March Lincoln Clay pantiles

Transcription

1 CI/SfB March 2016 (47) Ng2 Lincoln Clay pantiles

2 s Lincoln combines the bold and beautiful curves of traditional clay pantiles with all the installation simplicity and speed required for today s roofs. This means that Lincoln affords the rich appeal of natural, clay pantiled roofs, a thin leading edge and a beauty that matures over time. As well as quick and easy installation, Lincoln can be installed to meet the latest fixing requirements of BS 5534 and the NHBC technical standards, without compromising tradition. Lincoln pantiles are available with a comprehensive range of clay fittings and accessories to give a traditional finish. Additionally, many of these components can be combined with our Universal range of accessories and fittings to offer a complete dry fix and maintenance-free solution. All factories certified to ISO 9001, ISO s For advice, literature and samples Tel or visit marleyeternit.co.uk 3

3 Lincoln Rustic Red Semi-sanded finish Lincoln Natural Red Smooth finish 4 s For advice, literature and samples Tel or visit marleyeternit.co.uk 5

4 Tile features and technical data Lincoln key features > traditional profile > easy to install (open-gauge design) > low minimum pitch 17.5 > BS 5534 compatible Key A Raised and protected blind nail hole 370 E A B 247 D Key K L M N SoloFix clip pocket for a flush fit Batten locator to avoid rocking Deep nibs for ease of setting out and fixing Double anti-capillary bars to prevent water ingress L M B C D E F G H Raised and protected head and side locks SoloFix clip recess Extended weather bars over the roll for low pitch protection Wide channel for water run-off Raised ridge to guard against wind-driven rain Open-gauge design for a flexible fit Traditional s-curve profile C F H G Technical data Size of tile 370 x 247mm Minimum pitch* 17.5 (120mm headlap) 22.5 (75mm headlap) Maximum pitch 70 Minimum headlap 75mm Maximum gauge 295mm Cover width 222mm (nominal) Covering capacity 15.3 tiles/m 2 at 75mm headlap (net) 18.0 tiles/m 2 at 120mm headlap Weight of tiling 43.0 kg/m 2 at 75mm headlap (approx.) 50.4 kg/m 2 at 120mm headlap Battens required 3.4 lin.m/m 2 at 75mm headlap (net) (net) 4.0 lin.m/m 2 at 120mm headlap (net) K N I J Thin leading edge Hidden/cloaked interlock I J Batten size 38 x 25mm for rafters/supports recommended not exceeding 450mm centres (fixed to BS 5534) 50 x 25mm for rafters/supports not exceeding 600mm centres Tile nails 38 x 3.35mm Fixing clips Eaves, verge and tile clips Authority BS EN 1304 * The minimum recommended pitch and lap may be influenced by special circumstances, please contact the Technical Advisory Service. The features a completely open-gauge design, making it quick and easy to install. For full technical data and advice, please contact our Technical Advisory Service on s For advice, literature and samples Tel or visit marleyeternit.co.uk 7

5 Lincoln clay fittings and accessories Dry fix ventilation and accessories The following products and accessories can be used with Lincoln clay fittings. Our website also contains further information about dry fix and ventilation solutions: Note: Minimum and maximum pitches may vary please contact our Technical Advisory Service for more information Half round ridge tile Half round ridge end tile 385 Universal eaves vent system Universal 10mm eaves vent system (6m) Universal 25mm eaves vent system (6m) Comb filler strip Continuous rafter roll (2 x 6 m) Gutter spacers (20 per pack) Universal RidgeFast system Universal RidgeFast system (6m) RidgeFast blanking tape (2 x 2 m) RidgeFast/HipFast union pack (6 No. unions) Universal HipFast system Universal HipFast system (6m) Universal HipFast support tray (6m) RidgeFast/HipFast union pack (6 No. unions) Third round hip tile Third round hip end tile Universal GRP dry valley Top abutment ventilation system High profile GRP valley trough (3m) Accommodates up to 20 pitch difference either side of valley Suitable on rafter pitches from 17.5 to 60 Lead support strip (1.5m) Dry ridge batten section (3m) Dry ridge batten section (3m) Lincoln filler unit vented Security fixing Mortar bedded security ridge and hip fixing kits are available to meet the latest British Standards and NHBC guidelines. Left hand verge tile 247 Ventilation tile 247 Note: Minimum and maximum pitches may vary please contact our Technical Advisory Service for more information. Mortar bedded security ridge Mortar bedded security hip Mortar bedded security ridge kit Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityridge or scan the QR code shown Mortar bedded security hip kit Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityhip or scan the QR code shown Dentil slip 8 s All dimensions in mm. For advice, literature and samples Tel or visit marleyeternit.co.uk 9

6 Lincoln Design detailing Bedded verges > ensure undercloak does not tilt towards gable > verge overhang should be a maximum of 50mm > use Lincoln left hand verge tile for left hand verges > mechanically fix all verge tiles in accordance with BS 5534 Universal eaves ventilation > eaves ventilation to satisfy 10mm or 25mm conditions > eaves to ridge ventilation for pitches of > continuous rafter roll compresses insulation to allow free air passage (use two rolls to compress deep insulation) > strip ventilator has discreet ventilation grille and is nailed to fascia or timber fillet Lincoln left hand verge tile Lincoln verge clip Mortar bedding Fibre cement undercloak Tiling batten Tiling batten Lincoln verge clip Mortar bedding Fibre cement undercloak > suitable with or without soffit board > use comb filler strip with deep profiled tiles > mechanically fix all tiles at eaves Continuous rafter roll (2 No.) Tiling fillet Universal HipFast system > provides additional ventilation to the roof void when a 5mm gap in the underlay is used in conjunction with either eaves or ridge ventilated systems or ventilation tiles > use one or two thicknesses of 50mm x 25mm batten to fit batten brackets > use hip end hip tile at eaves Mortar bedded hips > maximum rafter pitch 45 > fix hip units to hip tree using ridge clamp and 100mm stainless steel screw > complete hip at ridge apex with three way mitre > mechanically fix each hip tile via hip unions and clamps > complete hip at ridge with soaker flashing 10/25mm over fascia strip ventilator Ridge union clamp Third round hip tile Ridge union Maximum gauge 295mm Ridge roll flashing Ridge batten bracket Hip batten brackets For more information on security hip fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityhip 10 s For advice, literature and samples Tel or visit marleyeternit.co.uk 11

7 Design detailing Ridge union clamp Half round ridge tile Ridge union Ridge roll flashing Ridge batten bracket Universal GRP dry valley > minimum rafter pitch 17.5, maximum 60 > maximum valley length 8m > suitable for all plan angles and where the pitch either side of the valley varies by a maximum of 20 > provide continuous support for valley trough using 19mm timber ply boards inset between rafters or 6mm continuous ply boards laid over rafters > tightly butt tiles or slates to central upstand of valley units to prevent ingress of birds or vermin > provide metal apron at foot of valley and dress into gutter at eaves. For rafter pitches below 25 cut fascia board to maintain valley pitch Battens at max 295mm gauge Tiling batten High profile dry valley trough 19mm (min) timber valley board s cut to angle of valley Rafter Universal RidgeFast system > provides 5,000mm 2/ m free vent area at ridge apex > ensure gap is provided in roof underlay to vent roof void > use one or two thicknesses of 50mm x 25mm batten to fit batten brackets > mechanically fix all top course tiles > use ridge end tile cut to provide insulation > nail or clip adjacent tiles to the valley > complete top of valley with a lead saddle Mortar bedded ridges > security ridge fixing kits are available for Lincoln clay ridges > maximum rafter pitch 50 > fix ridge units to ridge batten using ridge clamp and 100mm stainless steel screw > mechanically fixes ridge tile in line with BS 5534 fixing guidelines For more information on security ridge fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityridge 12 s For advice, literature and samples Tel or visit marleyeternit.co.uk 13

8 Design detailing Resources Abutment > maximum rafter pitch 45 (55 using steep pitch batten section) > provides 5,000mm 2 /lin.m ventilation > ensure air passage from roof void is not obstructed > mechanically fix all top course tiles > use minimum 1.5m length of lead flashing with 150mm side laps Code 4 lead Lead support strip Dry ridge batten section Lincoln ventilated filler unit cut back 5mm min. to provide ventilation Min. 75mm Technical advice Our Technical Advisory Service is staffed by a qualified team with specialist knowledge. Call or info@marleyeternit.co.uk Fixing instructions and literature Comprehensive sitework, fixing and installation literature and videos: marleyeternit.co.uk/resources All current product and technical literature can be downloaded: marleyeternit.co.uk/downloads Sales support Our Area Sales Managers have in-depth knowledge of your local area. They are available to visit your site to carry out a roof survey, and to offer specific solutions for both new build and refurbishment projects. marleyeternit.co.uk/localcontacts Tilefix To request a fixing specification based on the geographical location and building dimensions of specific building projects. Call or info@marleyeternit.co.uk Batten Samples Samples of clay interlocking and plain tiles, fibre cement slates and concrete tiles are available on request. Tel marleyeternit.co.uk/samples Estimator To request a complete bill of materials for your roofing project: Call or info@marleyeternit.co.uk Lincoln clay tile vent 50mm air gap maintained over insulation Battens at max. 295mm gauge Nailed fixing to back of batten V cut in felt with flap nailed to batten Lincoln clay tile vent > locate clear of rafters > use spigot-soaker tray to weather the offset hole in underlay > locate at m centres for 5,000mm 2 /lin.m ventilation and mm centres for 10,000mm 2 /lin.m ventilation Stockist information To find details for stockists of Marley Eternit products, visit: marleyeternit.co.uk/stockists Customer services Knowledgeable and friendly staff are available to offer quotations, expert advice, deal with orders and all other enquiries. Call or info@marleyeternit.co.uk Training centre We have a purpose-built training centre where we are able to impart our expertise through a range of practical and classroom courses. To find out more about our courses, visit: marleyeternit.co.uk/training Health and Safety In line with the requirements of the Health and Safety at Work Act, The Consumer Protection Act and The Chemicals (Hazard Information and Packaging for Supply) Regulations and the Control of Substances Hazardous to Health Regulations, please download and view copies of our COSHH data sheets at marleyeternit.co.uk/coshh 14 s For advice, literature and samples Tel or visit marleyeternit.co.uk 15

9 Call Or visit Marley Eternit Lichfield Road Branston Burton upon Trent DE14 3HD