LED BUILT-IN MODULES. LUGA Shop 2013 LED Modules COB for Retail Environments. LUGA SHOP 2013 HiCRI lm TO 5000 lm. LUGA SHOP 2013 HiCRI

Transcription

1 LED BUILT-IN MODULES LUGA SHOP 2013 HiCRI 2000 lm TO 5000 lm LUGA SHOP 2013 HiCRI LED MODULES COB FOR RETAIL ENVIRONMENTS WU-M-461, -462, -464 HiCRI Typical Applications Integration in reflector luminaires Shop lighting Furniture lighting Flat surface-mounting luminaires Cladding illumination Stairway and corridor illumination Suspended luminaire with external control gear LUGA Shop 2013 LONG SERVICE LIFETIME: 50,000 HOURS (L90; F10) ZHAGA-SHAPE HIGHLY EFFICIENT: UP TO 128 LM/W AT t p =65 C NARROW COLOUR TOLERANCES: 3 STEP MACADAMS (INITIAL) 4 STEP MACADAMS (AFTER 50,000 HRS) INTEGRATED THERMAL PROTECTION VDE APPROVED (ACC. TO EN 62031) pending

2 LUGA Shop 2013 LED Mo du les COB for Re tail En vi ron ments Technical Notes Di men sions: Ø 50 mm Use of ex ter nal LED cons tant cur rent dri ver Tem pe ra tu re fail-safe cir cuit (ac ti vat ion tem pe ra tu re: t c 105 C) On-board push-in con nec tor Electrical Characteristics Type Ref. No. Co lour Typ. voltage DC Typ. power consumption 0 ma 500 ma 700 ma 1050 ma 0 ma 500 ma 700 ma 1050 ma V V V V W W W W WU-M-461 All ty pes warm whi te / neut ral whi te WU-M-462 All ty pes warm whi te / neut ral whi te WU-M-464 All ty pes warm whi te / neut ral whi te Voltage and power tolerance: ±10 % Maximum Ratings Ex cee ding the ma xi mum ra tings can lead to re duc ti on of ser vi ce life or de struc ti on of the mo du les. Type Operating Operation temperature range Ambient temperature Storage temperature Max. allowed Max. permitted output voltage current ran ge at t c -point range range operating current of operating device ma C min. C max. C min. C max. C min. C max. ma V WU-M-461, WU-M-464 < > Optical Characteristics Type Ref. No. Co lour Correlated colour Typ. lumi nous flux** and efficiency at Typ. Typ. Zhaga Pho totemperature* 0 ma 500mA 700 ma 1050 ma beam CRI LES me tric K lm lm/w lm lm/w lm lm/w lm lm/w angle ( ) R a Cat. code WU-M warm whi te /349 WU-M warm whi te /349 WU-M neutral white /349 WU-M neutral white /349 WU-M warm whi te /349 WU-M warm whi te /349 WU-M neutral white /349 WU-M neutral white /349 WU-M warm whi te /349 WU-M warm whi te /349 WU-M neutral white /349 WU-M neutral white /349 * Co lour to ler an ce: 3 Ma ca dams ** Pro duc ti on to ler an ce of lu mi nous flux and ef fi cien cy: ± 10 % Min. CRI R a : > 90 Pa cking unit: 20 pcs. / 5 June, L UGA Shop 2013_HiCRI_GB 2 Operating Life Lu men WU-M-461 WU-M-462 WU-M-464 main ten an ce I F 700 ma I F 1050 ma I F 700 ma I F 1050 ma I F 700 ma I F 1050 ma L90/F10* 40,000 hrs. 26,000 hrs. 50,000 hrs.,000 hrs. 39,000 hrs. 18,000 hrs. L80/F10* 52,000 hrs. 41,000 hrs. 58,000 hrs. 47,000 hrs. 50,000 hrs.,000 hrs. L70/F10* 59,000 hrs. 48,000 hrs. 61,000 hrs. 51,000 hrs. 54,000 hrs. 39,000 hrs. * F10 includes the degradation B and total failure fraction C The va lu es con tai ned in this data sheet can chan ge due to tech ni cal in no vat ions. Any such chan ges will be made wit hout se pa ra te no ti fi ca ti on. Plea se find furt her de tai led in for ma ti on at loh-schwa be.com. Voss loh-schwa be Deutsch land GmbH Hohe Stei nert Lü den scheid Ger ma ny Pho ne /10 10 Fax / loh-schwa be.com 2

3 Typical Light Distribution Curve I (cd/klm) Mechanical Dimensions WU-M-461 WU-M-462, WU-M-464 LESø14.9 LESø tc/tp Ø tc/tp Ø Ø50 Ø50 Bins K 3850K 00K 3610K 3390K 3090K 3000K 2910K 2770K 2700K 2630K K LUGA Shop 2013_HiCRI_GB 3/5 June, 2013 Measurement tolerance x/y: ±

4 Assembly and Safety Information Installation must be carried out under observation of the relevant regulations and standards. The LED modules are designed for operation within a casing or luminaire. Installation must be carried out in a voltage-free state (i.e. disconnection from the mains). The following advice must be observed; non-observance can result in the destruction of the LED assembly modules, fire and/or other hazards. ESD (electrostatic discharge) protection measures must be observed when handling and installing the LED modules. See VS's application notes on ESD protection. LED assembly modules must not be subjected to any undue mechanical stress, e. g.: do not treat as bulk cargo avoid shear and compressive forces during handling and installation do not damage circuit paths do not touch the yellow phosphorus layer The module must be fixed onto a thermally conductive surface with three M3 screws. A torque of 0.6±0.1 Nm is required. Safe operation only possible by the use of external constant current sources (I max. see table "Electrical Characteristics"). Operation only with power supply units that feature the following protection: Short-circuit protection Overload protection Overheating protection SELV (Safety Extra Low Voltage); U max. 60 V I max. (see table "Maximum Ratings") must not be exceeded. When operating devices will be selected care has been taken to ensure that the maximum values (see table "Maximum Ratings") will not be exceeded. Please ensure the correct polarity of the leads prior to commissioning. Reversed polarity can destroy the modules. The LED modules are connected via two on-board push-in connectors for rigid or tinned conductors. Conductor section: tinned: mm² rigid: mm² Strip length: mm The contacts can be released with a flat-headed screwdriver with a width of 3 mm. Safety regulations acc. to EN (or further standards) has to be observed if the maximum output voltage exceed the permitted touchable value. Measurement tolerance of luminous flux (see table "Optical Characteristic"): ± 7 % (in addition to production tolerance). A parallel or serial connection of the modules is not allowed. To ensure problem-free operation, the specified maximum temperature at the t c point (see "Operating Life") must be observed (and measured in accordance with EN ). To satisfy this point, it may be necessary to put measures in place to ensure any heat is dissipated from the PCB to the environment. For optimized thermal heat transfer, a thermal conductive graphite foil is available (Ref. No.: ). In the event of outdoor applications or applications in damp locations, care must be taken to protect LED assembly modules against humidity, splashes and jets of water. Any corrosion damage resulting from humidity or contact with condensation will not be recognised as a defect or manufacturing fault. LED assembly modules are not specially protected against foreign bodies or dust. Depending on the type of application, further protection must be ensured to prevent dust and foreign bodies from entering. The photobiological safety of the LED modules must be classified into risk groups in accordance with EN 62471: general lighting exempt group: WU-M-461/-462/-464 other applications risk group 1: WU-M-461/-462/-464 Zhaga standard (Book 3) is applied for specific parameters (mechanical dimensions, LES). The LED modules are not Zhaga certified. Applied Standards EN LED modules for general lighting Safety specifications pending EN Photobiological safety of lamps and lamp systems EN LED modules for general lighting Performance requirements LUGA Shop 2013_HiCRI_GB 4/5 June,

5 Accessories Thermal conductive graphite tape Type: Thermal tape Ø 47.2 mm Graphite Thermal resistance: R th 0.04 K/W Ref. No.: R23,60 R2 Ø4 Reflectors: ACL-Lichttechnik GmbH Alux-Luxar GmbH & Co. KG JORDAN REFLEKTOREN GmbH & Co. KG Heat sinks with active cooling: AVC Nuventix, Inc. Sunon Heat sinks with passive cooling: ALPHA-Numerics GmbH AVC Fischer Elektronik GmbH & Co. KG Frigo Dynamics LED Constant Current Drivers Mains voltage: V ±10% Mains frequency: 0 Hz, Hz SELV-equivalent LUGA Shop 2013_HiCRI_GB 5/5 June, 2013 Constant current drivers 700 ma and 1050 ma Type: ECXe Current output: 700 ma Power: 40 W Ref. No.: Type: ECXe Current output: 1050 ma Power: 60 W Ref. No.: Dimmable constant current drivers 700 ma und 1050 ma DALI Type: ECXd Current output: 700 ma Voltage output: 9 48 V Power: 34 W Ref. No.: Type: ECXd Current output: 1050 ma Power: 60 W Ref. No.: () (130) () 23 (20) ()