Before commencing assembly,please read these instructions thoroughly.

Transcription

1 Thank you for choosing CYmodel Global : ustralia : Italia : Stinson Reliant Item Nr: CY805 Instruction Manual efore commencing assembly,please read these instructions thoroughly. LMOST - REDY - TO - FLY SFETY PRECUTIONS This radio control model is not a toy First-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent., ssemble this kit only in places out of children s reach Take enough safety precautions prior to operating this model., You are responsible for this models assembly and safe operation lways keep this instruction manual ready at hand for quick reference,even after completing the assembly. Could cause serious injury or even death SPECIFICTION Wing Span:00 mm (86.6in) Wing rea:60 dm (930sq.in) Total Length: 1550 mm (61 in) Engine : 6-35cc gas engine Radio : 5 channels,8 servos

2 REQUIRED FOR OPERTION (Purchase separately) 1 minimum 5channel radio for airplanes (with 8servos). nd dry batteries. CUTION: Only use a minimum 5channel radio for airplanes (No other radio may be used) minimum 5 channel transmitter for airplanes. 5 6 Glue required for engine starting WRNING: Normal gasoline cannot be used with glow engines. Epoxy Glue Instant glue Glow engine fuel only. 1 -size atteries Receiver remote control For handing the radio properly.refer to its instruction manual. attery 3 Servo(need 4 (need ) Switch (need ) 8 servos ) Engine and Muffler Model irplane engine:36-35cc GS engine 7 8 Fuel Pump Silicone Tube Other equipment for enhancing airplane operation & perormance Plug Wrench Fuel Filter Muffler Ignition 9 Engine Starter Purchase a propeller that will match your engine 1V attery (for starter) 16X X10 TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Driver wl Needle Nose Pliers Wire Cutters Scissors EFORE YOU EGIN Read through the manual before you begin,so you will have an overall idea of what to do. Check all parts.if you find any defective or missing parts.contact your local dealer. Symbols used throughout this instruction manual,comprise. pply epoxy glue. mm Drill holes with the specified Diameter(here:mm) Must be purchased separately Warning 50 C. pply instant glue (C glue,super glue). Ensure smooth non-binding movement while assembling. Pay close attention here Do not overlook this symbol. L R ssemble left and right Sides the same way. Cut off shaded portion. Cut off excess.

3 ccessory list for this page. 3 Install the aileron servo. 5X0mm - Horn x30mm X85mm rod Hinge - 4.6X1mm Tp x8mm L R Horn x30mm X85mm rod x8mm 1 Install the aileron 4 Main wing L R 5X0mm - Cut the film, put the aileron servo line into the fuselage 0X890mm tube Hinge Install the aileron servo. 5 Main wing Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents 3

4 ccessory list for this page. L R.1mm Collar mm Nylon collar 3X3mm Hinge X1 Tp mm wheel 6 Install the rudder&tail wheel 9 Install the elevator Hinge X95mm tube 7 Install the rudder&tail wheel 10 Horizontal/Vertical tail.1mm Collar D D.1mm Nylon collar 3X3mm X1 Tp E E C C D D E E 35mm wheel C C Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents 4

5 13 ccessory list for this page. Horn x30mm mm Steel wire luminium tube X0mm X150mm rod - 5Xmm 4X0mm Horn R --- x30mm x8mm x8mm L mm nut Install the elevator servo X150mm rod - 5mm lock nut 5.mm Collar 3X3mm 5mm Washer 4mm Washer 11 Install the rudder servo 14 Install the main landing gear 1 Install the rudder servo 15 Install the main landing gear HORN mm nut X8mm 1000mm Steel wire luminium tube X0mm Xmm 4X0mm 5mm Washer 4mm Washer 5 5mm lock nut 5.mm Collar 3X3mm

6 ccessory list for this page. 18 Install the throttle servo Linkage Stopper mm Nut 1.8X350mm Rod - - 3X3mm - - 3X16mm 3mm lock nut Linkage Stopper mm Nut 1.8X350mm Rod - - 3X3mm Install the wing support 19 ssembly of the full tank fter confirming the position(see front of fuel tank). Insert and tighten the. 3mm Fuel pipe ir pressure line 3X16mm 3mm lock nut Fuel supply line Engine:100cc gas 17 Install the engine 0 Radio Equipment Fuel tank 130mm Throttle servo attery/ignition attery Receiver 6

7 ccessory list for this page. 3 Install the door Latch loose sheet --.6X1mm Tp Canopy Canopy 1 Install the cover 4 Install the canopy Cut away the surplus pats of canopy care fully along the shaded line..6x1mm Tp Install the thr cowling Propeller Spinner Latch loose sheet --.6X1mm Tp

8 6 djustment. 8 djustment djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Side view ILERON Flap Rudder Side view Top view Top view 7 djustment. 9 djustment. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ELEVTOR Side view Never fly before checking the Cg s required position. In order to obtain the CG specified,reposition the receiver and battery mm CG Top view Warning NEVER fly the model without well balancing. 5 8