Belhaven 2-Drawer File Model # BEH2DF

Transcription

1 LOT NUMBER: DATE PURCHASED: / / Belhaven 2-Drawer File ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday Or visit our web site 24 hours a day, 7 days a week for product assistance at Or your request to parts@whalenfurniture.com THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Whalen Furniture Mfg., Inc. Page 1 Factory # 16452

2 MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture CATALOG: Belhaven 2-Drawer File (BEH2DF) DATE OF MANUFACTURE: August 2012 MADE IN CHINA MAXIMUM LOAD 100 lb. (45.3 kg) MAXIMUM LOAD 30 lb. (13.6 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY. QUALITY GUARANTEE We are confident that you will be delighted with your Whalen Furniture purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from State to State. Customer Service: :30 a.m. - 4:30 p.m., PST, Monday to Friday Whalen Furniture Mfg., Inc. Page 2 Factory # 16452

3 FURNITURE TIPPING RESTRAINT YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES. THIS HARDWARE, MUST BE PROPERLY INSTALLED (FOLLOW ALL DIRECTIONS IN ORDER ON THE PLASTIC BAG), TO PROVIDE PROTECTION AGAINST THE UNEXPECTED TIPPING OF FURNITURE DUE TO IMPROPER USE. THIS PRODUCT IS ONLY A DETERRENT. IT IS NOT A SUBSTITUTE FOR PROPER ADULT SUPERVISION. USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE, THE RISK OF TIP-OVER. Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture. Further advice about wood furniture care It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages. We hope you enjoy your purchase for many years. Whalen Furniture Mfg., Inc. Page 3 Factory # 16452

4 Parts and Hardware List Please read completely through the instructions and verify that all parts listed are present before beginning assembly. A- FILE CABINET (1) (1) - PLASTIC ANCHOR (1) (2) - BRACKET (2) (3) - LONG SCREW (1) (4) - SHORT SCREW (1) (5) - NYLON RESTRAINT (1) TOUCH-UP PEN (1) A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping. Whalen Furniture Mfg., Inc. Page 4 Factory # 16452

5 DRAWER INSTALLATION If you need to remove the file drawer or keyboard tray with ball bearing slides from the unit, please follow the steps below to prevent any damage to the slides or the drawers. 1. If you need to remove the drawer, please pull the drawer all the way out, then simultaneously push the plastic release lever of the ball bearing slide up on one side and down on the other side, and pull the drawer completely out. See detail #A. 2. To place the drawer back, simply push the ball bearing cart all the way to the end of the slides (on both sides), and align the slide runners on the drawer with the slide tracks on the unit. Push it carefully inside until it stops. See detail #B. NOTE: If the drawer does not go in smoothly, please take it out and repeat the step. Whalen Furniture Mfg., Inc. Page 5 Factory # 16452

6 Assembly Instructions Tools required: Phillips Screwdriver, Mallet, Power Drill, and 3/8 Drill Bit 1. Unpack the unit and confirm you have all the hardware and parts required. NOTE: Must install the wall mounting hardware with the products in use. 2. Position the FILE CABINET (A) close to the wall on your desired location. 3. In case of uneven floor, FLOOR LEVELERS are provided at the bottom of the CABINET. Adjust the FLOOR LEVELERS by hand to correct tilting, until the unit is level. 4. Attach one of the MOUNTING BRACKETS (2) securely to the back edge of the furniture with the SHORT SCREW (4). 5. Determine where the furniture is to be placed and mark location on the wall for the MOUNTING BRACKET screw hole approximately 2 below the BRACKET (2) mounted to the edge of the furniture. 6. Drill a 3/8 hole in the wall. Press the PLASTIC ANCHOR (1) into the hole and gently tap until the flange of the anchor is against the wall surface. 7. Position the BRACKET (2) over the PLASTIC ANCHOR (1) and use the LONG SCREW (3) to securely attach the BRACKET to the wall. 8. Place the furniture so the BRACKET in the back edge is in line with the BRACKET in the wall. 9. Lace an end of the NYLON RESTRAINT (5) strap down through each BRACKET. Bring both ends together and slice the beaded end of the strap through the keyhole shaped slot on the other end until snug. Pull down on the beaded end until it snaps lock into the keyhole slot. 10. To double lock return the beaded end back through the keyhole as shown. 11. Check to make sure the strap is securely laced and locked to the BRACKETS. Your assembly should now be complete. Thank you for your purchase! Whalen Furniture Mfg., Inc. Page 6 Factory # 16452

7 IF YOU NEED TO ORDER ANY PARTS PLEASE USE THE LIST BELOW Belhaven 2-Drawer File (BEH2DF) *BEH2DF-1-TD Top Drawer *BEH2DF-2-BD Bottom Drawer *BEH2DF-3-LK Lock & Keys *BEH2DF-4-HB Handle w/bolt *BEH2DF-5-FH File Hanger *BEH2DF-6-DS Drawer Slides *BEH2DF-7-TRHK Tipping Restraint Hardware Kit *BEH2DF-8-TUP Touch-up Pen *BEH2DF-9-FL Floor Leveler