isd dunaferr Product catalogue

Transcription

1 isd dunaferr Product catalogue COLD BENT STEEL SECTIONS (Open and hollow) Cold bent steel sections are produced from slit coils by continuous roller bending, using section-shaped pairs of rolls mounted into stands behind each other. Hollow sections are produced by welding the two edges of the strip bent to a round section to each other by high-frequency induction welding. The outer welding seam is planed-off and then the section is calibrated to the required shape and dimension. The cut-to-length process is performed by sawing-disc. STEEL GRADES The base material of cold bent steel sections is generally cold or hot rolled steel strip with the yield strength of at least 235 N/mm 2. Mostly applied steel grades Number Relevant standards Title S235JR EN Hot rolled products from structrual steels Part 2: Technical terms of delivery of non-alloy structural steels E235 EN EN Precision steel tubes. Technical terms of delivery Part 3: Welded, cold formed tubes Precision steel tubes. Technical terms of delivery Part 5: Welded, cold formed, square and rectangular tubes S235JRH EN Cold formed, welded, hollow sections for the production of steel structures, from unalloyed and fine-grained steels Part 1: Technical terms of delivery 1. MAIN PARAMETERS 1.1. STEEL SECTION DIMENSIONS Hollow sections Wall thickness; s (mm) Overall dimensions of sections (mm) Length; l (m) Round Square x15 100x Rectangular x10 150x Open sections Wall thickness; s (mm) Overall dimensions of sections (mm) Length; l (m) U L L C Z Dimensional limits of sections cut to precise lengths Outside dimension of section (mm) With burring Without burring Outside diameter of round hollow steel section (mm) Outside diameter of square hollow steel section (b b) (mm) Outside diameter of rectangular hollow steel section (h b) (mm) Wall thickness min. O 16 O 16 max. O 80 O 95 min. o o max. o o min * max * According to the assortment * The base side cannot be longer than twice of the height. Dimensional limits of the recise length: with burring mm without burring mm

2 1.2. TECHNICAL REQUIREMENTS Product group General technical requirements Dimensions Open steel sections For general and for steel structures EN According to detailed product catalogue Cold Bent Steel Sections of ISD DUNAFERR Zrt. or based on agreement For special purpose Based on agreement Hollow steel sections For general purpose EN , EN For steel structures EN EN For special purpose Based on agreement 2. PRODUCT GROUPS 2.1. GENERALLY USED OPEN STEEL SECTIONS Typical applications: construction, automotive, mechanical engineering and other products (e.g. containers). Main product groups Overall dimensions min. max. (mm) h b c s U Cold bent U-section L Cold bent equal sided L-section L Cold bent unequal sided L-section C Cold bent C-section Z Cold bent Z-section

3 2.2. ASSORTMENT OF ROUND HOLLOW SECTIONS FOR GENERAL PURPOSE AND FOR STEEL STRUCTURES Typical applications: construction, automotive, mechanical engineering and other products (e.g. road poles and supporting structures). Outside diameter (mm) Unit weight (according to EN and EN standards) (kg/m) Thickness; s (mm) The following limitations refer to the assortment of steel sections for steel structures (EN 10219): Round steel sections are made only of hot rolled base material with the thickness of minimum 2 mm; their outside diameter is minimum 21.3 mm (see marking). 3

4 2.3. ASSORTMENT OF RECTANGULAR HOLLOW STEEL SECTIONS FOR GENERAL PURPOSE Typical applications: Overall dimensions h b (mm) automotive, mechanical engineering and other products (fences, containers etc.). Unit weight (according to EN standard) (kg/m) Thickness; s (mm) , , , , , , , , , x50, 60x x50, 70x , , x , , , , , ,

5 2.4. ASSORTMENT OF RECTANGULAR HOLLOW STEEL SECTIONS FOR STEEL STRUCTURES Typical applications: construction, automotive, mechanical engineering and other products (e.g. containers, road poles and supporting structures). Overall dimensions h b (mm) Unit weight (according to EN standard) (kg/m) Thickness; s (mm) , , , , , , , , , , , , , , , , SPECIAL PRODUCTS Detailed assortment and sectional characteristics of cold bent steel sections are included in the detailed product catalogue Cold Bent Steel Sections of ISD DUNAFERR Co. Ltd. We undertake to meet special demands based on agreement. 4. SURFACE The smoothness of the surface of cold bent steel sections is in accordance with the base material used for production. Visible cracks are not permitted on the surface of bent edges. Longitudinal scratches, impressions and roll-imprints on the surface of steel sections as a result of bending, not exceeding the section thickness tolerance value, cannot be claimed. 5

6 5. TOLERANCES 5.1. TOLERANCES OF OPEN STEEL SECTIONS Dimension tolerances of open steel sections for general purpose and for steel structures according to the specification of EN standard are as follows: Tolerance of side length (outside dimension of the section part between two bending): Thickness of the section; s (mm) Tolerance of the side length Dimension of the side (mm) 40 > > > s 1.5 ±0.50 ±0.50 ±0.75 ± < s 3.0 ±0.75 ±0.75 ±1.00 ± < s 6.0 ±1.00 ±1.00 ±1.25 ±1.75 Tolerance of free side length (outside dimension of the section part between the edge of the free side and the closest bending): Thickness of the section; s (mm) Tolerance of the side length Dimension of the side (mm) 40 > > s 1.5 ±0.75 ±0.75 ± < s 3.0 ±0.80 ±1.00 ± < s 6.0 ±1.00 ±1.25 ±1.50 Note: in case of different side lengths tolerance of the larger side is normative for all side. Tolerance of the bending angle: Length of the smaller side, as well as the free side; l (mm) Tolerance of the bending angle l 10 ± 3 10 < l 40 ± < l 80 ± < l 110 ± < l ± 0 45 Tolerance of the section thickness: Thickness tolerance (mm) Thickness; s (mm) Cold rolled EN Hot rolled EN s 1.0 ± < s 1.2 ± < s 1.6 ± 0.08 ± < s 2.0 ± 0.10 ± < s 2.5 ± 0.12 ± < s 3.0 ± < s 4.0 ± < s 5.0 ± < s 6.0 ± The value of inside bending radius depends on the grade and thickness of the used steel strip. In case of steels with a yield strength of minimum 235 N/mm 2 inside bending radius is generally equal to the thickness of the section. Tolerance of the inside bending radius: ± 20%, but minimum 0.5 mm.

7 Straightness: The deviation of straightness (e) of any steel sections length (L) measured shall not exceed L. Torsion: Torsion of steel sections is maximum 1 /m. Convexity, concavity: Convexity and concavity of steel sections are allowed within the dimensional tolerances. Dimension control: Cross section dimensions of open steel sections are to be controlled at a distance of minimum 250 mm from the ends of the single profile due to the torsion of cutting TOLERANCES OF THE HOLLOW STEEL SECTIONS Tolerances of hollow steel sections with a yield strength of minimum 235 N/mm 2 : Tolerances Parameters For general purposes EN ; -5 For steel structures EN ; -2 Thickness; s (mm) Round steel sections s 1.5 ±0.15 mm 1.5 < s < 2 s ³ 2 Outside diameter (d) 10% of the thickness ±, but maximum ±0.35 mm ±1% of the dimension ±10% of thickness ±1% of thickness, but minimum ± 0.5 mm Oval characteristics 2% 2% Straightness difference 0.20% of total length, maximum 3 mm on the length of 1 m 0.20% of total length Edge or outer radius (r) Outside dimension of edge if s 2.5 a 1.5 s if s > 2.5 a 2.2 s Outside radius r = 1.6 s 2.4 s Side angle 90 ± 1 90 ± 1 Convexity or concavity of wall Within the dimensional tolerances of outside dimensions 0.8%, but minimum 0.5 mm Torsion if wall dimension is 30 mm, 3 mm; if wall dimension is 30 mm, 10% of sidewall dimension 2 mm mm/m length Rectangular steel sections Straightness difference 0.25% of total length, if the length of walls the shorter wall in case of rectangular steel section is 30 mm, maximum 3 mm on a length of 1 m as well as 0.15% of total length, if the length of walls the shorter wall in case of rectangular steel section is 30 mm, maximum 3 mm on a length of 1 m 0.15% of total length, as well as 3 mm on any lengths of 1 m Outside dimensions (mm) h longer wall b shorter wall Tolerances of dimensions h and b, if the value of h is: h 20 ± < h 35 ± < h 50 ± < h 60 ± < h 70 ± < h 80 ± < h 90 ± < h 100 ± < h 150 ±0.70 Wall length: h, b < 100 Tolerance: ±1%, but minimum ± 0.5 mm 100 h., b 200 ±0.8% Dimension control: All outside dimensions of steel sections for steel structures are to be controlled minimum d from the ends in case of round hollow steel sections, minimum b from the ends in case of square hollow steel sections, minimum h from the ends in case of rectangular steel sections, but minimum 100 mm from the ends due to the torsion of cutting. All outside dimensions of hollow steel sections for general purposes are to be controlled at least 100 mm from the ends. 7

8 5.3. TOLERANCES OF HOLLOW STEEL SECTIONS CUT TO PRECISE LENGTH, WITH BURRING Dimensional limits: Dimensional limits of the precise length (mm) Precise length; l (mm) EN EN EN EN as requested l 500 based on agreement 500 < l mm < l mm mm ± 0.5 mm or + 1 mm ± 1 mm or + 2 mm 6. DELIVERY CONDITION Steel sections are not tempered after cold forming. The smoothness of the surface of cold bent steel sections is in accordance with the base material used for production. The welding bead of hollow steel sections is machined off outside and it is not removed inside. The welding seam of rectangular steel sections is on the longer side of the section. On the outside and inside surface of steel sections emulsion residues deriving from manufacturing, as well as smaller iron stains are allowed. An oil coat providing temporary corrosion protection is applied during the manufacturing process on the outside surface of steel sections, the omission of which has to be agreed on separately. The fulfilment of any demand regarding hot dip galvanizing or other special requirement has to be agreed. 7. PACKAGING Unless otherwise agreed, the weight of the bundle in case of open and hollow steel sections is t. Several bundles tied together can be conveyed by crane too. Possible packaging of bundles is subject to a separate agreement. Our products are delivered without packaging, strapped. 8. APPROBATED (CERTIFIED) PRODUCTS Hollow sections with CE-mark produced according to EN :2006 for the purpose of construction according to 93/68/EEC Certified by: TÜV Rheinland LGA Bautechnik GmbH Open sections with CE-mark produced according to EN 10162:2003 for the purpose of construction according to 93/68/EWG Certified by: LGA Bautechnik GmbH The products made by ISD DUNAFERR Co. Ltd. are always supplied with a Conformity Statement of Producer and agreement shall be reached about the type of statement at the time of placing the order. The available types of statements are included by standard MSZ EN 10204:2005. Certifications are available on the website ISD DUNAFERR Co. Ltd. SALES Address: H 2400 Dunaújváros, Vasmű tér 1 3. Phone: +36 (25) Fax: +36 (25) , +36 (25) profile.sales@isd-dunaferr.hu Web: