ASSEMBLY MANUAL KEEP THIS MANUAL FOR FUTURE REFERENCE IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

Transcription

1 A Backyard Products Company ASSEMBLY MANUAL ASTON 10' x 7'-6" (304,8 x 8,6 cm) ACTUAL FLOOR SIZE IS 10" x 90" (304,8 x 8,6 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE /1/01 IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO NING ASSEMBLY. BEFORE YOU BUILDING RESTRICTIONS AND APPROVALS Be sure to check with local building department and homeowners association for specific restrictions and/ or requirements before building. ENGINEERED DRAWINGS Contact our Customer Service Team if engineered drawings are needed to pull local permits. SURFACE PREPARATION To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are listed on page 7. CHECK ALL PARTS Inventory all parts listed on pages 4-6. Contact our Customer Service Team if any parts are missing or damaged. ADDITIONAL MATERIALS You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities. - CUSTOMER SERVICE - Call: customerservice@backyardproductsllc.com

2 TOOLS Phillips Screwdriver Drill / Driver 1/4" Drill Bit 3/8" Drill Bit 1/" Drill Bit # Philips Drive Bit Hammer Level Pencil Tape Measure Required Utility Knife Shingle Blades Caulk Gun Paint Tools Safety Glasses Ladder Tool Belt/ Nail Pouch Gloves Optional Tin Snips (for drip edge) Chalk Line Nail Gun gun nails Square or Safety! Always use approved safety glasses during assembly. HELPFUL REMINDER SYMBOLS Look for these symbols for helpful reminders throughout this manual. = Assistance Required; two or more people. = Mark part with pencil. = Ensure squareness. = Beginning of steps for assembly or installation. = Important required step or operation. = You have finished the assembly or installation. = Helpful assembly hint. = Level ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side. Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product. (See Fig. A, B, C.) A B C

3 ADDITIONAL MATERIALS This shed kit includes a complete wood floor system. This shed kit does not include ANY leveling materials. FOUNDATION OR FLOOR MATERIALS See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. REINFORCED WOOD FLOOR FRAME (OPTIONAL) IMPORTANT! The included floor has been designed for general use. Depending on your specific use you may want to construct a heavy duty floor frame by adding additional floor joists (shown below). Below is a list of additional materials (not included): x 4 x 87" (5 x 10 x 1 cm) Treated Lumber x8 ea. Hot Dipped Galvanized Nails COMPLETING YOUR SHED You will need these additional materials: Optional 1" (30,1 cm) spacing. Standard spacing is 16" (40,7 cm). 3-TAB SHINGLES... 4 Bundles PAINT FOR SIDING... Gallons Use 100% acrylic latex exterior paint. () coats recommended. CAULK... 3 Tubes Use acrylic latex exterior caulk that is paintable. 1" GALVANIZED ROOFING NAILS... 3 Lbs For shingles. PAINT FOR TRIM...1 Quart Use 100% acrylic latex exterior paint. WOOD GLUE... Exterior Rated TO VALIDATE YOUR WARRANTY YOU MUST USE THE FOLLOWING: DRIP EDGE Feet #15 ROOFING FELT To cover 99 Sq. Ft. of roof area. 1" GALVANIZED ROOFING NAILS...1/4 Lb For roofing felt. REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER S INSTRUCTIONS FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT. 3

4 Part identification letters are stamped on some parts. RS RS Check these locations for part stamp. PARTS IDENTIFICATION AND SIZES Treated lumber is stamped: PARTS LIST INVENTORY YOUR PARTS before you begin. We suggest sorting parts by the category they are listed in. WOOD SIZE CONVERSION CHART Nominal Board Size Actual Size " x 4"...1-1/" x 3-1/" (3,8 x 8,9 cm) 1" x 4"...3/4" x 3-1/" (1,9 x 8,9 cm) " x 3"...1-1/" x -1/" (3,8 x 6,3 cm) 1" x 3"...3/4" x -1/" (3,8 x 6,3 cm) FLOOR x9 x 4 x 48" (5,1 x 10, x 11,9 cm) x 4 x 7" (5,1 x 10, x 18,8 cm) x 4 x 87" (5,1 x 10, x 0,9 cm) All treated lumber is stamped: WALLS RD x4 x 4 x 16-1/" (5,1 x 10, x 41,9 cm) 3/4 (1,9 c x 4 x 8" (5,1 x 10, x 71,1 cm) x 4 x 45-5/8" (5,1 x 10, x 115,8 cm) x 4 x 48" (5,1 x 10, x 11,9 cm) x 4 x 64" (5,1 x 10, x 16,5 cm) x 4 x 68" (5,1 x 10, x 17,7 cm) x 4 x 7" (5,1 x 10, x 91,4 cm) x 4 x 7-5/8" (5,1 x 10, x 184,5 cm) x 4 x 74-1/4" (5,1 x 10, x 188,6 cm) x 4 x 79-1/8" (5,1 x 10, x 01,3 cm) x 4 x 85-1/" (5,1 x 10, x 17, cm) x 4 x 86" (5,1 x 10, x 18,4 cm) RR BMA x3 SP x6 UX UM x3 TM BFA BNA BJA BKA x4 BLA UN x 4 x 94-1/" (5,1 x 10, x 40 cm) GAA 1 x 3 x 5" (,5 x 7,6 x 1,7 cm) RAFTERS x9 BRA BPA HJ x 3 x 10-1/" (5,1 x 7,6 x 6,7 cm) 1 x 3 x 33-1/8" (,5 x 7,6 x 84,1 cm) 1 x 3 x 7" (,5 x 7,6 x 18,8 cm) x9 BOA x 4 x 93-3/16" (1,5 x 10, x 36,7 cm) x4 EY 19/3 x - 1/ x 9" (1,5 x 6,3 x,9 cm) BYA 19/3 x 3-1/ x 35-1/4" (1,5 x 8,8 x 89,5 cm) BQA x 3 x 33-1/8" (5,1 x 7,6 x 84,1 cm) TRIM FS ZT x 3 x 35-1/4" (5,1 x 7,6 x 89,5 cm) 19/3 x 3-1/ x 48" (1,5 x 8,8 x 11,9 cm) BUA 19/3 x 3-1/ x 5-3/8" (1,5 x 8,8 x 133 cm) BXR 19/3 x 3-1/ x 59-1/4" (1,5 x 8,8 x 150,4 cm) BXL 19/3 x 3-1/ x 59-1/4" (1,5 x 8,8 x 150,4 cm) 4

5 OY PARTS LIST continued... x 3 x 7" (5,1 x 7,6 x 18,8 cm) TRIM BTA 19/3 x 3-1/ x 80" (1,5 x 8,8 x 03, cm) BSA 19/3 x -1/ x 91" (1,5 x 6,3 x 31,1 cm) PT x 3 x 96" (5,1 x 7,6 x 43,8 cm) ZX 19/3 x 3-1/ x 96" (1,5 x 8,8 x 43,8 cm) CORNER/FREIZE TRIM 3/8 x x 5-3/8" (0,9 x 5,1 x 64,4 cm) 3/8 x x 68-3/4" (0,9 x 5,1 x 174,6 cm) 3/8 x x 69-1/4" (0,9 x 5,1 x 175,8 cm) 3/8 x x 69-1/4" (0,9 x 5,1 x 175,8 cm) 3/8 x x 91-1/4" (0,9 x 5,1 x 31,7 cm) 3/8 x x 93-1/4" (0,9 x 5,1 x 36,8 cm) 3/8 x x 93-1/4" (0,9 x 5,1 x 36,8 cm) 3/8 x x 96" (0,9 x 5,1 x 43,8 cm) 35-3/4 x 10-3/8 x 3/8" (90,8 x 6,3 x 1 cm) SOFFIT 95-3/8 x 10-3/8 x 3/8" (4, x 6,3 x 1 cm) 95-1/ x 5-1/4 x 3/8" (4,5 x 13,3 x 1 cm) x4 AH 19/3 x -1/ x 6-5/8" (1,5 x 6,3 x 67,6 cm) OO x 3 x 69" (5,1 x 7,6 x 175, cm) Roof panels are 7/16" (1,1 cm) thick. PANEL PARTS LIST Floor panels are 5/8" (1,6 cm) thick. 7/16 x 11-7/8 x 35-7/8" (1,1 x 30, x 91,1 cm) ROOF PANELS 7/16 x 11-7/8 x 96" (1,1 x 30, x 43,8 cm) 7/16 x 35-7/8 x 96" (1,1 x 91,1 x 43,8 cm) 7/16 x 48 x 96" (1,1 x 11,9 x 43,8 cm) FLOOR 5/8 x 3-7/8 x 90" (1,5 x 60,6 x 8,6 cm) 5/8 x 4 x 96" (1,5 x 106,6 x 43,8 cm) 5/8 x 48 x 96" (1,5 x 11,9 x 43,8 cm) NOTE: Panel parts are not stamped. 5

6 WALL PANEL & S PARTS LIST 3/8 x 3-7/8 x 7" (1 x 60,6 x 18,9 cm) 3/8 x 48 x 7" (1 x 113,3 x 11,9 cm) 3/8 x 11-7/8 x 96" (1 x 30,1 x 43,8 cm) 3/8 x 4 x 83-1/8" (1 x 106,6x 11,1 cm) 3/8 x 4 x 83-1/8" (1 x 106,6x 11,1 cm) 3/8 x 48 x 96" (1 x 11,9x 43,8 cm) 3/8 x 48 x 96" (1 x 11,9x 43,8 cm) 3/8 x 48 x 96" (1 x 11,9x 43,8 cm) 3/8 x 48 x 96" (1 x 11,9x 43,8 cm) LEFT RIGHT NAIL BOXES BOXES x3 BOXES " (5,1 cm) FASTENER/HARDWARE BAG x88 x75 1-1/4" (3, cm) " (5,0 cm) x56 3/4" (1,9 cm) /" (3,8 cm) 10 " (5,1 cm) VENT, HARDWARE, AND WINDOW 8 x 16" (0,3 x 35,6 cm) x3 9 X 7" (,8 x 68,5 cm) x8 1" (,5 cm) 1-1/" (3,8 cm) 1/" (1, cm) 6

7 FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS 3" Screws angled into 4x4. () at each point frame and 4x4 touch. 1" (30,5 cm) MATERIAL REQUIRED 4" x 4" x 10' (10 x 10 x 304,8 cm)treated Lumber 1" (30,5 cm) Fasteners for Frame to 4"x 4". (3" Screws shown as one option.) Minimum (40) 3" screws / exterior grade. Measurements to center of 4x4's. Use only wood treated for ground contact and fasteners approved for use with treated wood. Always support frame seams. 1" Maximum between leveling material locations. 48" Shingle Level 4x4 Runner 1" Shingle Gravel " Block Gravel 4" Block LEVELING METHODS x4 Treated Lumber 8" Block Level under 4x4 runners only. Locate leveling material 1" from ends of runners and no more than 48" apart. Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use shingles in direct contact with ground. For best results and aiding in water drainage use gravel under each concrete block. LEVELING MATERIALS Gravel Solid Masonry Blocks in 1", ", 4" or 8" thickness x4 Treated Lumber Asphalt Shingles Leveling higher than 16" not recommended. CONCRETE If you are building your shed on a concrete foundation see the following page. 7 Do not exceed 16".

8 CONCRETE FOUNDATION Your kit contains all materials to construct a wooden floor. If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C B 3-1/" (8,9 cm) 4" (10, cm) A Building Size 10'x 7'-6" (304,8 x 8,6 cm) Requires: " x 4" x 10'-0" (5,1 x 10, x 304,8 cm) " x 4" x 7'-6" (5,1 x 10, x 9,6 cm) Caulk Allow new concrete slabs to cure for at least seven (7) days. A treated x 4" (5,1 x 10, cm) sill plate is required when installing your shed on concrete. Hint: Use treated lumber in your kit or purchase full length treated lumber. Use a high quality exterior grade caulk beneath all sill plates. Fasten x 4" (5,1 x 10, cm) sill plates to slab using approved concrete anchors (fasteners not included). Check local code for concrete foundation requirements. Actual Size A B C 10" x 90" (304,8 x 8,6 cm) 10" (43,9 cm) 83" (10,9 cm) NOTES MUST be treated lumber. MUST be treated lumber. 90" (8,6 cm) 8

9 PARTS REQUIRED: x9 x 4 x 87" (5,1 x 10, x 1 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) x 4 x 48" (5,1 x 10, x 11,9 cm) FLOOR FRAME 1 Orient parts as shown on flat surface. Measure and mark. Use two 3" nails at each mark. x40 Look for TREATED Stamp 3 You have finished your floor frame. Proceed to level and square frame. 1-1/4" (31 cm) 11-5/8" (9,5 cm) 7" (18,9 cm) 16" (40,6 cm) HINT: For easier nailing stand on frame. 10" (304,8 cm) 107-5/8" (73,4 cm) 96" (43,8 cm) 80" (03, cm) 64" (16,6 cm) 48" (11,9 cm) 3" (81,3 cm) 16" (40,6 cm) Note this measurement Center on marks TOENAILING 90" (8,6 cm) 87" (1 cm) 7" (18,9 cm) 48" (11,9 cm) 9

10 LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. 1 See page 7 for the preferred floor leveling method. 3 4 Use level and check the frame is level before applying floor panels. Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square. The diagonal measurement will be approximately 150" (381 cm). When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one fastener at ends of each runner making sure the frame remains square (Fig. A). 5 Once the floor frame is level and square fasten the frame to the 4x4 runners at each point the frame contacts the 4x4 runners. First, secure at ends with one fastener. Fig. A 150" (381 cm) 150" (381 cm) Second, secure at ends with one fastener. 10

11 FLOOR PANELS PARTS REQUIRED: x50 " (5,1 cm) 5/8 x 48 x 96" (1,6 x 11,9 x 43,8 cm) 1 Ensure your floor frame is square by installing one panel and squaring frame. Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with two " nails in the corners. Move to the opposite side. Using the long edge of the panel as a lever, move the panel side-to-side until the top corner is flush to the floor frame (Fig. B). Secure panel with two " nails in the corners. 3 Check the floor frame is square by measuring diagonally across the frame corners. If the measurements are the same your floor frame is square. The measurement will be approximately 150" (381 cm) (Fig. C). 4 Continue attaching the panel using " nails 6" apart on edges and 1" apart inside panel. Use a chalk line or use pre-painted grid lines to nail into joists under panel. Seam 3/4" (1,9 cm) Grid lines up Fig. A () Nails 6" (15, cm) 1" (30,5 cm) 48" (11,9 cm) () Nails 3/4" (1,9 cm) 10" (304,8 cm) Seam Fig. B 150" (381 cm) 150" (381 cm) Fig. C 11

12 PARTS REQUIRED: 5/8 x 4 x 96" (1,6 x 106,7 x 43,8 cm) 5/8 x 3-7/8 x 90" (1,6 x 60,6 x 8,6 cm) FLOOR PANELS x91 " (5,1 cm) Continue installing panels with rough side up (painted grid lines). Use grid lines on panel for " nails 6" apart on edges, and 1" apart inside panels. 7 You have finished attaching your floor panels. 3-7/8" (60,6 cm) 6" (15, cm) 1" (30,5 cm) 4" (106,7 cm) Grid lines up 10" (304,8 cm) 1

13 IMPORTANT! Check the floor frame is level after installing floor panels. Re-level if needed. The floor should be used as a stable work surface for wall construction. HINT: Organize your assembly procedure during the build process to avoid over-handling of the walls. Back wall Front wall 13

14 PARTS REQUIRED: SP x6 UX TM BACK WALL FRAME 8 x 4 x 48" (5,1 x 10, x 11,9 cm) x 4 x 64" (5,1 x 10, x 16,5 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) 1 For back wall, orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark and four 3" nails at seams HINT: For easier nailing stand on frame. 48" (11,9 cm) 10" (304,8 cm) 96" (43,8 cm) 7" (18,9 cm) 48" (11,9 cm) 4" (61 cm) SP 1-1/" (3,8 cm) TM 64" (16,5 cm) 1-1/" (3,8 cm) UX x6 TM 1-1/" (3,8 cm) SP 7" (18,9 cm) 48" (11,9 cm) 14

15 BACK WALL PANELS PARTS REQUIRED: GAA x45 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 3/4" GAUGE BLOCK Ensure your wall frame is square by installing one panel and squaring frame. 3 Place 48 x 7" panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with two " nails in the corners (Fig. A). 4 5 Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have a 3/4" measurement on the wall stud. Secure corner with two " nails (Fig. B). Nail the panel using " nails 6" apart on edges and 1" apart inside panel. Nails 3/4" (1,9 cm) 3/4" (1,9 cm) Nails Fig. A Fig. B 4" (10, cm) 3/4" (1,9 cm) HERE For squareness maintain 3/4" measurement along panel edges. 3/4" GAUGE BLOCK 6" (15, cm) 1" (30,5 cm) Primed side up 48" (11,9 cm) 3/4" (1,9 cm) 15

16 BACK WALL PANELS PARTS REQUIRED: GAA x75 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 3-7/8 x 7" (60,6 x 13,4 cm) 3/4" GAUGE BLOCK For squareness maintain 3/4" measurement along panel edges. 6 Place center 48" x 7" panel on frame as shown with primed side facing up. 4" (10, cm) 3/4" (1,9 cm) Nail using " nails 6" apart on edges and 1" apart inside panel. Primed side up 6" (15, cm) 3/4" GAUGE BLOCK 1" (30,5 cm) 48" (11,9 cm) 3/4" (1,9 cm) 7 Place end 3-7/8" x 7" panel on frame as shown with primed side facing up. Nail using " nails 6" apart on edges and 1" apart inside panel. For squareness maintain flush along panel edges. 4" (10, cm) 6" (15, cm) 8 Carefully flip the BACK wall over. Primed side up 3-7/8" (60,6 cm) 9 You have finished building your back wall. 16

17 PARTS REQUIRED: x4 RD BMA UM BNA BLA UN x 4 x 16-1/" (5,1 x 10, x 4 cm) FRONT WALL FRAME RR x 4 x 45-5/8" (5,1 x 10, x 115,8 cm) x 4 x 68" (5,1 x 10, x 17,7 cm) x34 x 4 x 74-1/4" (5,1 x 10, x 188,6 cm) x 4 x 8" (5,1 x 10, x 71, cm) x 4 x 86" (5,1 x 10, x 18,4 cm) x 4 x 94-1/" (5,1 x 10, x 40,1 cm) 1 For front wall, orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark and four 3" nails at seams. 10" (304,8 cm) HINT: For easier nailing stand on frame. 108" (74,3 cm) 9" (33,7 cm) 45-5/8" (115,8 cm) BMA 74-1/4" (188,6 cm) BNA 8" (7, cm) 1" (30,5 cm) RD 16-1/" (4 cm) UN 74-1/4" (188,6 cm) 86" (18,4 cm) BLA X UM 94-1/" (40,1 cm) UM BLA X 68" (17,7 cm) RR 64" (16,6 cm) RR 1" (30,5 cm) 16" (40,6 cm) 16" (40,6 cm) 1" (30,5 cm) 8" (71, cm) 17 8" (71, cm)

18 PARTS REQUIRED: x3 RD x 4 x 16" (5,1 x 10, x 4 cm) FRONT WALL FRAME 3 4 Orient parts on edge as shown. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. RD RD 7-1/" (69,9 cm) 7-1/" (69,9 cm) 7-1/" (69,9 cm) 64" (16,6 cm) You have finished building your front wall frame. 5 18

19 PARTS REQUIRED: 3/8 x 48 x 96" (1 x 11,9 x 43,8 cm) FRONT WALL PANELS 3/4" GAUGE BLOCK x40 " (5,1 cm) Handle panels with care to avoid breakage. 1 Place 48 x 96" left panel primed side up onto wall frame centered in door opening as shown. Ensure top of panel is overhanging the top of frame by 5-1/". Hold the 3/4" measurement along left edge of panel. Use a gauge block. Nail panel with two " nails 6" (15, cm) apart. Maintain 64" (16,5 cm) measurement between studs and square frame. 5-1/" (14 cm) UNTIL FRONT PANELS ARE INSTALLED, HANDLE CAREFULLY TO AVOID BREAKING AT CORNERS AND EDGES. HERE 3/4" GAUGE BLOCK For squareness maintain 3/4" measurement along panel edge. 3/4" (1,9 cm) Maintain Square CENTER CENTER 6" (15, cm) MAINTAIN 64" DIMENSION BETWEEN STUDS Primed side up 19

20 PARTS REQUIRED: 3/8 x 48 x 96" (1 x 11,9 x 43,8 cm) OO x 3 x 69" (5,1 x 7,6 x 175,3 cm) TEMPORARY SUPPORT FRONT WALL PANELS 3/4" GAUGE BLOCK x40 " (5,1 cm) 3 Place 48 x 96" right panel primed side up onto wall frame flush to left panel. Hold the 3/4" measurement along right edge of panel. Use a gauge block. 4 Nail panel with two " nails 6" (15, cm) apart. Maintain 64" (16,5 cm) measurement between studs and square frame. 5 Use OO as a brace to maintain 64" (16,6 cm) opening. Use two 3" screws to attach. Primed side up 5-1/" (14 cm) 3/4" GAUGE BLOCK For squareness maintain 3/4" measurement along panel edge. Maintain Square 3/4" (1,9 cm) Screw MAINTAIN 64" DIMENSION BETWEEN STUDS Screw 6" (15, cm) Install OO after panels for temporary brace. 0

21 PARTS REQUIRED: 3/8 x 11-7/8 x 96" (1 x 30,5 x 43,8 cm) FRONT WALL PANELS x60 " (5,1 cm) 6 Place 11-7/8 x 96" panel onto wall frame flush to left 48 x 96" panel with primed side up as shown. Ensure top of panel is overhanging the top of frame by 5-1/". 7 Nail the panel using " nails 6" apart on edges. 8 Repeat steps 6 and 7 to attach the right panel. 5-1/" (14 cm) 5-1/" (14 cm) Primed side up Primed side up 6" (15, cm) 6" (15, cm) MAINTAIN 64" DIMENSION BETWEEN STUDS 9 You have finished building your front wall. 10 Carefully flip the FRONT WALL over. 1

22 PARTS REQUIRED: BACK WALL INSTALLATION 0 " (5,1 cm) Stand backwall on floor. It is important to secure the backwall in the following order. ENSURE 4" MEASUREMENT IS AT TOP OF BACK WALL ASSEMBLY. 1 Center back wall assembly on the 10" floor dimension. 4" (10, cm) 10" (304,8 cm) 3 First, nail lower edge of panel to floor frame using " nails 6" apart. Angle nail to hit floor frame (Fig. A). Secure side wall bottom plate to floor using 3" nails (Fig. A). Nails Nail " nails first. " (5,1 cm) Nails Fig. A 3" Nails into bottom plate. 5 You have finished standing your BACK WALL.

23 PARTS REQUIRED (TEMPORARY): BOA x 4 x 93-3/16" (5,1 x 10, x 36,7 cm) Stand front wall on floor. FRONT WALL INSTALLATION x8 x4 0 " (5,1 cm) 1 Center front wall assembly on the 10" front floor dimension. Use () BOA as temporary braces. Level wall and secure BOA with two 3" screws. 10" (304,8 cm) Screws x4 3 4 First, nail lower edge of panel to floor frame using " nails 6" apart. Angle nail to hit floor frame (Fig. A). Secure front wall bottom plates to floor using (8) 3" nails (Fig. A). BOA 3" Nails into bottom plate. Nail " nails first. " (5,1 cm) Nails Nails Fig. A 5 You have finished standing your FRONT WALL. 3

24 PARTS REQUIRED: BMA SP TM BNA DOUBLER INSTALLATION x 4 x 45-5/8" (5,1 x 10, x 115,8 cm) 8 x 4 x 48" (5,1 x 10, x 1 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) x 4 x 74-1/4" (5,1 x 10, x 188,6 cm) 1 For back wall, orient parts on flat on top of wall frame. BE SURE DOUBLERS ARE FLUSH. Use two 3" nails at each stud and four 3" nails at seam. TM Nails SP Stagger seams 3 For front wall, use 3" nails as shown. Use (4) 3" nails at seam. BE SURE DOUBLERS ARE FLUSH. BMA Nails BNA Stagger seams 4 You have finished installing your DOUBLERS. 4

25 PARTS REQUIRED: BOA x 4 x 93-3/16" (5,1 x 10, x 36,7 cm) OUTER RAFTER INSTALLATION x8 1 Rest one outer rafter on front and back wall doublers. Ensure rafter is flush to back wall panel (Fig. A) and flush to end of back wall doubler (Fig. B). Secure back of outer rafter using 3" screw installed centered into outer rafter end (Fig. A) and afterwards toenailed into inside of rafter (Fig. B). DO NOT OVER-DRIVE SCREW THROUGH PANEL. 3 Orient front of outer rafter flush to front wall panel (Fig. C) and flush to end of front wall doubler (Fig. D). 4 Secure front of outer rafter using 3" screws installed centered into outer rafter end (Fig. C) and afterwards toenailed into inside of rafter (Fig. D). Screw Screw BOA Screw Fig. C Screw toenailed BOA Fig. D Screw 5 6 Repeat steps 1 through 4 for opposite side outer rafter. Remove all temporary braces. Fig. B Screw toenailed Fig. A 7 You have finished installing your outer rafters. 5

26 PARTS REQUIRED: x7 BOA x 4 x 93-3/16" (5,1 x 10, x 36,7 cm) RAFTERS x4 Starting at end as shown, measure and mark location of each rafter Place rafter on front and back wall doublers. Line up rafter centered with marks. Ensure rafter is flush to back wall panel (Fig. A) and flush down on top of back wall doubler (Fig. B). Secure back of rafter using 3" screw installed centered into outer rafter end (Fig. A). DO NOT OVER-DRIVE SCREW THROUGH PANEL. Line up rafter centered with marks on front doubler. Ensure rafter is flush to front wall panel (Fig. C). and resting flush on top of front doubler (Fig. C). Secure front of rafter using 3" screw installed centered into outer rafter end (Fig. C). Toenail each end of rafter into doubler using 3" screws (Fig. B, Fig. D). HERE 10" (5,4 cm) 6" (66,1 cm) 4" (106,7 cm) 58" (147,4 cm) 74" (188 cm) 90" (8,6 cm) 106" (69,3 cm) Screw Fig. C Screws toenailed Fig. D Screw Fig. A 6 Repeat steps through 5 to install (6) remaining rafters. 7 You have finished installing your rafters. Fig. B Screws toenailed 6

27 PARTS REQUIRED: x9 BRA x 3 x 10-1/" (5,1 x 7,6 x 6,7 cm) RAFTER EXTENSIONS 1 Locate rafter extension above top of front wall panels (Fig B). Use another rafter extension (BRA) as a guide to line-up rafter extension with top of main rafter (Fig A). Secure rafter extension using () 3" screws toenailed through front wall panel into BRA (Fig. B). DO NOT OVER-DRIVE SCREW THROUGH PANEL. 3 Repeat steps 1 and to install remaining (8) rafter extensions. Screws toenailed Screw TOP VIEW Screws Fig. A Fig. B 4 You have finished installing your RAFTER EXTENSIONS. 7

28 SIDE WALL PANELS PARTS REQUIRED: x3 " (5,1 cm) 3/8 x 48 x 96" (1 x 11,9 x 43,8 cm) 3/8 x 48 x 96" (1 x 11,9 x 43,8 cm) 3/8 x 4 x 83" (1 x 106,7 x 10,9 cm) 3/8 x 4 x 83" (1 x 106,7 x 10,9 cm) 1-1/" (3, cm) 1 Place 48 x 96" panel onto side wall flush with front wall stud and flush to bottom front wall sheathing, with 1" overhang and with primed side up as shown. Secure panel with two " nails in the corners (Fig. A). Ensure the measurement between the panel edges are the same along the entire length (Fig. B). Angle nails to hit floor frame (Fig. C). Move to the top of panel. Using the long edge of the panel as a lever move the panel side-to-side until top of panel is flush with front wall stud. Secure upper corner with (1) 1-1/" nail into rafter (Fig. D). Ensure 1" panel overhang at bottom of panel (Fig. D). Primed side up Fig. A 1-1/" Nail Fig. D Same Measurement " Nails Fig. B 48" (11,9 cm) 1" (,5 cm) Fig. C 1" (,5 cm) 3 Place 4 x 83" panel onto side wall flush with bottom of 48 x 96" panel with primed side up, as shown. Secure panel with " nails in three corners (Fig. E). Ensure the measurement between the panel edges are the same along the entire length (Fig. B). Angle nails to hit floor frame (Fig. C). Fig. E Primed side up Same Measurement Fig. C 1-1/" Nails Fig. B " Nail 4" (106,7 cm) 4 Repeat steps 1, and 3 to attach the opposite side panels. 8

29 PARTS REQUIRED: SIDE WALL PANELS (continued) x45 1-1/" (3, cm) 6 " (5,1 cm) 5 Nail lower edge of panel to floor using " nails 6" apart. Angle nail to hit floor frame (Fig. A). 6 Nail side wall panels to rafter and wall studs using 1-1/" nails 6" apart as shown. 6" (15, cm) 1-1/" (3, cm) Nails 6" (15, cm) 1-1/" (3, cm) Nails 6" (15, cm) 1-1/" (3, cm) Nails " (5,1 cm) Nails 6" (15, cm) " (5,1 cm) Nail Fig. A 7 Repeat steps 1 and to attach the opposite side panels. 8 You have TEMPORARILY finished installing your side panels. Proceed to install SIDE WALL STUDS. 9

30 PARTS REQUIRED: BFA x 4 x 7-5/8" (5,1 x 10, x 184,5 cm) BJA x 4 x 79-1/8" (5,1 x 10, x 01,3 cm) BKA x 4 x 85-1/" (5,1 x 10, x 17, cm) SIDE WALL STUDS 8 1 Install BJA centered at seam of side wall panels (Fig A). Use a square to ensure 90 degree squareness of studs (BKA, BFA and BJA). to rafter Center BKA on seam of wall panels. to rafter Fig. A to rafter BKA BJA BFA MARK Mark locations of studs and ensure 90 degrees angle at top of each stud. Screw Secure side wall studs with 3" screws into end rafters and floor frame (Fig B). Fig. B 3 Repeat steps 1 and to attach the opposite side SIDE WALL STUDS. 4 You have finished installing your SIDE WALL STUDS. Proceed to finish nailing side wall panels. 30

31 PARTS REQUIRED: SIDE WALL PANELS (continued) x58 1-1/" (3, cm) 9 9 Measure, align and mark side wall studs 4" from center of panel seam and as shown. Nail side wall panels to inside wall studs using 1-1/" nails 6" apart along panel seam and 1" apart in middle of panels as shown. 4" (61 cm) 4" (61 cm) 1-1/" (3, cm) Nails 6" (15, cm) 1" (30,5 cm) 10 Repeat step 9 to nail the opposite side panels. 11 You have finished nailing your SIDE WALL PANELS. 31

32 ROOF PANELS PARTS REQUIRED: GAA x4 " (5,1 cm) 3/4" GAUGE BLOCK 7/16 x 48 x 96" (1,1 x 11,9 x 44 cm) Roof panels may cause serious injury until securely fastened. You must square the roof by attaching one panel first. You will use the panels long edge as a lever to bring your roof into square. Commonly known as racking. 1 Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with 1/" (1,3 cm) measurement overhanging the rafter extension (Fig B) and the panel is 3/4" (1,9 cm) along the the length of the rafter (Fig. A). Nail panel with two nails as shown. 48 x 96" (11,9 x 44 cm) 48" (11,9 cm) NOTE: Measurement from rafter extension. 1/" (1,3 cm) Fig. B Two Nails Fig. A Gauge Block Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until the top corner is at 1/" (1,3 cm) measurement overhanging the rafter extension (Fig B). You may need to move your entire roof frame to make panel line up with 1/" overhang measurement (Fig. B). Secure panel with two " nails into rafters. Two Nails 3/4" (1,9 cm) NOTE: Measurement from rafter extension. 1/" (1,3 cm) Fig. B 3

33 1" (30,5 cm) ROOF PANELS PARTS REQUIRED: 7/16 x 11-7/8 x 36-3/8 (1,1 x 30, x 9,4 cm) 0 " (5,1 cm) 3 7/16 x 48 x 96" (1,1 x 11,9 x 44 cm) 7/16 x 36-3/8 x 96" (1,1 x 9,4 x 44 cm) 7/16 x 11-7/8 x 96" (1,1 x 30, x 44 cm) Nail the first 48 x 96" roof panel using " nails 6" apart on edge and 1" apart inside panel. Locate the second 48 x 96" roof panel with the rough side up flush to first panel along edge and at both corners (Fig. C, D). Repeat nailing pattern. Fig. C 1" (30,5 cm) 6" (15, cm) Fig. D 48 x 96" (11,9 x 44 cm) 6" (15, cm) 4 Nail the 36-3/8 x 96" roof panel with the rough side up using " nails 6" apart on edge and 1" apart inside panel. Ensure the 36-3/8 x 96" roof panel is flush to installed 48 x 96" roof panels and overhang is at 1/" (Fig. B, E). Fig. B 1/" (1,3 cm) 5 Nail the 11-7/8 x 96" roof panel with the rough side up using " nails 6" apart on edges. Ensure the 11-7/8 x 96" roof panel is flush to installed roof panels (Fig. E). 6" (15, cm) 1" (30,5 cm) 6 Nail the 11-7/8 x 36-3/8" roof panel with the rough side up using " nails 6" apart on edges. Ensure the 11-7/8 x 36-3/8" roof panel is flush to all (3) installed roof panels (Fig. E). 11-7/8 x 96" (30, x 44 cm) Fig. E 11-7/8 x 36-3/8" (30, x 9,4 cm) 6" (15, cm) 6" (15, cm) 36-3/8 x 96" (9,4 x 44 cm) 33

34 ROOF PANELS PARTS REQUIRED: " (5,1 cm) 7 Line up each rafter extension 90 degrees square with roof rafters as shown. Secure rafter extensions with screws through roof panels (Fig. A). At roof panel seams use 4 screws (Fig. B). Fig. B Fig. A 90 o SQUARE SQUARE 8 You have finished installing your ROOF PANELS. 34

35 PARTS REQUIRED: BPA 1 x 3 x 33-1/8" (,5 x 7,6 x 84,1 cm) HJ 1 x 3 x 7" (,5 x 7,6 x 18,8 cm) GABLE RAKE FRAMING 6 " (5,1 cm) 1 Align BPA edge flush with BRA (Fig A). Attach with (3) " nails (Fig B). Attach HJ flush with BPA with (5) " nails. (Fig A,B) 3 Repeat Steps 1- on opposite side. 4 You have finished installing your gable rake framing. Angled Ends at seam " finish nail BRA Fig. B HJ BPA Fig. A 35

36 PARTS REQUIRED: BUA 19/3 x 3-1/ x 5-3/8" (1,5 x 8,8 x 133 cm) BTA 19/3 x 3-1/ x 80" (1,5 x 8,8 x 03, cm) FRONT EAVE FASCIA TRIM 0 " (5,1 cm) 1 Attach BUA to BRA (Fig. A, C). Extend approximately 1/4" beyond roof panel (Fig.B). Secure BUA with " finish nails (Fig. C). 3 Attach BTA to BRA (Fig. A, C) flush with BUA. Secure with " finish nails. BTA extends approximately 1/4" beyond roof panel (Fig. D). Nail BUA and BTA ends to BRA with (4) " nails (Fig. E). Fig. E 4 You have finished installing your front eave trim. BRA BUA BTA Fig. A BUA BTA BTA 1/4" Fig. D " Finish Nails BRA Fig. C 1/4" BUA Fig. B 36

37 PARTS REQUIRED: BQA x 3 x 33-1/8" (5,1 x 7,6 x 84,1 cm) ZT 19/3 x 3-1/ x 48" (1,5 x 8,8 x 11,9 cm) BXL 19/3 x 3-1/ x 59-1/4" (1,5 x 8,8 x 150,4 cm) BXR 19/3 x 3-1/ x 59-1/4" (1,5 x 8,8 x 150,4 cm) OY x 3 x 7" (5,1 x 7,6 x 18,8 cm) SIDE FASCIA TRIM ASSEMBLY 8 " (5,1 cm) 1 Begin rear Fascia assembly on a flat surface. Place BQA and OY end to end (Fig. A). Fig. A BQA OY Place BXR and ZT flush with BQA and OY. Attach with " finished nails as shown (Fig. B, C). BQA OY Fig. B Edges of BXR and BQA are flush. BXR ZT Fig. C 3 Repeat steps 1- for the opposite side using BXL and ZT. 4 You have finished assembling the side fascia trim. 37

38 SIDE FASCIA TRIM PARTS REQUIRED: x4 " (5,1 cm) " (5,1 cm) 1 Hold the side fascia assembly flush with roof sheathing and front fascia trim (Fig. B). Fig. A Attach assembly underneath roof panels flush with front fascia board using " screws through roof sheathing (Fig. C). Make sure there is a 5-1/4" space as shown. (Fig. C) ASSEMBLED SIDE FASCIA ROOF SHEATHING " Screws ROOF SHEATHING 5-1/4" (13,3 cm) FRONT FASCIA Fig. B Fig. C " Finish Nails Fig. D 3 Nail front fascia to side fascia with () " finished nails (Fig. D). 4 Repeat steps 1-3 on opposite side. 5 You are finished installing your side fascia trim. 38

39 PARTS REQUIRED: FS x 3 x 35-1/4" (5,1 x 7,6 x 89,5 cm) BYA 19/3 x 3-1/ x 35-1/4" (1,5 x 8,8 x 89,5 cm) PT x 3 x 96" (5,1 x 7,6 x 43,8 cm) ZX 19/3 x 3-1/ x 96" (1,5 x 8,8 x 43,8 cm) REAR FASCIA TRIM 0 " (5,1 cm) " (5,1 cm) 1 Place PT and FS flush to roof sheathing and to ZT. (Fig. B, C) " Screw ZT PT OY BYA FS ZX Fig. A Fig. B 3" Screw Fig. C Attach PT and FS with " wood screws through roof sheathing and (1) 3" screw at OY on both ends (Fig. B, C). ZT ZX " Nail " Nails Fig. D BYA or ZX Fig. E 3 Nail BYA and ZX to PT and FS and to ZT using " nails (Fig. A, D, E). 4 You are finished installing your rear fascia trim. 39

40 SOFFIT PARTS REQUIRED: 35-3/4 x 10-3/8 x 3/8" (90,8 x 6,3 x 1 cm) 0 " (5,1 cm) 95-3/8 x 10-3/8 x 3/8" (4, x 6,3 x 1 cm) 95-1/" (4,5 cm) 95-3/8" (4, cm) 95-1/" (4,5 cm) 35-3/4" (90,8 cm) 1 Attach 35-3/4" soffit board under BRA using (6) " finish nails as shown, primed side down (Fig. A, B). Align 95-3/8" soffit board flush with 35-3/4". Attach soffit board with (14) " finished nails underneath BRA (Fig. D). 35-3/4" (90,8 cm) Fig. C BRA " Finish Nails 95-3/8" (4, cm) Fig. A Fig. B 40

41 SOFFIT continued... PARTS REQUIRED: 95-1/ x 5-1/4 x 3/8" (4,5 x 13,3 x 1 cm) 8 " (5,1 cm) 3 Attach 95-1/" soffit board under fascia backer and side rake framing (Fig. C, D) using (14) " nails. 95-1/" (4,5 cm) " Finish Nails 5-1/4" Fig. C Fig. D 4 Repeat Step 3 on opposite side. 5 You have finished installing your soffit panels. 41

42 S PARTS REQUIRED: OO x 3 x 69" (5,1 x 7,6 x 175,3 cm) x4 1-1/4" (3, cm) HINT: Look for 3/8" SPACER attached to doors. Left Door Right Door GAA 1 x 3 x 5" (,5 x 7,6 x 1,7 cm) 1 3 Orient parts as shown on flat surface. (right) and green (left) on hinge board. 3/8" offset is to top. Look for red Attach temporary support OO with 3" screws in middle and at ends as shown. Tighten securely. Attach temporary support GAA with two 1-1/4" screws as shown. Tighten securely. OFFSET 3/8" (1 cm) GREEN Make sure spacer is attached. 3/8" (1 cm) RED OFFSET 3/8" (1 cm) 3-1/" (59,7 cm) (4) Screws OO Tighten screws securely. Screws 1-1/4" (3 cm) NOTE: Screw hole will be used later. GAA 3/4" (1,9 cm) 3-1/" (59,7 cm) 3/4" (1,9 cm) 3/8" (1 cm) 4 Bottom edges flush.

43 PARTS REQUIRED: OO x 3 x 69" (5,1 x 7,6 x 175,3 cm) S 3 4 Attach temporary support OO as a ledger board flush under wall panels for doors to rest on using 3" screws (Fig. A). OO Fig. A against wall panels OO 5 6 Center doors on panel seam as shown (Fig. B). Check ledger board is still flush under panels. Screw hinge boards into wall frame and floor using ten 3" screws as shown. Make sure screws go into framing and floor (Fig. C, D). 7 Remove temporary supports and check doors open properly. 8 You have finished installing your doors. Seam 3/8" (1 cm) Fig. B Fig. C Angle Screw Screws into the wall support and floor frame. Fig. D 43

44 PARTS REQUIRED: x4 AH 19/3 x -1/ x 6-5/8" (1,5 x 6,3 x 67,6 cm) x44 3/4" (1,9 cm) Place AH 9" from top and lower cross brace and level (Fig. B). Secure from behind using three 3/4" screws. Repeat step 1- to attach two AH's to other door. Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown in Fig. B. Use two screws at seams. You have finished securing your door and trim. Door Panel Center Nail into framing. Hinge Board Door Trim Fig. A 9" (,8 cm) CENTER CENTER AH AH 7 9" (17,8 (,8 cm) 9" (,8cm) Two Screws 9" 7 (,8 (17,8 cm) 44 Fig. B

45 WEATHERSTRIP PARTS REQUIRED: OO x 3 x 69" (5,1 x 7,6 x 175,3 cm) 0 " (5,1 cm) 1 With left door closed, center a weatherstrip OO vertically on the left door in the door opening (Fig. A). OO will offset the left door 1" OUT past the door trim 1" (Fig. B). 3 4 Secure OO using five 3" screws through outside trim into OO (Fig. B) On right door center OO vertically in door opening (Fig. A). OO will offset the right door 1" IN from the door trim (Fig. C). Secure OO using five 3" screws through outside trim into OO (Fig. C). 5 You have finished installing your door weatherstrips. 1" (,5 cm) OFFSET OO Center OO in door opening. Fig. A OFFSET 1" (,5 cm) Fig. B Fig. C Screws " (5,1 cm) Screws " (5,1 cm) 0 17" (43,1 cm) Approximately 45

46 PARTS REQUIRED: x8 1" (,5 cm) 5/16" (0,8 cm) Drill Bit 1 Place bolt onto OO in open position with bolt end 3/8" down from frame. Bolt is open when loop is contacting base (Fig A). Mark and pre-drill holes for screws. 3 4 Install bolt with screws supplied and drill 5/16" hole for bolt to extend into. Place bolt onto OO in open position with bolt end 1/" up from floor. Bolt is open when loop is contacting base (Fig B). Mark and pre-drill holes for screws. Install bolt with screws supplied and drill 5/16" hole for bolt to extend into. Fig. A 5 You have finished installing your barrel bolts. LOCATE AND PRE-DRILL HOLES TO AVOID SPLITTING WOOD OVER FRAME 5/16" drill for bolt: 1" deep. OO x 3 x 69" 3/8" with bolt in open position. x4 OPEN POSITION, Spring is loose. PRE-DRILL (4) HOLES LEFT Loop contacts base. Loop contacts base. OO x 3 x 69" x4 OPEN POSITION, Spring is loose. FLOOR 1/" 5/16" drill for bolt: 1" deep. PRE-DRILL (4) HOLES 46 Fig. B

47 PARTS REQUIRED: HARDWARE 1-1/" (3,8 cm) 1/" (1,3 cm) Drill Bit 1/4" (0,6 cm) Drill Bit 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill hole with 1/4" drill. Re-drill hole with 1/" drill. Keep drilled hole square to trim to avoid breaking edge of x3". RIGHT. 1-1/" (3,8 cm) TOP VIEW 35-3/4" 90 cm 1-1/" 3,8 cm Fig. A 1/4" Pre-drill and 1/" Drill-through. 3 Insert handle in hole and secure using 1-1/" (3,8 cm) screws. Attach inside handle and secure with set screw as shown. SET SCREW 1-1/" (3,8 cm) Screws 4 You have finished installing your T-handle and decorative hinges. 47

48 PARTS REQUIRED: x3 9 X 7" (,8 x 68,5 cm) WINDOWS x6 3/4" (1,9 cm) 1 Apply high quality exterior-grade caulk behind frame near edge before installing to seal window. From outside of shed, position window in center of opening and level. Use two screws at top of windows. Do not fully tighten screws. Screws per window Screws per window HINT: Caulk behind frame near edge before installing. Approximately 1" (,5 cm) You must caulk around windows to validate warranty. 48

49 TRIM PARTS REQUIRED: BSA 19/3 x -1/ x 91" (1,5 x 6,3 x 31,1 cm) x4 EY WINDOWS 19/3 x -1/ x 9" (1,5 x 6,4 x,9 cm) 9 " (5,1 cm) 3 Center BSA over door. Secure using (7) " finish nails as shown. Do not nail into window flange. Mark Center BSA Centered 3/4" (1,9 cm) 4 Position EY at ends and in between window frame as shown. Secure using (8) " finish nails. Remove 1-1/4" screws. Remove screws Remove screws EY x4 FRAMING BEYOND 6-1/" (78,7 cm) Centered 5 Position BSA centered on window frame as shown. Secure using (4) " finish nails. BSA Centered FRAMING BEYOND 49

50 WINDOWS PARTS REQUIRED: 3/4" (1,9 cm) 6 Install (1) 3/4" screws from inside, as shown. Do not screw into window flange. Install 3/4" (1,9 cm) screws from inside. FRAMING BEYOND INSIDE OF SHED Install 3/4" (1,9 cm) screws from inside. 7 You have finished installing your window. 50

51 BACK CORNER TRIM PARTS REQUIRED: 3/8 x x 68-3/4" (0,9 x 5,1 x 174,6 cm) 3/8 x x 69-1/4" (0,9 x 5,1 x 175,8 cm) 3/8 x x 69-1/4" (0,9 x 5,1 x 175,8 cm) 4 " (5,1 cm) 1 Place 68-3/4" back corner trim flush to bottom of back soffit board (Fig. A, B, F) and flush with side panel along the length (Fig. A). Attach using (6) " finish nails into corner wall framing (Fig. A, C). Space nails equally (Fig. C). Place 69-1/4" back side corner trim angled end up (Fig. E) flush up under side soffit panel and flush with back corner trim along the length (Fig. E). Attach trim using (6) " finish nails into corner wall stud (Fig. D, C). Space nails equally (Fig. C). at soffit board. Fig. B at top Fig. A " Nail Fig. F 68-3/4" (174,6 cm) 69-1/4" (175,8 cm) Fig. C " x 68-3/4" Corner Trim BACK OF SHED with side wall panel. (Angled End up) Angled end at soffit. 68-3/4" (174,6 cm) Fig. E Fig. D Seam is flush. Caulk seam before painting trim. 69-1/4" (175,8 cm) 3 Repeat for other side. " Nail with back corner trim. 4 You have attached your back corner trim. 51

52 PARTS REQUIRED: 3/8 x x 5-3/8" (0,9 x 5,1 x 64,4 cm) 3/8 x x 96" (0,9 x 5,1 x 43,8 cm) FRONT FRIEZE TRIM " (5,1 cm) 1 Attach 5-3/8" (64,4 cm) and 96" (43,8 cm) front horizontal frieze boards using " finish nails as shown (Fig. A). Leave 3/8" (0,95 cm) overhang on both ends (Fig. B). Fig. B Fig. A 5-3/8" (174,6 cm) 96" (43,8 cm) 3/8" (0,95 cm) You have finished attaching your front frieze trim. 5

53 PARTS REQUIRED: 3/8 x x 91-1/4" (0,9 x 5,1 x 31,7 cm) FRONT CORNER TRIM " (5,1 cm) 1 Attach both vertical 91-1/4" (31,7 cm) front corner trim on both sides, flush to bottom edge of previously installed horizontal frieze trim using (6) " nails per trim (Fig. A, B, C). 91-1/4" (31,7 cm) 3/8" (0,95 cm) Fig. B Fig. A Fig. C You have finished attaching your front trim boards. 53

54 PARTS REQUIRED: 3/8 x x 93-1/4" (0,9 x 5,1 x 36,8 cm) 3/8 x x 93-1/4" (0,9 x 5,1 x 36,8 cm) FRONT SIDE TRIM " (5,1 cm) 1 Attach 93-1/4" (36,8 cm) front side corner trims on both sides flush with front frieze trim. Use (6) " (5,1 cm) nails to secure side trim to side wall (Fig. A, B, C). Fig. B Fig. A Fig. C You have finished attaching your front side trim boards. 54

55 VENTS PARTS REQUIRED: 8 x 16" (0,3 x 35,6 cm) 1/" (1,3 cm) 1 Locate and mark for two vents in side walls as shown. (1) at top and (1) at bottom Cut out marked openings. Caulk behind vent flanges. Secure using 1/" (1,3 cm) screws. You have finished installing your vents. 3 4" (10,1 cm) 6" (15, cm) Caulk 14" (35,6 cm) 4" (10,1 cm) 14" (35,6 cm) 4" (10,1 cm) Caulk 6" (15, cm) 3 5" (7,6 1,7 cm) 55

56 PAINT & CAULK - NOT INCLUDED - Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: Bottom edge of all siding and trim Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting. (Follow directions provided by manufacturer.) ROOF FELT - NOT INCLUDED - Install felt flush to all roof edges overlapping 3". Use minimal amount of roofing nails to hold in place. 3" OVERLAP You must install roof felt to validate warranty. DRIP EDGE - NOT INCLUDED - Install drip edge over roof felt on side of shed and under roof felt on back side (Fig. A). Do not use nails on side of drip edge that hangs over side of building. Only nail top of drip edge as shown. Roof Felt Drip Edge Drip Edge Fig. A Drip Edge flush to trim. (Follow directions provided by manufacturer.) You must install drip edge to validate warranty. SIDE OF SHED BACK OF SHED 56

57 SHINGLES - NOT INCLUDED - Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN Notch 1" (,5 cm) 1/" (1,3 cm) Sealing Strip 1" (,5 cm) Half A Rain Slot 1 Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. Install first starter row upside down, color up and flush to drip edge at bottom of roof panel. Use (4) nails per shingle. Starter row must be straight and level all the way across with lower edge of roof deck. (4) Nails TABS UP START HERE Shingle overlaps roof decking. to drip edge. BACK OF SHED Begin where indicated on image below, install first row of shingles with notch flush with drip edge. Drip Edge Notch 1" (,5 cm) to drip edge. with starter row. BACK OF SHED 57

58 3 SHINGLES continued... Install second row of shingles flush at top of first row's rain slots. Ensure flush to drip edge at front side, stagger each row. 4 Notch with rain slots. Continue installing rows of shingles by staggering at front. 1" (,5 cm) BACK OF SHED with rain slots. Notch BACK OF SHED 5 Continue installing rows of shingles to the front of the shed. At the front edge of the shed make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at front roof edge cut to roof edge with a utility knife. 5" (1,7 cm) Cut Cut Off. Top of rain slot. 5" (1,7 cm) or less. If more than 5" to rain slot you must install another row of shingles. 6 Using your shingle hooked blade carefully cut shingles along chalk line. 58

59 SHINGLES - DRIP EDGE 7 Install drip edge over top shingle row with 1" overhang over roof edge. 1" (,5 cm) 8 Using your shingle hooked blade carefully cut shingles on a flat surface along the rain slots, using a chalk line for reference. 9 Align remaining shingles with edge of the front drip edge. 10 You have finished shingling your roof. 59

60 WARRANTY Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for one year.. All hardware and metal components are warranted for two years. 3. Trim is warranted for 15 years. 4. Waferboard siding and sheathing is warranted for two years. 5. SmartSide siding is warranted for 15 years on all Marco series buildings and 15 years on all Premier Series buildings. 6. Timber series buildings siding and trim are warranted for 10 years. 7. Solar Shed windows are warranted for 1 year. 8. Cedar lumber is warranted for 15 years. 9. Cedar doors and Cedar Garden Center are warranted for 10 years. 10. Metal roof is warranted for 5 years. Backyard Storage Solutions, LLC will repair, replace or pay for the affected part. In no event shall Backyard Storage Solutions, LLC pay the cost of labor or installation or any other costs related thereto. All warranties are from date of purchase. If a cash refund is paid on an affected part, it will be prorated from the date of purchase. CONDITIONS The warranty is effective only when: 1. The unit has been erected in accordance with the assembly instructions.. The unit has been properly shingled and painted or stained and reasonably and regularly maintained thereafter. 3. The failure occurs when the unit is owned by the original purchaser. 4. Backyard Storage Solutions, LLC has received the warranty registration card within thirty (30) days of purchase and notification of the failure in writing within the warranty period specified above. 5. Backyard Storage Solutions, LLC has had reasonable opportunity during the sixty (60) days following receipt of notification to inspect and verify the failure prior to commencement of any repair work. 6. Drip edge and felt are installed. REQUIREMENTS Storage Buildings & Playhouses To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit; shingle the roof and paint or solid-colored stain the siding using 100% acrylic latex exterior product with a minimum of two () coats within thirty (30) days of assembly; caulk above all doors and all horizontal and vertical trim boards; paint and seal all exposed edges, sides and faces of SmartSide and waferboard siding to include all exterior walls and all sides and all edges of doors. Gazebos, Pergolas & Timber Buildings To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit. This includes treating all of the exposed cedar and pine surfaces on your gazebo or timber building with an exterior grade wood preservative, an exterior oil-based semi-transparent stain, an acrylic latex exterior paint or an acrylic latex solid color exterior stain within 30 days of assembly and as needed thereafter to maintain your warranty. Keep vegetation trimmed away from building and make sure siding panels and trim do not come in contact with masonry or cement. The minimum ground clearance for siding must be one half inch (½ inch) from concrete slab or two and one half inches ( ½ ) from the ground when building is erected or constructed on a treated wood floor kit. Water from sprinklers must be kept off unit. In no event will Backyard Storage Solutions, LLC be responsible for any indirect, incidental, consequential or special damages nor for failure(s) that are caused by events, acts or omissions beyond our control including, but not limited to, misuse or improper assembly, improper maintenance (which eventually leads to rot or decay) and acts of God. Backyard Storage Solutions, LLC will not be held responsible for any labor costs incurred to construct your unit. This warranty gives you certain specific rights that vary from state to state. CLAIM PROCEDURE To make a claim under this warranty, you can either call or prepare a letter. Please have ready the information below when you call or include the information when writing: 1. The model and size of the product.. A list of the part(s) for which the claim is made. 3. Proof of purchase of the Backyard Storage Solutions, LLC item, as shown on the original invoice. 4. Run code, as listed on the yellow warranty card enclosed in the product package. Mail the above information to: Backyard Storage Solutions, LLC Attn: Customer Service 1000 Ternes Monroe, MI 4816 *WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A. IMPORTANT: This is your warranty certificate. Please complete and mail your warranty card to properly validate your warranty. 60 Limited Conditional Warranty *