Biax S and S/E. Compact Fluorescent Lamps Non-Integrated 5W, 7W, 9W and 11W. GE Lighting DATA SHEET. Product information. Features.

Transcription

1 GE Lighting Biax S and S/E Compact Fluorescent Lamps Non-Integrated 5W, 7W, 9W and 11W DATA SHEET information Biax S compact fluorescent lamps can provide savings of up to 73% in energy costs compared to incandescent lamps. Available in 5, 7, 9 and 11 watt ratings, low wattage Biax S lamps are ideal for new installations or to replace existing incandescent lamps. These lamps are available in 27, 3, 35, 4 and 65K colour temperatures. The Biax S lamps have built-in internal starters. They have a rated average life of 1, hours, which results in fewer lamp changes and a reduction in maintenance costs over the life of an installation. The Biax S/E lamps are available in 5, 7, 9 and 11 watt ratings. However, the Biax S/E lamps have 4-pin caps without built-in capacitors and starters, they are therefore suitable for operation with electronic control gear and can be used for dimming and emergency lighting applications. Biax S/E lamps have the same energy saving benefits and high quality colour rendering as the Biax S range. The use of separate electronic ballasts makes them suitable for almost every kind of energy supply: high and low voltages, accumulators, batteries, solar cells and systems that can be dimmed. When the new fluorescent lamp is installed into dimming system, it is advised to operate lamps for period of hours at full light output. Features Flat and compact High luminous efficacy Up to 73% energy-saving compared to incandescent lamps 1 times the lamp life of incandescent lamps Pleasant light, excellent colour rendering. Application areas Wall & ceiling luminaires In hotels, motels, office buildings, apartments Building, public areas Ideal for task light applications also Emergency lighting Enclosed outdoor fixtures

2 Basic data Wattage Power Energy Volts consumption [V] [kwh/h] Cap Description Code Lamp Efficacy [lm/w] CCT [K] Life on 3h CRI Mercury Standard Diameter [Ra] [mg] Gear [h] Biax S 2-pin, Internal Starter G23 F5BX/SPX27/ , B G23 F5BX/SPX41/ , B G23 F7BX/SPX27/ , A G23 F7BX/ , A G23 F7BX/SPX35/ , A G23 F7BX/SPX41/ , A G23 F7BX/ , A G23 F9BX/ , A G23 F9BX/ , A G23 F9BX/SPX35/ , A G23 F9BX/SPX41/ , A G23 F9BX/ , A G23 F11BX/ , A G23 F11BX/ , A G23 F11BX/ , A G23 F11BX/ , A G23 F11BX/ , A 1 Wattage Power Energy Volts consumption [V] [kwh/h] Cap Description Code Lamp Efficacy [lm/w] CCT [K] CRI [Ra] Mercury [mg] Life on electronic gear 12h cycle (h) Diameter Biax S/E 4-pin, External Starter Required G7 F5BX/827/4P , A G7 F5BX/84/4P , A G7 F7BX/827/4P , A G7 F7BX/84/4P , A G7 F9BX/827/4P , A G7 F9BX/84/4P , A G7 F11BX/827/4P , A G7 F11BX/84/4P , A G7 F11BX/865/4P , A+ 1 Length Length EEC EEC Pack Qty Pack Qty Dimensions L1 L1 Biax S 2pin cap Biax S/E 4pin cap L2 L max. L2 L max. G23 IEC G7 IEC L max Biax S 5W W W W Biax S/E 5W W W W L1 L2 2

3 Lamp life average life for Biax S & S/E lamps is 1, hours (switching cycle: 3 Hrs: 165Mins ON / 15Mins OFF). curve presented for Biax S & S/E lamps is based on lumen readings in a photometric sphere under laboratory conditions, in cap up position. In actual use, lumen output is a function of burning hours and lamp operating watts throughout life. % Survival rate and lumen maintenance 5 W and 7W % Survival rate and lumen maintenance 9W and 11W 9% 9% Survival in % 8% 7% 6% Survival in % 8% 7% 6% 5% 2 4 6, 8, 1, Operating hours 5% 2 4 6, 8, 1, Operating hours , , , , Effect of frequent switching Lamps survive min. 2, switching cycles with appropriate electronic gear or external starter. Effects of supply voltage variations on lamp performance Biax S & S/E lamps are suitable for supplies in the range 2V to 24V, 5Hz for appropriately rated series choke (reactor) ballasts. Supplies outside this range require a transformer (conventional, high reactance or CWA) to ensure correct lamp operation. Lamps start and operate at 1% below the rated supply voltage when the correct control gear is used. However, in order to maximise lamp survival, lumen maintenance and colour uniformity, the supply voltage and ballast design voltage should be within ±3%. Supply variations of ±5% are permissible for short periods only. This may be achieved by measuring mean supply voltage at the installation and selecting ballasts with appropriate settings. Luminous intensity distribution , , , , The luminous intensity distribution curve shows the horizontal light intensity of Biax S & S/E lamps. Radial luminous intensity distribution Percentage [%] Lamp Current Lamp Wattage Luminous Flux Operating Voltage Mains Voltage [V]

4 Effects of temperature changes When installed in a luminaire, the temperature of the air surrounding the lamp cap changes and this can affect the light output of the lamp. The effects of changes in ambient temperature for a typical lamp are in the graph below. output vs. ambient air temperature Relative lumen output percentage Ambient temperature [ C] Spectral distribution Spectral power distribution (27K) Spectral power distribution (3K) Spectral power distribution (35K) Spectral power distribution (4K) Spectral power distribution (65K)

5 Circuit diagrams Parallel compensated B = ballast (5Hz) = lamp holder Parallel compensated E = electronic gear = lamp holder B B E E Supply voltage Supply voltage Supply voltage Supply voltage Biax S 5W, 7W, 9W and 11W Biax S/E 5W, 7W, 9W and 11W Recommended list of ballasts * Wattage Lamp description Ballast manufacturer Single ballast description Twin ballast description Biax S/E 4-pin 5W F5BX/827/4P Tridonic Atco PC 1x5 16 W Basic ELXc Biax S/E 4-pin 7W F7BX/827/4P Tridonic Atco PC 1x5 16 W Basic Hüco EVG 1x7-13W HMC ELXc Biax S/E 4-pin 9W F9BX/827/4P Tridonic Atco PC 1x5 16 W Basic PC 2/9/11 TCS PRO Helvar EL 1/2x9-13TCs EL 1/2x9-13TCs Hüco EVG-HP 1x/2x9-21W HC EVG-HP 1x/2x9-21W HC ELXc Biax S/E 4-pin 11W F11BX/827/4P Tridonic Atco PC 1/9/11 TCS PRO PC 2/9/11 TCS PRO Helvar EL 1/2x9-13TCs EL 1/2x9-13TCs Hüco EVG-HP 1x/2x9-21W HC EVG-HP 1x/2x9-21W HC ELXc *Ballast manufacturers have the right to change ballast specification without prior notification or official announcement so these data based on GE measurement 21/211. 5

6 Compliance Standards IEC IEC or EN 691 IEC or EN CIE S 9/E:22 European Directives CE mark Energy Labelling RoHS WEEE REACH ErP ecodesign Lamp caps and holders together with gauges for the control of interchangeablity and safety Single-capped lamps - performance requirements Single-capped lamps - safety requirements Photobiological safety of lamps and lamp systems 93/68/EEC; LVD: 26/95/EC; Ecodesign 25/32/EC, ROHS 211/65/EU Directive 21/3/EU, 874/212/EU energy labelling of electrical lamps and luminaires Directive 211/65/EU on Restrictions of the use of certain Hazardous Substances (RoHS) Directive 212/19/EU on Waste Electrical and Electronic Equipment (WEEE) Directive 26/197/EC on Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) Directive 25/32/EC, 29/245/EC ecodesign requirements (of Energy-related s) for tertiary sector lamps and General Electric are both registered trademarks of the General Electric Company GE Lighting is constantly developing and improving its products. For this reason, all product descriptions in this brochure are intended as a general guide, and we may change specifications from time to time in the interest of product development, without prior notification or public announcement. All descriptions in this publication present only general particulars of the goods to which they refer and shall not form part of any contract. Data in this guide has been obtained in controlled experimental conditions. However, GE Lighting cannot accept any liability arising from the reliance on such data to the extent permitted. Biax S and S/E Data Sheet November 213