the ends as shown in photo 01. PHOTO 01 On the bottom of each piece, measure and mark the locations as shown in photo 02. First drill 1 1/8 inch holes about ½ inch deep. These will be the recesses for the bolt heads. In the centre of these holes drill a 3/8 inch hole all the way through.
5 PHOTO 02 Round off the sharp corners and edges as shown in photo 03. This looks nice and minimizes bumps and bruises. PHOTO 03 These are your beam supports and you should have three identical ones. Set them aside and go to step 5.
6 STEP 5: Prepare the main beam You should have a piece of 4x4 left roughly 10 feet long. Sand the ends, corners and edges as shown in photo 04. PHOTO 04 STEP 6: Assemble the balance beam. Align one of the supports on your beam as shown in photo 05. PHOTO 05
7 Keep your square handy and install one washer and lag bolt as shown in photo 06. You may need to give it a tap with the hammer to get it started into the beam. Tighten it down with the 9/16 socket and ratchet. Minor adjustments as you go may be required to keep everything square. Install the second lag bolt the same way. PHOTO 06 Repeat this procedure for a second support on the other end of the beam. Then install the third support centering it directly between these two and your balance beam should now look like photo 07.
8 PHOTO 07 STEP 7: Prepare for the finish. Check your entire balance beam again for any imperfections, sharp corners, splinter hazards, or lumber stamps. Finish up any sanding and generally prepare for the finish. STEP 8: Finishing your Balance Beam The finish is basically up to you. I recommend water based stains or clear coats simply because they clean up easily and they are safer for kids. Follow the directions on the can for application. Photo 08 shows Fire Coals on the supports and Happiness Yellow on the beam.
9 PHOTO 08 STEP 9: Enjoy your balance beam and the satisfaction of watching your child(ren) at play. Don t forget to periodically check the lag bolts for tightness. Visit for more great plans!
How to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationEasy Six Cube Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 6 Cube Bookshelf Skill Level: Beginner Easy Six Cube Bookshelf I love the storage cubes in kids rooms because they give you an opportunity to have your children
More informationINSTALLATION INSTRUCTIONS
Turbo Tube Slide INSTALLATION INSTRUCTIONS C A U T I O N Do not climb on the outside of the slide This slide is designed for home use only, not for Public Playgrounds PlayCore, Inc. 2004 Copyrighted Material.
More informationPicnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
More informationAssembly Instructions Basic Folding-Leg Box Frame Style
Assembly Instructions Basic Folding-Leg Box Frame Style Basic Folding Leg Cornhole Board Concept 1 2 12 3 1 2 3 15 16 4 1 4 52 9 R1 3 4 6 21 48 12 1 4 Bolt Washer 9 13 16 35 Washer Double Nut CornholePlayers.net
More informationHow to Build an Elevated Square Foot Garden
How to Build an Elevated Square Foot Garden Thralls, Edmund L., Extension Faculty, Urban Horticulture Fact Sheet Horticulture - 010 Tools: The Institute of Food and Agricultural Sciences (IFAS) is an Equal
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationREDWOOD. Adirondack Chair. Naturally beautiful Easy to use Practical and economical Durable and stable Resistant to decay and insects
B U I L D I T W I T H REDWOOD Adirondack Chair R E D W O O D Naturally beautiful Easy to use Practical and economical Durable and stable Resistant to decay and insects Adirondack Chair BUILD THE CHAIR
More informationDECKING INSTALLATION, CARE & MAINTENANCE INSTRUCTIONS. 866.729.2378 MOISTURESHIELD.COM limited lifetime warranty 866.729.2378 WWW.MOISTURESHIELD.
DECKING INSTALLATION, CARE & MAINTENANCE INSTRUCTIONS 866.729.2378 MOISTURESHIELD.COM limited lifetime warranty Welcome To The Even Greater Outdoors. Congratulations on choosing MoistureShield for your
More informationFrequently Asked Questions and Common Mistakes to avoid when buying a pergola
Frequently Asked Questions and Common Mistakes to avoid when buying a pergola Pergolas are significant investments that add value and enjoyment to open spaces of all sizes and shapes. The choices are almost
More informationHow to Build a Strawberry Pyramid Watch the how-to video here.
How to Build a Strawberry Pyramid Watch the how-to video here. This simple, elegant strawberry pyramid can be built by a single person in just one afternoon. Cut the lumber yourself if you have some woodworking
More informationLadder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationSTEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13
STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More information1998-2002 Suzuki Katana Fender Eliminator
1998-2002 Suzuki Katana Fender Eliminator The following are instructions and illustrations on the installation of the custom fender elimination. 1 Begin by removing seat, both rear fairings, and tail light
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationCable Support System Guide for Andersen Bow, Bay, and Box Projecting Window Units
for Andersen Bow, Bay, and Box Projecting Window Units Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationMODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER
MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.
More informationWood Projects Outdoors. Post Hole Specifications. Deck Span Tables. www.jon Eakes.com
Wood Projects Outdoors Post Hole Specifications & Deck Span Tables www.jon Eakes.com Building Fences The depth of the fence posts into the ground must be at least one foot below the frost level for your
More informationA Telescoping Hive Cover
A Telescoping Hive Cover The telescoping hive cover is what keeps the weather and elements out of your bee hive; it is like the roof of your house (Figure 1). Commercial hive covers typically feature a
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationDave s Sheet Metal Bending Brake
Dave s Sheet Metal Bending Brake I started building a Zenith CH601XL from plans in mid January 2006. After several failed attempts to bend the rudder spar I ended up going to a local sheet metal shop for
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationAssembly and Usage Instructions
Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free
More informationRECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair
RECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair As early as the eighth century B.C., the Greeks used a piece of furniture called the kline, for lounging
More informationHive Top Ventilation Shims
Hive Top Ventilation Shims When preparing your bee hives for the winter, it is very important to provide for ventilation at the top of the hive. Through out the winter, the bees are expelling a lot of
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationHow To Level A Subfloor
Skill Level: INTERMEDIATE Give these projects a try if you're a confident DIYer with a good working knowledge of a variety of tools. They can take a day or more to complete. If you can build a birdhouse
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationAMERICAN GOTHIC PLAYHOUSE
AMERICAN GOTHIC PLAYHOUSE Project Plan #856 Sheet 1 of 5 Pick a spot and get started with the beautiful that your kids will love. The design of the playhouse includes 35 square feet of interior space plus
More informationBlack Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Black Wolf TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905710-000 SEPTEMBER 2010 NOTE: Please use the instructions in this
More informationHow To Launch A Rocket From A Formica
Building the Basic Bottle Rocket Launch Pad Materials: -Formica double-sink countertop cutout. This can be easily and cheaply obtained from a local company that manufactures and/or installs countertops.
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationPanel/Hand Saw Kit Assembly Instructions
Panel/Hand Saw Kit Assembly Instructions PLEASE READ THE FOLLOWING INSTRUCTIONS BEFORE BEGINNING Brief Summary You will be performing the following Tasks: 1. Determining the degree of shaping laying out
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More information3. Choose between an easy table (24 inches wide) and a hard table (20 inches wide).
Ultra Carpetball Plans Version 2.0 The Best (And Only) Free Carpetball Plans On The Web By Matthew Campbell Instructions: 1. Read these instructions all the way through and look at all the diagrams before
More informationAwanaGames Circle. Official. Diagram 1. Key to diagram: Pin & Striped Bean Bag C Diagonal or Starting Line. B Scoring Pins, or Center.
Official AwanaGames Circle Diagram 1 The AwanaGames Circle is 30 feet in diameter surrounded by a 37-40 foot square. Each team is designated by a color and occupies a quarter-circle or one side of that
More informationActive and Passive Sash Replacement
for Andersen Gliding Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete the procedure, call Andersen at 1-888-888-7020 for
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationSECTION 02845 GUARDRAILS
SECTION 02845 GUARDRAILS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals necessary and repair, replace or install all types of guardrails as specified herein
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationRudder Repair and refinish
Rudder Repair and refinish Montgomery 23 Dauntless The before photograph A receipt found inside the boat showed a previous owner had enlisted a boat yard to perform maintenance on the rudder by shortening
More informationDigital TV Coat Hanger Antenna
Rabbit ears are for rabbits, not digital televisions. In this project, we ll show you how to build your own digital TV antenna from wire hangers, a piece of wood and some pipe. Television antennas are
More informationPOD Visor Instructions
POD Visor Instructions Please read fully before beginning assembly and mounting the Visor Parts List - Visor Left Part (LV), Visor Right Part (RV) Qty 2, Aluminum Crossbars Hardware - Qty 17, 1/4" X 3/4"
More informationrack Star 74 cottagelife.com
rack Star 74 cottagelife.com Give your canoes and kayaks some VIP treatment. Get them off the dock and into a custom storage stand By Wayne Lennox Photography Laura Arsiè A couple of rickety old sawhorses.
More informationTrundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds)
Bunk Beds Unlimited Trundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds) On the following pages we have included all of the necessary drawings and requirements for a Modified twin-size
More informationINSTRUCTION BOOK FOR. Lace And Grommet Theater-Type Screens
INSTRUCTION BOOK FOR Lace And Grommet Theater-Type Screens Pre-Installation Da-Lite Lace and Grommet screens are custom made to meet the requirements for large surface installation of a relatively permanent
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationPolicy on Water Heater Installations Policy No. UPC 510-1-94 Effective: September 1, 1995 Revised: February 10, 1996
CITY OF SAN JOSE BUILDING DIVISION POLICY Policy on Water Heater Installations Policy No. UPC 510-1-94 Effective: September 1, 1995 Revised: February 10, 1996 All new and replacement water heaters installed
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationProtecting Your Home from Wind Damage
Protecting Your Home from Wind Damage During severe thunderstorms or hurricanes, homes may be damaged or destroyed by high winds. Debris flying through the air can break windows and doors, allowing high
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationSHELVES. www.tedswoodworking.com
SHELVES It's rare that bookshelves look as interesting as the objects you display on them. After all, how much can you decorate the edges of your shelves and sides? This unit is unusual because the shelves
More informationSynergy Wood Products, Inc.
Grading of Lumber Even though each type of wood has its own grading system, the purpose of grading lumber is the same; a method to communicate between buyer and seller of what is and isn't acceptable.
More informationAccessible Raised Beds
Community Food and Garden Network Accessible Raised Beds Raised beds at Troy Gardens in Madison, WI. The greatest advantage of raised bed gardening is that it requires much less bending for planting and
More informationMaking Laminated Rolling Pins
Making Laminated Rolling Pins Introduction Why go to the trouble to make a rolling pin when you can go down to your local discount store and buy one that works just fine for less than $5? As wood turners,
More informationBUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationAssembly Instructions ShadeTree Canopy Systems. A wood support constructed with a ShadeTree Bracket System. Garden Getaway
Assembly Instructions ShadeTree Canopy Systems A wood support constructed with a ShadeTree System. Garden Getaway Dear Customer: Thank you for purchasing our ShadeTree Canopy System. We trust these assembly
More informationResponsibilities of a Volunteer Leader
Responsibilities of a Volunteer Leader Inspecting tools for safe conditions. Removing unsafe tools from use and immediately notifying site supervisor. Teaching safe tool use to volunteers on your crew.
More informationTraining Zone: Instruction Manual
Training Zone: Instruction Manual More questions? Our Customer Service team is available to answer your questions Monday - Friday from 9:00 M to 5:00 PM PT. E-mail customerservice@trxtraining.com Call
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationBuild a Trade-Show Booth for Under $200!
Build a Trade-Show Booth for Under $200! This corner booth, with a seven foot front and sweeping 4x8 backdrop, assembles in less than 20 minutes and can be built in one weekend. Materials Tools 4 x8 x3/4
More informationPANEL CONCEPTS LLLP.
The Small Cottage Company DO-IT-YOURSELF CABINS & COTTAGES PANEL CONCEPTS INC. PANEL CONCEPTS LLLP. 2826 Gold 331 Creek N. M-33, Road Mio, Gold Michigan Creek, Montana 4864759733 (989) 826-6511 (406) 288-8585
More informationGeneral Instructions and Guidelines
General Instructions and Guidelines Building Design and Construction To ensure adequate performance and longevity, protect metal panels from potentially corrosive situations and materials. When treated
More informationRockSolid Deck Restoration Application
RockSolid Deck Restoration Application Read all instructions carefully before starting installation. For further details, application techniques and possible installation updates see our website at www.rocksolidfloors.com/support.
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationBuild a Precision. Crosscutting Sled
Build a Precision Crosscutting Sled On-the-money, splinter-free crosscuts are well within your grasp using most well-made tablesaws, but you do have to do a few things to ensure great results cut after
More informationAssembly Instructions
Assembly Instructions Overhead Storage Rack 4 x 8 3 x 8 2 x 8 4 x 6 3 x 6 2 x 6 4 x 4 Two 4x8 Racks Pictured Eagle Industrial Group, Inc. 25471 Arctic Ocean Drive Lake Forest, CA 92630 877.655.3443 888.313.9228
More information*** MAIN VERSION OF BOM ***
*** MAIN VERSION OF BOM *** This is the main parts list for the 2013-2014 FTC game. The parts are listed in different categories (such as "Field Elements, "Hardware," "Wood," etc.). The item numbers assigned
More informationGarage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
More informationPATHWAY Classic Series with Handrails Portable Wheelchair Ramp INSTRUCTIONS FOR USE 6428 REV A 05-21-09
PATHWAY Classic Series with Handrails Portable Wheelchair Ramp INSTRUCTIONS FOR USE. INSTRUCTIONS 1) FOR EZ-ACCESS PATHWAY RAMP WITH HANDRAILS 850 pound weight capacity. Available in 4, 6, 8 & 10 lengths.
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationProtecting Your Home From Hurricane Wind Damage
T H E W I N D Protecting Your Home From Hurricane Wind Damage During a hurricane, homes may be damaged or destroyed by high winds and high waves. Debris can break windows and doors, allowing high winds
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationBuilding Pluto Subwoofers with Large PVC Pipe
Building Pluto Subwoofers with Large PVC Pipe I decided to make the Pluto subwoofers from 10-12 diameter PVC pipe. It seemed to me that these would be a better visual match to the Plutos themselves. The
More informationStandard Operating Procedures 4ft Muscle Wall
Standard Operating Procedures 4ft Muscle Wall Secondary Containment Standard Operating Procedures Page 2 of 12 Table of Contents Page 4 Page 3 Page 7 Page 5 Page 10 Page 11 Page 9 Specifications Items
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationDINING OUT. Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson
DINING OUT Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson http://popularmechanics.com/home_improvement/furniture/2001/4/table_and_bench_set/print.phtml
More informationSPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS
SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS README FIRST: Thank you for purchasing your MyDIYCNC Desktop CNC Machine Kit. We hope this versatile and innovative machine brings you many
More information2. This is a close up of a typical area where the rocker is rusted out leaving holes under where the rocker moulding would be..
ROCKER PANELS 55,56,57 CHEVY REPLACEMENT Do not throw away any pieces when you first remove them. There are many supports that are not reproduced and will need to be used again. When disassembling try
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationReachout Lock Replacement for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors
for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors Thank you for choosing Andersen. For questions call 1-888-888-7020. For more information
More informationMEDIUM FLAT PANEL DISPLAY STATIC MOUNT MSR Series
INSTALLATION INSTRUCTIONS MEDIUM FLAT PANEL DISPLAY STATIC MOUNT The static mount accommodates medium flat panel displays weighing up to 125 lbs (57 kgs). The teardrop holes in the mount allow for quick
More informationSTAIR TREAD & RISER INSTALLATION GUIDELINES
STAIR TREAD & RISER INSTALLATION GUIDELINES ARTISTIC FINISHES DOES NOT WARRANTY THE COMPLETENESS OR ACCURACY OF ANY INSTALLATION. THE INSTALLATION CONTRACTER MUST HAVE THE EXPERIENCE AND KNOWLEDGE TO COMPLETE
More informationIF YOU NEED A POLE BARN OR DIY KIT CALL NOW AND LETS MAKE A DEAL
IF YOU NEED A POLE BARN OR DIY KIT CALL NOW AND LETS MAKE A DEAL Check out our Affordable Selection of DIY Pole Barn kit sizes and prices below. We offer a complete DIY pole barn kit plus independent experienced
More information