CCT (K) PLG2-Ar x245-DC > PLG2-Ar x245-DC > CCT (K)

Transcription

1 Light Engines 2250lm on 495 x 245mm Dimension (l x w x h): 495mm x 245mm x 6mm Benefits Efficiency 150lm/W Homogeneous light distribution Consistent white light of 3 SDCM Seamless: no shadows between modules Poke-in connectors for 0,5mm² to 0,75mm² wire Self-cooling SELV/non-SELV module for easier fixture design Average lifetime h L80B10 at Tp = 55 C CE, ENEC approval under preparation Applications Office, Industry Floors, Corridors Public area Typical technical current* Product name Flux (lm) CCT (K) CRI SDCM Vf (V) If (ma) P (W) lm/w PLG2-Ar x245-DC > PLG2-Ar x245-DC > Typical values valid for Tp 45 C Typical current* Product name Flux (lm) CCT (K) CRI SDCM Vf (V) If (ma) P (W) lm/w PLG2-Ar x245-DC > PLG2-Ar x245-DC > Typical values valid for Tp 45 C Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. * Typical value; tolerance for optical and electrical data: +/-10%, 08/2015 page 1 of 7

2 Optical parameters Product name # LED Pitch (mm) PLG2-Ar x245-DC 60 53mm x 43mm PLG2-Ar x245-DC 60 53mm x 43mm Minimum and Maximum Ratings Product Storage temperature [ C ] Tc max.* (@ typ. current) L80 Tp 55 C PLG2-Ar x245-DC C 50,000h PLG2-Ar x245-DC C 50,000h, The modules are designed for operation with OPTOTRONIC ECG. *) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the light engine. The temperature of the LED module must be measured at the tc-point according to EN in thermally settled conditions with a temperature sensor. For exact location of the Tc -point see drawing below (marked as Tc1 and Tc2). Temperature derating 104,0% 102,0% Relative Flux and Efficacy 100,0% 98,0% 96,0% 94,0% Luminous Flux Efficacy 92,0% T case ( o C), 08/2015 page 2 of 7

3 L80B10 lifetime [h] as a function of Tp Modularity OT FIT CS (triple current driver SELV) is designed to be operated by OT FIT SELV drivers in parallel connection*. Current setting via cable bridge (linear drivers) or selectable output current connectors (compact drivers). OT FIT 27V 54V OT FIT 80 / / 1A6 CS L Linear drivers OT FIT 50 / / 1A0 CS L OT FIT 35 / / 0A7 CS Compact drivers OTe 25/ /420 CS OTe 25/ /700 CS 1,2A / 1,4A / 1,55A 0,8A / 0,93A / 1,0A 0,5A / 0,6A / 0,7A 290 / 350 / 420 ma 500 / 600 / 700 ma 360 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm 88 x 43 x 29.5 mm 88 x 43 x 29.5 mm 2250lm 4 (2), , 08/2015 page 3 of 7

4 OTi DALI (wide window driver SELV) is designed to be operated by OTi DALI drivers in parallel connection*. Current setting via resistor coding (LEDSet) or Tuner4TRONIC software and DALI magic**. OTi DALI 27V 54V OTi DALI 80/ /1A6 LT2 L OTi DALI 50/ /1A4 LT2 L OTi DALI 35/ /700 LT2 L 0,6A - 1,55A 0,6A - 1,4A 0,2A 0,7A 360 x 30 x 21mm 360 x 30 x 21mm 360 x 30 x 21mm 2250lm 2,3,4 2,3 1,2 OT FIT D (single current driver Non-SELV) is designed to be operated by OT Fit D Non-SELV drivers in serial connection*. OT Fit D OT FIT 50/ /350 D L 250mA, 54V 216V 2250lm 210 x 30 x 21mm 1,2,3 (Xs1p) OTi (wide window driver Non-SELV) is designed to be operated by OTi and OTi DALI drivers in serial or combined serial-parallel connection*. Current setting via resistor coding (LEDSet) and for OTi DALI drivers also via Tuner4TRONIC software and DALI magic. OTi 54V-240V OTi 60/ /550 D LT2 L OTi 90/ V/1A0 D LT2 L OTi DALI OTi DALI 90 1A0 120mA 550mA 250mA 1000mA 125mA 550mA 250mA 1000mA 280 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm 280 x 30 x 21mm 2250lm 2,3,4 (Xs1p) 2,3,4,5 (Xs1p) 6 (3s2p) 2,3,4 (Xs1p) 2,3,4,5 (Xs1p) 6 (3s2p), 08/2015 page 4 of 7

5 Installation examples Connection scenarios of the module as shown below are based most common applications. Many other scenarios, e.g. 3 modules by 1s3p or 3s1p, are possible. If you have any further questions about installation of Light engines, consult your local Osram Sales representative. 1. Parallel connection 600 x 600 luminaire (1s2p configuration) 1200 x 300 luminaire (1s2p configuration), 08/2015 page 5 of 7

6 2. Serial connection 600 x 600 luminaire (2s1p configuration) 1200 x 300 luminaire (2s1p configuration) Drawings Mounting hole No mounting hole, 08/2015 page 6 of 7

7 Safety Information The LED module itself and all its components must not be mechanically stressed. When handling the module without use of mountain screws avoid excessive force on the cover as it may be separated from the PCB. The integrated mounting and locking mechanism on the cover of the module is intended to center and lock a reflector. Excessive force on this mechanism may cause permanent damage to the module. The modules are intended for operation only with matching OPTOTRONIC To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC , EN 55015, IEC and IEC ENEC: and IEC/EN Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") OSRAM OPTOTRONIC electronic control gear complies to all relevant standards and guarantees safe operation. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Pay attention to standard ESD precautions when installing the module. Important information on photobiological safety is available in the application guide. Photobiological safety according to IEC 62471, risk group RG1 Max. Voltage U-OUT = 250V for non-isolated products; Max. Voltage U-OUT = 60V for SELV products Assembly Information For optimum cooling a thermally conducting layer should be applied between module and heat sink. Further details and recommendation for mounting can be found in the application guide. Ordering codes Product name EAN * S-Unit ** PLG2-Ar x245-DC x 1 PLG2-Ar x245-DC x 1 *) EAN: Ordering number per single PRODUCT **) S-Unit: products per shipping unit Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. Sales and Technical Support OSRAM GmbH Marcel-Breuer-Straße 6 D München Deutschland Sales and technical support is given by the local OSRAM subsidiaries. On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers., 08/2015 page 7 of 7