Test Reuslts Cat 6 Cable and Other Application Specific Cables

Transcription

1 CABLE MANUFACTURER CABLE P/N WIRE GAUGE CABLE TYPE MATERIAL CONCLUSION FOR THE EZ-RJ45 COMMENTARY BELDEN 7883A THE PAIRS ARE BONDED. IT IS BEST TO USE THE BELDEN PREPARATION TOOL P/N 1797B TO UN-BOND THE PAIRS. THERE CAN BE BURRS WHERE THE PAIRS WERE BONDED AND THESE NEED TO BE REMOVED OR THEY WILL PREVENT THE CONDUCTORS SLIDING THROUGH THE HOLES AT THE OTHER END OF THE EZ CONNECTOR. USING YOUR THUMB NAIL AND YOUR INDEX FINGER WORKS WELL. BELDEN 7881A BELDEN 7882A BELDEN 7989R BELDEN 1583A BELDEN 1700A BELDEN 2412 BELDEN 7988R BELDEN 7987R BELDEN AWG PVC THE HOLES IN THE END OF THE EZ CONNECTOR HAVE AN ID OF INCHES. 7881A CONDUCTORS HAVE AN OD OF 0.040" ON PAPER << 0.022"+0.009"+0.009">> BUT SINCE CABLE IS MADE AT THE MINUS END OF THE TOLERANCE, THE CONDUCTORS WILL SLIDE THROUGH THE 0.040" HOLES AT THE OTHER END OF THE EZ CONNECTOR. ALL TWISTS NEED TO BE COMBED OUT SO THAT EACH CONDUCTOR CAN LAY SIDE BY SIDE TIGHT WITH NO GAPS AND MAKE SURE THE ENDS ARE CUT CLEAN WITH NO BURRS. PLENUM READ 7881A COMMENTARY PVC NO OD OF CONDUCTORS TOO LARGE CAT 5E PVC SLAM DUNK CAT 5E PVC THE PAIRS ARE BONDED. IT IS BEST TO USE THE BELDEN PREPARATION TOOL P/N 1797B TO UN-BOND THE PAIRS. THERE CAN BE BURRS WHERE THE PAIRS WERE BONDED AND THESE NEED TO BE REMOVED OR THEY WILL PREVENT THE CONDUCTORS SLIDING THROUGH THE HOLES AT THE OTHER END OF THE EZ CONNECTOR. USING YOUR THUMB NAIL AND YOUR INDEX FINGER WORKS WELL. PVC SLAM DUNK CAT 5E PVC THE PAIRS ARE BONDED. IT IS BEST TO USE THE BELDEN PREPARATION TOOL P/N 1797B TO UN-BOND THE PAIRS. THERE CAN BE BURRS WHERE THE PAIRS WERE BONDED AND THESE NEED TO BE REMOVED OR THEY WILL PREVENT THE CONDUCTORS SLIDING THROUGH THE HOLES AT THE OTHER END OF THE EZ CONNECTOR. USING YOUR THUMB NAIL AND YOUR INDEX FINGER WORKS WELL. CAT 5E PVC SLAM DUNK CAT 5E PLENUM SLAM DUNK

2 BELDEN 7851A PVC NO BOTH THE CABLE JACKET OD AND THE CONDUCTORS OD ARE TOO LARGE. BELDEN 1872A PVC THE PAIRS ARE BONDED. IT IS BEST TO USE THE BELDEN PREPARATION TOOL P/N 1797B TO UN-BOND THE PAIRS. THERE CAN BE BURRS WHERE THE PAIRS WERE BONDED AND THESE NEED TO BE REMOVED OR THEY WILL PREVENT THE CONDUCTORS SLIDING THROUGH THE HOLES AT THE OTHER END OF THE EZ CONNECTOR. USING YOUR THUMB NAIL AND YOUR INDEX FINGER WORKS WELL. THE CABLE JACKET DESIGN IS AN ELLIPTICAL DESIGN BUT IT DOES SLIDE UP INTO THE CONNECTOR AND POSITIONS ITSELF WITH MINIMAL EFFORT. BELDEN 1318SB CAT 5E POLYOLEFIN BLACK LSZH THE CABLE IS A DUEL JACKET WHICH REQUIRES A DOUBLE STRIP. SET YOUR CABLE JACKET STRIPPER ON THE CABLE 2 1/2 INCHES FROM THE END OF THE CABLE. SCORE AND POP THE JACKET AND SLIDE OFF CABLE JACKET #1. THIS EXPOSES CABLE JACKET #2. NOW PLACE YOUR CABLE JACKET STRIPPER ON CABLE JACKET #2 APPRX 5/8 INCHES FROM THE END OF CABLE JACKET #1. SCORE AND POP AND SLIDE OFF EXPOSING ALL 4 CONDUCTOR PAIRS. NOW IT IS READY FOR THE STANDARD PREP. NOTE #1 = WHEN YOU SLIDE ON THE EZ-RJ45 CAT CONNECTOR, THE CABLE JACKET #2 GOES UP ALL THE WAY INSIDE THE EZ-RJ45 WITH THE END OF CABLE JACKET #1 SITTING AT THE END OF EZ-RJ45 CONNECTOR. NOTE #2 = EVEN THOUGH THIS CABLE IS A CAT5E CABLE, MUST USE THE EZ-RJ45 CAT FOR A SUCCESSFUL TERMINATION. BELDEN 1319SB POLYOLEFIN BLACK LSZH THE CABLE IS A DUEL JACKET WHICH REQUIRES A DOUBLE STRIP. SET YOUR CABLE JACKET STRIPPER ON THE CABLE 2 1/2 INCHES FROM THE END OF THE CABLE. SCORE AND POP THE JACKET AND SLIDE OFF CABLE JACKET #1. THIS EXPOSES CABLE JACKET #2. NOW PLACE YOUR CABLE JACKET STRIPPER ON CABLE JACKET #2 APPRX 5/8 INCHES FROM THE END OF CABLE JACKET #1. SCORE AND POP AND SLIDE OFF EXPOSING ALL 4 CONDUCTOR PAIRS. NOW IT IS READY FOR THE STANDARD PREP. NOTE #1 = WHEN YOU SLIDE ON THE EZ-RJ45 CAT CONNECTOR, THE CABLE JACKET #2 GOES UP ALL THE WAY INSIDE THE EZ-RJ45 WITH THE END OF CABLE JACKET #1 SITTING AT THE END OF EZ-RJ45 CONNECTOR. HITACHI HITACHI HITACHI HITACHI CAT 5E CAT 5E RISER EASY TO TERMINATE CAT 5E CAT 5E RISER EASY TO TERMINATE

3 HITACHI HITACHI HITACHI HITACHI HITACHI HITACHI HITACHI PLUS RISER EASY TO TERMINATE PLUS PREMIUM PLENUM PREMIUM RISER SUPRA 0 PLENUM SUPRA 0 RISER SUPRA 10G PLENUM NO EASY TO TERMINATE EASY TO TERMINATE EASY TO TERMINATE EASY TO TERMINATE THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES HITACHI SUPRA 10G RISER NO THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES M5889 NET M57202 NET M57203 NET M57204 NET M57205 NET M5720 NET

4 M57207 NET M57208 NET M57209 NET M57210 NET M5905 NET M57193 NET M57194 NET M57195 NET M5719 NET M57197 NET M57198 NET M57199 NET M57200 NET M57201 NET

5 M57413 M57414 M57415 M5741 M57417 M5720 M57750 M5780 M5781 M578 M57418 M57419 M57420 M57421 M57422 M5721 M5787 M57870 M5788 M5789 M58291

6 M58292 M58293 M58294 M58295 M5829 M58297 M58298 M58299 M58300 M58280 M58281 M58282 M58283 M58284 M58285 M5828 M58287 M58288 M58289 M58290 M55988

7 M518 M5092 M5093 M5882 M51 M5072 M587 M5877 M5878 M55989 M517 M5094 M5095 M515

8 M57048 M5954 M570 M57129 M574 WEST PENN 424 WEST PENN BERK TEK BERK TEK BERK TEK BERK TEK BERK TEK BERK TEK BERK TEK LANMARK- 10G2 SERIES LANMARK- 10G2 SERIES LANMARK- SERIES LANMARK- SERIES LANMARK SERIES LANMARK SERIES LANMARK SERIES CATA CMR RISER NO CATA CMP PLENUM NO NON-PLENUM CMR RISER PLENUM CMP NON-PLENUM CMR RISER PLENUM CMP NON-PLENUM CMR RISER THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT! CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT! CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT! CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT! CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT!

9 LANMARK- BERK TEK 1000 SERIES NEXTGAIN SUPERIOR ESSEX SERIES NEXTGAIN SUPERIOR ESSEX SERIES DATAGAIN SUPERIOR ESSEX SERIES SUPERIOR ESSEX SUPERIOR ESSEX SUPERIOR ESSEX SUPERIOR ESSEX AMP NETCONNECT AMP NETCONNECT 10 GAIN SERIES 10 GAIN SERIES S-220-XA S-220-XB SERIES SERIES PLENUM CMP PVC / CMR PVC / CMP + LIMITED COMBUSTIBLE 22 AWG A PVC / CMP NO 22 AWG A PVC / CMR NO A STP U/FTP PVC RISER NO A STP U/FTP PLENUM LOW SMOKE GRADE PVC PVC CMR RISER RATED FR PVC CMP PLENUM RATED NO (AND SOMETIMES, MAYBE 'NO') SEE NEXT COLUMN. CABLE JACKET OD IS 0.22 INCHES AND THE CONDUCTOR OD IS INCHES. WORKS GREAT! EASY TO TERMINATE EASY TO TERMINATE EASY TO TERMINATE THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES, IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES, IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES, IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES THIS IS A 10 GIG CABLE AND THE EZ-RJ45 CAT CONNECTOR WILL NOT MEET THE REQUIRED SPECS AND IN MOST CASES, IF NOT ALL, THE 10 GIG CABLES ARE WAY TOO LARGE TO EVEN CONSIDER TERMINATING WITH A NORMAL TYPE DESIGNED RJ45 CONNECTOR. FOR REFERENCE, THE CABLE JACKET OD = INCHES AND THE CONDUCTOR OD = INCHES THE PAPER/PRINTED SPEC IS REFERENCED THE OD OF THE CONDUCTORS AS INCHES NOMINAL WHICH WOULD NOT WORK SINCE THE HOLES IN THE END OF THE CONNECTOR ARE INCHES...BUT...IN THE REAL WORLD, THE SAMPLE OF THIS CABLE USED FOR TESTING, WORKS. AS FOR THE CABLE JACKET OD, IT WORKS GREAT, ONLY INCHES! CABLE JACKET OD IS INCHES, WHICH WORKS GREAT AND THE OD OF THE CONDUCTORS IS INCHES WHICH IS A 'GO'

10 AMP NETCONNECT AMP NETCONNECT AMP NETCONNECT AMP NETCONNECT SERIES SERIES SERIES SERIES CCI COLEMAN CABLE CCI COLEMAN CABLE GENERAL CABLE GENERAL CABLE GENERAL CABLE GENERAL CABLE GENERAL CABLE GENERAL CABLE GENERAL CABLE GEN SPEED 000 SERIES GEN SPEED 00 SERIES GEN SPEED 00 SERIES GEN SPEED 000 SERIES GEN SPEED 000 SERIES GEN SPEED 500 SERIES GEN SPEED 500 SERIES A FTP A FTP E UTP A UTP PVC CMR RISER RATED FR PVC CMP PLENUM RATED PVC CMR RISER RATED FEP CMP PLENUM ATED NO NO (AND SOMETIMES, MAYBE 'NO') SEE NEXT COLUMN. CMR RISER CMP PLENUM BOTH THE CABLE JACKET OD(0.300 INCHES) AND THE CONDUCTOR OD (0.044 INCHES) ARE TOO LARGE BOTH THE CABLE JACKET OD(0.300 INCHES) AND THE CONDUCTOR OD (0.044 INCHES) ARE TOO LARGE CABLE JACKET OD IS INCHES, WHICH WORKS GREAT AND THE OD OF THE CONDUCTORS IS INCHES WHICH IS A 'GO' THE PAPER/PRINTED SPEC IS REFERENCED THE OD OF THE CONDUCTORS AS INCHES NOMINAL WHICH WOULD NOT WORK SINCE THE HOLES IN THE END OF THE CONNECTOR ARE INCHES...BUT...IN THE REAL WORLD, THE SAMPLE OF THIS CABLE USED FOR TESTING, WORKS. AS FOR THE CABLE JACKET OD, IT WORKS GREAT, ONLY INCHES! CABLE JACKET OD IS INCHES WITH A CONDUCTOR OD OF INCHES. NOTE = BE SURE TO COMB OUT ALL THE KINKS SO ALL 8 CONDUCTORS LIE SIDE BY SIDE WITHOUT ANY GAPS! CABLE JACKET OD IS INCHES WITH A CONDUCTOR OD OF INCHES. OUTSIDE PLANT TYPE CABLE BLK UV RESISTNT THE CABLE JACKET OD IS ONLY INCHES. THE CABLE JACKET OD IS 0.20 INCHES AND THAT WILL WORK BUT I NON-PLENUM HAVE NO SPECS TO CALCULATE THE OD OF THE CONDUCTORS OR AN CMR RISER??? ACTUAL SAMPLE TO DO A REAL WORLD TEST, SO I HAVE TO USE??? PLENUM CMP??? ENHANCE D + + THE CABLE JACKET OD IS INCHES AND THAT WILL WORK BUT I HAVE NO SPECS TO CALCULATE THE OD OF THE CONDUCTORS OR AN ACTUAL SAMPLE TO DO A REAL WORLD TEST, SO I HAVE TO USE??? NON-PLENUM CMR RISER CABLE JACKET OD IS INCHES. WORKS GREAT! ENHANCE D + PLENUM CMP CABLE JACKET OD IS INCHES. WORKS GREAT! NON-PLENUM CMR RISER + PLENUM CMP CABLE JACKET OD IS INCHES. I DO NOT HAVE THE SPECS TO DETERMINE THE CONDUCTOR OD BUT BASED ON WHAT I DO HAVE, SHOULD WORK FINE. IMPORTANT TO COMB OUT ALL THE TWISTS, MAKING SURE ALL 8 CONDUCTORS LIE SIDE BY SIDE WITH NO GAPS. CABLE JACKET OD IS INCHES. I DO NOT HAVE THE SPECS TO DETERMINE THE CONDUCTOR OD BUT BASED ON WHAT I DO HAVE, SHOULD WORK FINE. IMPORTANT TO COMB OUT ALL THE TWISTS, MAKING SURE ALL 8 CONDUCTORS LIE SIDE BY SIDE WITH NO GAPS.

11 ALPHA WIRE ALPHA WIRE 904R 904F RISER CMR PLENUM CMP THE CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES. THE CABLE JACKET OD IS INCHES AND THE CONDUCTOR OD IS INCHES.

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27